configs/rock64: update defconfig

Revert "configs/rock64_defconfig: remove defconfig" a5fa2469e6506ea4f5a91739aa099f63a10e45ce

bump uboot from 2017.09 to release-2020-07 from ayufan-rock64/linux-mainline-u-boot

Signed-off-by Min Xu <[email protected]>

---
 DEVELOPERS                                    |  2 +
 board/pine64/rock64/extlinux.conf             |  4 +
 board/pine64/rock64/genimage.cfg              | 23 +++++
 ...328-needs-itb-image-to-boot-properly.patch | 32 +++++++
 board/pine64/rock64/post-build.sh             |  9 ++
 board/pine64/rock64/readme.txt                | 95 +++++++++++++++++++
 configs/rock64_defconfig                      | 38 ++++++++
 7 files changed, 203 insertions(+)
 create mode 100644 board/pine64/rock64/extlinux.conf
 create mode 100644 board/pine64/rock64/genimage.cfg
 create mode 100644 board/pine64/rock64/patches/uboot/0001-Makefile-rk3328-needs-itb-image-to-boot-properly.patch
 create mode 100755 board/pine64/rock64/post-build.sh
 create mode 100644 board/pine64/rock64/readme.txt
 create mode 100644 configs/rock64_defconfig

DEVELOPERS +2 -0

index a2c7f7f..1944cbb 100644
@@ -1858,6 +1858,8 @@ F:	package/libavl/
 
 N:	Micha? ?yszczek <[email protected]>
 F:	board/altera/socrates_cyclone5/
+F:	board/pine64/rock64
+F:	configs/rock64_defconfig
 F:	configs/socrates_cyclone5_defconfig
 F:	package/netifrc/
 F:	package/openrc/

board/pine64/rock64/extlinux.conf new file +4 -0

new file mode 100644
index 0000000..bf71982
@@ -0,0 +1,4 @@
+label rock64-buildroot
+  kernel /boot/Image
+  devicetree /boot/rk3328-rock64.dtb
+  append console=ttyS2,1500000n8 root=/dev/mmcblk0p1 ro rootwait

board/pine64/rock64/genimage.cfg new file +23 -0

new file mode 100644
index 0000000..0b5a0d8
@@ -0,0 +1,23 @@
+image sdcard.img {
+    hdimage {
+    }
+
+    partition uboot-spl {
+        in-partition-table = "no"
+        image = "u-boot-tpl-spl.img"
+        offset = 32768 # 512 * 0x40 from start of sd card
+    }
+
+    partition uboot {
+        in-partition-table = "no"
+        image = "u-boot.itb"
+        offset = 262144 # 512 * 0x200 from start of sd card
+    }
+
+    partition rootfs {
+        partition-type = 0x83
+        bootable = "yes"
+        image = "rootfs.ext2"
+        size = 500M
+    }
+}

board/pine64/rock64/patches/uboot/0001-Makefile-rk3328-needs-itb-image-to-boot-properly.patch new file +32 -0

new file mode 100644
index 0000000..2d35b78
@@ -0,0 +1,32 @@
+From 211bf049084e6e374dac253138fa813682910146 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Micha=C5=82=20=C5=81yszczek?= <[email protected]>
+Date: Tue, 5 Feb 2019 22:08:54 +0100
+Subject: [PATCH] Makefile: rk3328 needs itb image to boot properly
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Micha? ?yszczek <[email protected]>
+---
+ Makefile | 5 +++++
+ 1 file changed, 5 insertions(+)
+
+diff --git a/Makefile b/Makefile
+index 8086f3c93e..a6425b5b03 100644
+--- a/Makefile
++++ b/Makefile
+@@ -799,6 +799,11 @@ ifneq ($(BUILD_ROM),)
+ ALL-$(CONFIG_X86_RESET_VECTOR) += u-boot.rom
+ endif
+ 
++# rk3328 needs itb image to boot properly
++ifeq ($(CONFIG_ROCKCHIP_RK3328),y)
++ALL-y += u-boot.itb
++endif
++
+ # enable combined SPL/u-boot/dtb rules for tegra
+ ifeq ($(CONFIG_TEGRA)$(CONFIG_SPL),yy)
+ ALL-y += u-boot-tegra.bin u-boot-nodtb-tegra.bin
+-- 
+2.18.1
+

board/pine64/rock64/post-build.sh new file +9 -0

new file mode 100755
index 0000000..26b53cb
@@ -0,0 +1,9 @@
+#!/bin/sh
+
+MKIMAGE=$HOST_DIR/bin/mkimage
+BOARD_DIR="$(dirname $0)"
+
+$MKIMAGE -n rk3328 -T rksd -d $BINARIES_DIR/u-boot-tpl.bin $BINARIES_DIR/u-boot-tpl.img
+cat $BINARIES_DIR/u-boot-tpl.img $BINARIES_DIR/u-boot-spl.bin > $BINARIES_DIR/u-boot-tpl-spl.img
+
+install -m 0644 -D $BOARD_DIR/extlinux.conf $TARGET_DIR/boot/extlinux/extlinux.conf

board/pine64/rock64/readme.txt new file +95 -0

new file mode 100644
index 0000000..029c676
@@ -0,0 +1,95 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Rock64. With this default configuration you
+can log in into board via uart and look around.
+
+Board homepage: https://www.pine64.org/?page_id=7147
+
+Build
+=====
+
+First, load rock64 config for buildroot
+
+  $ make rock64_defconfig
+
+Optionally make changes to buildroot config (to install more programs)
+
+  $ make menuconfig
+
+And then build everything
+
+  $ make
+
+When completed, following files will be generated in output/images directory:
+
+  .
+  ??? Image
+  ??? bl31.bin
+  ??? bl31.elf
+  ??? rk3328-rock64.dtb
+  ??? rootfs.ext2
+  ??? rootfs.ext4 -> rootfs.ext2
+  ??? rootfs.tar
+  ??? sdcard.img
+  ??? u-boot-spl.bin
+  ??? u-boot-tpl-spl.img
+  ??? u-boot-tpl.bin
+  ??? u-boot-tpl.img
+  ??? u-boot.bin
+  ??? u-boot.itb
+
+Creating bootable SD card
+=========================
+
+!!! THIS COMMAND MAY WIPE YOUR DISK!
+!!! MAKE SURE YOU PASSED CORRECT DEVICE!
+!!! OR IT THIS WILL WIPE YOUR DISK!
+
+Simply invoke (as root)
+
+  # dd if=output/images/sdcard.img of=/dev/sdX && sync
+
+Where X is your SD card device (not partition), of= argument may also be
+/dev/mmcblk0 if you are using built-in sd card reader.
+
+Runtime
+=======
+
+Login
+-----
+
+By default, buildroot has no password, just type 'root' as login user, and
+you will be logged in.
+
+Serial console
+--------------
+
+Serial console needs to be connected to pins (into 40pin rpi compatible part)
+
+pin 6:  gnd
+pin 8:  tx
+pin 10: rx
+
+Pin numbers are printed on board.
+
+Uart configuration is not standard. Rock64 uses 1500000 (1,5M) baudrate
+with standard 8n1.
+
+Ethernet
+--------
+
+To enable ethernet you need to load modules for it:
+
+# modprobe stmmac
+# modprobe dwmac-rk
+
+and since by default there is no dhcp installed, you need to configure ip
+address, remember to change address to fit your network.
+
+# ifconfig eth0 up
+# ip addr add 10.1.1.180/24 dev eth0
+# ping 10.1.1.1
+PING 10.1.1.1 (10.1.1.1): 56 data bytes
+64 bytes from 10.1.1.1: seq=0 ttl=64 time=0.695 ms

configs/rock64_defconfig new file +38 -0

new file mode 100644
index 0000000..df03e35
@@ -0,0 +1,38 @@
+BR2_aarch64=y
+BR2_GLOBAL_PATCH_DIR="board/pine64/rock64/patches"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_19=y
+BR2_TARGET_GENERIC_GETTY_PORT="ttyS2"
+BR2_ROOTFS_POST_BUILD_SCRIPT="board/pine64/rock64/post-build.sh"
+BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/pine64/rock64/genimage.cfg"
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION=y
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.19.19"
+BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="rockchip/rk3328-rock64"
+BR2_LINUX_KERNEL_INSTALL_TARGET=y
+BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
+BR2_TARGET_ROOTFS_EXT2=y
+BR2_TARGET_ROOTFS_EXT2_4=y
+BR2_TARGET_ROOTFS_EXT2_SIZE="128M"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="rk3328"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="bl31/*.elf"
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
+BR2_TARGET_UBOOT_CUSTOM_GIT=y
+BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/ayufan-rock64/linux-mainline-u-boot.git"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="release-2020-07"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="rock64-rk3328"
+BR2_TARGET_UBOOT_NEEDS_DTC=y
+BR2_TARGET_UBOOT_NEEDS_PYTHON3=y
+BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y
+BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y
+BR2_TARGET_UBOOT_NEEDS_ATF_BL31_ELF=y
+BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
+BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.itb"
+BR2_TARGET_UBOOT_SPL=y
+BR2_TARGET_UBOOT_SPL_NAME="spl/u-boot-spl.bin tpl/u-boot-tpl.bin"
+BR2_PACKAGE_HOST_GENIMAGE=y
+BR2_PACKAGE_HOST_UBOOT_TOOLS=y

Signature · 1 line

2.20.1

Revert "configs/rock64_defconfig: remove defconfig" a5fa2469e6506ea4f5a91739aa099f63a10e45ce

bump uboot from 2017.09 to release-2020-07 from ayufan-rock64/linux-mainline-u-boot

Signed-off-by Min Xu <[email protected]>

Hello,

Quoted 1 line · On Tue, 15 Dec 2020 00:49:03 +0000 Min Xu <[email protected]> wrote:

Revert "configs/rock64_defconfig: remove defconfig"

a5fa2469e6506ea4f5a91739aa099f63a10e45ce

Quoted 2 lines

bump uboot from 2017.09 to release-2020-07 from

ayufan-rock64/linux-mainline-u-boot

Quoted 2 lines

Signed-off-by Min Xu <[email protected]>

Thanks, I've applied to master, with two changes. First, I changed the commit title to "configs/rock64: new defconfig", as this commit is not "updating" a defconfig, it's really adding a new one.

configs/rock64_defconfig line 21

Quoted 3 lines

configs/rock64_defconfig new file +3 -0

+BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="rk3328"
+BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="bl31/*.elf"

I've added a fixed version of ATF here instead of relying on the default "latest" version, which can change over time.

Thanks,

Thomas
--
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com