Skip to contentSkip to conversation

AM64: Add SERDES bindings and driver support

PATCH In review Kishon Vijay Abraham I 4 participants 17 messages Dec 24, 2020 – Jan 13, 2021

Subsystems (3)
lore
Share & tools
lore
#1 lore raw

PATCH 1/7 dt-bindings: phy: ti,phy-j721e-wiz: Add bindings for AM64 SERDES Wrapper

In reply to Kishon Vijay Abraham I

Add bindings for AM64 SERDES Wrapper.

---
 .../devicetree/bindings/phy/ti,phy-j721e-wiz.yaml      | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +7 -3
index c33e9bc79521..4a1f9c27b5f0 100644
@@ -12,9 +12,13 @@ maintainers:
 
 properties:
   compatible:
-    enum:
-      - ti,j721e-wiz-16g
-      - ti,j721e-wiz-10g
+    oneOf:
+      - const: ti,j721e-wiz-16g
+      - const: ti,j721e-wiz-10g
+      - const: ti,am64-wiz-10g
+      - items:
+          - const: ti,am64-wiz-10g
+          - const: ti,j721e-wiz-10g
 
   power-domains:
     maxItems: 1
Signature · 1 line
2.17.1
#5 lore raw

PATCH 3/7 dt-bindings: phy: cadence-torrent: Add binding for refclk driver

In reply to Kishon Vijay Abraham I

Add binding for refclk driver used to route the refclk out of the SERDES.

---
 .../bindings/phy/phy-cadence-torrent.yaml       | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml +17 -0
index e266ade53d87..d3b96afd514c 100644
@@ -125,6 +125,23 @@ patternProperties:
 
     additionalProperties: false
 
+  "^refclk-driver":
+    type: object
+    description: |
+      Driver to route the reference clock out of the SERDES.
+    properties:
+      clocks:
+        maxItems: 1
+        description: Phandle to clock nodes representing the input to the
+          refclk driver.
+
+      "#clock-cells":
+        const: 0
+
+    required:
+      - clocks
+      - "#clock-cells"
+
 required:
   - compatible
   - "#address-cells"
Signature · 1 line
2.17.1
#0 lore raw

cover AM64: Add SERDES bindings and driver support

AM64 uses the same SERDES as in J7200, however AM642 EVM doesn't have a clock generator (unlike J7200 base board). Here the clock from the SERDES has to be routed to the PCIE connector. This series adds support to drive reference clock output from SERDES and also adds SERDES (torrent) and SERDES wrapper (WIZ) bindings.

Kishon Vijay Abraham I (7):
dt-bindings: phy: ti,phy-j721e-wiz: Add bindings for AM64 SERDES
Wrapper
dt-bindings: phy: ti,phy-j721e-wiz: Add binding for phy_en_refclk
dt-bindings: phy: cadence-torrent: Add binding for refclk driver
dt-bindings: ti-serdes-mux: Add defines for AM64 SoC
phy: ti: j721e-wiz: Configure full rate divider for AM64
phy: ti: j721e-wiz: Enable reference clock output in cmn_refclk_<p/m>
phy: cadence-torrent: Add support to drive refclk out

 .../bindings/phy/phy-cadence-torrent.yaml     |  17 ++
 .../bindings/phy/ti,phy-j721e-wiz.yaml        |  23 ++-
 drivers/phy/cadence/phy-cadence-torrent.c     | 158 ++++++++++++++++++
 drivers/phy/ti/phy-j721e-wiz.c                | 158 +++++++++++++++++-
 include/dt-bindings/mux/ti-serdes.h           |   4 +
 5 files changed, 354 insertions(+), 6 deletions(-)
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#7 lore raw

PATCH 4/7 dt-bindings: ti-serdes-mux: Add defines for AM64 SoC

AM64 has a single lane SERDES which can be configured to be used with either PCIe or USB. Define the possilbe values for the SERDES function in AM64 SoC here.

---
 include/dt-bindings/mux/ti-serdes.h | 4 ++++
 1 file changed, 4 insertions(+)
include/dt-bindings/mux/ti-serdes.h +4 -0
index 9047ec6bd3cf..68e0f76deed1 100644
@@ -90,4 +90,8 @@
 #define J7200_SERDES0_LANE3_USB			0x2
 #define J7200_SERDES0_LANE3_IP4_UNUSED		0x3
 
+/* AM64 */
+#define AM64_SERDES0_LANE0_PCIE0		0x0
+#define AM64_SERDES0_LANE0_USB			0x1
+
 #endif /* _DT_BINDINGS_MUX_TI_SERDES */
Signature · 1 line
2.17.1
#14 lore raw

PATCH 6/7 phy: ti: j721e-wiz: Enable reference clock output in cmn_refclk_<p/m>

In reply to Kishon Vijay Abraham I

cmn_refclk_<p/m> lines in Torrent SERDES is used for connecting external reference clock. cmn_refclk_<p/m> can also be configured to output the reference clock. In order to drive the refclk out from the SERDES (Cadence Torrent), PHY_EN_REFCLK should be set in SERDES_RST of WIZ. Model PHY_EN_REFCLK as a clock, so that platforms like AM642 EVM can enable it.

---
 drivers/phy/ti/phy-j721e-wiz.c | 115 +++++++++++++++++++++++++++++++++
 1 file changed, 115 insertions(+)
drivers/phy/ti/phy-j721e-wiz.c +115 -0
index 08acfab1ebe6..d60a9a01a8b2 100644
@@ -54,6 +54,7 @@ enum wiz_refclk_div_sel {
 
 static const struct reg_field por_en = REG_FIELD(WIZ_SERDES_CTRL, 31, 31);
 static const struct reg_field phy_reset_n = REG_FIELD(WIZ_SERDES_RST, 31, 31);
+static const struct reg_field phy_en_refclk = REG_FIELD(WIZ_SERDES_RST, 30, 30);
 static const struct reg_field pll1_refclk_mux_sel =
 					REG_FIELD(WIZ_SERDES_RST, 29, 29);
 static const struct reg_field pll0_refclk_mux_sel =
@@ -141,6 +142,15 @@ struct wiz_clk_div_sel {
 	const char		*node_name;
 };
 
+struct wiz_phy_en_refclk {
+	struct clk_hw		hw;
+	struct regmap_field	*phy_en_refclk;
+	struct clk_init_data	clk_data;
+};
+
+#define to_wiz_phy_en_refclk(_hw)	\
+			container_of(_hw, struct wiz_phy_en_refclk, hw)
+
 static struct wiz_clk_mux_sel clk_mux_sel_16g[] = {
 	{
 		/*
@@ -214,6 +224,7 @@ struct wiz {
 	unsigned int		clk_div_sel_num;
 	struct regmap_field	*por_en;
 	struct regmap_field	*phy_reset_n;
+	struct regmap_field	*phy_en_refclk;
 	struct regmap_field	*p_enable[WIZ_MAX_LANES];
 	struct regmap_field	*p_align[WIZ_MAX_LANES];
 	struct regmap_field	*p_raw_auto_start[WIZ_MAX_LANES];
@@ -450,9 +461,96 @@ static int wiz_regfield_init(struct wiz *wiz)
 		return PTR_ERR(wiz->typec_ln10_swap);
 	}
 
+	wiz->phy_en_refclk = devm_regmap_field_alloc(dev, regmap,
+						     phy_en_refclk);
+	if (IS_ERR(wiz->phy_en_refclk)) {
+		dev_err(dev, "PHY_EN_REFCLK reg field init failed\n");
+		return PTR_ERR(wiz->phy_en_refclk);
+	}
+
 	return 0;
 }
 
+static int wiz_phy_en_refclk_enable(struct clk_hw *hw)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk = to_wiz_phy_en_refclk(hw);
+	struct regmap_field *phy_en_refclk = wiz_phy_en_refclk->phy_en_refclk;
+
+	regmap_field_write(phy_en_refclk, 1);
+
+	return 0;
+}
+
+static void wiz_phy_en_refclk_disable(struct clk_hw *hw)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk = to_wiz_phy_en_refclk(hw);
+	struct regmap_field *phy_en_refclk = wiz_phy_en_refclk->phy_en_refclk;
+
+	regmap_field_write(phy_en_refclk, 0);
+}
+
+static int wiz_phy_en_refclk_is_enabled(struct clk_hw *hw)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk = to_wiz_phy_en_refclk(hw);
+	struct regmap_field *phy_en_refclk = wiz_phy_en_refclk->phy_en_refclk;
+	int val;
+
+	regmap_field_read(phy_en_refclk, &val);
+
+	return !!val;
+}
+
+static const struct clk_ops wiz_phy_en_refclk_ops = {
+	.enable = wiz_phy_en_refclk_enable,
+	.disable = wiz_phy_en_refclk_disable,
+	.is_enabled = wiz_phy_en_refclk_is_enabled,
+};
+
+static int wiz_phy_en_refclk_register(struct wiz *wiz, struct device_node *node,
+				      struct regmap_field *phy_en_refclk)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk;
+	struct device *dev = wiz->dev;
+	struct clk_init_data *init;
+	unsigned int num_parents;
+	const char *parent_name;
+	char clk_name[100];
+	struct clk *clk;
+	int ret;
+
+	wiz_phy_en_refclk = devm_kzalloc(dev, sizeof(*wiz_phy_en_refclk),
+					 GFP_KERNEL);
+	if (!wiz_phy_en_refclk)
+		return -ENOMEM;
+
+	num_parents = of_clk_get_parent_count(node);
+	parent_name = of_clk_get_parent_name(node, 0);
+
+	snprintf(clk_name, sizeof(clk_name), "%s_%s", dev_name(dev),
+		 node->name);
+
+	init = &wiz_phy_en_refclk->clk_data;
+
+	init->ops = &wiz_phy_en_refclk_ops;
+	init->flags = 0;
+	init->parent_names = parent_name ? &parent_name : NULL;
+	init->num_parents = num_parents ? 1 : 0;
+	init->name = clk_name;
+
+	wiz_phy_en_refclk->phy_en_refclk = phy_en_refclk;
+	wiz_phy_en_refclk->hw.init = init;
+
+	clk = devm_clk_register(dev, &wiz_phy_en_refclk->hw);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
+	if (ret)
+		dev_err(dev, "Fail to add clock provider: %s\n", clk_name);
+
+	return ret;
+}
+
 static u8 wiz_clk_mux_get_parent(struct clk_hw *hw)
 {
 	struct wiz_clk_mux *mux = to_wiz_clk_mux(hw);
@@ -713,6 +811,20 @@ static int wiz_clock_init(struct wiz *wiz, struct device_node *node)
 		of_node_put(clk_node);
 	}
 
+	clk_node = of_get_child_by_name(node, "phy-en-refclk");
+	if (clk_node) {
+		ret = wiz_phy_en_refclk_register(wiz, clk_node,
+						 wiz->phy_en_refclk);
+		if (ret) {
+			dev_err(dev, "Failed to register %s clock\n",
+				node_name);
+			of_node_put(clk_node);
+			goto err;
+		}
+
+		of_node_put(clk_node);
+	}
+
 	return 0;
 err:
 	wiz_clock_cleanup(wiz, node);
@@ -828,6 +940,9 @@ static int wiz_get_lane_phy_types(struct device *dev, struct wiz *wiz)
 		      of_node_name_eq(subnode, "link")))
 			continue;
 
+		if (!(of_node_name_eq(subnode, "link")))
+			continue;
+
 		ret = of_property_read_u32(subnode, "reg", &reg);
 		if (ret) {
 			dev_err(dev,
Signature · 1 line
2.17.1
#3 lore raw

PATCH 2/7 dt-bindings: phy: ti,phy-j721e-wiz: Add binding for phy_en_refclk

In reply to Kishon Vijay Abraham I

Add DT binding for phy_en_refclk used to route the refclk out of the SERDES.

---
 .../devicetree/bindings/phy/ti,phy-j721e-wiz.yaml   | 13 +++++++++++++
 1 file changed, 13 insertions(+)
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +13 -0
index 4a1f9c27b5f0..14823588bc94 100644
@@ -149,6 +149,19 @@ patternProperties:
       - assigned-clocks
       - assigned-clock-parents
 
+  "^phy-en-refclk$":
+    type: object
+    description: |
+      In order to drive the refclk out from the SERDES (Cadence Torrent),
+      PHY_EN_REFCLK should be set in SERDES_RST of WIZ. Model phy-en-refclk
+      as a clock so that it can be enabled directly or as a parent clock.
+    properties:
+      "#clock-cells":
+        const: 0
+
+    required:
+      - "#clock-cells"
+
   "^serdes@[0-9a-f]+$":
     type: object
     description: |
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#12 lore raw

PATCH 5/7 phy: ti: j721e-wiz: Configure full rate divider for AM64

In reply to Kishon Vijay Abraham I

The frequency of the txmclk between PCIe and SERDES has changed to 250MHz from 500MHz. Configure full rate divider for AM64 accordingly.

---
 drivers/phy/ti/phy-j721e-wiz.c | 43 +++++++++++++++++++++++++++++++---
 1 file changed, 40 insertions(+), 3 deletions(-)
drivers/phy/ti/phy-j721e-wiz.c +40 -3
index 2a03191eac64..08acfab1ebe6 100644
@@ -101,6 +101,13 @@ static const struct reg_field p_standard_mode[WIZ_MAX_LANES] = {
 	REG_FIELD(WIZ_LANECTL(3), 24, 25),
 };
 
+static const struct reg_field p0_fullrt_div[WIZ_MAX_LANES] = {
+	REG_FIELD(WIZ_LANECTL(0), 22, 23),
+	REG_FIELD(WIZ_LANECTL(1), 22, 23),
+	REG_FIELD(WIZ_LANECTL(2), 22, 23),
+	REG_FIELD(WIZ_LANECTL(3), 22, 23),
+};
+
 static const struct reg_field typec_ln10_swap =
 					REG_FIELD(WIZ_SERDES_TYPEC, 30, 30);
 
@@ -193,6 +200,7 @@ static struct wiz_clk_div_sel clk_div_sel[] = {
 enum wiz_type {
 	J721E_WIZ_16G,
 	J721E_WIZ_10G,
+	AM64_WIZ_10G,
 };
 
 #define WIZ_TYPEC_DIR_DEBOUNCE_MIN	100	/* ms */
@@ -210,6 +218,7 @@ struct wiz {
 	struct regmap_field	*p_align[WIZ_MAX_LANES];
 	struct regmap_field	*p_raw_auto_start[WIZ_MAX_LANES];
 	struct regmap_field	*p_standard_mode[WIZ_MAX_LANES];
+	struct regmap_field	*p0_fullrt_div[WIZ_MAX_LANES];
 	struct regmap_field	*pma_cmn_refclk_int_mode;
 	struct regmap_field	*pma_cmn_refclk_mode;
 	struct regmap_field	*pma_cmn_refclk_dig_div;
@@ -380,7 +389,7 @@ static int wiz_regfield_init(struct wiz *wiz)
 	}
 
 	clk_mux_sel = &wiz->clk_mux_sel[REFCLK_DIG];
-	if (wiz->type == J721E_WIZ_10G)
+	if (wiz->type == J721E_WIZ_10G || wiz->type == AM64_WIZ_10G)
 		clk_mux_sel->field =
 			devm_regmap_field_alloc(dev, regmap,
 						refclk_dig_sel_10g);
@@ -424,6 +433,14 @@ static int wiz_regfield_init(struct wiz *wiz)
 				i);
 			return PTR_ERR(wiz->p_standard_mode[i]);
 		}
+
+		wiz->p0_fullrt_div[i] =
+			devm_regmap_field_alloc(dev, regmap, p0_fullrt_div[i]);
+		if (IS_ERR(wiz->p0_fullrt_div[i])) {
+			dev_err(dev, "P%d_FULLRT_DIV reg field init failed\n",
+				i);
+			return PTR_ERR(wiz->p0_fullrt_div[i]);
+		}
 	}
 
 	wiz->typec_ln10_swap = devm_regmap_field_alloc(dev, regmap,
@@ -719,6 +736,19 @@ static int wiz_phy_reset_assert(struct reset_controller_dev *rcdev,
 	return ret;
 }
 
+static int wiz_phy_fullrt_div(struct wiz *wiz, int lane)
+{
+	int ret = 0;
+
+	if (wiz->type != AM64_WIZ_10G)
+		return 0;
+
+	if (wiz->lane_phy_type[lane] == PHY_TYPE_PCIE)
+		ret = regmap_field_write(wiz->p0_fullrt_div[lane], 0x1);
+
+	return ret;
+}
+
 static int wiz_phy_reset_deassert(struct reset_controller_dev *rcdev,
 				  unsigned long id)
 {
@@ -742,6 +772,10 @@ static int wiz_phy_reset_deassert(struct reset_controller_dev *rcdev,
 		return ret;
 	}
 
+	ret = wiz_phy_fullrt_div(wiz, id - 1);
+	if (ret)
+		return ret;
+
 	if (wiz->lane_phy_type[id - 1] == PHY_TYPE_DP)
 		ret = regmap_field_write(wiz->p_enable[id - 1], P_ENABLE);
 	else
@@ -769,6 +803,9 @@ static const struct of_device_id wiz_id_table[] = {
 	{
 		.compatible = "ti,j721e-wiz-10g", .data = (void *)J721E_WIZ_10G
 	},
+	{
+		.compatible = "ti,am64-wiz-10g", .data = (void *)AM64_WIZ_10G
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, wiz_id_table);
@@ -904,14 +941,14 @@ static int wiz_probe(struct platform_device *pdev)
 	wiz->dev = dev;
 	wiz->regmap = regmap;
 	wiz->num_lanes = num_lanes;
-	if (wiz->type == J721E_WIZ_10G)
+	if (wiz->type == J721E_WIZ_10G || wiz->type == AM64_WIZ_10G)
 		wiz->clk_mux_sel = clk_mux_sel_10g;
 	else
 		wiz->clk_mux_sel = clk_mux_sel_16g;
 
 	wiz->clk_div_sel = clk_div_sel;
 
-	if (wiz->type == J721E_WIZ_10G)
+	if (wiz->type == J721E_WIZ_10G || wiz->type == AM64_WIZ_10G)
 		wiz->clk_div_sel_num = WIZ_DIV_NUM_CLOCKS_10G;
 	else
 		wiz->clk_div_sel_num = WIZ_DIV_NUM_CLOCKS_16G;
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#16 lore raw

PATCH 7/7 phy: cadence-torrent: Add support to drive refclk out

In reply to Kishon Vijay Abraham I

cmn_refclk_<p/m> lines in Torrent SERDES is used for connecting external reference clock. cmn_refclk_<p/m> can also be configured to output the reference clock. Model this derived reference clock as a "clock" so that platforms like AM642 EVM can enable it.
This is used by PCIe to use the same refclk both in local SERDES and remote device. Add support here to drive refclk out.

---
 drivers/phy/cadence/phy-cadence-torrent.c | 158 ++++++++++++++++++++++
 1 file changed, 158 insertions(+)
drivers/phy/cadence/phy-cadence-torrent.c +158 -0
index f310e15d94cb..ad01fb61cfa4 100644
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/phy/phy.h>
 #include <linux/clk.h>
+#include <linux/clk-provider.h>
 #include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/io.h>
@@ -76,6 +77,8 @@
  * register offsets from SD0801 PHY register block base (i.e MHDP
  * register base + 0x500000)
  */
+#define CMN_CDIAG_REFCLK_OVRD		0x004CU
+#define CMN_CDIAG_REFCLK_DRV0_CTRL	0x0050U
 #define CMN_SSM_BANDGAP_TMR		0x0021U
 #define CMN_SSM_BIAS_TMR		0x0022U
 #define CMN_PLLSM0_PLLPRE_TMR		0x002AU
@@ -206,6 +209,8 @@
 #define RX_DIAG_ACYA			0x01FFU
 
 /* PHY PCS common registers */
+#define PHY_PIPE_CMN_CTRL1		0x0000U
+#define PHY_ISO_CMN_CTRL		0x0008U
 #define PHY_PLL_CFG			0x000EU
 #define PHY_PIPE_USB3_GEN2_PRE_CFG0	0x0020U
 #define PHY_PIPE_USB3_GEN2_POST_CFG0	0x0022U
@@ -231,6 +236,36 @@ static const struct reg_field phy_pma_pll_raw_ctrl =
 static const struct reg_field phy_reset_ctrl =
 				REG_FIELD(PHY_RESET, 8, 8);
 
+#define REFCLK_OUT_NUM_CONFIGURATIONS_PCS_CONFIG	2
+
+enum cdns_torrent_refclk_out_pcs {
+	PHY_ISO_CMN_CTRL_8,
+	PHY_PIPE_CMN_CTRL1_0,
+};
+
+#define REFCLK_OUT_NUM_CONFIGURATIONS_CMN_CONFIG	5
+
+enum cdns_torrent_refclk_out_cmn {
+	CMN_CDIAG_REFCLK_OVRD_4,
+	CMN_CDIAG_REFCLK_DRV0_CTRL_1,
+	CMN_CDIAG_REFCLK_DRV0_CTRL_4,
+	CMN_CDIAG_REFCLK_DRV0_CTRL_5,
+	CMN_CDIAG_REFCLK_DRV0_CTRL_6,
+};
+
+static const struct reg_field refclk_out_pcs_cfg[] = {
+	[PHY_ISO_CMN_CTRL_8]	= REG_FIELD(PHY_ISO_CMN_CTRL, 8, 8),
+	[PHY_PIPE_CMN_CTRL1_0]	= REG_FIELD(PHY_PIPE_CMN_CTRL1, 0, 0),
+};
+
+static const struct reg_field refclk_out_cmn_cfg[] = {
+	[CMN_CDIAG_REFCLK_OVRD_4]	= REG_FIELD(CMN_CDIAG_REFCLK_OVRD, 4, 4),
+	[CMN_CDIAG_REFCLK_DRV0_CTRL_1]	= REG_FIELD(CMN_CDIAG_REFCLK_DRV0_CTRL, 1, 1),
+	[CMN_CDIAG_REFCLK_DRV0_CTRL_4]	= REG_FIELD(CMN_CDIAG_REFCLK_DRV0_CTRL, 4, 4),
+	[CMN_CDIAG_REFCLK_DRV0_CTRL_5]  = REG_FIELD(CMN_CDIAG_REFCLK_DRV0_CTRL, 5, 5),
+	[CMN_CDIAG_REFCLK_DRV0_CTRL_6]	= REG_FIELD(CMN_CDIAG_REFCLK_DRV0_CTRL, 6, 6),
+};
+
 enum cdns_torrent_phy_type {
 	TYPE_NONE,
 	TYPE_DP,
@@ -288,6 +323,16 @@ enum phy_powerstate {
 	POWERSTATE_A3 = 3,
 };
 
+struct cdns_torrent_derived_refclk {
+	struct clk_hw		hw;
+	struct regmap_field	*pcs_fields[REFCLK_OUT_NUM_CONFIGURATIONS_PCS_CONFIG];
+	struct regmap_field	*cmn_fields[REFCLK_OUT_NUM_CONFIGURATIONS_CMN_CONFIG];
+	struct clk_init_data	clk_data;
+};
+
+#define to_cdns_torrent_derived_refclk(_hw)	\
+			container_of(_hw, struct cdns_torrent_derived_refclk, hw)
+
 static int cdns_torrent_phy_init(struct phy *phy);
 static int cdns_torrent_dp_init(struct phy *phy);
 static int cdns_torrent_dp_run(struct cdns_torrent_phy *cdns_phy,
@@ -1604,6 +1649,110 @@ static int cdns_torrent_dp_run(struct cdns_torrent_phy *cdns_phy, u32 num_lanes)
 	return ret;
 }
 
+static int cdns_torrent_derived_refclk_enable(struct clk_hw *hw)
+{
+	struct cdns_torrent_derived_refclk *derived_refclk = to_cdns_torrent_derived_refclk(hw);
+
+	regmap_field_write(derived_refclk->cmn_fields[CMN_CDIAG_REFCLK_DRV0_CTRL_6], 0);
+	regmap_field_write(derived_refclk->cmn_fields[CMN_CDIAG_REFCLK_DRV0_CTRL_4], 1);
+	regmap_field_write(derived_refclk->cmn_fields[CMN_CDIAG_REFCLK_DRV0_CTRL_5], 1);
+	regmap_field_write(derived_refclk->cmn_fields[CMN_CDIAG_REFCLK_DRV0_CTRL_1], 0);
+	regmap_field_write(derived_refclk->cmn_fields[CMN_CDIAG_REFCLK_OVRD_4], 1);
+	regmap_field_write(derived_refclk->pcs_fields[PHY_PIPE_CMN_CTRL1_0], 1);
+	regmap_field_write(derived_refclk->pcs_fields[PHY_ISO_CMN_CTRL_8], 1);
+
+	return 0;
+}
+
+static void cdns_torrent_derived_refclk_disable(struct clk_hw *hw)
+{
+	struct cdns_torrent_derived_refclk *derived_refclk = to_cdns_torrent_derived_refclk(hw);
+
+	regmap_field_write(derived_refclk->pcs_fields[PHY_ISO_CMN_CTRL_8], 0);
+}
+
+static int cdns_torrent_derived_refclk_is_enabled(struct clk_hw *hw)
+{
+	struct cdns_torrent_derived_refclk *derived_refclk = to_cdns_torrent_derived_refclk(hw);
+	int val;
+
+	regmap_field_read(derived_refclk->pcs_fields[PHY_ISO_CMN_CTRL_8], &val);
+
+	return !!val;
+}
+
+static const struct clk_ops cdns_torrent_derived_refclk_ops = {
+	.enable = cdns_torrent_derived_refclk_enable,
+	.disable = cdns_torrent_derived_refclk_disable,
+	.is_enabled = cdns_torrent_derived_refclk_is_enabled,
+};
+
+static int cdns_torrent_derived_refclk_register(struct cdns_torrent_phy *cdns_phy,
+						struct device_node *node)
+{
+	struct cdns_torrent_derived_refclk *derived_refclk;
+	struct device *dev = cdns_phy->dev;
+	struct regmap_field *field;
+	struct clk_init_data *init;
+	unsigned int num_parents;
+	const char *parent_name;
+	struct regmap *regmap;
+	char clk_name[100];
+	struct clk *clk;
+	int ret, i;
+
+	derived_refclk = devm_kzalloc(dev, sizeof(*derived_refclk), GFP_KERNEL);
+	if (!derived_refclk)
+		return -ENOMEM;
+
+	num_parents = of_clk_get_parent_count(node);
+	parent_name = of_clk_get_parent_name(node, 0);
+
+	snprintf(clk_name, sizeof(clk_name), "%s_%s", dev_name(dev),
+		 node->name);
+
+	init = &derived_refclk->clk_data;
+
+	init->ops = &cdns_torrent_derived_refclk_ops;
+	init->flags = 0;
+	init->parent_names = parent_name ? &parent_name : NULL;
+	init->num_parents = num_parents ? 1 : 0;
+	init->name = clk_name;
+
+	regmap = cdns_phy->regmap_phy_pcs_common_cdb;
+	for (i = 0; i < REFCLK_OUT_NUM_CONFIGURATIONS_PCS_CONFIG; i++) {
+		field = devm_regmap_field_alloc(dev, regmap, refclk_out_pcs_cfg[i]);
+		if (IS_ERR(field)) {
+			dev_err(dev, "PCS reg field init failed\n");
+			return PTR_ERR(field);
+		}
+		derived_refclk->pcs_fields[i] = field;
+	}
+
+	regmap = cdns_phy->regmap_common_cdb;
+	for (i = 0; i < REFCLK_OUT_NUM_CONFIGURATIONS_CMN_CONFIG; i++) {
+		field = devm_regmap_field_alloc(dev, regmap, refclk_out_cmn_cfg[i]);
+		if (IS_ERR(field)) {
+			dev_err(dev, "CMN reg field init failed\n");
+			return PTR_ERR(field);
+		}
+		derived_refclk->cmn_fields[i] = field;
+	}
+
+	derived_refclk->hw.init = init;
+
+	clk = devm_clk_register(dev, &derived_refclk->hw);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
+	if (ret)
+		dev_err(dev, "Failed to add refrcv clock provider: %s\n",
+			clk_name);
+
+	return ret;
+}
+
 static int cdns_torrent_phy_on(struct phy *phy)
 {
 	struct cdns_torrent_inst *inst = phy_get_drvdata(phy);
@@ -2150,6 +2299,15 @@ static int cdns_torrent_phy_probe(struct platform_device *pdev)
 	/* Enable APB */
 	reset_control_deassert(cdns_phy->apb_rst);
 
+	child = of_get_child_by_name(dev->of_node, "refclk-driver");
+	if (child) {
+		ret = cdns_torrent_derived_refclk_register(cdns_phy, child);
+		if (ret) {
+			dev_err(dev, "failed to register derived refclk\n");
+			return ret;
+		}
+	}
+
 	for_each_available_child_of_node(dev->of_node, child) {
 		struct phy *gphy;
 
Signature · 7 lines
2.17.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer
#2 lore raw

Re: [PATCH 1/7] dt-bindings: phy: ti,phy-j721e-wiz: Add bindings for AM64 SERDES Wrapper

In reply to Kishon Vijay Abraham I
Quoted 12 lines · Kishon Vijay Abraham I

Add bindings for AM64 SERDES Wrapper.

---
 .../devicetree/bindings/phy/ti,phy-j721e-wiz.yaml      | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +0 -0
index c33e9bc79521..4a1f9c27b5f0 100644

Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml maintainers: · line 17

Quoted 9 lines
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +3 -3
@@ -12,9 +12,13 @@ maintainers:
 
 properties:
   compatible:
-    enum:
-      - ti,j721e-wiz-16g
-      - ti,j721e-wiz-10g
+    oneOf:
+      - const: ti,j721e-wiz-16g
+      - const: ti,j721e-wiz-10g

Pick one. This:

Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml maintainers: · line 18

Quoted 1 line
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +1 -0
+      - const: ti,am64-wiz-10g

Or this:

Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml maintainers: · line 21

Quoted 3 lines
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +3 -0
+      - items:
+          - const: ti,am64-wiz-10g
+          - const: ti,j721e-wiz-10g

No reason to support both for ti,am64-wiz-10g.

Quoted 6 lines
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +0 -0
   power-domains:
     maxItems: 1
Signature · 1 line
2.17.1
maintainer
#4 lore raw

Re: [PATCH 2/7] dt-bindings: phy: ti,phy-j721e-wiz: Add binding for phy_en_refclk

In reply to Kishon Vijay Abraham I
Quoted 13 lines · Kishon Vijay Abraham I

Add DT binding for phy_en_refclk used to route the refclk out of the SERDES.

---
 .../devicetree/bindings/phy/ti,phy-j721e-wiz.yaml   | 13 +++++++++++++
 1 file changed, 13 insertions(+)
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +0 -0
index 4a1f9c27b5f0..14823588bc94 100644

Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml patternProperties: · line 152

Quoted 4 lines
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +1 -0
@@ -149,6 +149,19 @@ patternProperties:
       - assigned-clocks
       - assigned-clock-parents
 
+  "^phy-en-refclk$":

Not really a pattern. Move to 'properties'.

Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml patternProperties: · line 163

Quoted 11 lines
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +11 -0
+    type: object
+    description: |
+      In order to drive the refclk out from the SERDES (Cadence Torrent),
+      PHY_EN_REFCLK should be set in SERDES_RST of WIZ. Model phy-en-refclk
+      as a clock so that it can be enabled directly or as a parent clock.
+    properties:
+      "#clock-cells":
+        const: 0
+
+    required:
+      - "#clock-cells"

Though not really any need for a child node here. Just add '#clock-cells' to the parent node.

Quoted 7 lines
Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml +1 -0
+
   "^serdes@[0-9a-f]+$":
     type: object
     description: |
Signature · 1 line
2.17.1
maintainer
#6 lore raw

Re: [PATCH 3/7] dt-bindings: phy: cadence-torrent: Add binding for refclk driver

In reply to Kishon Vijay Abraham I
Quoted 18 lines · Kishon Vijay Abraham I

Add binding for refclk driver used to route the refclk out of the SERDES.

---
 .../bindings/phy/phy-cadence-torrent.yaml       | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml +2 -0
index e266ade53d87..d3b96afd514c 100644
@@ -125,6 +125,23 @@ patternProperties:
 
     additionalProperties: false
 
+  "^refclk-driver":
+    type: object

Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml patternProperties: · line 139

Quoted 10 lines
Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml +10 -0
+    description: |
+      Driver to route the reference clock out of the SERDES.
+    properties:
+      clocks:
+        maxItems: 1
+        description: Phandle to clock nodes representing the input to the
+          refclk driver.
+
+      "#clock-cells":
+        const: 0

Just move to the parent node.

Quoted 11 lines
Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml +5 -0
+
+    required:
+      - clocks
+      - "#clock-cells"
+
 required:
   - compatible
   - "#address-cells"
Signature · 1 line
2.17.1
maintainer
#8 lore raw

Re: [PATCH 4/7] dt-bindings: ti-serdes-mux: Add defines for AM64 SoC

In reply to Kishon Vijay Abraham I
Quoted 3 lines · Kishon Vijay Abraham I

AM64 has a single lane SERDES which can be configured to be used with either PCIe or USB. Define the possilbe values for the SERDES function in AM64 SoC here.

Doesn't look like this is used? Would the common phy modes work?

Quoted 22 lines
---
 include/dt-bindings/mux/ti-serdes.h | 4 ++++
 1 file changed, 4 insertions(+)
include/dt-bindings/mux/ti-serdes.h +4 -0
index 9047ec6bd3cf..68e0f76deed1 100644
@@ -90,4 +90,8 @@
 #define J7200_SERDES0_LANE3_USB			0x2
 #define J7200_SERDES0_LANE3_IP4_UNUSED		0x3
 
+/* AM64 */
+#define AM64_SERDES0_LANE0_PCIE0		0x0
+#define AM64_SERDES0_LANE0_USB			0x1
+
 #endif /* _DT_BINDINGS_MUX_TI_SERDES */
Signature · 1 line
2.17.1
Acked-by on v1 4/7
#10 lore raw

Re: [PATCH 4/7] dt-bindings: ti-serdes-mux: Add defines for AM64 SoC

In reply to Kishon Vijay Abraham I

Hi!

Quoted 14 lines · Kishon Vijay Abraham I

AM64 has a single lane SERDES which can be configured to be used with either PCIe or USB. Define the possilbe values for the SERDES function in AM64 SoC here.

---
 include/dt-bindings/mux/ti-serdes.h | 4 ++++
 1 file changed, 4 insertions(+)
include/dt-bindings/mux/ti-serdes.h +0 -0
index 9047ec6bd3cf..68e0f76deed1 100644

include/dt-bindings/mux/ti-serdes.h line 93

Quoted 4 lines
include/dt-bindings/mux/ti-serdes.h +1 -0
@@ -90,4 +90,8 @@
 #define J7200_SERDES0_LANE3_USB			0x2
 #define J7200_SERDES0_LANE3_IP4_UNUSED		0x3
 
+/* AM64 */

In case you end up keeping these defines, despite the comment by Rob...

Nitpick, the J721E and J7200 sections have a blank line here, between the header comment and the actual defines. But mehh...

Cheers,
Peter

Quoted 5 lines
include/dt-bindings/mux/ti-serdes.h +3 -0
+#define AM64_SERDES0_LANE0_PCIE0		0x0
+#define AM64_SERDES0_LANE0_USB			0x1
+
 #endif /* _DT_BINDINGS_MUX_TI_SERDES */
#9 lore raw

Re: [PATCH 4/7] dt-bindings: ti-serdes-mux: Add defines for AM64 SoC

In reply to Rob Herring

Hi Rob,

Quoted 6 lines · Rob Herring
Quoted 3 lines · Kishon Vijay Abraham I

AM64 has a single lane SERDES which can be configured to be used with either PCIe or USB. Define the possilbe values for the SERDES function in AM64 SoC here.

Doesn't look like this is used? Would the common phy modes work?

This will be used when the dts files are added.

Thanks
Kishon

Quoted 22 lines
Quoted 22 lines
---
 include/dt-bindings/mux/ti-serdes.h | 4 ++++
 1 file changed, 4 insertions(+)
include/dt-bindings/mux/ti-serdes.h +4 -0
index 9047ec6bd3cf..68e0f76deed1 100644
@@ -90,4 +90,8 @@
 #define J7200_SERDES0_LANE3_USB			0x2
 #define J7200_SERDES0_LANE3_IP4_UNUSED		0x3
 
+/* AM64 */
+#define AM64_SERDES0_LANE0_PCIE0		0x0
+#define AM64_SERDES0_LANE0_USB			0x1
+
 #endif /* _DT_BINDINGS_MUX_TI_SERDES */
Signature · 1 line
2.17.1
#11 lore raw

Re: [PATCH 4/7] dt-bindings: ti-serdes-mux: Add defines for AM64 SoC

In reply to Peter Rosin

Hi Peter,

Quoted 20 lines · Peter Rosin

Hi!

Quoted 17 lines · Kishon Vijay Abraham I

AM64 has a single lane SERDES which can be configured to be used with either PCIe or USB. Define the possilbe values for the SERDES function in AM64 SoC here.

---
 include/dt-bindings/mux/ti-serdes.h | 4 ++++
 1 file changed, 4 insertions(+)
include/dt-bindings/mux/ti-serdes.h +0 -0
index 9047ec6bd3cf..68e0f76deed1 100644
@@ -90,4 +90,8 @@
 #define J7200_SERDES0_LANE3_USB			0x2
 #define J7200_SERDES0_LANE3_IP4_UNUSED		0x3
 
Quoted 8 lines

include/dt-bindings/mux/ti-serdes.h line 93

Quoted 1 line
include/dt-bindings/mux/ti-serdes.h +1 -0
+/* AM64 */

In case you end up keeping these defines, despite the comment by Rob...

Nitpick, the J721E and J7200 sections have a blank line here, between the header comment and the actual defines. But mehh...

Sure, will fix it in the next revision.

Thanks
Kishon

Quoted 9 lines

Cheers,
Peter

Quoted 5 lines
include/dt-bindings/mux/ti-serdes.h +3 -0
+#define AM64_SERDES0_LANE0_PCIE0		0x0
+#define AM64_SERDES0_LANE0_USB			0x1
+
 #endif /* _DT_BINDINGS_MUX_TI_SERDES */
maintainer
#13 lore raw

Re: [PATCH 5/7] phy: ti: j721e-wiz: Configure full rate divider for AM64

In reply to Kishon Vijay Abraham I
Quoted 53 lines · Kishon Vijay Abraham I

The frequency of the txmclk between PCIe and SERDES has changed to 250MHz from 500MHz. Configure full rate divider for AM64 accordingly.

---
 drivers/phy/ti/phy-j721e-wiz.c | 43 +++++++++++++++++++++++++++++++---
 1 file changed, 40 insertions(+), 3 deletions(-)
drivers/phy/ti/phy-j721e-wiz.c +10 -1
index 2a03191eac64..08acfab1ebe6 100644
@@ -101,6 +101,13 @@ static const struct reg_field p_standard_mode[WIZ_MAX_LANES] = {
 	REG_FIELD(WIZ_LANECTL(3), 24, 25),
 };
 
+static const struct reg_field p0_fullrt_div[WIZ_MAX_LANES] = {
+	REG_FIELD(WIZ_LANECTL(0), 22, 23),
+	REG_FIELD(WIZ_LANECTL(1), 22, 23),
+	REG_FIELD(WIZ_LANECTL(2), 22, 23),
+	REG_FIELD(WIZ_LANECTL(3), 22, 23),
+};
+
 static const struct reg_field typec_ln10_swap =
 					REG_FIELD(WIZ_SERDES_TYPEC, 30, 30);
 
@@ -193,6 +200,7 @@ static struct wiz_clk_div_sel clk_div_sel[] = {
 enum wiz_type {
 	J721E_WIZ_16G,
 	J721E_WIZ_10G,
+	AM64_WIZ_10G,
 };
 
 #define WIZ_TYPEC_DIR_DEBOUNCE_MIN	100	/* ms */
@@ -210,6 +218,7 @@ struct wiz {
 	struct regmap_field	*p_align[WIZ_MAX_LANES];
 	struct regmap_field	*p_raw_auto_start[WIZ_MAX_LANES];
 	struct regmap_field	*p_standard_mode[WIZ_MAX_LANES];
+	struct regmap_field	*p0_fullrt_div[WIZ_MAX_LANES];
 	struct regmap_field	*pma_cmn_refclk_int_mode;
 	struct regmap_field	*pma_cmn_refclk_mode;
 	struct regmap_field	*pma_cmn_refclk_dig_div;
@@ -380,7 +389,7 @@ static int wiz_regfield_init(struct wiz *wiz)
 	}
 
 	clk_mux_sel = &wiz->clk_mux_sel[REFCLK_DIG];
-	if (wiz->type == J721E_WIZ_10G)
+	if (wiz->type == J721E_WIZ_10G || wiz->type == AM64_WIZ_10G)
 		clk_mux_sel->field =
 			devm_regmap_field_alloc(dev, regmap,
 						refclk_dig_sel_10g);

drivers/phy/ti/phy-j721e-wiz.c static int wiz_regfield_init(struct wiz *wiz) · line 441

Quoted 9 lines
drivers/phy/ti/phy-j721e-wiz.c +6 -0
@@ -424,6 +433,14 @@ static int wiz_regfield_init(struct wiz *wiz)
 				i);
 			return PTR_ERR(wiz->p_standard_mode[i]);
 		}
+
+		wiz->p0_fullrt_div[i] =
+			devm_regmap_field_alloc(dev, regmap, p0_fullrt_div[i]);
+		if (IS_ERR(wiz->p0_fullrt_div[i])) {
+			dev_err(dev, "P%d_FULLRT_DIV reg field init failed\n",
+				i);

single line?

drivers/phy/ti/phy-j721e-wiz.c static int wiz_phy_reset_assert(struct reset_controller_dev *rcdev, · line 741

Quoted 12 lines
drivers/phy/ti/phy-j721e-wiz.c +5 -0
+			return PTR_ERR(wiz->p0_fullrt_div[i]);
+		}
 	}
 
 	wiz->typec_ln10_swap = devm_regmap_field_alloc(dev, regmap,
@@ -719,6 +736,19 @@ static int wiz_phy_reset_assert(struct reset_controller_dev *rcdev,
 	return ret;
 }
 
+static int wiz_phy_fullrt_div(struct wiz *wiz, int lane)
+{
+	int ret = 0;

drop the variable..

drivers/phy/ti/phy-j721e-wiz.c static int wiz_phy_reset_assert(struct reset_controller_dev *rcdev, · line 747

Quoted 6 lines
drivers/phy/ti/phy-j721e-wiz.c +6 -0
+
+	if (wiz->type != AM64_WIZ_10G)
+		return 0;
+
+	if (wiz->lane_phy_type[lane] == PHY_TYPE_PCIE)
+		ret = regmap_field_write(wiz->p0_fullrt_div[lane], 0x1);

return regmap_

drivers/phy/ti/phy-j721e-wiz.c static int wiz_phy_reset_assert(struct reset_controller_dev *rcdev, · line 749

Quoted 2 lines
drivers/phy/ti/phy-j721e-wiz.c +2 -0
+
+	return ret;

return 0

Quoted 45 lines
drivers/phy/ti/phy-j721e-wiz.c +11 -2
+}
+
 static int wiz_phy_reset_deassert(struct reset_controller_dev *rcdev,
 				  unsigned long id)
 {
@@ -742,6 +772,10 @@ static int wiz_phy_reset_deassert(struct reset_controller_dev *rcdev,
 		return ret;
 	}
 
+	ret = wiz_phy_fullrt_div(wiz, id - 1);
+	if (ret)
+		return ret;
+
 	if (wiz->lane_phy_type[id - 1] == PHY_TYPE_DP)
 		ret = regmap_field_write(wiz->p_enable[id - 1], P_ENABLE);
 	else
@@ -769,6 +803,9 @@ static const struct of_device_id wiz_id_table[] = {
 	{
 		.compatible = "ti,j721e-wiz-10g", .data = (void *)J721E_WIZ_10G
 	},
+	{
+		.compatible = "ti,am64-wiz-10g", .data = (void *)AM64_WIZ_10G
+	},
 	{}
 };
 MODULE_DEVICE_TABLE(of, wiz_id_table);
@@ -904,14 +941,14 @@ static int wiz_probe(struct platform_device *pdev)
 	wiz->dev = dev;
 	wiz->regmap = regmap;
 	wiz->num_lanes = num_lanes;
-	if (wiz->type == J721E_WIZ_10G)
+	if (wiz->type == J721E_WIZ_10G || wiz->type == AM64_WIZ_10G)
 		wiz->clk_mux_sel = clk_mux_sel_10g;
 	else
 		wiz->clk_mux_sel = clk_mux_sel_16g;
 
 	wiz->clk_div_sel = clk_div_sel;
 
-	if (wiz->type == J721E_WIZ_10G)
+	if (wiz->type == J721E_WIZ_10G || wiz->type == AM64_WIZ_10G)
 		wiz->clk_div_sel_num = WIZ_DIV_NUM_CLOCKS_10G;
 	else
 		wiz->clk_div_sel_num = WIZ_DIV_NUM_CLOCKS_16G;
Signature · 1 line
2.17.1
Signature · 1 line
~Vinod
maintainer
#15 lore raw

Re: [PATCH 6/7] phy: ti: j721e-wiz: Enable reference clock output in cmn_refclk_<p/m>

In reply to Kishon Vijay Abraham I
Quoted 74 lines · Kishon Vijay Abraham I

cmn_refclk_<p/m> lines in Torrent SERDES is used for connecting external reference clock. cmn_refclk_<p/m> can also be configured to output the reference clock. In order to drive the refclk out from the SERDES (Cadence Torrent), PHY_EN_REFCLK should be set in SERDES_RST of WIZ. Model PHY_EN_REFCLK as a clock, so that platforms like AM642 EVM can enable it.

---
 drivers/phy/ti/phy-j721e-wiz.c | 115 +++++++++++++++++++++++++++++++++
 1 file changed, 115 insertions(+)
drivers/phy/ti/phy-j721e-wiz.c +30 -0
index 08acfab1ebe6..d60a9a01a8b2 100644
@@ -54,6 +54,7 @@ enum wiz_refclk_div_sel {
 
 static const struct reg_field por_en = REG_FIELD(WIZ_SERDES_CTRL, 31, 31);
 static const struct reg_field phy_reset_n = REG_FIELD(WIZ_SERDES_RST, 31, 31);
+static const struct reg_field phy_en_refclk = REG_FIELD(WIZ_SERDES_RST, 30, 30);
 static const struct reg_field pll1_refclk_mux_sel =
 					REG_FIELD(WIZ_SERDES_RST, 29, 29);
 static const struct reg_field pll0_refclk_mux_sel =
@@ -141,6 +142,15 @@ struct wiz_clk_div_sel {
 	const char		*node_name;
 };
 
+struct wiz_phy_en_refclk {
+	struct clk_hw		hw;
+	struct regmap_field	*phy_en_refclk;
+	struct clk_init_data	clk_data;
+};
+
+#define to_wiz_phy_en_refclk(_hw)	\
+			container_of(_hw, struct wiz_phy_en_refclk, hw)
+
 static struct wiz_clk_mux_sel clk_mux_sel_16g[] = {
 	{
 		/*
@@ -214,6 +224,7 @@ struct wiz {
 	unsigned int		clk_div_sel_num;
 	struct regmap_field	*por_en;
 	struct regmap_field	*phy_reset_n;
+	struct regmap_field	*phy_en_refclk;
 	struct regmap_field	*p_enable[WIZ_MAX_LANES];
 	struct regmap_field	*p_align[WIZ_MAX_LANES];
 	struct regmap_field	*p_raw_auto_start[WIZ_MAX_LANES];
@@ -450,9 +461,96 @@ static int wiz_regfield_init(struct wiz *wiz)
 		return PTR_ERR(wiz->typec_ln10_swap);
 	}
 
+	wiz->phy_en_refclk = devm_regmap_field_alloc(dev, regmap,
+						     phy_en_refclk);
+	if (IS_ERR(wiz->phy_en_refclk)) {
+		dev_err(dev, "PHY_EN_REFCLK reg field init failed\n");
+		return PTR_ERR(wiz->phy_en_refclk);
+	}
+
 	return 0;
 }
 
+static int wiz_phy_en_refclk_enable(struct clk_hw *hw)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk = to_wiz_phy_en_refclk(hw);
+	struct regmap_field *phy_en_refclk = wiz_phy_en_refclk->phy_en_refclk;
+
+	regmap_field_write(phy_en_refclk, 1);
+
+	return 0;
+}
+
+static void wiz_phy_en_refclk_disable(struct clk_hw *hw)
+{

drivers/phy/ti/phy-j721e-wiz.c static int wiz_regfield_init(struct wiz *wiz) · line 495

Quoted 10 lines
drivers/phy/ti/phy-j721e-wiz.c +10 -0
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk = to_wiz_phy_en_refclk(hw);
+	struct regmap_field *phy_en_refclk = wiz_phy_en_refclk->phy_en_refclk;
+
+	regmap_field_write(phy_en_refclk, 0);
+}
+
+static int wiz_phy_en_refclk_is_enabled(struct clk_hw *hw)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk = to_wiz_phy_en_refclk(hw);
+	struct regmap_field *phy_en_refclk = wiz_phy_en_refclk->phy_en_refclk;

get_phy_wiz_regmap() macro for this repeated patter..?

Quoted 17 lines
drivers/phy/ti/phy-j721e-wiz.c +17 -0
+	int val;
+
+	regmap_field_read(phy_en_refclk, &val);
+
+	return !!val;
+}
+
+static const struct clk_ops wiz_phy_en_refclk_ops = {
+	.enable = wiz_phy_en_refclk_enable,
+	.disable = wiz_phy_en_refclk_disable,
+	.is_enabled = wiz_phy_en_refclk_is_enabled,
+};
+
+static int wiz_phy_en_refclk_register(struct wiz *wiz, struct device_node *node,
+				      struct regmap_field *phy_en_refclk)
+{
+	struct wiz_phy_en_refclk *wiz_phy_en_refclk;

drivers/phy/ti/phy-j721e-wiz.c static int wiz_regfield_init(struct wiz *wiz) · line 522

Quoted 10 lines
drivers/phy/ti/phy-j721e-wiz.c +10 -0
+	struct device *dev = wiz->dev;
+	struct clk_init_data *init;
+	unsigned int num_parents;
+	const char *parent_name;
+	char clk_name[100];
+	struct clk *clk;
+	int ret;
+
+	wiz_phy_en_refclk = devm_kzalloc(dev, sizeof(*wiz_phy_en_refclk),
+					 GFP_KERNEL);

single line :)

drivers/phy/ti/phy-j721e-wiz.c static int wiz_regfield_init(struct wiz *wiz) · line 530

Quoted 8 lines
drivers/phy/ti/phy-j721e-wiz.c +8 -0
+	if (!wiz_phy_en_refclk)
+		return -ENOMEM;
+
+	num_parents = of_clk_get_parent_count(node);
+	parent_name = of_clk_get_parent_name(node, 0);
+
+	snprintf(clk_name, sizeof(clk_name), "%s_%s", dev_name(dev),
+		 node->name);

here too and few other places

Quoted 59 lines
drivers/phy/ti/phy-j721e-wiz.c +40 -0
+
+	init = &wiz_phy_en_refclk->clk_data;
+
+	init->ops = &wiz_phy_en_refclk_ops;
+	init->flags = 0;
+	init->parent_names = parent_name ? &parent_name : NULL;
+	init->num_parents = num_parents ? 1 : 0;
+	init->name = clk_name;
+
+	wiz_phy_en_refclk->phy_en_refclk = phy_en_refclk;
+	wiz_phy_en_refclk->hw.init = init;
+
+	clk = devm_clk_register(dev, &wiz_phy_en_refclk->hw);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ret = of_clk_add_provider(node, of_clk_src_simple_get, clk);
+	if (ret)
+		dev_err(dev, "Fail to add clock provider: %s\n", clk_name);
+
+	return ret;
+}
+
 static u8 wiz_clk_mux_get_parent(struct clk_hw *hw)
 {
 	struct wiz_clk_mux *mux = to_wiz_clk_mux(hw);
@@ -713,6 +811,20 @@ static int wiz_clock_init(struct wiz *wiz, struct device_node *node)
 		of_node_put(clk_node);
 	}
 
+	clk_node = of_get_child_by_name(node, "phy-en-refclk");
+	if (clk_node) {
+		ret = wiz_phy_en_refclk_register(wiz, clk_node,
+						 wiz->phy_en_refclk);
+		if (ret) {
+			dev_err(dev, "Failed to register %s clock\n",
+				node_name);
+			of_node_put(clk_node);
+			goto err;
+		}
+
+		of_node_put(clk_node);
+	}
+
 	return 0;
 err:
 	wiz_clock_cleanup(wiz, node);
@@ -828,6 +940,9 @@ static int wiz_get_lane_phy_types(struct device *dev, struct wiz *wiz)
 		      of_node_name_eq(subnode, "link")))
 			continue;
 
+		if (!(of_node_name_eq(subnode, "link")))
+			continue;
+
 		ret = of_property_read_u32(subnode, "reg", &reg);
 		if (ret) {
 			dev_err(dev,
Signature · 1 line
2.17.1
Signature · 1 line
~Vinod