Skip to contentSkip to conversation

NVIDIA Tegra ARM32 device-tree improvements

PATCH Superseded Dmitry Osipenko 1 participant 15 messages Jan 21, 2021 – Jan 22, 2021

Subsystems (2)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#2 lore raw

PATCH 2/13 ARM: tegra: ventana: Support CPU thermal throttling

In reply to Dmitry Osipenko

Enable CPU thermal throttling on Tegra20 Ventana board.

---
 arch/arm/boot/dts/tegra20-ventana.dts | 41 +++++++++++++++++++++++++--
 1 file changed, 39 insertions(+), 2 deletions(-)
arch/arm/boot/dts/tegra20-ventana.dts +39 -2
index 02b94ed722d0..99a356c1ccec 100644
@@ -2,6 +2,7 @@
 /dts-v1/;
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "tegra20.dtsi"
 #include "tegra20-cpu-opp.dtsi"
 #include "tegra20-cpu-opp-microvolt.dtsi"
@@ -528,9 +529,10 @@ ldo_rtc {
 			};
 		};
 
-		temperature-sensor@4c {
+		nct1008: temperature-sensor@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
+			#thermal-sensor-cells = <1>;
 		};
 	};
 
@@ -614,11 +616,13 @@ cpus {
 		cpu0: cpu@0 {
 			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -716,4 +720,37 @@ sound {
 			 <&tegra_car TEGRA20_CLK_CDEV1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip0: cpu-alert0 {
+					/* start throttling at 50C */
+					temperature = <50000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: cpu-crit {
+					/* shut down at 60C */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
 };
Signature · 1 line
2.29.2
#3 lore raw

PATCH 3/13 ARM: tegra: cardhu: Support CPU frequency and voltage scaling on all board variants

In reply to Dmitry Osipenko

Enable CPU frequency and voltage scaling on all Tegra30 Cardhu board variants.

---
 arch/arm/boot/dts/tegra30-cardhu-a04.dts | 48 ------------------------
 arch/arm/boot/dts/tegra30-cardhu.dtsi    | 40 ++++++++++++++++++--
 2 files changed, 37 insertions(+), 51 deletions(-)
arch/arm/boot/dts/tegra30-cardhu-a04.dts +0 -48
index c1c0ca628af1..a11028b8b67b 100644
@@ -2,8 +2,6 @@
 /dts-v1/;
 
 #include "tegra30-cardhu.dtsi"
-#include "tegra30-cpu-opp.dtsi"
-#include "tegra30-cpu-opp-microvolt.dtsi"
 
 /* This dts file support the cardhu A04 and later versions of board */
 
@@ -92,50 +90,4 @@ vdd_bl2_reg: regulator@106 {
 		enable-active-high;
 		gpio = <&gpio TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
 	};
-
-	i2c@7000d000 {
-		pmic: tps65911@2d {
-			regulators {
-				vddctrl_reg: vddctrl {
-					regulator-min-microvolt = <800000>;
-					regulator-max-microvolt = <1125000>;
-					regulator-coupled-with = <&vddcore_reg>;
-					regulator-coupled-max-spread = <300000>;
-					regulator-max-step-microvolt = <100000>;
-
-					nvidia,tegra-cpu-regulator;
-				};
-			};
-		};
-
-		vddcore_reg: tps62361@60 {
-			regulator-coupled-with = <&vddctrl_reg>;
-			regulator-coupled-max-spread = <300000>;
-			regulator-max-step-microvolt = <100000>;
-
-			nvidia,tegra-core-regulator;
-		};
-	};
-
-	cpus {
-		cpu0: cpu@0 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@1 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@2 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@3 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
 };
arch/arm/boot/dts/tegra30-cardhu.dtsi +37 -3
index 788f16d2a0fa..309538bdcd66 100644
@@ -1,6 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
 #include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
 
 /**
  * This file contains common DT entry for all fab version of Cardhu.
@@ -273,9 +275,14 @@ vdd2_reg: vdd2 {
 
 				vddctrl_reg: vddctrl {
 					regulator-name = "vdd_cpu,vdd_sys";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
 					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				vio_reg: vio {
@@ -343,17 +350,22 @@ temperature-sensor@4c {
 			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
 		};
 
-		tps62361@60 {
+		vdd_core: tps62361@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
 
 			regulator-name = "tps62361-vout";
 			regulator-min-microvolt = <500000>;
 			regulator-max-microvolt = <1500000>;
+			regulator-coupled-with = <&vddctrl_reg>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
 			regulator-boot-on;
 			regulator-always-on;
 			ti,vsel0-state-high;
 			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
 		};
 	};
 
@@ -425,6 +437,28 @@ clk32k_in: clock@0 {
 		#clock-cells = <0>;
 	};
 
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu2: cpu@2 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu3: cpu@3 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+	};
+
 	panel: panel {
 		compatible = "chunghwa,claa101wb01";
 		ddc-i2c-bus = <&panelddc>;
Signature · 1 line
2.29.2
#5 lore raw

PATCH 5/13 ARM: tegra: paz00: Enable full voltage scaling ranges for CPU and Core domains

In reply to Dmitry Osipenko

Enable full voltage scaling ranges for CPU and Core power domains.

---
 arch/arm/boot/dts/tegra20-paz00.dts | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
arch/arm/boot/dts/tegra20-paz00.dts +7 -7
index 7e49112cd9a1..940a9f31cd86 100644
@@ -387,10 +387,10 @@ sys_reg: sys {
 
 				core_vdd_reg: sm0 {
 					regulator-name = "+1.2vs_sm0,vdd_core";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1225000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
 					regulator-coupled-with = <&rtc_vdd_reg &cpu_vdd_reg>;
-					regulator-coupled-max-spread = <170000 450000>;
+					regulator-coupled-max-spread = <170000 550000>;
 					regulator-always-on;
 
 					nvidia,tegra-core-regulator;
@@ -401,7 +401,7 @@ cpu_vdd_reg: sm1 {
 					regulator-min-microvolt = <750000>;
 					regulator-max-microvolt = <1100000>;
 					regulator-coupled-with = <&core_vdd_reg &rtc_vdd_reg>;
-					regulator-coupled-max-spread = <450000 450000>;
+					regulator-coupled-max-spread = <550000 550000>;
 					regulator-always-on;
 
 					nvidia,tegra-cpu-regulator;
@@ -425,10 +425,10 @@ ldo1 {
 
 				rtc_vdd_reg: ldo2 {
 					regulator-name = "+1.2vs_ldo2,vdd_rtc";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1225000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
 					regulator-coupled-with = <&core_vdd_reg &cpu_vdd_reg>;
-					regulator-coupled-max-spread = <170000 450000>;
+					regulator-coupled-max-spread = <170000 550000>;
 					regulator-always-on;
 
 					nvidia,tegra-rtc-regulator;
Signature · 1 line
2.29.2
#0 lore raw

cover NVIDIA Tegra ARM32 device-tree improvements

Hi,

This series is partially factored out from [1] since the DT patches could be applied separately. In addition I added couple more new patches and implemented suggestion given by Daniel Lezcano to [1], see "Specify all CPU cores as cooling devices" patches.

[1] https://patchwork.ozlabs.org/project/linux-tegra/list/?series=221130

Please note that this patchset enables voltage scaling for a few boards, but currently voltage scaling is limited in kernel by the regulator coupler drivers, so it's safe to change the device-trees. Voltage scaling will be fully unlocked once [1] will be merged.

Dmitry Osipenko (13):
ARM: tegra: ventana: Support CPU and Core voltage scaling
ARM: tegra: ventana: Support CPU thermal throttling
ARM: tegra: cardhu: Support CPU frequency and voltage scaling on all
board variants
ARM: tegra: cardhu: Support CPU thermal throttling
ARM: tegra: paz00: Enable full voltage scaling ranges for CPU and Core
domains
ARM: tegra: acer-a500: Enable core voltage scaling
ARM: tegra: acer-a500: Reduce thermal throttling hysteresis to 0.2C
ARM: tegra: acer-a500: Specify all CPU cores as cooling devices
ARM: tegra: acer-a500: Rename avdd to vdda of touchscreen node
ARM: tegra: nexus7: Specify all CPU cores as cooling devices
ARM: tegra: ouya: Specify all CPU cores as cooling devices
ARM: tegra: Specify CPU suspend OPP in device-tree
ARM: tegra: Specify memory suspend OPP in device-tree

 .../boot/dts/tegra124-peripherals-opp.dtsi    |  5 ++
 .../boot/dts/tegra20-acer-a500-picasso.dts    | 14 ++--
 arch/arm/boot/dts/tegra20-cpu-opp.dtsi        |  2 +
 arch/arm/boot/dts/tegra20-paz00.dts           | 14 ++--
 .../arm/boot/dts/tegra20-peripherals-opp.dtsi |  1 +
 arch/arm/boot/dts/tegra20-ventana.dts         | 78 ++++++++++++++---
 .../tegra30-asus-nexus7-grouper-common.dtsi   | 14 +++-
 arch/arm/boot/dts/tegra30-cardhu-a04.dts      | 48 -----------
 arch/arm/boot/dts/tegra30-cardhu.dtsi         | 83 ++++++++++++++++++-
 arch/arm/boot/dts/tegra30-cpu-opp.dtsi        |  3 +
 arch/arm/boot/dts/tegra30-ouya.dts            | 15 +++-
 .../arm/boot/dts/tegra30-peripherals-opp.dtsi |  3 +
 12 files changed, 196 insertions(+), 84 deletions(-)
Signature · 1 line
2.29.2
#1 lore raw

PATCH 1/13 ARM: tegra: ventana: Support CPU and Core voltage scaling

Support CPU and Core voltage scaling on Tegra20 Ventana board.

---
 arch/arm/boot/dts/tegra20-ventana.dts | 37 ++++++++++++++++++++-------
 1 file changed, 28 insertions(+), 9 deletions(-)
arch/arm/boot/dts/tegra20-ventana.dts +28 -9
index 055334ae3d28..02b94ed722d0 100644
@@ -4,6 +4,7 @@
 #include <dt-bindings/input/input.h>
 #include "tegra20.dtsi"
 #include "tegra20-cpu-opp.dtsi"
+#include "tegra20-cpu-opp-microvolt.dtsi"
 
 / {
 	model = "NVIDIA Tegra20 Ventana evaluation board";
@@ -420,18 +421,28 @@ sys_reg: sys {
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&rtc_vdd &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
 					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
 				};
 
-				sm1 {
+				vdd_cpu: sm1 {
 					regulator-name = "vdd_sm1,vdd_cpu";
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-coupled-with = <&vdd_core &rtc_vdd>;
+					regulator-coupled-max-spread = <550000 550000>;
 					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				sm2_reg: sm2 {
@@ -450,10 +461,16 @@ ldo1 {
 					regulator-always-on;
 				};
 
-				ldo2 {
+				rtc_vdd: ldo2 {
 					regulator-name = "vdd_ldo2,vdd_rtc";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&vdd_core &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-rtc-regulator;
 				};
 
 				ldo3 {
@@ -595,10 +612,12 @@ clk32k_in: clock@0 {
 
 	cpus {
 		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
 		cpu@1 {
+			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};
Signature · 1 line
2.29.2
#4 lore raw

PATCH 4/13 ARM: tegra: cardhu: Support CPU thermal throttling

In reply to Dmitry Osipenko

Enable CPU thermal throttling on Tegra30 Cardhu board.

---
 arch/arm/boot/dts/tegra30-cardhu.dtsi | 43 ++++++++++++++++++++++++++-
 1 file changed, 42 insertions(+), 1 deletion(-)
arch/arm/boot/dts/tegra30-cardhu.dtsi +42 -1
index 309538bdcd66..2dff14b87f3e 100644
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "tegra30.dtsi"
 #include "tegra30-cpu-opp.dtsi"
 #include "tegra30-cpu-opp-microvolt.dtsi"
@@ -342,12 +343,13 @@ ldo8_reg: ldo8 {
 			};
 		};
 
-		temperature-sensor@4c {
+		nct1008: temperature-sensor@4c {
 			compatible = "onnn,nct1008";
 			reg = <0x4c>;
 			vcc-supply = <&sys_3v3_reg>;
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
+			#thermal-sensor-cells = <1>;
 		};
 
 		vdd_core: tps62361@60 {
@@ -441,21 +443,25 @@ cpus {
 		cpu0: cpu@0 {
 			cpu-supply = <&vddctrl_reg>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
 			cpu-supply = <&vddctrl_reg>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 
 		cpu2: cpu@2 {
 			cpu-supply = <&vddctrl_reg>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu@3 {
 			cpu-supply = <&vddctrl_reg>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -638,6 +644,41 @@ sound {
 					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip0: cpu-alert0 {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: cpu-crit {
+					/* shut down at 60C */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
Signature · 1 line
2.29.2
#14 lore raw

PATCH 13/13 ARM: tegra: Specify memory suspend OPP in device-tree

In reply to Dmitry Osipenko

Specify memory suspend OPP in a device-tree, just for consistency. Now memory will always suspend on the same frequency.

---
 arch/arm/boot/dts/tegra124-peripherals-opp.dtsi | 5 +++++
 arch/arm/boot/dts/tegra20-peripherals-opp.dtsi  | 1 +
 arch/arm/boot/dts/tegra30-peripherals-opp.dtsi  | 3 +++
 3 files changed, 9 insertions(+)
arch/arm/boot/dts/tegra124-peripherals-opp.dtsi +5 -0
index 49d9420a3289..781ac8601030 100644
@@ -128,24 +128,28 @@ opp@204000000,800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0003>;
+			opp-suspend;
 		};
 
 		opp@204000000,950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0008>;
+			opp-suspend;
 		};
 
 		opp@204000000,1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0010>;
+			opp-suspend;
 		};
 
 		opp@204000000,1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0004>;
+			opp-suspend;
 		};
 
 		opp@264000000,800 {
@@ -360,6 +364,7 @@ opp@204000000 {
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <3264000>;
+			opp-suspend;
 		};
 
 		opp@264000000 {
arch/arm/boot/dts/tegra20-peripherals-opp.dtsi +1 -0
index b84afecea154..ef3ad2e5f270 100644
@@ -68,6 +68,7 @@ opp@216000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <216000000>;
 			opp-supported-hw = <0x000F>;
+			opp-suspend;
 		};
 
 		opp@300000000 {
arch/arm/boot/dts/tegra30-peripherals-opp.dtsi +3 -0
index cbe84d25e726..2c9780319725 100644
@@ -128,12 +128,14 @@ opp@204000000,1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0007>;
+			opp-suspend;
 		};
 
 		opp@204000000,1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0008>;
+			opp-suspend;
 		};
 
 		opp@333500000,1000 {
@@ -312,6 +314,7 @@ opp@204000000 {
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <1632000>;
+			opp-suspend;
 		};
 
 		opp@333500000 {
Signature · 1 line
2.29.2
#9 lore raw

PATCH 9/13 ARM: tegra: acer-a500: Rename avdd to vdda of touchscreen node

In reply to Dmitry Osipenko

Rename avdd supply to vdda of the touchscreen node. The old supply name was incorrect.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +1 -1
index 8a98e4a9d994..d852527db707 100644
@@ -449,7 +449,7 @@ touchscreen@4c {
 
 			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
 
-			avdd-supply = <&vdd_3v3_sys>;
+			vdda-supply = <&vdd_3v3_sys>;
 			vdd-supply  = <&vdd_3v3_sys>;
 
 			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
Signature · 1 line
2.29.2
#7 lore raw

PATCH 7/13 ARM: tegra: acer-a500: Reduce thermal throttling hysteresis to 0.2C

In reply to Dmitry Osipenko

The 2C hysteresis is a bit too high, although CPU never gets hot on A500. Nevertheless, let's reduce thermal throttling hysteresis to 0.2C, which is a much more reasonable value.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +1 -1
index 8531abf329c6..64a303cc5395 100644
@@ -1058,7 +1058,7 @@ trips {
 				trip0: cpu-alert0 {
 					/* start throttling at 50C */
 					temperature = <50000>;
-					hysteresis = <3000>;
+					hysteresis = <200>;
 					type = "passive";
 				};
 
Signature · 1 line
2.29.2
#8 lore raw

PATCH 8/13 ARM: tegra: acer-a500: Specify all CPU cores as cooling devices

In reply to Dmitry Osipenko

If CPU0 is unplugged the cooling device can not rebind to CPU1. And if CPU0 is plugged in again, the cooling device may fail to initialize.

If the CPUs are mapped with the physical CPU0 to Linux numbering CPU1, the cooling device mapping will fail.

Hence specify all CPU cores as a cooling devices in the device-tree.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +4 -2
index 64a303cc5395..8a98e4a9d994 100644
@@ -841,9 +841,10 @@ cpu0: cpu@0 {
 			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -1073,7 +1074,8 @@ trip1: cpu-crit {
 			cooling-maps {
 				map0 {
 					trip = <&trip0>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				};
 			};
 		};
Signature · 1 line
2.29.2
#6 lore raw

PATCH 6/13 ARM: tegra: acer-a500: Enable core voltage scaling

In reply to Dmitry Osipenko

Allow lower core voltages on Acer A500.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +2 -2
index 40c1bab22155..8531abf329c6 100644
@@ -578,7 +578,7 @@ sys_reg: sys {
 
 				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
-					regulator-min-microvolt = <1200000>;
+					regulator-min-microvolt = <950000>;
 					regulator-max-microvolt = <1300000>;
 					regulator-coupled-with = <&rtc_vdd &vdd_cpu>;
 					regulator-coupled-max-spread = <170000 550000>;
@@ -619,7 +619,7 @@ ldo1 {
 
 				rtc_vdd: ldo2 {
 					regulator-name = "vdd_ldo2,vdd_rtc";
-					regulator-min-microvolt = <1200000>;
+					regulator-min-microvolt = <950000>;
 					regulator-max-microvolt = <1300000>;
 					regulator-coupled-with = <&vdd_core &vdd_cpu>;
 					regulator-coupled-max-spread = <170000 550000>;
Signature · 1 line
2.29.2
#12 lore raw

PATCH 11/13 ARM: tegra: ouya: Specify all CPU cores as cooling devices

In reply to Dmitry Osipenko

If CPU0 is unplugged the cooling device can not rebind to CPU1. And if CPU0 is plugged in again, the cooling device may fail to initialize.

If the CPUs are mapped with the physical CPU0 to Linux numbering CPU1, the cooling device mapping will fail.

Hence specify all CPU cores as a cooling devices in the device-tree.

---
 arch/arm/boot/dts/tegra30-ouya.dts | 15 +++++++++++----
 1 file changed, 11 insertions(+), 4 deletions(-)
arch/arm/boot/dts/tegra30-ouya.dts +11 -4
index 8f66b16a786f..faeccc301368 100644
@@ -392,19 +392,23 @@ cpu0: cpu@0 {
 			cpu-supply = <&vdd_cpu>;
 			#cooling-cells = <2>;
 		};
-		cpu@1 {
+
+		cpu1: cpu@1 {
 			operating-points-v2 = <&cpu0_opp_table>;
 			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			operating-points-v2 = <&cpu0_opp_table>;
 			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			operating-points-v2 = <&cpu0_opp_table>;
 			cpu-supply = <&vdd_cpu>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -456,7 +460,10 @@ map0 {
 				};
 				map1 {
 					trip = <&cpu_alert1>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				};
 			};
 		};
Signature · 1 line
2.29.2
#13 lore raw

PATCH 12/13 ARM: tegra: Specify CPU suspend OPP in device-tree

In reply to Dmitry Osipenko

Specify CPU suspend OPP in a device-tree, just for consistency. Now CPU will always suspend on the same frequency.

---
 arch/arm/boot/dts/tegra20-cpu-opp.dtsi | 2 ++
 arch/arm/boot/dts/tegra30-cpu-opp.dtsi | 3 +++
 2 files changed, 5 insertions(+)
arch/arm/boot/dts/tegra20-cpu-opp.dtsi +2 -0
index 702a635e88e7..135de316383b 100644
@@ -9,12 +9,14 @@ opp@216000000,750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0003>;
 			opp-hz = /bits/ 64 <216000000>;
+			opp-suspend;
 		};
 
 		opp@216000000,800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0004>;
 			opp-hz = /bits/ 64 <216000000>;
+			opp-suspend;
 		};
 
 		opp@312000000,750 {
arch/arm/boot/dts/tegra30-cpu-opp.dtsi +3 -0
index 0f7135006d19..72f2fe26cc0e 100644
@@ -45,18 +45,21 @@ opp@204000000,800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x31FE>;
 			opp-hz = /bits/ 64 <204000000>;
+			opp-suspend;
 		};
 
 		opp@204000000,850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0C01>;
 			opp-hz = /bits/ 64 <204000000>;
+			opp-suspend;
 		};
 
 		opp@204000000,912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <204000000>;
+			opp-suspend;
 		};
 
 		opp@312000000,850 {
Signature · 1 line
2.29.2
#11 lore raw

PATCH 10/13 ARM: tegra: nexus7: Specify all CPU cores as cooling devices

In reply to Dmitry Osipenko

If CPU0 is unplugged the cooling device can not rebind to CPU1. And if CPU0 is plugged in again, the cooling device may fail to initialize.

If the CPUs are mapped with the physical CPU0 to Linux numbering CPU1, the cooling device mapping will fail.

Hence specify all CPU cores as a cooling devices in the device-tree.

---
 .../dts/tegra30-asus-nexus7-grouper-common.dtsi    | 14 ++++++++++----
 1 file changed, 10 insertions(+), 4 deletions(-)
arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi +10 -4
index ac1c1a63eb0e..dc773b1bf8ee 100644
@@ -1056,19 +1056,22 @@ cpu0: cpu@0 {
 			#cooling-cells = <2>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			cpu-supply = <&vdd_cpu>;
 			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -1281,7 +1284,10 @@ trip1: cpu-crit {
 			cooling-maps {
 				map0 {
 					trip = <&trip0>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
 				};
 			};
 		};
Signature · 1 line
2.29.2
#10 lore raw

Re: [PATCH v1 09/13] ARM: tegra: acer-a500: Rename avdd to vdda of touchscreen node

In reply to Dmitry Osipenko

21.01.2021 21:23, Dmitry Osipenko пишет:

Quoted 14 lines

Rename avdd supply to vdda of the touchscreen node. The old supply name was incorrect.

---
 arch/arm/boot/dts/tegra20-acer-a500-picasso.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +0 -0
index 8a98e4a9d994..d852527db707 100644

arch/arm/boot/dts/tegra20-acer-a500-picasso.dts touchscreen@4c { · line 455

Quoted 8 lines
arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +1 -1
@@ -449,7 +449,7 @@ touchscreen@4c {
 
 			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
 
-			avdd-supply = <&vdd_3v3_sys>;
+			vdda-supply = <&vdd_3v3_sys>;
 			vdd-supply  = <&vdd_3v3_sys>;
 
 			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;

This patch should have a merge conflict as I see now, since atmel,wakeup-method isn't upstreamed yet. I'll rebase patches in a more correct order and will make a v2.