Skip to contentSkip to conversation

PCIe hot-plug issue: Failed to check link status

DISCUSSION Myron Stowe 2 participants 3 messages Sep 8, 2020 – Sep 14, 2020 PCI

lore
Share & tools
lore
#0 lore raw

On a system with a Mellanox Technologies MT27800 Family [ConnectX-5] NIC controller containing a power button, hot-plug fails to function properly.

Normal, expected, scenario:
o Press the OCP NIC's power button;
o Power button LED blinks and turns off (delivering event message to CPU);
o Verify NIC is offline via 'lspci';
o Remove controller.

Scenario with cmdline parameter 'pcie_port_pm=off':
o Press NIC's power button;
o LED turns off;
o Verify NIC is offline;
o Press power button (in an attempt to hot-add controller);
o NIC is not recognized.

Scenario with no cmdline parameter, or ''pcie_aspm=off', or 'pcie_aspm=off pcie_port_pm=off':
o Press NIC's power button;
o LED continuously flashes;
o Checking via 'lspci' indicates NIC is offline but with LED flashing, the controller can not be removed.

The 'dmesg', and 'lspci', logs are included within the associated bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=209113

As stated in the bugzilla, I'm relaying all this information second hand. Hoping to get the affected party involved directly.

#1 lore raw
Quoted 3 lines · Myron Stowe

On a system with a Mellanox Technologies MT27800 Family [ConnectX-5] NIC controller containing a power button, hot-plug fails to function properly.

[...]

Quoted 1 line

https://bugzilla.kernel.org/show_bug.cgi?id=209113

Thanks for the report.

So in the dmesg output you've provided, the card is already inserted when the machine boots. At 233 seconds, the Attention Button is pressed twice within 200 msec (the second press cancels the first). At 235 sec, the button is pressed again and after 5 sec the slot is brought down. So far so good.

At 291 sec the button is pressed but bringup of the slot fails. What happens here is, pciehp notices that upon the button press, a card is already present in the slot. So for convenience, instead of waiting the full 5 sec, it attempts to bring up the slot immediately. That fails because Data Link Layer Link Active isn't set within 1 sec.

The difference to v4.18 is that back then, pciehp waited the full 5 sec before bringing up the slot.

Per PCIe r4.0 sec 6.7.1.8:

After turning power on, software must wait for a Data Link Layer State Changed event, as described in Section 6.7.3.3.

And per sec 6.7.3.3:

The Data Link Layer State Changed event must occur within 1 second of the event that initiates the hot-insertion. If a power controller is supported, the time out interval is measured from when software initiated a write to the Slot Control register to turn on the power. [...] Software is allowed to time out on a hot add operation if the Data Link Layer State Changed event does not occur within 1 second.

So we adhere to the spec regarding the timeout between enabling power and waiting for DLLLA. We do not exactly adhere to the spec regarding the 5 sec delay between button press and acting on it. But I can't really imagine that's the problem.

As a shot in the dark, could you amend pcie_wait_for_link_delay() in drivers/pci/pci.c and increase the "timeout = 1000" a little? Maybe more than 1 sec is necessary in this case between enabling power and timing out for lack of a link?

The v4.18 output you've provided in the bugzilla is incomplete and lacks time stamps. Could you provide it in full?

Thanks,

Lukas

#2 lore raw
Quoted 45 lines · On Thu, 10 Sep 2020 15:24:40 +0200 Lukas Wunner <[email protected]> wrote:
Quoted 3 lines · Myron Stowe

On a system with a Mellanox Technologies MT27800 Family [ConnectX-5] NIC controller containing a power button, hot-plug fails to function properly.

[...]

Quoted 1 line

https://bugzilla.kernel.org/show_bug.cgi?id=209113

Thanks for the report.

So in the dmesg output you've provided, the card is already inserted when the machine boots. At 233 seconds, the Attention Button is pressed twice within 200 msec (the second press cancels the first). At 235 sec, the button is pressed again and after 5 sec the slot is brought down. So far so good.

At 291 sec the button is pressed but bringup of the slot fails. What happens here is, pciehp notices that upon the button press, a card is already present in the slot. So for convenience, instead of waiting the full 5 sec, it attempts to bring up the slot immediately. That fails because Data Link Layer Link Active isn't set within 1 sec.

The difference to v4.18 is that back then, pciehp waited the full 5 sec before bringing up the slot.

Per PCIe r4.0 sec 6.7.1.8:

After turning power on, software must wait for a Data Link Layer State Changed event, as described in Section 6.7.3.3.

And per sec 6.7.3.3:

The Data Link Layer State Changed event must occur within 1 second of the event that initiates the hot-insertion. If a power
controller is supported, the time out interval is measured from when software initiated a write to the Slot Control register to turn on the power. [...] Software is allowed to time out on a hot add operation if the Data Link Layer State Changed event does not occur within 1 second.

So we adhere to the spec regarding the timeout between enabling power and waiting for DLLLA. We do not exactly adhere to the spec regarding the 5 sec delay between button press and acting on it. But I can't really imagine that's the problem.

Quoted 7 lines

As a shot in the dark, could you amend pcie_wait_for_link_delay() in drivers/pci/pci.c and increase the "timeout = 1000" a little? Maybe more than 1 sec is necessary in this case between enabling power and timing out for lack of a link?

The v4.18 output you've provided in the bugzilla is incomplete and lacks time stamps. Could you provide it in full?

Hi Lukas,

I got back a full 'dmesg' log, with the hot-plug event included, from the earlier, working scenario, kernel. It's attached to the BZ as "dmesg log of v3.10+ showing successful hot-plug event". Note the v3.10 basis as I was incorrect before in thinking the working case was from a v4.18 basis. For this case, the hot-plug event starts 113 seconds in.

As for your "shot in the dark", the reporters doubled the timeout value in pcie_wait_for_link_delay() and had positive results. The 'dmesg' log from that testing is also attached to the BZ as "dmesg log of v5.8.8 with increased timeout". So it looks as if this specific controller is not adhering to the Data Link Layer State Changed event within the specified time.

There was an earlier attachment of a couple of 'dmesg' logs that you can ignore (i.e., dmesg with timestamp for RHEL...).

Myron

Quoted 5 lines

Thanks,

Lukas