Skip to contentSkip to conversation

ARM: dts: rk3188: correct interrupt flags

PATCH Applied Krzysztof Kozlowski 2 participants 6 messages Sep 17, 2020 – Apr 4, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 ARM: dts: rk3188: correct interrupt flags

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags. These are simple defines so they could be used in DTS but they will not have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags without affecting the code:
ACTIVE_HIGH => IRQ_TYPE_NONE

---

Not tested on HW.

Changes since v1:
1. Correct title

---
 arch/arm/boot/dts/rk3188-bqedison2qc.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/arm/boot/dts/rk3188-bqedison2qc.dts +2 -1
index 66a0ff196eb1..b191347894f6 100644
@@ -7,6 +7,7 @@
 /dts-v1/;
 #include <dt-bindings/i2c/i2c.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3188.dtsi"
 
 / {
@@ -479,7 +480,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio3>;
-		interrupts = <RK_PD2 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PD2 IRQ_TYPE_NONE>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
Signature · 7 lines
2.17.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#1 lore raw

PATCH v2 2/2 arm64: dts: rk3399: correct interrupt flags

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags. These are simple defines so they could be used in DTS but they will not have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted same logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH

---

Not tested on HW.

Changes since v1:
1. Correct title

---
 arch/arm64/boot/dts/rockchip/rk3399-firefly.dts      | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts   | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts    | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts     | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts   | 2 +-
 arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts   | 2 +-
 arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi     | 3 ++-
 8 files changed, 14 insertions(+), 8 deletions(-)
arch/arm64/boot/dts/rockchip/rk3399-firefly.dts +2 -1
index 6db18808b9c5..095d615950ca 100644
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -676,7 +677,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts +2 -1
index 341d074ed996..25cb807bcfa6 100644
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
 
@@ -623,7 +624,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi +2 -1
index e36837c04dc7..89dae74989bb 100644
@@ -6,6 +6,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -662,7 +663,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts +2 -1
index 1fa80ac15464..113a71256171 100644
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -503,7 +504,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts +2 -1
index 6163ae8063a7..ae81fb9d363c 100644
@@ -7,6 +7,7 @@
 
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
 
@@ -691,7 +692,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts +1 -1
index f0055ce2fda0..7df4e698b1c0 100644
@@ -19,7 +19,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts +1 -1
index 4c7ebb1c5d2d..887a29898617 100644
@@ -20,7 +20,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi +2 -1
index 5e3ac589bc54..9a4cd799edde 100644
@@ -7,6 +7,7 @@
 
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	sdio_pwrseq: sdio-pwrseq {
@@ -522,7 +523,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
Signature · 7 lines
2.17.1


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#2 lore raw
In reply to Krzysztof Kozlowski
Quoted 13 lines · Krzysztof Kozlowski

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags. These are simple defines so they could be used in DTS but they will not have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags without affecting the code:
ACTIVE_HIGH => IRQ_TYPE_NONE

---

Quoted 7 lines

Not tested on HW.

Changes since v1:
1. Correct title

---
 arch/arm/boot/dts/rk3188-bqedison2qc.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

Hi,

Any comments/review/testing from Heiko or other Rockchip folks? Shall I cc here someone?

Best regards,
Krzysztof

maintainer
#3 lore raw

Hi,

Am Freitag, 2. Oktober 2020, 18:11:28 CEST schrieb Krzysztof Kozlowski:

Quoted 22 lines · Krzysztof Kozlowski
Quoted 13 lines

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags. These are simple defines so they could be used in DTS but they will not have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags without affecting the code:
ACTIVE_HIGH => IRQ_TYPE_NONE

---

Quoted 7 lines

Not tested on HW.

Changes since v1:
1. Correct title

---
 arch/arm/boot/dts/rk3188-bqedison2qc.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Quoted 4 lines

Hi,

Any comments/review/testing from Heiko or other Rockchip folks? Shall I cc here someone?

I'm actually wondering about this ... I somehow remember writing a response, but don't see it in my history - so it might have gotten lost before I actually sent it.

I think the biggest issue I have is that none of that is tested on any hardware and looking at other brcm wifi drivers in the kernel, the interrupt polarity seems to be all over the place, some set it high, some low and I even have seen edge triggers.

As all changes are in regard to (copied) brcm wifi node, it would be really interesting to actually know what trigger is the right one.

I've Cc'ed Jagan who I think has worked on an affected board, maybe he can check which trigger is correct.

Heiko

#4 lore raw
Quoted 40 lines · Heiko Stübner

Hi,

Am Freitag, 2. Oktober 2020, 18:11:28 CEST schrieb Krzysztof Kozlowski:

Quoted 22 lines · Krzysztof Kozlowski
Quoted 13 lines

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags. These are simple defines so they could be used in DTS but they will not have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags without affecting the code:
ACTIVE_HIGH => IRQ_TYPE_NONE

---

Quoted 7 lines

Not tested on HW.

Changes since v1:
1. Correct title

---
 arch/arm/boot/dts/rk3188-bqedison2qc.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Quoted 4 lines

Hi,

Any comments/review/testing from Heiko or other Rockchip folks? Shall I cc here someone?

I'm actually wondering about this ... I somehow remember writing a response, but don't see it in my history - so it might have gotten lost before I actually sent it.

I think the biggest issue I have is that none of that is tested on any hardware and looking at other brcm wifi drivers in the kernel, the interrupt polarity seems to be all over the place, some set it high, some low and I even have seen edge triggers.

Quoted 5 lines

As all changes are in regard to (copied) brcm wifi node, it would be really interesting to actually know what trigger is the right one.

I've Cc'ed Jagan who I think has worked on an affected board, maybe he can check which trigger is correct.

Hi Heiko,

Nothing moved here since 2020 and the DTSes still have incorrect flags for interrupts.

I can rebase and resend (although maybe it still applies cleanly), but more important - is someone going to take this patch? or test it?

Best regards,
Krzysztof

maintainer Applied
#5 lore raw
In reply to Krzysztof Kozlowski
Quoted 8 lines · Krzysztof Kozlowski

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags. These are simple defines so they could be used in DTS but they will not have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags without affecting the code:
ACTIVE_HIGH => IRQ_TYPE_NONE

Applied, thanks!

[1/2] ARM: dts: rk3188: correct interrupt flags

      commit: 7e5a7e39d767b60d8631792bd3d7820a6f4a43f8
[2/2] arm64: dts: rk3399: correct interrupt flags
      commit: 57f3b0bf5c346f73a848c3d74270b21ed110e530

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>