mmc: xenon_sdhci: Add missing common host capabilities
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Use mmc_of_parse() to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.
But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
---
Tested myself on v5 without emmc, mmc info is unchanged for my sd card
Tested by G?rald on v7 emmc, which started working with this patch:
=> mmc info
Device: sdhci at d8000
Manufacturer ID: 45
OEM: 100
Name: SEM04
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Erase Group Size: 256 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.7 GiB WRREL
Boot Capacity: 2 MiB
RPMB Capacity: 2 MiB
Boot area 0 is not write protected
Boot area 1 is not write protected
drivers/mmc/xenon_sdhci.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)
drivers/mmc/xenon_sdhci.c +4 -14
@@ -485,20 +485,10 @@ static int xenon_sdhci_probe(struct udevice *dev)armada_3700_soc_pad_voltage_set (host); host->host_caps =MMC_MODE_HS | MMC_MODE_HS_52MHz | MMC_MODE_DDR_52MHz; -switch (fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev),"bus-width" , -1 )) { -case 8 : - host->host_caps |=MMC_MODE_8BIT ; -break ; -case 4 : - host->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -printf ("Invalid \"bus-width\" value\n" ); -return -EINVAL ; - } + + ret =mmc_of_parse (dev, &plat->cfg); +if (ret) +return ret; host->ops = &xenon_sdhci_ops;
Signature · 1 line
2.28.0
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Quoted 13 lines
-----Original Message-----
From: Andre Heider <[email protected]>
Sent: Thursday, September 10, 2020 20:54
To: Stefan Roese <[email protected]>; Kostya Porotchkin <[email protected]>
Cc: Pali Roh?r <[email protected]>; G?rald Kerma <[email protected]>; u- boot at lists.denx.de
Subject: [EXT] [PATCH] mmc:xenon_sdhci: Add missing common host capabilitiesExternal Email
Quoted 8 lines
----------------------------------------------------------------------
Usemmc_of_parse()to set the common host properties. That includes "bus- width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>
Quoted 61 lines
---
Tested myself on v5 without emmc,
mmc infois unchanged for my sd cardTested by G?rald on v7 emmc, which started working with this patch:
=> mmc info
Device: sdhci at d8000
Manufacturer ID: 45
OEM: 100
Name: SEM04
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Erase Group Size: 256 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.7 GiB WRREL
Boot Capacity: 2 MiB
RPMB Capacity: 2 MiB
Boot area 0 is not write protected
Boot area 1 is not write protecteddrivers/mmc/xenon_sdhci.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)drivers/mmc/xenon_sdhci.c index renamed from drivers/mmc/xenon_sdhci.c +0
-0
7f9a579c83..6ce9d00d0a100644drivers/mmc/xenon_sdhci.c +4
-14@@ -485,20 +485,10 @@ static int xenon_sdhci_probe(struct udevice *dev)armada_3700_soc_pad_voltage_set (host); host->host_caps =MMC_MODE_HS | MMC_MODE_HS_52MHz | MMC_MODE_DDR_52MHz; -switch (fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev),"bus- width", -1 )) { -case 8 : - host->host_caps |=MMC_MODE_8BIT ; -break ; -case 4 : - host->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -printf ("Invalid \"bus-width\" value\n" ); -return -EINVAL ; - } + + ret =mmc_of_parse (dev, &plat->cfg); +if (ret) +return ret;
host->ops=&xenon_sdhci_ops;--
2.28.0
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
In reply to Andre HeiderQuoted 8 lines · On Thursday 10 September 2020 19:53:40 Andre Heider wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Adding Marek to loop, can you test this patch on MOX A to verify that it does not break MOX uSD and SDIO support?
(PS: Andre, for one week I would not be available, therefore in this time I would not be able to test or review Armada 3720 patches...)
Quoted 59 lines
Tested myself on v5 without emmc,
mmc infois unchanged for my sd cardTested by G?rald on v7 emmc, which started working with this patch:
=> mmc info
Device: sdhci at d8000
Manufacturer ID: 45
OEM: 100
Name: SEM04
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Erase Group Size: 256 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.7 GiB WRREL
Boot Capacity: 2 MiB
RPMB Capacity: 2 MiB
Boot area 0 is not write protected
Boot area 1 is not write protecteddrivers/mmc/xenon_sdhci.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)drivers/mmc/xenon_sdhci.c +4
-14@@ -485,20 +485,10 @@ static int xenon_sdhci_probe(struct udevice *dev)armada_3700_soc_pad_voltage_set (host); host->host_caps =MMC_MODE_HS | MMC_MODE_HS_52MHz | MMC_MODE_DDR_52MHz; -switch (fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev),"bus-width" , -1 )) { -case 8 : - host->host_caps |=MMC_MODE_8BIT ; -break ; -case 4 : - host->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -printf ("Invalid \"bus-width\" value\n" ); -return -EINVAL ; - } + + ret =mmc_of_parse (dev, &plat->cfg); +if (ret) +return ret; host->ops = &xenon_sdhci_ops;Signature · 1 line
2.28.0
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Hi Pali, Andre and others,
Quoted 7 lines · Pali Roh?r
Quoted 6 lines · On Thursday 10 September 2020 19:53:40 Andre Heider wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Quoted 8 lines
Quoted 2 lines
Signed-off-by Andre Heider <[email protected]>---
Adding Marek to loop, can you test this patch on MOX A to verify that it does not break MOX uSD and SDIO support?
(PS: Andre, for one week I would not be available, therefore in this time I would not be able to test or review Armada 3720 patches...)
I'll also be on vacation next week. Sorry, I was not able to follow all discussions on these Armada related patches lately. Could someone please summarize, which patches (fixes) are "okay" for merging in this rc stage (rc4)? That would really be helpful.
Thanks,
Stefan
Quoted 54 lines
Quoted 54 lines
Tested myself on v5 without emmc,
mmc infois unchanged for my sd cardTested by G?rald on v7 emmc, which started working with this patch:
=> mmc info
Device: sdhci at d8000
Manufacturer ID: 45
OEM: 100
Name: SEM04
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Erase Group Size: 256 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.7 GiB WRREL
Boot Capacity: 2 MiB
RPMB Capacity: 2 MiB
Boot area 0 is not write protected
Boot area 1 is not write protecteddrivers/mmc/xenon_sdhci.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)drivers/mmc/xenon_sdhci.c +4
-14@@ -485,20 +485,10 @@ static int xenon_sdhci_probe(struct udevice *dev)armada_3700_soc_pad_voltage_set (host); host->host_caps =MMC_MODE_HS | MMC_MODE_HS_52MHz | MMC_MODE_DDR_52MHz; -switch (fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev),"bus-width" , -1 )) { -case 8 : - host->host_caps |=MMC_MODE_8BIT ; -break ; -case 4 : - host->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -printf ("Invalid \"bus-width\" value\n" ); -return -EINVAL ; - } + + ret =mmc_of_parse (dev, &plat->cfg); +if (ret) +return ret;
Quoted 5 lines
Quoted 5 lines
drivers/mmc/xenon_sdhci.c +0
-0host->ops = &xenon_sdhci_ops;Signature · 1 line
2.28.0
Viele Gr??e,
Stefan
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Quoted 16 lines · Stefan Roese
Hi Pali, Andre and others,
Quoted 13 lines · Pali Roh?r
Quoted 8 lines · On Thursday 10 September 2020 19:53:40 Andre Heider wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Adding Marek to loop, can you test this patch on MOX A to verify that it does not break MOX uSD and SDIO support?
Quoted 7 lines
Quoted 2 lines
(PS: Andre, for one week I would not be available, therefore in this time I would not be able to test or review Armada 3720 patches...)
I'll also be on vacation next week. Sorry, I was not able to follow all discussions on these Armada related patches lately. Could someone please summarize, which patches (fixes) are "okay" for merging in this rc stage (rc4)? That would really be helpful.
Going by patchwork we have:
All superseded:
https://patchwork.ozlabs.org/project/uboot/list/?series=198544
https://patchwork.ozlabs.org/project/uboot/list/?series=198545
https://patchwork.ozlabs.org/project/uboot/list/?series=198756
https://patchwork.ozlabs.org/project/uboot/list/?series=199690
From my point of view these can go in:
This one, fix emmc:
https://patchwork.ozlabs.org/project/uboot/list/?series=200919
dts: fix vendor, add -emmc variant:
https://patchwork.ozlabs.org/project/uboot/list/?series=199579
These two for uDPU from its maintainer, taken from the OpenWRT uboot-mvebu package:CONFIG_SYS_BOOTM_LEN to 64MB:
https://patchwork.ozlabs.org/project/uboot/list/?series=199858
add support for Macronix mx25u12835f flash:
https://patchwork.ozlabs.org/project/uboot/list/?series=199857
And I'd take these two too, Pali has different opinion though:
enable NET_RANDOM_ETHADDR:
https://patchwork.ozlabs.org/project/uboot/list/?series=200115
set fdtfile:
https://patchwork.ozlabs.org/project/uboot/list/?series=201051
Thanks,
Andre
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Quoted 35 lines · On Fri, 11 Sep 2020 10:37:42 +0200 Andre Heider <[email protected]> wrote:
Quoted 17 lines · Stefan Roese
Hi Pali, Andre and others,
Quoted 14 lines · Pali Roh?r
Quoted 9 lines · On Thursday 10 September 2020 19:53:40 Andre Heider wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Adding Marek to loop, can you test this patch on MOX A to verify that it does not break MOX uSD and SDIO support?
Quoted 8 lines
Quoted 3 lines
(PS: Andre, for one week I would not be available, therefore in this time I would not be able to test or review Armada 3720 patches...)
I'll also be on vacation next week. Sorry, I was not able to follow all discussions on these Armada related patches lately. Could someone please summarize, which patches (fixes) are "okay" for merging in this rc stage (rc4)? That would really be helpful.
Going by patchwork we have:
All superseded:
https://patchwork.ozlabs.org/project/uboot/list/?series=198544
https://patchwork.ozlabs.org/project/uboot/list/?series=198545
https://patchwork.ozlabs.org/project/uboot/list/?series=198756
https://patchwork.ozlabs.org/project/uboot/list/?series=199690
Quoted 4 lines
From my point of view these can go in:
This one, fix emmc:
https://patchwork.ozlabs.org/project/uboot/list/?series=200919
I shall check this if it does not break our boards.
Quoted 10 lines
dts: fix vendor, add -emmc variant:
https://patchwork.ozlabs.org/project/uboot/list/?series=199579These two for uDPU from its maintainer, taken from the OpenWRT uboot-mvebu package:
CONFIG_SYS_BOOTM_LENto 64MB:
https://patchwork.ozlabs.org/project/uboot/list/?series=199858
add support for Macronix mx25u12835f flash:
https://patchwork.ozlabs.org/project/uboot/list/?series=199857
Quoted 5 lines
And I'd take these two too, Pali has different opinion though:
enableNET_RANDOM_ETHADDR:
https://patchwork.ozlabs.org/project/uboot/list/?series=200115
set fdtfile:
https://patchwork.ozlabs.org/project/uboot/list/?series=201051
I have replied to the NET_RANDOM_ETHADDR patch, please comment on my reply.
As for the fdtfile I think it is good to go.
Quoted 2 lines
Thanks,
Andre
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Quoted 61 lines · Marek Beh?n
Quoted 35 lines · On Fri, 11 Sep 2020 10:37:42 +0200 Andre Heider <[email protected]> wrote:
Quoted 17 lines · Stefan Roese
Hi Pali, Andre and others,
Quoted 14 lines · Pali Roh?r
Quoted 9 lines · On Thursday 10 September 2020 19:53:40 Andre Heider wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Adding Marek to loop, can you test this patch on MOX A to verify that it does not break MOX uSD and SDIO support?
Quoted 8 lines
Quoted 3 lines
(PS: Andre, for one week I would not be available, therefore in this time I would not be able to test or review Armada 3720 patches...)
I'll also be on vacation next week. Sorry, I was not able to follow all discussions on these Armada related patches lately. Could someone please summarize, which patches (fixes) are "okay" for merging in this rc stage (rc4)? That would really be helpful.
Going by patchwork we have:
All superseded:
https://patchwork.ozlabs.org/project/uboot/list/?series=198544
https://patchwork.ozlabs.org/project/uboot/list/?series=198545
https://patchwork.ozlabs.org/project/uboot/list/?series=198756
https://patchwork.ozlabs.org/project/uboot/list/?series=199690Quoted 4 lines
From my point of view these can go in:
This one, fix emmc:
https://patchwork.ozlabs.org/project/uboot/list/?series=200919I shall check this if it does not break our boards.
Quoted 10 lines
dts: fix vendor, add -emmc variant:
https://patchwork.ozlabs.org/project/uboot/list/?series=199579These two for uDPU from its maintainer, taken from the OpenWRT uboot-mvebu package:
CONFIG_SYS_BOOTM_LENto 64MB:
https://patchwork.ozlabs.org/project/uboot/list/?series=199858
add support for Macronix mx25u12835f flash:
https://patchwork.ozlabs.org/project/uboot/list/?series=199857Quoted 5 lines
And I'd take these two too, Pali has different opinion though:
enableNET_RANDOM_ETHADDR:
https://patchwork.ozlabs.org/project/uboot/list/?series=200115
set fdtfile:
https://patchwork.ozlabs.org/project/uboot/list/?series=201051
Quoted 4 lines
I have replied to the
NET_RANDOM_ETHADDRpatch, please comment on my reply.As for the fdtfile I think it is good to go.
Thanks. Unfortunately this is taking a bit too long for me, as I have to leave in about an hour. I will take care of these patches in a bit over a week.
Thanks,
Stefan
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Quoted 6 lines · On Fri, 11 Sep 2020 14:21:46 +0200 Stefan Roese <[email protected]> wrote:
Thanks. Unfortunately this is taking a bit too long for me, as I have to leave in about an hour. I will take care of these patches in a bit over a week.
Thanks,
Stefan
Happy vacation, Stefan :)
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
In reply to Andre HeiderQuoted 65 lines · On Thu, 10 Sep 2020 19:53:40 +0200 Andre Heider <[email protected]> wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Tested myself on v5 without emmc,
mmc infois unchanged for my sd cardTested by G?rald on v7 emmc, which started working with this patch:
=> mmc info
Device: sdhci at d8000
Manufacturer ID: 45
OEM: 100
Name: SEM04
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Erase Group Size: 256 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.7 GiB WRREL
Boot Capacity: 2 MiB
RPMB Capacity: 2 MiB
Boot area 0 is not write protected
Boot area 1 is not write protecteddrivers/mmc/xenon_sdhci.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)drivers/mmc/xenon_sdhci.c +4
-14@@ -485,20 +485,10 @@ static int xenon_sdhci_probe(struct udevice *dev) armada_3700_soc_pad_voltage_set(host); host->host_caps =MMC_MODE_HS | MMC_MODE_HS_52MHz | MMC_MODE_DDR_52MHz; -switch (fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev),"bus-width" , -1 )) { -case 8 : - host->host_caps |=MMC_MODE_8BIT ; -break ; -case 4 : - host->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -printf ("Invalid \"bus-width\" value\n" ); -return -EINVAL ; - } + + ret =mmc_of_parse (dev, &plat->cfg); +if (ret) +return ret;
Quoted 2 lines
host->ops=&xenon_sdhci_ops;
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
Le 11/09/2020 ? 14:38, Marek Beh?n a ?crit?:
Quoted 68 lines
Quoted 65 lines · On Thu, 10 Sep 2020 19:53:40 +0200 Andre Heider <[email protected]> wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Tested myself on v5 without emmc,
mmc infois unchanged for my sd cardTested by G?rald on v7 emmc, which started working with this patch:
=> mmc info
Device: sdhci at d8000
Manufacturer ID: 45
OEM: 100
Name: SEM04
Bus Speed: 52000000
Mode: MMC High Speed (52MHz)
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 3.7 GiB
Bus Width: 8-bit
Erase Group Size: 256 KiB
HC WP Group Size: 8 MiB
User Capacity: 3.7 GiB WRREL
Boot Capacity: 2 MiB
RPMB Capacity: 2 MiB
Boot area 0 is not write protected
Boot area 1 is not write protecteddrivers/mmc/xenon_sdhci.c | 18 ++++-------------- 1 file changed, 4 insertions(+), 14 deletions(-)drivers/mmc/xenon_sdhci.c +4
-14@@ -485,20 +485,10 @@ static int xenon_sdhci_probe(struct udevice *dev) armada_3700_soc_pad_voltage_set(host); host->host_caps =MMC_MODE_HS | MMC_MODE_HS_52MHz | MMC_MODE_DDR_52MHz; -switch (fdtdec_get_int (gd->fdt_blob,dev_of_offset (dev),"bus-width" , -1 )) { -case 8 : - host->host_caps |=MMC_MODE_8BIT ; -break ; -case 4 : - host->host_caps |=MMC_MODE_4BIT ; -break ; -case 1 : -break ; -default : -printf ("Invalid \"bus-width\" value\n" ); -return -EINVAL ; - } + + ret =mmc_of_parse (dev, &plat->cfg); +if (ret) +return ret;
Quoted 3 lines
Quoted 2 lines
host->ops = &xenon_sdhci_ops;Tested-by Marek Beh?n <[email protected]>
|Tested-by: G?rald Kerma <[email protected]>| ||
PATCH 1/1 mmc: xenon_sdhci: Add missing common host capabilities
In reply to Stefan RoeseQuoted 62 lines · Stefan Roese
Quoted 61 lines · Marek Beh?n
Quoted 35 lines · On Fri, 11 Sep 2020 10:37:42 +0200 Andre Heider <[email protected]> wrote:
Quoted 17 lines · Stefan Roese
Hi Pali, Andre and others,
Quoted 14 lines · Pali Roh?r
Quoted 9 lines · On Thursday 10 September 2020 19:53:40 Andre Heider wrote:
Use
mmc_of_parse()to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver.But more importantly, "non-removable" is now respected, which fixes the usage of eMMC.
Signed-off-by Andre Heider <[email protected]>---
Adding Marek to loop, can you test this patch on MOX A to verify that it does not break MOX uSD and SDIO support?
Quoted 8 lines
Quoted 3 lines
(PS: Andre, for one week I would not be available, therefore in this time I would not be able to test or review Armada 3720 patches...)
I'll also be on vacation next week. Sorry, I was not able to follow all discussions on these Armada related patches lately. Could someone please summarize, which patches (fixes) are "okay" for merging in this rc stage (rc4)? That would really be helpful.
Going by patchwork we have:
All superseded:
https://patchwork.ozlabs.org/project/uboot/list/?series=198544
https://patchwork.ozlabs.org/project/uboot/list/?series=198545
https://patchwork.ozlabs.org/project/uboot/list/?series=198756
https://patchwork.ozlabs.org/project/uboot/list/?series=199690Quoted 4 lines
? From my point of view these can go in:
This one, fix emmc:
https://patchwork.ozlabs.org/project/uboot/list/?series=200919I shall check this if it does not break our boards.
Quoted 15 lines
dts: fix vendor, add -emmc variant:
https://patchwork.ozlabs.org/project/uboot/list/?series=199579These two for uDPU from its maintainer, taken from the OpenWRT uboot-mvebu package:
CONFIG_SYS_BOOTM_LENto 64MB:
https://patchwork.ozlabs.org/project/uboot/list/?series=199858
add support for Macronix mx25u12835f flash:
https://patchwork.ozlabs.org/project/uboot/list/?series=199857And I'd take these two too, Pali has different opinion though:
enableNET_RANDOM_ETHADDR:
https://patchwork.ozlabs.org/project/uboot/list/?series=200115
set fdtfile:
https://patchwork.ozlabs.org/project/uboot/list/?series=201051
Quoted 8 lines
Quoted 4 lines
I have replied to the
NET_RANDOM_ETHADDRpatch, please comment on my reply.As for the fdtfile I think it is good to go.
Thanks. Unfortunately this is taking a bit too long for me, as I have to leave in about an hour. I will take care of these patches in a bit over a week.
Sounds good, thanks!
Have a nice vacation,
Andre