Skip to contentSkip to conversation

imx8mq: configs: add support for distro boot commands

PATCH Superseded Alice Guo (OSS) 1 participant 2 messages Dec 18, 2020 Arm i.MX and Layerscape

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/2 imx8mq: configs: add support for distro boot commands

From: Alice Guo <[email protected]>

Supported boot device types in iMX8MQ: MMC, DHCP.

CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is for command fstype.

scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.

kernel_addr_r is the location in RAM where the kernel will be loaded to.

Delete unnecessary environment variables because "run distro_bootcmd" is set to be the default boot mode.

---

Changes for v2:
- re-add boot_fit, initrd_addr and bootm_size which may need to be used

 configs/imx8mq_evk_defconfig |  2 +
 include/configs/imx8mq_evk.h | 76 ++++++------------------------------
 2 files changed, 14 insertions(+), 64 deletions(-)
configs/imx8mq_evk_defconfig +2 -0
index de91a76d41..901841ea36 100644
@@ -36,6 +36,8 @@ CONFIG_CMD_EXT2=y
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_EXT4_WRITE=y
 CONFIG_CMD_FAT=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_FS_GENERIC=y
 CONFIG_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
include/configs/imx8mq_evk.h +12 -64

92 lines not on this page · raw message

--
2.17.1

#1 lore raw

PATCH v2 2/2 board: imx8mq: add boot.cmd for distro boot on iMX8MQ

From: Alice Guo <[email protected]>

Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg

The boot.cmd file is an example script and can be modified based on needs. bootargs is set in this script and root uses the default value "/dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

On the iMX8MQ platform I used, "mmc0" represents eMMC and "mmc1" represents SD card.

---

Changes for v2:
- none

 board/freescale/imx8mq_evk/boot.cmd | 35 +++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 board/freescale/imx8mq_evk/boot.cmd
board/freescale/imx8mq_evk/boot.cmd new file +35 -0
new file mode 100644
index 0000000000..964993e144
@@ -0,0 +1,35 @@
+setenv bootargs console=${console} root=${mmcroot};
+
+for boot_target in ${boot_targets};
+do
+        if test "${boot_target}" = "mmc0" ; then
+                if fatload mmc 0:${mmcpart} ${kernel_addr_r} ${image}; then
+                        if fatload mmc 0:${mmcpart} ${fdt_addr} ${fdt_file}; then
+                                echo Load image and .dtb from eMMC(mmc0);
+                                booti ${kernel_addr_r} - ${fdt_addr};
+                                exit;
+                        fi
+                fi
+        fi
+
+        if test "${boot_target}" = "mmc1" ; then
+                if fatload mmc 1:${mmcpart} ${kernel_addr_r} ${image}; then
+                        if fatload mmc 1:${mmcpart} ${fdt_addr} ${fdt_file}; then
+                                echo Load image and .dtb from SD card(mmc1);
+                                booti ${kernel_addr_r} - ${fdt_addr};
+                                exit;
+                        fi
+                fi
+        fi
+
+        if test "${boot_target}" = "dhcp" ; then
+                if dhcp ${kernel_addr_r} ${serverip}:${image}; then
+                        if dhcp ${fdt_addr} ${serverip}:${fdt_file}; then
+                                echo Load image and .dtb from net(dhcp);
+                                booti ${kernel_addr_r} - ${fdt_addr};
+                                exit;
+                        fi
+                fi
+        fi
+
+done

--
2.17.1