dt-bindings:iio:adc: Another set of yaml conversions.

new file mode 100644
index 000000000000..99b6b55fd0a3
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/fsl,vf610-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ADC found on Freescale vf610 and similar SoCs
+
+maintainers:
+  - Fugang Duan <[email protected]>
+
+description:
+  ADCs found on vf610/i.MX6slx and upward SoCs from Freescale.
+
+properties:
+  compatible:
+    const: fsl,vf610-adc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: ADC source clock (ipg clock)
+    maxItems: 1
+
+  clock-names:
+    const: adc
+
+  vref-supply:
+    description: ADC reference voltage supply.
+
+  fsl,adck-max-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 3
+    maxItems: 3
+    description: |
+      Maximum frequencies from datasheet operating requirements.
+      Three values necessary to cover the 3 conversion modes.
+      * Frequency in normal mode (ADLPC=0, ADHSC=0)
+      * Frequency in high-speed mode (ADLPC=0, ADHSC=1)
+      * Frequency in low-power mode (ADLPC=1, ADHSC=0)
+
+  min-sample-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Minimum sampling time in nanoseconds. This value has
+      to be chosen according to the conversion mode and the connected analog
+      source resistance (R_as) and capacitance (C_as). Refer the datasheet's
+      operating requirements. A safe default across a wide range of R_as and
+      C_as as well as conversion modes is 1000ns.
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - vref-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/vf610-clock.h>
+    adc@4003b000 {
+        compatible = "fsl,vf610-adc";
+        reg = <0x4003b000 0x1000>;
+        interrupts = <0 53 0x04>;
+        clocks = <&clks VF610_CLK_ADC0>;
+        clock-names = "adc";
+        fsl,adck-max-frequency = <30000000>, <40000000>, <20000000>;
+        vref-supply = <&reg_vcc_3v3_mcu>;
+        min-sample-time = <10000>;
+    };
+...

deleted file mode 100644
index 1aad0514e647..000000000000
@@ -1,36 +0,0 @@
-Freescale vf610 Analog to Digital Converter bindings
-
-The devicetree bindings are for the new ADC driver written for
-vf610/i.MX6slx and upward SoCs from Freescale.
-
-Required properties:
-- compatible: Should contain "fsl,vf610-adc"
-- reg: Offset and length of the register set for the device
-- interrupts: Should contain the interrupt for the device
-- clocks: The clock is needed by the ADC controller, ADC clock source is ipg clock.
-- clock-names: Must contain "adc", matching entry in the clocks property.
-- vref-supply: The regulator supply ADC reference voltage.
-
-Recommended properties:
-- fsl,adck-max-frequency: Maximum frequencies according to datasheets operating
-  requirements. Three values are required, depending on conversion mode:
-  - Frequency in normal mode (ADLPC=0, ADHSC=0)
-  - Frequency in high-speed mode (ADLPC=0, ADHSC=1)
-  - Frequency in low-power mode (ADLPC=1, ADHSC=0)
-- min-sample-time: Minimum sampling time in nanoseconds. This value has
-  to be chosen according to the conversion mode and the connected analog
-  source resistance (R_as) and capacitance (C_as). Refer the datasheet's
-  operating requirements. A safe default across a wide range of R_as and
-  C_as as well as conversion modes is 1000ns.
-
-Example:
-adc0: adc@4003b000 {
-	compatible = "fsl,vf610-adc";
-	reg = <0x4003b000 0x1000>;
-	interrupts = <0 53 0x04>;
-	clocks = <&clks VF610_CLK_ADC0>;
-	clock-names = "adc";
-	fsl,adck-max-frequency = <30000000>, <40000000>,
-				<20000000>;
-	vref-supply = <&reg_vcc_3v3_mcu>;
-};

new file mode 100644
index 000000000000..6781ad2f0f51
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/ti,twl4030-madc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MADC subsystem in the TWL4030 power module
+
+maintainers:
+  - Sebastian Reichel <[email protected]>
+
+description:
+  The MADC subsystem in the TWL4030 consists of a 10-bit ADC
+  combined with a 16-input analog multiplexer.
+
+properties:
+  compatible:
+    const: ti,twl4030-madc
+
+  interrupts:
+    maxItems: 1
+
+  ti,system-uses-second-madc-irq:
+    type: boolean
+    description:
+      Set if the second madc irq register should be used, which is intended
+      to be used  by Co-Processors (e.g. a modem).
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - interrupts
+  - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    twl {
+        madc {
+            compatible = "ti,twl4030-madc";
+            interrupts = <3>;
+            #io-channel-cells = <1>;
+        };
+    };
+...

deleted file mode 100644
index 6bdd21404b57..000000000000
@@ -1,24 +0,0 @@
-* TWL4030 Monitoring Analog to Digital Converter (MADC)
-
-The MADC subsystem in the TWL4030 consists of a 10-bit ADC
-combined with a 16-input analog multiplexer.
-
-Required properties:
-  - compatible: Should contain "ti,twl4030-madc".
-  - interrupts: IRQ line for the MADC submodule.
-  - #io-channel-cells: Should be set to <1>.
-
-Optional properties:
-  - ti,system-uses-second-madc-irq: boolean, set if the second madc irq register
-				    should be used, which is intended to be used
-				    by Co-Processors (e.g. a modem).
-
-Example:
-
-&twl {
-	madc {
-		compatible = "ti,twl4030-madc";
-		interrupts = <3>;
-		#io-channel-cells = <1>;
-	};
-};

new file mode 100644
index 000000000000..9049c699152f
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/st,stmpe-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ADC on an STMPE multifunction device.
+
+maintainers:
+  - Stefan Agner <[email protected]>
+
+description:
+  This ADC forms part of an ST microelectronics STMPE multifunction device .
+  The ADC is shared with the STMPE touchscreen. As a result some ADC related
+  settings are specified in the parent node.
+  The node name myst be stmpe_adc and should be a child node of the stmpe node
+  to which it belongs.
+
+properties:
+  compatible:
+    const: st,stmpe-adc
+
+  st,norequest-mask:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Bitmask specifying which ADC channels should _not_ be
+      requestable due to different usage (e.g. touch).
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    stmpe {
+        stmpe_adc {
+            compatible = "st,stmpe-adc";
+            st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */
+        };
+    };
+...

deleted file mode 100644
index 480e66422625..000000000000
@@ -1,21 +0,0 @@
-STMPE ADC driver
-----------------
-
-Required properties:
- - compatible: "st,stmpe-adc"
-
-Optional properties:
-Note that the ADC is shared with the STMPE touchscreen. ADC related settings
-have to be done in the mfd.
-- st,norequest-mask: bitmask specifying which ADC channels should _not_ be
-  requestable due to different usage (e.g. touch)
-
-Node name must be stmpe_adc and should be child node of stmpe node to
-which it belongs.
-
-Example:
-
-	stmpe_adc {
-		compatible = "st,stmpe-adc";
-		st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */
-	};

new file mode 100644
index 000000000000..09018487d690
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/aspeed,ast2400-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ADC that forms part of an ASPEED server management processor.
+
+maintainers:
+  - Rick Altherr <[email protected]>
+
+description:
+  This device is a 10-bit converter for 16 voltage channels.  All inputs are
+  single ended.
+
+properties:
+  compatible:
+    enum:
+      - aspeed,ast2400-adc
+      - aspeed,ast2500-adc
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    description:
+      Input clock used to derive the sample clock. Expected to be the
+      SoC's APB clock.
+
+  resets: true
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - resets
+  - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/aspeed-clock.h>
+    adc@1e6e9000 {
+        compatible = "aspeed,ast2400-adc";
+        reg = <0x1e6e9000 0xb0>;
+        clocks = <&syscon ASPEED_CLK_APB>;
+        resets = <&syscon ASPEED_RESET_ADC>;
+        #io-channel-cells = <1>;
+    };
+...

deleted file mode 100644
index 034fc2ba100e..000000000000
@@ -1,22 +0,0 @@
-Aspeed ADC
-
-This device is a 10-bit converter for 16 voltage channels.  All inputs are
-single ended.
-
-Required properties:
-- compatible: Should be "aspeed,ast2400-adc" or "aspeed,ast2500-adc"
-- reg: memory window mapping address and length
-- clocks: Input clock used to derive the sample clock. Expected to be the
-          SoC's APB clock.
-- resets: Reset controller phandle
-- #io-channel-cells: Must be set to <1> to indicate channels are selected
-                     by index.
-
-Example:
-	adc@1e6e9000 {
-		compatible = "aspeed,ast2400-adc";
-		reg = <0x1e6e9000 0xb0>;
-		clocks = <&syscon ASPEED_CLK_APB>;
-		resets = <&syscon ASPEED_RESET_ADC>;
-		#io-channel-cells = <1>;
-	};

deleted file mode 100644
index 908334c6b07f..000000000000
@@ -1,19 +0,0 @@
-* Berlin Analog to Digital Converter (ADC)
-
-The Berlin ADC has 8 channels, with one connected to a temperature sensor.
-It is part of the system controller register set. The ADC node should be a
-sub-node of the system controller node.
-
-Required properties:
-- compatible: must be "marvell,berlin2-adc"
-- interrupts: the interrupts for the ADC and the temperature sensor
-- interrupt-names: should be "adc" and "tsen"
-
-Example:
-
-adc: adc {
-	compatible = "marvell,berlin2-adc";
-	interrupt-parent = <&sic>;
-	interrupts = <12>, <14>;
-	interrupt-names = "adc", "tsen";
-};

50 lines not on this page · raw message

new file mode 100644
index 000000000000..57df6439dd9d
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/sprd,sc2720-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Spreadtrum SC27XX series PMICs ADC binding
+
+maintainers:
+  - Baolin Wang <[email protected]>
+
+description:
+  Supports the ADC found on these PMICs.
+
+properties:
+  compatible:
+    enum:
+      - sprd,sc2720-adc
+      - sprd,sc2721-adc
+      - sprd,sc2723-adc
+      - sprd,sc2730-adc
+      - sprd,sc2731-adc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#io-channel-cells":
+    const: 1
+
+  hwlocks:
+    maxItems: 1
+
+  nvmem-cells:
+    maxItems: 2
+    
+  nvmem-cell-names:
+    items:
+      - const: big_scale_calib
+      - const: small_scale_calib
+      
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#io-channel-cells"
+  - hwlocks
+  - nvmem-cells
+  - nvmem-cell-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    pmic {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        adc@480 {
+            compatible = "sprd,sc2731-adc";
+            reg = <0x480>;
+            interrupt-parent = <&sc2731_pmic>;
+            interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+            #io-channel-cells = <1>;
+            hwlocks = <&hwlock 4>;
+            nvmem-cells = <&adc_big_scale>, <&adc_small_scale>;
+            nvmem-cell-names = "big_scale_calib", "small_scale_calib";
+        };
+    };
+...

deleted file mode 100644
index b4daa15dcf15..000000000000
@@ -1,40 +0,0 @@
-Spreadtrum SC27XX series PMICs ADC binding
-
-Required properties:
-- compatible: Should be one of the following.
-	"sprd,sc2720-adc"
-	"sprd,sc2721-adc"
-	"sprd,sc2723-adc"
-	"sprd,sc2730-adc"
-	"sprd,sc2731-adc"
-- reg: The address offset of ADC controller.
-- interrupt-parent: The interrupt controller.
-- interrupts: The interrupt number for the ADC device.
-- #io-channel-cells: Number of cells in an IIO specifier.
-- hwlocks: Reference to a phandle of a hwlock provider node.
-- nvmem-cells: A phandle to the calibration cells provided by eFuse device.
-- nvmem-cell-names: Should be "big_scale_calib", "small_scale_calib".
-
-Example:
-
-	sc2731_pmic: pmic@0 {
-		compatible = "sprd,sc2731";
-		reg = <0>;
-		spi-max-frequency = <26000000>;
-		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pmic_adc: adc@480 {
-			compatible = "sprd,sc2731-adc";
-			reg = <0x480>;
-			interrupt-parent = <&sc2731_pmic>;
-			interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-			#io-channel-cells = <1>;
-			hwlocks = <&hwlock 4>;
-			nvmem-cells = <&adc_big_scale>, <&adc_small_scale>;
-			nvmem-cell-names = "big_scale_calib", "small_scale_calib";
-		};
-	};

new file mode 100644
index 000000000000..bcd041ea28a8
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/nuvoton,nau7802.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton NAU7802 I2c Analog to Digital Converter (ADC)
+
+maintainers:
+  - Alexandre Belloni <[email protected]>
+  - Maxime Ripard <[email protected]>
+
+properties:
+  compatible:
+    const: nuvoton,nau7802
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  nuvoton,vldo:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Internal reference voltage in millivolts to be configured.
+    minimum: 2400
+    maximum: 4500
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        nau7802@2a {
+            compatible = "nuvoton,nau7802";
+            reg = <0x2a>;
+            nuvoton,vldo = <3000>;
+        };
+    };
+...

deleted file mode 100644
index e9582e6fe350..000000000000
@@ -1,18 +0,0 @@
-* Nuvoton NAU7802 Analog to Digital Converter (ADC)
-
-Required properties:
-  - compatible: Should be "nuvoton,nau7802"
-  - reg: Should contain the ADC I2C address
-
-Optional properties:
-  - nuvoton,vldo: Internal reference voltage in millivolts to be
-    configured valid values are between 2400 mV and 4500 mV.
-  - interrupts: IRQ line for the ADC. If not used the driver will use
-    polling.
-
-Example:
-adc2: nau7802@2a {
-	compatible = "nuvoton,nau7802";
-	reg = <0x2a>;
-	nuvoton,vldo = <3000>;
-};

deleted file mode 100644
index ef8eeec1a997..000000000000
@@ -1,26 +0,0 @@
-Nuvoton NPCM Analog to Digital Converter (ADC)
-
-The NPCM ADC is a 10-bit converter for eight channel inputs.
-
-Required properties:
-- compatible: "nuvoton,npcm750-adc" for the NPCM7XX BMC.
-- reg: specifies physical base address and size of the registers.
-- interrupts: Contain the ADC interrupt with flags for falling edge.
-- resets : phandle to the reset control for this device.
-
-Optional properties:
-- clocks: phandle of ADC reference clock, in case the clock is not
-		  added the ADC will use the default ADC sample rate.
-- vref-supply: The regulator supply ADC reference voltage, in case the
-			   vref-supply is not added the ADC will use internal voltage
-			   reference.
-
-Example:
-
-adc: adc@f000c000 {
-	compatible = "nuvoton,npcm750-adc";
-	reg = <0xf000c000 0x8>;
-	interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
-	clocks = <&clk NPCM7XX_CLK_ADC>;
-	resets = <&rstc NPCM7XX_RESET_IPSRST1 NPCM7XX_RESET_ADC>;
-};

64 lines not on this page · raw message

deleted file mode 100644
index 9ada5abd45fa..000000000000
@@ -1,20 +0,0 @@
-NXP LPC1850 ADC bindings
-
-Required properties:
-- compatible: Should be "nxp,lpc1850-adc"
-- reg: Offset and length of the register set for the ADC device
-- interrupts: The interrupt number for the ADC device
-- clocks: The root clock of the ADC controller
-- vref-supply: The regulator supply ADC reference voltage
-- resets: phandle to reset controller and line specifier
-
-Example:
-
-adc0: adc@400e3000 {
-	compatible = "nxp,lpc1850-adc";
-	reg = <0x400e3000 0x1000>;
-	interrupts = <17>;
-	clocks = <&ccu1 CLK_APB3_ADC0>;
-	vref-supply = <&reg_vdda>;
-	resets = <&rgu 40>;
-};

61 lines not on this page · raw message

deleted file mode 100644
index 3a1bc669bd51..000000000000
@@ -1,21 +0,0 @@
-* NXP LPC32xx SoC ADC controller
-
-Required properties:
-- compatible: must be "nxp,lpc3220-adc"
-- reg: physical base address of the controller and length of memory mapped
-  region.
-- interrupts: The ADC interrupt
-
-Optional:
- - vref-supply: The regulator supply ADC reference voltage, optional
-   for legacy reason, but highly encouraging to us in new device tree
-
-Example:
-
-	adc@40048000 {
-		compatible = "nxp,lpc3220-adc";
-		reg = <0x40048000 0x1000>;
-		interrupt-parent = <&mic>;
-		interrupts = <39 0>;
-		vref-supply = <&vcc>;
-	};

50 lines not on this page · raw message

deleted file mode 100644
index ec04008e8f4f..000000000000
@@ -1,17 +0,0 @@
-Motorola CPCAP PMIC ADC binding
-
-Required properties:
-- compatible: Should be "motorola,cpcap-adc" or "motorola,mapphone-cpcap-adc"
-- interrupts: The interrupt number for the ADC device
-- interrupt-names: Should be "adcdone"
-- #io-channel-cells: Number of cells in an IIO specifier
-
-Example:
-
-cpcap_adc: adc {
-	compatible = "motorola,mapphone-cpcap-adc";
-	interrupt-parent = <&cpcap>;
-	interrupts = <8 IRQ_TYPE_NONE>;
-	interrupt-names = "adcdone";
-	#io-channel-cells = <1>;
-};

51 lines not on this page · raw message

deleted file mode 100644
index c07228da92ac..000000000000
@@ -1,16 +0,0 @@
-Dialog Semiconductor DA9150 IIO GPADC bindings
-
-Required properties:
-- compatible: "dlg,da9150-gpadc" for DA9150 IIO GPADC
-- #io-channel-cells: Should be set to <1>
-  (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info)
-
-For further information on GPADC channels, see device datasheet.
-
-
-Example:
-
-	gpadc: da9150-gpadc {
-		compatible = "dlg,da9150-gpadc";
-		#io-channel-cells = <1>;
-	};

new file mode 100644
index 000000000000..15c51d337108
@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/dlg,da9150-gpadc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Dialog Semiconductor DA9150 IIO GPADC
+
+maintainers:
+  - Adam Thomson <[email protected]>
+
+description:
+  This patch adds support for general purpose ADC within the
+  DA9150 Charger & Fuel-Gauge IC.
+
+properties:
+  compatible:
+    const: dlg,da9150-gpadc
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - "#io-channel-cells"
+
+examples:
+  - |
+    adc {
+        compatible = "dlg,da9150-gpadc";
+        #io-channel-cells = <1>;
+    };
+...

deleted file mode 100644
index 904f76de9055..000000000000
@@ -1,22 +0,0 @@
-* Cosmic Circuits - Analog to Digital Converter (CC-10001-ADC)
-
-Required properties:
-  - compatible: Should be "cosmic,10001-adc"
-  - reg: Should contain adc registers location and length.
-  - clock-names: Should contain "adc".
-  - clocks: Should contain a clock specifier for each entry in clock-names
-  - vref-supply: The regulator supply ADC reference voltage.
-
-Optional properties:
-  - adc-reserved-channels: Bitmask of reserved channels,
-    i.e. channels that cannot be used by the OS.
-
-Example:
-adc: adc@18101600 {
-	compatible = "cosmic,10001-adc";
-	reg = <0x18101600 0x24>;
-	adc-reserved-channels = <0x2>;
-	clocks = <&adc_clk>;
-	clock-names = "adc";
-	vref-supply = <&reg_1v8>;
-};

59 lines not on this page · raw message

deleted file mode 100644
index c7f5057356b1..000000000000
@@ -1,16 +0,0 @@
-* Analog Devices AD7949/AD7682/AD7689
-
-Required properties:
- - compatible: Should be one of
-	* "adi,ad7949"
-	* "adi,ad7682"
-	* "adi,ad7689"
- - reg: spi chip select number for the device
- - vref-supply: The regulator supply for ADC reference voltage
-
-Example:
-adc@0 {
-	compatible = "adi,ad7949";
-	reg = <0>;
-	vref-supply = <&vdd_supply>;
-};

57 lines not on this page · raw message

deleted file mode 100644
index 9f5b88cf680d..000000000000
@@ -1,41 +0,0 @@
-Analog Devices AD7768-1 ADC device driver
-
-Required properties for the AD7768-1:
-
-- compatible: Must be "adi,ad7768-1"
-- reg: SPI chip select number for the device
-- spi-max-frequency: Max SPI frequency to use
-	see: Documentation/devicetree/bindings/spi/spi-bus.txt
-- clocks: phandle to the master clock (mclk)
-	see: Documentation/devicetree/bindings/clock/clock-bindings.txt
-- clock-names: Must be "mclk".
-- interrupts: IRQ line for the ADC
-	see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-- vref-supply: vref supply can be used as reference for conversion
-- adi,sync-in-gpios: must be the device tree identifier of the SYNC-IN pin. Enables
-	synchronization of multiple devices that require simultaneous sampling.
-	A pulse is always required if the configuration is changed in any way, for example
-	if the filter decimation rate changes. As the line is active low, it should
-	be marked GPIO_ACTIVE_LOW.
-
-Optional properties:
-
- - reset-gpios : GPIO spec for the RESET pin. If specified, it will be asserted during
-	driver probe. As the line is active low, it should be marked GPIO_ACTIVE_LOW.
-
-Example:
-
-	adc@0 {
-		compatible = "adi,ad7768-1";
-		reg = <0>;
-		spi-max-frequency = <2000000>;
-		spi-cpol;
-		spi-cpha;
-		vref-supply = <&adc_vref>;
-		interrupts = <25 IRQ_TYPE_EDGE_RISING>;
-		interrupt-parent = <&gpio>;
-		adi,sync-in-gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
-		reset-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
-		clocks = <&ad7768_mclk>;
-		clock-names = "mclk";
-	};

89 lines not on this page · raw message

deleted file mode 100644
index 918a507d1159..000000000000
@@ -1,73 +0,0 @@
-ADS1015 (I2C)
-
-This device is a 12-bit A-D converter with 4 inputs.
-
-The inputs can be used single ended or in certain differential combinations.
-
-For configuration all possible combinations are mapped to 8 channels:
-  0: Voltage over AIN0 and AIN1.
-  1: Voltage over AIN0 and AIN3.
-  2: Voltage over AIN1 and AIN3.
-  3: Voltage over AIN2 and AIN3.
-  4: Voltage over AIN0 and GND.
-  5: Voltage over AIN1 and GND.
-  6: Voltage over AIN2 and GND.
-  7: Voltage over AIN3 and GND.
-
-Each channel can be configured individually:
- - pga is the programmable gain amplifier (values are full scale)
-    0: +/- 6.144 V
-    1: +/- 4.096 V
-    2: +/- 2.048 V (default)
-    3: +/- 1.024 V
-    4: +/- 0.512 V
-    5: +/- 0.256 V
- - data_rate in samples per second
-    0: 128
-    1: 250
-    2: 490
-    3: 920
-    4: 1600 (default)
-    5: 2400
-    6: 3300
-
-1) The /ads1015 node
-
-  Required properties:
-
-   - compatible : must be "ti,ads1015"
-   - reg : I2C bus address of the device
-   - #address-cells : must be <1>
-   - #size-cells : must be <0>
-
-  The node contains child nodes for each channel that the platform uses.
-
-  Example ADS1015 node:
-
-    ads1015@49 {
-	    compatible = "ti,ads1015";
-	    reg = <0x49>;
-	    #address-cells = <1>;
-	    #size-cells = <0>;
-
-	    [ child node definitions... ]
-    }
-
-2) channel nodes
-
-  Required properties:
-
-   - reg : the channel number
-
-  Optional properties:
-
-   - ti,gain : the programmable gain amplifier setting
-   - ti,datarate : the converter data rate
-
-  Example ADS1015 channel node:
-
-    channel@4 {
-	    reg = <4>;
-	    ti,gain = <3>;
-	    ti,datarate = <5>;
-    };

113 lines not on this page · raw message

deleted file mode 100644
index 3b0348c5e516..000000000000
@@ -1,21 +0,0 @@
-Holt Integrated Circuits HI-8435 threshold detector bindings
-
-Required properties:
- - compatible: should be "holt,hi8435"
- - reg: spi chip select number for the device
-
-Recommended properties:
- - spi-max-frequency: definition as per
-		Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Optional properties:
- - gpios: GPIO used for controlling the reset pin
-
-Example:
-sensor@0 {
-	compatible = "holt,hi8435";
-	reg = <0>;
-	gpios = <&gpio6 1 0>;
-
-	spi-max-frequency = <1000000>;
-};

49 lines not on this page · raw message

deleted file mode 100644
index d57e9df25f4f..000000000000
@@ -1,48 +0,0 @@
-* Amlogic Meson SAR (Successive Approximation Register) A/D converter
-
-Required properties:
-- compatible:	depending on the SoC this should be one of:
-			- "amlogic,meson8-saradc" for Meson8
-			- "amlogic,meson8b-saradc" for Meson8b
-			- "amlogic,meson8m2-saradc" for Meson8m2
-			- "amlogic,meson-gxbb-saradc" for GXBB
-			- "amlogic,meson-gxl-saradc" for GXL
-			- "amlogic,meson-gxm-saradc" for GXM
-			- "amlogic,meson-axg-saradc" for AXG
-			- "amlogic,meson-g12a-saradc" for AXG
-		along with the generic "amlogic,meson-saradc"
-- reg:		the physical base address and length of the registers
-- interrupts:	the interrupt indicating end of sampling
-- clocks:	phandle and clock identifier (see clock-names)
-- clock-names:	mandatory clocks:
-			- "clkin" for the reference clock (typically XTAL)
-			- "core" for the SAR ADC core clock
-		optional clocks:
-			- "adc_clk" for the ADC (sampling) clock
-			- "adc_sel" for the ADC (sampling) clock mux
-- vref-supply:	the regulator supply for the ADC reference voltage
-- #io-channel-cells: must be 1, see ../iio-bindings.txt
-
-Optional properties:
-- amlogic,hhi-sysctrl:	phandle to the syscon which contains the 5th bit
-			of the TSC (temperature sensor coefficient) on
-			Meson8b and Meson8m2 (which used to calibrate the
-			temperature sensor)
-- nvmem-cells:		phandle to the temperature_calib eFuse cells
-- nvmem-cell-names:	if present (to enable the temperature sensor
-			calibration) this must contain "temperature_calib"
-
-
-Example:
-	saradc: adc@8680 {
-		compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
-		#io-channel-cells = <1>;
-		reg = <0x0 0x8680 0x0 0x34>;
-		interrupts = <GIC_SPI 73 IRQ_TYPE_EDGE_RISING>;
-		clocks = <&xtal>,
-			 <&clkc CLKID_SAR_ADC>,
-			 <&clkc CLKID_SANA>,
-			 <&clkc CLKID_SAR_ADC_CLK>,
-			 <&clkc CLKID_SAR_ADC_SEL>;
-		clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
-	};

145 lines not on this page · raw message

new file mode 100644
index 000000000000..dc5eacb38046
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/fsl,imx7d-adc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale ADC found on the imx7d SoC
+
+maintainers:
+  - Haibo Chen <[email protected]>
+
+properties:
+  compatible:
+    const: fsl,imx7d-adc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: adc
+
+  vref-supply: true
+
+  "#io-channel-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - vref-supply
+  - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/clock/imx7d-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    soc {
+        #address-cells = <1>;
+        #size-cells = <1>;
+        adc@30610000 {
+            compatible = "fsl,imx7d-adc";
+            reg = <0x30610000 0x10000>;
+            interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+            clock-names = "adc";
+            vref-supply = <&reg_vcc_3v3_mcu>;
+            #io-channel-cells = <1>;
+        };
+    };
+...

deleted file mode 100644
index f1f3a552459b..000000000000
@@ -1,24 +0,0 @@
-Freescale imx7d ADC bindings
-
-The devicetree bindings are for the ADC driver written for
-imx7d SoC.
-
-Required properties:
-- compatible: Should be "fsl,imx7d-adc"
-- reg: Offset and length of the register set for the ADC device
-- interrupts: The interrupt number for the ADC device
-- clocks: The root clock of the ADC controller
-- clock-names: Must contain "adc", matching entry in the clocks property
-- vref-supply: The regulator supply ADC reference voltage
-- #io-channel-cells: Must be 1 as per ../iio-bindings.txt
-
-Example:
-adc1: adc@30610000 {
-	compatible = "fsl,imx7d-adc";
-	reg = <0x30610000 0x10000>;
-	interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-	clocks = <&clks IMX7D_ADC_ROOT_CLK>;
-	clock-names = "adc";
-	vref-supply = <&reg_vcc_3v3_mcu>;
-	#io-channel-cells = <1>;
-};

deleted file mode 100644
index eebdcec3dab5..000000000000
@@ -1,57 +0,0 @@
-Freescale i.MX25 ADC GCQ device
-
-This is a generic conversion queue device that can convert any of the
-analog inputs using the ADC unit of the i.MX25.
-
-Required properties:
- - compatible: Should be "fsl,imx25-gcq".
- - reg: Should be the register range of the module.
- - interrupts: Should be the interrupt number of the module.
-   Typically this is <1>.
- - #address-cells: Should be <1> (setting for the subnodes)
- - #size-cells: Should be <0> (setting for the subnodes)
-
-Optional properties:
- - vref-ext-supply: The regulator supplying the ADC reference voltage.
-   Required when at least one subnode uses the this reference.
- - vref-xp-supply: The regulator supplying the ADC reference voltage on pin XP.
-   Required when at least one subnode uses this reference.
- - vref-yp-supply: The regulator supplying the ADC reference voltage on pin YP.
-   Required when at least one subnode uses this reference.
-
-Sub-nodes:
-Optionally you can define subnodes which define the reference voltage
-for the analog inputs.
-
-Required properties for subnodes:
- - reg: Should be the number of the analog input.
-     0: xp
-     1: yp
-     2: xn
-     3: yn
-     4: wiper
-     5: inaux0
-     6: inaux1
-     7: inaux2
-Optional properties for subnodes:
- - fsl,adc-refp: specifies the positive reference input as defined in
-     <dt-bindings/iio/adc/fsl-imx25-gcq.h>
- - fsl,adc-refn: specifies the negative reference input as defined in
-     <dt-bindings/iio/adc/fsl-imx25-gcq.h>
-
-Example:
-
-	adc: adc@50030800 {
-		compatible = "fsl,imx25-gcq";
-		reg = <0x50030800 0x60>;
-		interrupt-parent = <&tscadc>;
-		interrupts = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		inaux@5 {
-			reg = <5>;
-			fsl,adc-refp = <MX25_ADC_REFP_INT>;
-			fsl,adc-refn = <MX25_ADC_REFN_NGND>;
-		};
-	};

129 lines not on this page · raw message