can: m_can: Add PCI glue driver for Intel Elkhart Lake
Subsystems (2)
PATCH 1/1 can: m_can: Add PCI glue driver for Intel Elkhart Lake
Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus. It integrates the Bosch M_CAN controller with Message RAM and the wrapper IP block with additional registers which all of them are within the same MMIO range.
Currently only interrupt control register from wrapper IP is used and the MRAM configuration is expected to come from the firmware via "bosch,mram-cfg" device property and parsed by m_can.c core.
Initial implementation is done by Felipe Balbi while he was working at Intel with later changes from Raymond Tan and me.
---
This has soft dependency to patches sent earlier by Patrik Flykt and me:
https://www.spinics.net/lists/linux-can/msg04936.html
https://www.spinics.net/lists/linux-can/msg04182.html
Soft dependency since this can be applied without them but will see the issues fixed by those patches.
--- drivers/net/can/m_can/Kconfig | 8 ++ drivers/net/can/m_can/Makefile | 1 + drivers/net/can/m_can/m_can_pci.c | 186 ++++++++++++++++++++++++++++++ 3 files changed, 195 insertions(+) create mode 100644 drivers/net/can/m_can/m_can_pci.c
drivers/net/can/m_can/Kconfig +8 -0
@@ -14,6 +14,14 @@ config CAN_M_CAN_PLATFORM This support is for devices that have the Bosch M_CAN controller IP embedded into the device and the IP is IO Mapped to the processor. +config CAN_M_CAN_PCI + tristate "Generic PCI Bus based M_CAN driver" + depends on PCI + depends on CAN_M_CAN + help + Say Y here if you want to support Bosch M_CAN controller connected + to the pci bus. + config CAN_M_CAN_TCAN4X5X depends on CAN_M_CAN depends on SPI
drivers/net/can/m_can/Makefile +1 -0
@@ -5,4 +5,5 @@ obj-$(CONFIG_CAN_M_CAN) += m_can.o obj-$(CONFIG_CAN_M_CAN_PLATFORM) += m_can_platform.o +obj-$(CONFIG_CAN_M_CAN_PCI) += m_can_pci.o obj-$(CONFIG_CAN_M_CAN_TCAN4X5X) += tcan4x5x.o
drivers/net/can/m_can/m_can_pci.c new file +186 -0
186 lines not on this page · raw message
Signature · 1 line
2.29.2
Marc Kleine-Budde
maintainerQuoted 17 lines · Jarkko Nikula
Add support for
M_CANcontroller on Intel Elkhart Lake attached to the PCI bus. It integrates the BoschM_CANcontroller with Message RAM and the wrapper IP block with additional registers which all of them are within the same MMIO range.Currently only interrupt control register from wrapper IP is used and the MRAM configuration is expected to come from the firmware via "bosch,mram-cfg" device property and parsed by
m_can.ccore.Initial implementation is done by Felipe Balbi while he was working at Intel with later changes from Raymond Tan and me.
Co-developed-by Felipe Balbi (Intel) <[email protected]>Signed-off-by Felipe Balbi (Intel) <[email protected]>Co-developed-by Raymond Tan <[email protected]>Signed-off-by Raymond Tan <[email protected]>Signed-off-by Jarkko Nikula <[email protected]>
Quoted 6 lines
---
This has soft dependency to patches sent earlier by Patrik Flykt and me:
https://www.spinics.net/lists/linux-can/msg04936.html
https://www.spinics.net/lists/linux-can/msg04182.html
Soft dependency since this can be applied without them but will see the issues fixed by those patches.
I've applied the patches to linux-can-next/m_can, which is available here
https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/commit/?h=m_can
Can you please test that branch. This will go into next, once the net/master is merged to net-next/master.
regards,
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Embedded Linux | https://www.pengutronix.de | Vertretung West/Dortmund | Phone: +49-231-2826-924 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Quoted 7 lines · Marc Kleine-Budde
I've applied the patches to linux-can-next/m_can, which is available here
https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/commit/?h=m_can
Can you please test that branch. This will go into next, once the net/master is merged to net-next/master.
Thanks, works fine at quick test. I had the patch from top of linux-next tag next-20201117 so it wasn't very far away from you branch. Will send fixes if we'll notice and hopefully ours don't cause any :-)
Jarkko
Marc Kleine-Budde
maintainerQuoted 11 lines · Jarkko Nikula
Quoted 7 lines · Marc Kleine-Budde
I've applied the patches to linux-can-next/m_can, which is available here
https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/commit/?h=m_can
Can you please test that branch. This will go into next, once the net/master is merged to net-next/master.
Thanks, works fine at quick test. I had the patch from top of linux-next tag next-20201117 so it wasn't very far away from you branch. Will send fixes if we'll notice and hopefully ours don't cause any :-)
...but that branch doesn't contain the other m_can patches that are on my m_can branch.
Thanks for testing,
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Embedded Linux | https://www.pengutronix.de | Vertretung West/Dortmund | Phone: +49-231-2826-924 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |