Skip to contentSkip to conversation

DP83869 WoL and Speed optimization

PATCH RESEND In review Dan Murphy 3 participants 6 messages Sep 28, 2020

Subsystems (3)
lore
Share & tools
lore

Dan Murphy

author
#0 lore raw

v5 cover DP83869 WoL and Speed optimization

Hello

Add the WoL and Speed Optimization (aka downshift) support for the DP83869 Ethernet PHY.

Dan

Dan Murphy (2):
net: phy: dp83869: support Wake on LAN
net: phy: dp83869: Add speed optimization feature

 drivers/net/phy/dp83869.c | 292 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 292 insertions(+)
Signature · 1 line
2.28.0.585.ge1cfff676549
author
#1 lore raw

PATCH RESEND v5 1/2 net: phy: dp83869: support Wake on LAN

This adds WoL support on TI DP83869 for magic, magic secure, unicast and broadcast.

---

v5 - Fixed 0-day warning for u16, removed defconfig

 drivers/net/phy/dp83869.c | 176 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 176 insertions(+)
drivers/net/phy/dp83869.c +176 -0
index 81899bc99add..de68e56faf3d 100644
@@ -4,6 +4,7 @@
  */
 
 #include <linux/ethtool.h>
+#include <linux/etherdevice.h>
 #include <linux/kernel.h>
 #include <linux/mii.h>
 #include <linux/module.h>
@@ -27,6 +28,13 @@
 #define DP83869_RGMIICTL	0x0032
 #define DP83869_STRAP_STS1	0x006e
 #define DP83869_RGMIIDCTL	0x0086
+#define DP83869_RXFCFG		0x0134
+#define DP83869_RXFPMD1		0x0136
+#define DP83869_RXFPMD2		0x0137
+#define DP83869_RXFPMD3		0x0138
+#define DP83869_RXFSOP1		0x0139
+#define DP83869_RXFSOP2		0x013A
+#define DP83869_RXFSOP3		0x013B
 #define DP83869_IO_MUX_CFG	0x0170
 #define DP83869_OP_MODE		0x01df
 #define DP83869_FX_CTRL		0x0c00
@@ -104,6 +112,14 @@
 #define DP83869_OP_MODE_MII			BIT(5)
 #define DP83869_SGMII_RGMII_BRIDGE		BIT(6)
 
+/* RXFCFG bits*/
+#define DP83869_WOL_MAGIC_EN		BIT(0)
+#define DP83869_WOL_PATTERN_EN		BIT(1)
+#define DP83869_WOL_BCAST_EN		BIT(2)
+#define DP83869_WOL_UCAST_EN		BIT(4)
+#define DP83869_WOL_SEC_EN		BIT(5)
+#define DP83869_WOL_ENH_MAC		BIT(7)
+
 enum {
 	DP83869_PORT_MIRRORING_KEEP,
 	DP83869_PORT_MIRRORING_EN,
@@ -177,6 +193,163 @@ static int dp83869_config_intr(struct phy_device *phydev)
 	return phy_write(phydev, MII_DP83869_MICR, micr_status);
 }
 
+static int dp83869_set_wol(struct phy_device *phydev,
+			   struct ethtool_wolinfo *wol)
+{
+	struct net_device *ndev = phydev->attached_dev;
+	int val_rxcfg, val_micr;
+	u8 *mac;
+	int ret;
+
+	val_rxcfg = phy_read_mmd(phydev, DP83869_DEVADDR, DP83869_RXFCFG);
+	if (val_rxcfg < 0)
+		return val_rxcfg;
+
+	val_micr = phy_read(phydev, MII_DP83869_MICR);
+	if (val_micr < 0)
+		return val_micr;
+
+	if (wol->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE | WAKE_UCAST |
+			    WAKE_BCAST)) {
+		val_rxcfg |= DP83869_WOL_ENH_MAC;
+		val_micr |= MII_DP83869_MICR_WOL_INT_EN;
+
+		if (wol->wolopts & WAKE_MAGIC ||
+		    wol->wolopts & WAKE_MAGICSECURE) {
+			mac = (u8 *)ndev->dev_addr;
+
+			if (!is_valid_ether_addr(mac))
+				return -EINVAL;
+
+			ret = phy_write_mmd(phydev, DP83869_DEVADDR,
+					    DP83869_RXFPMD1,
+					    mac[1] << 8 | mac[0]);
+			if (ret)
+				return ret;
+
+			ret = phy_write_mmd(phydev, DP83869_DEVADDR,
+					    DP83869_RXFPMD2,
+					    mac[3] << 8 | mac[2]);
+			if (ret)
+				return ret;
+
+			ret = phy_write_mmd(phydev, DP83869_DEVADDR,
+					    DP83869_RXFPMD3,
+					    mac[5] << 8 | mac[4]);
+			if (ret)
+				return ret;
+
+			val_rxcfg |= DP83869_WOL_MAGIC_EN;
+		} else {
+			val_rxcfg &= ~DP83869_WOL_MAGIC_EN;
+		}
+
+		if (wol->wolopts & WAKE_MAGICSECURE) {
+			ret = phy_write_mmd(phydev, DP83869_DEVADDR,
+					    DP83869_RXFSOP1,
+					    (wol->sopass[1] << 8) | wol->sopass[0]);
+			if (ret)
+				return ret;
+
+			ret = phy_write_mmd(phydev, DP83869_DEVADDR,
+					    DP83869_RXFSOP2,
+					    (wol->sopass[3] << 8) | wol->sopass[2]);
+			if (ret)
+				return ret;
+			ret = phy_write_mmd(phydev, DP83869_DEVADDR,
+					    DP83869_RXFSOP3,
+					    (wol->sopass[5] << 8) | wol->sopass[4]);
+			if (ret)
+				return ret;
+
+			val_rxcfg |= DP83869_WOL_SEC_EN;
+		} else {
+			val_rxcfg &= ~DP83869_WOL_SEC_EN;
+		}
+
+		if (wol->wolopts & WAKE_UCAST)
+			val_rxcfg |= DP83869_WOL_UCAST_EN;
+		else
+			val_rxcfg &= ~DP83869_WOL_UCAST_EN;
+
+		if (wol->wolopts & WAKE_BCAST)
+			val_rxcfg |= DP83869_WOL_BCAST_EN;
+		else
+			val_rxcfg &= ~DP83869_WOL_BCAST_EN;
+	} else {
+		val_rxcfg &= ~DP83869_WOL_ENH_MAC;
+		val_micr &= ~MII_DP83869_MICR_WOL_INT_EN;
+	}
+
+	ret = phy_write_mmd(phydev, DP83869_DEVADDR, DP83869_RXFCFG, val_rxcfg);
+	if (ret)
+		return ret;
+
+	return phy_write(phydev, MII_DP83869_MICR, val_micr);
+}
+
+static void dp83869_get_wol(struct phy_device *phydev,
+			    struct ethtool_wolinfo *wol)
+{
+	u16 value, sopass_val;
+
+	wol->supported = (WAKE_UCAST | WAKE_BCAST | WAKE_MAGIC |
+			WAKE_MAGICSECURE);
+	wol->wolopts = 0;
+
+	value = phy_read_mmd(phydev, DP83869_DEVADDR, DP83869_RXFCFG);
+	if (value < 0) {
+		phydev_err(phydev, "Failed to read RX CFG\n");
+		return;
+	}
+
+	if (value & DP83869_WOL_UCAST_EN)
+		wol->wolopts |= WAKE_UCAST;
+
+	if (value & DP83869_WOL_BCAST_EN)
+		wol->wolopts |= WAKE_BCAST;
+
+	if (value & DP83869_WOL_MAGIC_EN)
+		wol->wolopts |= WAKE_MAGIC;
+
+	if (value & DP83869_WOL_SEC_EN) {
+		sopass_val = phy_read_mmd(phydev, DP83869_DEVADDR,
+					  DP83869_RXFSOP1);
+		if (sopass_val < 0) {
+			phydev_err(phydev, "Failed to read RX SOP 1\n");
+			return;
+		}
+
+		wol->sopass[0] = (sopass_val & 0xff);
+		wol->sopass[1] = (sopass_val >> 8);
+
+		sopass_val = phy_read_mmd(phydev, DP83869_DEVADDR,
+					  DP83869_RXFSOP2);
+		if (sopass_val < 0) {
+			phydev_err(phydev, "Failed to read RX SOP 2\n");
+			return;
+		}
+
+		wol->sopass[2] = (sopass_val & 0xff);
+		wol->sopass[3] = (sopass_val >> 8);
+
+		sopass_val = phy_read_mmd(phydev, DP83869_DEVADDR,
+					  DP83869_RXFSOP3);
+		if (sopass_val < 0) {
+			phydev_err(phydev, "Failed to read RX SOP 3\n");
+			return;
+		}
+
+		wol->sopass[4] = (sopass_val & 0xff);
+		wol->sopass[5] = (sopass_val >> 8);
+
+		wol->wolopts |= WAKE_MAGICSECURE;
+	}
+
+	if (!(value & DP83869_WOL_ENH_MAC))
+		wol->wolopts = 0;
+}
+
 static int dp83869_config_port_mirroring(struct phy_device *phydev)
 {
 	struct dp83869_private *dp83869 = phydev->priv;
@@ -568,6 +741,9 @@ static struct phy_driver dp83869_driver[] = {
 		.config_intr	= dp83869_config_intr,
 		.read_status	= dp83869_read_status,
 
+		.get_wol	= dp83869_get_wol,
+		.set_wol	= dp83869_set_wol,
+
 		.suspend	= genphy_suspend,
 		.resume		= genphy_resume,
 	},
Signature · 1 line
2.28.0.585.ge1cfff676549
author
#3 lore raw

PATCH RESEND v5 2/2 net: phy: dp83869: Add speed optimization feature

In reply to Dan Murphy

Set the speed optimization bit on the DP83869 PHY.

Speed optimization, also known as link downshift, enables fallback to 100M operation after multiple consecutive failed attempts at Gigabit link establishment. Such a case could occur if cabling with only four wires (two twisted pairs) were connected instead of the standard cabling with eight wires (four twisted pairs).

The number of failed link attempts before falling back to 100M operation is configurable. By default, four failed link attempts are required before falling back to 100M.

---
 drivers/net/phy/dp83869.c | 116 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 116 insertions(+)
drivers/net/phy/dp83869.c +116 -0
index de68e56faf3d..0aee5f645b71 100644
@@ -11,6 +11,7 @@
 #include <linux/of.h>
 #include <linux/phy.h>
 #include <linux/delay.h>
+#include <linux/bitfield.h>
 
 #include <dt-bindings/net/ti-dp83869.h>
 
@@ -20,6 +21,7 @@
 #define MII_DP83869_PHYCTRL	0x10
 #define MII_DP83869_MICR	0x12
 #define MII_DP83869_ISR		0x13
+#define DP83869_CFG2		0x14
 #define DP83869_CTRL		0x1f
 #define DP83869_CFG4		0x1e
 
@@ -120,6 +122,18 @@
 #define DP83869_WOL_SEC_EN		BIT(5)
 #define DP83869_WOL_ENH_MAC		BIT(7)
 
+/* CFG2 bits */
+#define DP83869_DOWNSHIFT_EN		(BIT(8) | BIT(9))
+#define DP83869_DOWNSHIFT_ATTEMPT_MASK	(BIT(10) | BIT(11))
+#define DP83869_DOWNSHIFT_1_COUNT_VAL	0
+#define DP83869_DOWNSHIFT_2_COUNT_VAL	1
+#define DP83869_DOWNSHIFT_4_COUNT_VAL	2
+#define DP83869_DOWNSHIFT_8_COUNT_VAL	3
+#define DP83869_DOWNSHIFT_1_COUNT	1
+#define DP83869_DOWNSHIFT_2_COUNT	2
+#define DP83869_DOWNSHIFT_4_COUNT	4
+#define DP83869_DOWNSHIFT_8_COUNT	8
+
 enum {
 	DP83869_PORT_MIRRORING_KEEP,
 	DP83869_PORT_MIRRORING_EN,
@@ -350,6 +364,99 @@ static void dp83869_get_wol(struct phy_device *phydev,
 		wol->wolopts = 0;
 }
 
+static int dp83869_get_downshift(struct phy_device *phydev, u8 *data)
+{
+	int val, cnt, enable, count;
+
+	val = phy_read(phydev, DP83869_CFG2);
+	if (val < 0)
+		return val;
+
+	enable = FIELD_GET(DP83869_DOWNSHIFT_EN, val);
+	cnt = FIELD_GET(DP83869_DOWNSHIFT_ATTEMPT_MASK, val);
+
+	switch (cnt) {
+	case DP83869_DOWNSHIFT_1_COUNT_VAL:
+		count = DP83869_DOWNSHIFT_1_COUNT;
+		break;
+	case DP83869_DOWNSHIFT_2_COUNT_VAL:
+		count = DP83869_DOWNSHIFT_2_COUNT;
+		break;
+	case DP83869_DOWNSHIFT_4_COUNT_VAL:
+		count = DP83869_DOWNSHIFT_4_COUNT;
+		break;
+	case DP83869_DOWNSHIFT_8_COUNT_VAL:
+		count = DP83869_DOWNSHIFT_8_COUNT;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*data = enable ? count : DOWNSHIFT_DEV_DISABLE;
+
+	return 0;
+}
+
+static int dp83869_set_downshift(struct phy_device *phydev, u8 cnt)
+{
+	int val, count;
+
+	if (cnt > DP83869_DOWNSHIFT_8_COUNT)
+		return -EINVAL;
+
+	if (!cnt)
+		return phy_clear_bits(phydev, DP83869_CFG2,
+				      DP83869_DOWNSHIFT_EN);
+
+	switch (cnt) {
+	case DP83869_DOWNSHIFT_1_COUNT:
+		count = DP83869_DOWNSHIFT_1_COUNT_VAL;
+		break;
+	case DP83869_DOWNSHIFT_2_COUNT:
+		count = DP83869_DOWNSHIFT_2_COUNT_VAL;
+		break;
+	case DP83869_DOWNSHIFT_4_COUNT:
+		count = DP83869_DOWNSHIFT_4_COUNT_VAL;
+		break;
+	case DP83869_DOWNSHIFT_8_COUNT:
+		count = DP83869_DOWNSHIFT_8_COUNT_VAL;
+		break;
+	default:
+		phydev_err(phydev,
+			   "Downshift count must be 1, 2, 4 or 8\n");
+		return -EINVAL;
+	}
+
+	val = DP83869_DOWNSHIFT_EN;
+	val |= FIELD_PREP(DP83869_DOWNSHIFT_ATTEMPT_MASK, count);
+
+	return phy_modify(phydev, DP83869_CFG2,
+			  DP83869_DOWNSHIFT_EN | DP83869_DOWNSHIFT_ATTEMPT_MASK,
+			  val);
+}
+
+static int dp83869_get_tunable(struct phy_device *phydev,
+			       struct ethtool_tunable *tuna, void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return dp83869_get_downshift(phydev, data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static int dp83869_set_tunable(struct phy_device *phydev,
+			       struct ethtool_tunable *tuna, const void *data)
+{
+	switch (tuna->id) {
+	case ETHTOOL_PHY_DOWNSHIFT:
+		return dp83869_set_downshift(phydev, *(const u8 *)data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
 static int dp83869_config_port_mirroring(struct phy_device *phydev)
 {
 	struct dp83869_private *dp83869 = phydev->priv;
@@ -642,6 +749,12 @@ static int dp83869_config_init(struct phy_device *phydev)
 	struct dp83869_private *dp83869 = phydev->priv;
 	int ret, val;
 
+	/* Force speed optimization for the PHY even if it strapped */
+	ret = phy_modify(phydev, DP83869_CFG2, DP83869_DOWNSHIFT_EN,
+			 DP83869_DOWNSHIFT_EN);
+	if (ret)
+		return ret;
+
 	ret = dp83869_configure_mode(phydev, dp83869);
 	if (ret)
 		return ret;
@@ -741,6 +854,9 @@ static struct phy_driver dp83869_driver[] = {
 		.config_intr	= dp83869_config_intr,
 		.read_status	= dp83869_read_status,
 
+		.get_tunable	= dp83869_get_tunable,
+		.set_tunable	= dp83869_set_tunable,
+
 		.get_wol	= dp83869_get_wol,
 		.set_wol	= dp83869_set_wol,
 
Signature · 1 line
2.28.0.585.ge1cfff676549
maintainer Reviewed-by on v5 2/2
#4 lore raw

Re: [RESEND PATCH net-next v5 2/2] net: phy: dp83869: Add speed optimization feature

In reply to Dan Murphy
Quoted 8 lines · Dan Murphy

Set the speed optimization bit on the DP83869 PHY.

Speed optimization, also known as link downshift, enables fallback to 100M operation after multiple consecutive failed attempts at Gigabit link establishment. Such a case could occur if cabling with only four wires (two twisted pairs) were connected instead of the standard cabling with eight wires (four twisted pairs).

Quoted 5 lines

The number of failed link attempts before falling back to 100M operation is configurable. By default, four failed link attempts are required before falling back to 100M.

drivers/net/phy/dp83869.c static void dp83869_get_wol(struct phy_device *phydev, · line 428

Quoted 5 lines
drivers/net/phy/dp83869.c +5 -0
+	default:
+		phydev_err(phydev,
+			   "Downshift count must be 1, 2, 4 or 8\n");
+		return -EINVAL;
+	}

At some point it would be good to plumb in extack so we could return this to user space.

Andrew