Skip to contentSkip to conversation

samsung: exynos: convert clkout to module driver

PATCH In review Krzysztof Kozlowski 3 participants 11 messages Oct 1, 2020 – Oct 28, 2020

Subsystems (3)
lore
Share & tools
lore

Krzysztof Kozlowski

author maintainer
#0 lore raw

cover samsung: exynos: convert clkout to module driver

Hi,

The patch #2 depends on #1. I could take it via samsung-soc or both could go via samsung-clk tree.

The patchset is a proper solution to issue reported by Marek [1], for which a revert was done [2].

[1] https://lore.kernel.org/linux-samsung-soc/[email protected]/T/#m726edc89ff2927cf5aaf8b165128b3e3c45a677a
[2] https://lore.kernel.org/linux-samsung-soc/[email protected]/T/#u

Best regards,
Krzysztof

Krzysztof Kozlowski (2):
soc: samsung: exynos-pmu: instantiate clkout driver as MFD
clk: samsung: exynos-clkout: convert to module driver

 drivers/clk/samsung/clk-exynos-clkout.c | 198 +++++++++++++++++-------
 drivers/soc/samsung/exynos-pmu.c        |  11 ++
 2 files changed, 152 insertions(+), 57 deletions(-)
Signature · 1 line
2.17.1
author maintainer
#1 lore raw

PATCH 1/2 soc: samsung: exynos-pmu: instantiate clkout driver as MFD

The Exynos clock output (clkout) driver uses same register address space (Power Management Unit address space) as Exynos PMU driver and same set of compatibles. It was modeled as clock provider instantiated with CLK_OF_DECLARE_DRIVE().

This however brings ordering problems and lack of probe deferral, therefore clkout driver should be converted to a regular module and instantiated as a child of PMU driver to be able to use existing compatibles and address space.

---
 drivers/soc/samsung/exynos-pmu.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/soc/samsung/exynos-pmu.c +11 -0
index 17304fa18429..a18c93a4646c 100644
@@ -8,6 +8,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
+#include <linux/mfd/core.h>
 #include <linux/mfd/syscon.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
@@ -97,6 +98,10 @@ static const struct of_device_id exynos_pmu_of_device_ids[] = {
 	{ /*sentinel*/ },
 };
 
+static const struct mfd_cell exynos_pmu_devs[] = {
+	{ .name = "exynos-clkout", },
+};
+
 struct regmap *exynos_get_pmu_regmap(void)
 {
 	struct device_node *np = of_find_matching_node(NULL,
@@ -110,6 +115,7 @@ EXPORT_SYMBOL_GPL(exynos_get_pmu_regmap);
 static int exynos_pmu_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
+	int ret;
 
 	pmu_base_addr = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(pmu_base_addr))
@@ -128,6 +134,11 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, pmu_context);
 
+	ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE, exynos_pmu_devs,
+				   ARRAY_SIZE(exynos_pmu_devs), NULL, 0, NULL);
+	if (ret)
+		return ret;
+
 	if (devm_of_platform_populate(dev))
 		dev_err(dev, "Error populating children, reboot and poweroff might not work properly\n");
 
Signature · 1 line
2.17.1
author maintainer
#6 lore raw

PATCH 2/2 clk: samsung: exynos-clkout: convert to module driver

In reply to Krzysztof Kozlowski

The Exynos clkout driver depends on board input clock (typically XXTI or XUSBXTI), however on Exynos4 boards these clocks were modeled as part of SoC clocks (Exynos4 clocks driver). Obviously this is not proper, but correcting it would break DT backward compatibility.

Both drivers - clkout and Exynos4 clocks - register the clock providers with CLK_OF_DECLARE/OF_DECLARE_1 so their order is fragile (in the Makefile clkout is behind Exynos4 clock). It will work only if the Exynos4 clock driver comes up before clkout.

A change in DTS adding input clock reference to Exynos4 clocks input PLL, see reverted commit eaf2d2f6895d ("ARM: dts: exynos: add input clock to CMU in Exynos4412 Odroid"), caused probe reorder: the clkout appeared before Exynos4 clock provider. Since clkout depends on Exynos4 clocks and does not support deferred probe, this did not work and caused later failure of usb3503 USB hub probe which needs clkout:

    [    5.007442] usb3503 0-0008: unable to request refclk (-517)

The Exynos clkout driver is not a critical/core clock so there is actually no problem in instantiating it later, as a regular module. This removes specific probe ordering and adds support for probe deferral.

---
 drivers/clk/samsung/clk-exynos-clkout.c | 198 +++++++++++++++++-------
 1 file changed, 141 insertions(+), 57 deletions(-)
drivers/clk/samsung/clk-exynos-clkout.c +141 -57
index 34ccb1d23bc3..68af082d4716 100644
@@ -9,10 +9,13 @@
 #include <linux/slab.h>
 #include <linux/clk.h>
 #include <linux/clk-provider.h>
+#include <linux/module.h>
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
-#include <linux/syscore_ops.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
 
 #define EXYNOS_CLKOUT_NR_CLKS		1
 #define EXYNOS_CLKOUT_PARENTS		32
@@ -28,41 +31,103 @@ struct exynos_clkout {
 	struct clk_mux mux;
 	spinlock_t slock;
 	void __iomem *reg;
+	struct device_node *np;
 	u32 pmu_debug_save;
 	struct clk_hw_onecell_data data;
 };
 
-static struct exynos_clkout *clkout;
+struct exynos_clkout_variant {
+	u32 mux_mask;
+};
 
-static int exynos_clkout_suspend(void)
-{
-	clkout->pmu_debug_save = readl(clkout->reg + EXYNOS_PMU_DEBUG_REG);
+static const struct exynos_clkout_variant exynos_clkout_exynos4 = {
+	.mux_mask	= EXYNOS4_CLKOUT_MUX_MASK,
+};
 
-	return 0;
-}
+static const struct exynos_clkout_variant exynos_clkout_exynos5 = {
+	.mux_mask	= EXYNOS5_CLKOUT_MUX_MASK,
+};
 
-static void exynos_clkout_resume(void)
+static const struct of_device_id exynos_clkout_ids[] = {
+	{
+		.compatible = "samsung,exynos3250-pmu",
+		.data = &exynos_clkout_exynos4,
+	}, {
+		.compatible = "samsung,exynos4210-pmu",
+		.data = &exynos_clkout_exynos4,
+	}, {
+		.compatible = "samsung,exynos4412-pmu",
+		.data = &exynos_clkout_exynos4,
+	}, {
+		.compatible = "samsung,exynos5250-pmu",
+		.data = &exynos_clkout_exynos5,
+	}, {
+		.compatible = "samsung,exynos5410-pmu",
+		.data = &exynos_clkout_exynos5,
+	}, {
+		.compatible = "samsung,exynos5420-pmu",
+		.data = &exynos_clkout_exynos5,
+	}, {
+		.compatible = "samsung,exynos5433-pmu",
+		.data = &exynos_clkout_exynos5,
+	}, { }
+};
+
+/*
+ * Device will be instantiated as child of PMU device without its own
+ * device node.  Therefore match compatibles against parent.
+ */
+static int exynos_clkout_match_parent_dev(struct device *dev, u32 *mux_mask)
 {
-	writel(clkout->pmu_debug_save, clkout->reg + EXYNOS_PMU_DEBUG_REG);
-}
+	const struct exynos_clkout_variant *variant;
+	const struct of_device_id *match;
 
-static struct syscore_ops exynos_clkout_syscore_ops = {
-	.suspend = exynos_clkout_suspend,
-	.resume = exynos_clkout_resume,
-};
+	if (!dev->parent) {
+		dev_err(dev, "not instantiated from MFD\n");
+		return -EINVAL;
+	}
+
+	match = of_match_device(exynos_clkout_ids, dev->parent);
+	if (!match) {
+		dev_err(dev, "cannot match parent device\n");
+		return -EINVAL;
+	}
+	variant = match->data;
+
+	*mux_mask = variant->mux_mask;
+	dev_err(dev, "MATCH: %x\n", variant->mux_mask);
+
+	return 0;
+}
 
-static void __init exynos_clkout_init(struct device_node *node, u32 mux_mask)
+static int exynos_clkout_probe(struct platform_device *pdev)
 {
 	const char *parent_names[EXYNOS_CLKOUT_PARENTS];
 	struct clk *parents[EXYNOS_CLKOUT_PARENTS];
-	int parent_count;
-	int ret;
-	int i;
+	struct exynos_clkout *clkout;
+	int parent_count, ret, i;
+	u32 mux_mask;
 
-	clkout = kzalloc(struct_size(clkout, data.hws, EXYNOS_CLKOUT_NR_CLKS),
-			 GFP_KERNEL);
+	clkout = devm_kzalloc(&pdev->dev,
+			      struct_size(clkout, data.hws, EXYNOS_CLKOUT_NR_CLKS),
+			      GFP_KERNEL);
 	if (!clkout)
-		return;
+		return -ENOMEM;
+
+	ret = exynos_clkout_match_parent_dev(&pdev->dev, &mux_mask);
+	if (ret)
+		return ret;
+
+	clkout->np = pdev->dev.of_node;
+	if (!clkout->np) {
+		/*
+		 * pdev->dev.parent was checked by exynos_clkout_match_parent_dev()
+		 * so it is not NULL.
+		 */
+		clkout->np = pdev->dev.parent->of_node;
+	}
+
+	platform_set_drvdata(pdev, clkout);
 
 	spin_lock_init(&clkout->slock);
 
@@ -71,7 +136,7 @@ static void __init exynos_clkout_init(struct device_node *node, u32 mux_mask)
 		char name[] = "clkoutXX";
 
 		snprintf(name, sizeof(name), "clkout%d", i);
-		parents[i] = of_clk_get_by_name(node, name);
+		parents[i] = of_clk_get_by_name(clkout->np, name);
 		if (IS_ERR(parents[i])) {
 			parent_names[i] = "none";
 			continue;
@@ -82,11 +147,13 @@ static void __init exynos_clkout_init(struct device_node *node, u32 mux_mask)
 	}
 
 	if (!parent_count)
-		goto free_clkout;
+		return -EINVAL;
 
-	clkout->reg = of_iomap(node, 0);
-	if (!clkout->reg)
+	clkout->reg = of_iomap(clkout->np, 0);
+	if (!clkout->reg) {
+		ret = -ENODEV;
 		goto clks_put;
+	}
 
 	clkout->gate.reg = clkout->reg + EXYNOS_PMU_DEBUG_REG;
 	clkout->gate.bit_idx = EXYNOS_CLKOUT_DISABLE_SHIFT;
@@ -103,17 +170,17 @@ static void __init exynos_clkout_init(struct device_node *node, u32 mux_mask)
 				&clk_mux_ops, NULL, NULL, &clkout->gate.hw,
 				&clk_gate_ops, CLK_SET_RATE_PARENT
 				| CLK_SET_RATE_NO_REPARENT);
-	if (IS_ERR(clkout->data.hws[0]))
+	if (IS_ERR(clkout->data.hws[0])) {
+		ret = PTR_ERR(clkout->data.hws[0]);
 		goto err_unmap;
+	}
 
 	clkout->data.num = EXYNOS_CLKOUT_NR_CLKS;
-	ret = of_clk_add_hw_provider(node, of_clk_hw_onecell_get, &clkout->data);
+	ret = of_clk_add_hw_provider(clkout->np, of_clk_hw_onecell_get, &clkout->data);
 	if (ret)
 		goto err_clk_unreg;
 
-	register_syscore_ops(&exynos_clkout_syscore_ops);
-
-	return;
+	return 0;
 
 err_clk_unreg:
 	clk_hw_unregister(clkout->data.hws[0]);
@@ -123,38 +190,55 @@ static void __init exynos_clkout_init(struct device_node *node, u32 mux_mask)
 	for (i = 0; i < EXYNOS_CLKOUT_PARENTS; ++i)
 		if (!IS_ERR(parents[i]))
 			clk_put(parents[i]);
-free_clkout:
-	kfree(clkout);
 
-	pr_err("%s: failed to register clkout clock\n", __func__);
+	dev_err(&pdev->dev, "failed to register clkout clock\n");
+
+	return ret;
 }
 
-/*
- * We use CLK_OF_DECLARE_DRIVER initialization method to avoid setting
- * the OF_POPULATED flag on the pmu device tree node, so later the
- * Exynos PMU platform device can be properly probed with PMU driver.
- */
+static int exynos_clkout_remove(struct platform_device *pdev)
+{
+	struct exynos_clkout *clkout = platform_get_drvdata(pdev);
+
+	of_clk_del_provider(clkout->np);
+	clk_hw_unregister(clkout->data.hws[0]);
+	iounmap(clkout->reg);
 
-static void __init exynos4_clkout_init(struct device_node *node)
+	return 0;
+}
+static int exynos_clkout_suspend(struct device *dev)
 {
-	exynos_clkout_init(node, EXYNOS4_CLKOUT_MUX_MASK);
+	struct exynos_clkout *clkout = dev_get_drvdata(dev);
+
+	clkout->pmu_debug_save = readl(clkout->reg + EXYNOS_PMU_DEBUG_REG);
+
+	return 0;
 }
-CLK_OF_DECLARE_DRIVER(exynos4210_clkout, "samsung,exynos4210-pmu",
-		exynos4_clkout_init);
-CLK_OF_DECLARE_DRIVER(exynos4412_clkout, "samsung,exynos4412-pmu",
-		exynos4_clkout_init);
-CLK_OF_DECLARE_DRIVER(exynos3250_clkout, "samsung,exynos3250-pmu",
-		exynos4_clkout_init);
-
-static void __init exynos5_clkout_init(struct device_node *node)
+
+static int exynos_clkout_resume(struct device *dev)
 {
-	exynos_clkout_init(node, EXYNOS5_CLKOUT_MUX_MASK);
+	struct exynos_clkout *clkout = dev_get_drvdata(dev);
+
+	writel(clkout->pmu_debug_save, clkout->reg + EXYNOS_PMU_DEBUG_REG);
+
+	return 0;
 }
-CLK_OF_DECLARE_DRIVER(exynos5250_clkout, "samsung,exynos5250-pmu",
-		exynos5_clkout_init);
-CLK_OF_DECLARE_DRIVER(exynos5410_clkout, "samsung,exynos5410-pmu",
-		exynos5_clkout_init);
-CLK_OF_DECLARE_DRIVER(exynos5420_clkout, "samsung,exynos5420-pmu",
-		exynos5_clkout_init);
-CLK_OF_DECLARE_DRIVER(exynos5433_clkout, "samsung,exynos5433-pmu",
-		exynos5_clkout_init);
+
+static SIMPLE_DEV_PM_OPS(exynos_clkout_pm_ops, exynos_clkout_suspend,
+			 exynos_clkout_resume);
+
+static struct platform_driver exynos_clkout_driver = {
+	.driver = {
+		.name = "exynos-clkout",
+		.of_match_table = exynos_clkout_ids,
+		.pm = &exynos_clkout_pm_ops,
+	},
+	.probe = exynos_clkout_probe,
+	.remove = exynos_clkout_remove,
+};
+module_platform_driver(exynos_clkout_driver);
+
+MODULE_AUTHOR("Krzysztof Kozlowski <[email protected]>");
+MODULE_AUTHOR("Tomasz Figa <[email protected]>");
+MODULE_DESCRIPTION("Samsung Exynos clock output driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
2.17.1
maintainer
#7 lore raw

Re: [PATCH 2/2] clk: samsung: exynos-clkout: convert to module driver

Quoting Krzysztof Kozlowski (2020-10-01 09:56:46)

Quoted 5 lines
drivers/clk/samsung/clk-exynos-clkout.c +0 -0
index 34ccb1d23bc3..68af082d4716 100644
@@ -28,41 +31,103 @@ struct exynos_clkout {

[...]

drivers/clk/samsung/clk-exynos-clkout.c struct exynos_clkout { · line 98

Quoted 8 lines
drivers/clk/samsung/clk-exynos-clkout.c +8 -0
+       if (!match) {
+               dev_err(dev, "cannot match parent device\n");
+               return -EINVAL;
+       }
+       variant = match->data;
+
+       *mux_mask = variant->mux_mask;
+       dev_err(dev, "MATCH: %x\n", variant->mux_mask);

Is this a debug print?

Quoted 4 lines
drivers/clk/samsung/clk-exynos-clkout.c +3 -0
+
+       return 0;
+}
maintainer Reviewed-by on v1 1/2
#2 lore raw

Re: [PATCH 1/2] soc: samsung: exynos-pmu: instantiate clkout driver as MFD

In reply to Krzysztof Kozlowski

Quoting Krzysztof Kozlowski (2020-10-01 09:56:45)

Quoted 5 lines

The Exynos clock output (clkout) driver uses same register address space (Power Management Unit address space) as Exynos PMU driver and same set of compatibles. It was modeled as clock provider instantiated with CLK_OF_DECLARE_DRIVE().

Quoted 7 lines

This however brings ordering problems and lack of probe deferral, therefore clkout driver should be converted to a regular module and instantiated as a child of PMU driver to be able to use existing compatibles and address space.

---

author maintainer
#8 lore raw

Re: [PATCH 2/2] clk: samsung: exynos-clkout: convert to module driver

In reply to Stephen Boyd
Quoted 16 lines · Stephen Boyd

Quoting Krzysztof Kozlowski (2020-10-01 09:56:46)

Quoted 5 lines
drivers/clk/samsung/clk-exynos-clkout.c +0 -0
index 34ccb1d23bc3..68af082d4716 100644
@@ -28,41 +31,103 @@ struct exynos_clkout {

[...]

drivers/clk/samsung/clk-exynos-clkout.c struct exynos_clkout { · line 98

Quoted 8 lines
drivers/clk/samsung/clk-exynos-clkout.c +8 -0
+       if (!match) {
+               dev_err(dev, "cannot match parent device\n");
+               return -EINVAL;
+       }
+       variant = match->data;
+
+       *mux_mask = variant->mux_mask;
+       dev_err(dev, "MATCH: %x\n", variant->mux_mask);
Quoted 1 line

Is this a debug print?

Debugging left over, thanks for catching this. I'll remove it.

Best regards,
Krzysztof

Reviewed-by Tested-by on v1 1/2
#3 lore raw

Re: [PATCH 1/2] soc: samsung: exynos-pmu: instantiate clkout driver as MFD

In reply to Krzysztof Kozlowski

Hi,

Quoted 9 lines · Krzysztof Kozlowski

The Exynos clock output (clkout) driver uses same register address space (Power Management Unit address space) as Exynos PMU driver and same set of compatibles. It was modeled as clock provider instantiated with CLK_OF_DECLARE_DRIVE().

This however brings ordering problems and lack of probe deferral, therefore clkout driver should be converted to a regular module and instantiated as a child of PMU driver to be able to use existing compatibles and address space.

It might have been cleaner to have the CLKOUT device as a PMU subnode in DT, then device instantiation would be already covered by devm_of_platform_populate(). But it gets a bit complicated to make such a change in a backward compatible way.

I have tested both patches on Trats2, where CLKOUT provides master clock for the audio codec.

Quoted 11 lines
drivers/soc/samsung/exynos-pmu.c +5 -0
@@ -128,6 +134,11 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 
  	platform_set_drvdata(pdev, pmu_context);
 
+	ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE, exynos_pmu_devs,
+				   ARRAY_SIZE(exynos_pmu_devs), NULL, 0, NULL);
+	if (ret)
+		return ret;
+
  	if (devm_of_platform_populate(dev))
  		dev_err(dev, "Error populating children, reboot and poweroff might not work properly\n");
author maintainer
#4 lore raw

Re: [PATCH 1/2] soc: samsung: exynos-pmu: instantiate clkout driver as MFD

Quoted 8 lines · Sylwester Nawrocki

Hi,

Quoted 5 lines · Krzysztof Kozlowski

The Exynos clock output (clkout) driver uses same register address space (Power Management Unit address space) as Exynos PMU driver and same set of compatibles. It was modeled as clock provider instantiated with CLK_OF_DECLARE_DRIVE().

Quoted 8 lines
Quoted 4 lines

This however brings ordering problems and lack of probe deferral, therefore clkout driver should be converted to a regular module and instantiated as a child of PMU driver to be able to use existing compatibles and address space.

It might have been cleaner to have the CLKOUT device as a PMU subnode in DT, then device instantiation would be already covered by devm_of_platform_populate(). But it gets a bit complicated to make such a change in a backward compatible way.

Yes, I agree, but the backward compatibility would be here a pain. Optionally the driver could check for new DTB and skip adding MFD children... but this is just simpler.

Quoted 6 lines

I have tested both patches on Trats2, where CLKOUT provides master clock for the audio codec.

Thanks!

Best regards,
Krzysztof

Tested-by Reviewed-by on v1 2/2
#9 lore raw

Re: [PATCH 2/2] clk: samsung: exynos-clkout: convert to module driver

In reply to Krzysztof Kozlowski
Quoted 17 lines · Krzysztof Kozlowski

The Exynos clkout driver depends on board input clock (typically XXTI or XUSBXTI), however on Exynos4 boards these clocks were modeled as part of SoC clocks (Exynos4 clocks driver). Obviously this is not proper, but correcting it would break DT backward compatibility.

Both drivers - clkout and Exynos4 clocks - register the clock providers with CLK_OF_DECLARE/OF_DECLARE_1 so their order is fragile (in the Makefile clkout is behind Exynos4 clock). It will work only if the Exynos4 clock driver comes up before clkout.

A change in DTS adding input clock reference to Exynos4 clocks input PLL, see reverted commit eaf2d2f6895d ("ARM: dts: exynos: add input clock to CMU in Exynos4412 Odroid"), caused probe reorder: the clkout appeared before Exynos4 clock provider. Since clkout depends on Exynos4 clocks and does not support deferred probe, this did not work and caused later failure of usb3503 USB hub probe which needs clkout:

Quoted 6 lines
     [    5.007442] usb3503 0-0008: unable to request refclk (-517)

The Exynos clkout driver is not a critical/core clock so there is actually no problem in instantiating it later, as a regular module. This removes specific probe ordering and adds support for probe deferral.

The patch looks good to me, I have tested it on Trats2, where CLKOUT provides master clock for the audio codec.

With the debug print removed feel free to apply it through your tree.

--
Regards,
Sylwester

author maintainer
#5 lore raw

Re: [PATCH 1/2] soc: samsung: exynos-pmu: instantiate clkout driver as MFD

In reply to Krzysztof Kozlowski
Quoted 10 lines · Krzysztof Kozlowski

The Exynos clock output (clkout) driver uses same register address space (Power Management Unit address space) as Exynos PMU driver and same set of compatibles. It was modeled as clock provider instantiated with CLK_OF_DECLARE_DRIVE().

This however brings ordering problems and lack of probe deferral, therefore clkout driver should be converted to a regular module and instantiated as a child of PMU driver to be able to use existing compatibles and address space.

Quoted 4 lines
---
 drivers/soc/samsung/exynos-pmu.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

Applied with all tags.

Best regards,
Krzysztof

author maintainer
#10 lore raw

Re: [PATCH 2/2] clk: samsung: exynos-clkout: convert to module driver

In reply to Krzysztof Kozlowski
Quoted 24 lines · Krzysztof Kozlowski

The Exynos clkout driver depends on board input clock (typically XXTI or XUSBXTI), however on Exynos4 boards these clocks were modeled as part of SoC clocks (Exynos4 clocks driver). Obviously this is not proper, but correcting it would break DT backward compatibility.

Both drivers - clkout and Exynos4 clocks - register the clock providers with CLK_OF_DECLARE/OF_DECLARE_1 so their order is fragile (in the Makefile clkout is behind Exynos4 clock). It will work only if the Exynos4 clock driver comes up before clkout.

A change in DTS adding input clock reference to Exynos4 clocks input PLL, see reverted commit eaf2d2f6895d ("ARM: dts: exynos: add input clock to CMU in Exynos4412 Odroid"), caused probe reorder: the clkout appeared before Exynos4 clock provider. Since clkout depends on Exynos4 clocks and does not support deferred probe, this did not work and caused later failure of usb3503 USB hub probe which needs clkout:

    [    5.007442] usb3503 0-0008: unable to request refclk (-517)

The Exynos clkout driver is not a critical/core clock so there is actually no problem in instantiating it later, as a regular module. This removes specific probe ordering and adds support for probe deferral.

Quoted 4 lines
---
 drivers/clk/samsung/clk-exynos-clkout.c | 198 +++++++++++++++++-------
 1 file changed, 141 insertions(+), 57 deletions(-)

Applied (with fixes pointed out by Sylwester).

Best regards,
Krzysztof