Skip to contentSkip to conversation

dsa: add MT7530 GPIO support

PATCH Applied DENG Qingfang 6 participants 11 messages Jan 25, 2021 – Jan 26, 2021

Subsystems (7)
lore
Share & tools
lore
#0 lore raw

v2 cover dsa: add MT7530 GPIO support

MT7530's LED controller can be used as GPIO controller. Add support for it.

DENG Qingfang (2):
dt-bindings: net: dsa: add MT7530 GPIO controller binding
net: dsa: mt7530: MT7530 optional GPIO support

 .../devicetree/bindings/net/dsa/mt7530.txt    |   6 +
 drivers/net/dsa/mt7530.c                      | 110 ++++++++++++++++++
 drivers/net/dsa/mt7530.h                      |  20 ++++
 3 files changed, 136 insertions(+)
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#1 lore raw

PATCH v2 1/2 dt-bindings: net: dsa: add MT7530 GPIO controller binding

Add device tree binding to support MT7530 GPIO controller.

---
Changes v1 -> v2:
No changes.

 Documentation/devicetree/bindings/net/dsa/mt7530.txt | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/net/dsa/mt7530.txt +6 -0
index 560369efad6c..de04626a8e9d 100644
@@ -76,6 +76,12 @@ phy-mode must be set, see also example 2 below!
  * mt7621: phy-mode = "rgmii-txid";
  * mt7623: phy-mode = "rgmii";
 
+Optional properties:
+
+- gpio-controller: Boolean; if defined, MT7530's LED controller will run on
+	GPIO mode.
+- #gpio-cells: Must be 2 if gpio-controller is defined.
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required, optional properties and how the integrated switch subnodes must
 be specified.
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
#6 lore raw

PATCH v2 2/2 net: dsa: mt7530: MT7530 optional GPIO support

In reply to DENG Qingfang

MT7530's LED controller can drive up to 15 LED/GPIOs.

Add support for GPIO control and allow users to use its GPIOs by setting gpio-controller property in device tree.

---
Changes v1 -> v2:

Set Output Enable after changing direction to output to avoid signal glitch.
Comment mt7530_gpio_to_bit function.

 drivers/net/dsa/mt7530.c | 110 +++++++++++++++++++++++++++++++++++++++
 drivers/net/dsa/mt7530.h |  20 +++++++
 2 files changed, 130 insertions(+)
drivers/net/dsa/mt7530.c +110 -0
index d2196197d920..eb13ba79dd01 100644
@@ -18,6 +18,7 @@
 #include <linux/regulator/consumer.h>
 #include <linux/reset.h>
 #include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
 #include <net/dsa.h>
 
 #include "mt7530.h"
@@ -1622,6 +1623,109 @@ mtk_get_tag_protocol(struct dsa_switch *ds, int port,
 	}
 }
 
+static inline u32
+mt7530_gpio_to_bit(unsigned int offset)
+{
+	/* Map GPIO offset to register bit
+	 * [ 2: 0]  port 0 LED 0..2 as GPIO 0..2
+	 * [ 6: 4]  port 1 LED 0..2 as GPIO 3..5
+	 * [10: 8]  port 2 LED 0..2 as GPIO 6..8
+	 * [14:12]  port 3 LED 0..2 as GPIO 9..11
+	 * [18:16]  port 4 LED 0..2 as GPIO 12..14
+	 */
+	return BIT(offset + offset / 3);
+}
+
+static int
+mt7530_gpio_get(struct gpio_chip *gc, unsigned int offset)
+{
+	struct mt7530_priv *priv = gpiochip_get_data(gc);
+	u32 bit = mt7530_gpio_to_bit(offset);
+
+	return !!(mt7530_read(priv, MT7530_LED_GPIO_DATA) & bit);
+}
+
+static void
+mt7530_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	struct mt7530_priv *priv = gpiochip_get_data(gc);
+	u32 bit = mt7530_gpio_to_bit(offset);
+
+	if (value)
+		mt7530_set(priv, MT7530_LED_GPIO_DATA, bit);
+	else
+		mt7530_clear(priv, MT7530_LED_GPIO_DATA, bit);
+}
+
+static int
+mt7530_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	struct mt7530_priv *priv = gpiochip_get_data(gc);
+	u32 bit = mt7530_gpio_to_bit(offset);
+
+	return (mt7530_read(priv, MT7530_LED_GPIO_DIR) & bit) ?
+		GPIO_LINE_DIRECTION_OUT : GPIO_LINE_DIRECTION_IN;
+}
+
+static int
+mt7530_gpio_direction_input(struct gpio_chip *gc, unsigned int offset)
+{
+	struct mt7530_priv *priv = gpiochip_get_data(gc);
+	u32 bit = mt7530_gpio_to_bit(offset);
+
+	mt7530_clear(priv, MT7530_LED_GPIO_OE, bit);
+	mt7530_clear(priv, MT7530_LED_GPIO_DIR, bit);
+
+	return 0;
+}
+
+static int
+mt7530_gpio_direction_output(struct gpio_chip *gc, unsigned int offset, int value)
+{
+	struct mt7530_priv *priv = gpiochip_get_data(gc);
+	u32 bit = mt7530_gpio_to_bit(offset);
+
+	mt7530_set(priv, MT7530_LED_GPIO_DIR, bit);
+
+	if (value)
+		mt7530_set(priv, MT7530_LED_GPIO_DATA, bit);
+	else
+		mt7530_clear(priv, MT7530_LED_GPIO_DATA, bit);
+
+	mt7530_set(priv, MT7530_LED_GPIO_OE, bit);
+
+	return 0;
+}
+
+static int
+mt7530_setup_gpio(struct mt7530_priv *priv)
+{
+	struct device *dev = priv->dev;
+	struct gpio_chip *gc;
+
+	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
+	if (!gc)
+		return -ENOMEM;
+
+	mt7530_write(priv, MT7530_LED_GPIO_OE, 0);
+	mt7530_write(priv, MT7530_LED_GPIO_DIR, 0);
+	mt7530_write(priv, MT7530_LED_IO_MODE, 0);
+
+	gc->label = "mt7530";
+	gc->parent = dev;
+	gc->owner = THIS_MODULE;
+	gc->get_direction = mt7530_gpio_get_direction;
+	gc->direction_input = mt7530_gpio_direction_input;
+	gc->direction_output = mt7530_gpio_direction_output;
+	gc->get = mt7530_gpio_get;
+	gc->set = mt7530_gpio_set;
+	gc->base = -1;
+	gc->ngpio = 15;
+	gc->can_sleep = true;
+
+	return devm_gpiochip_add_data(dev, gc, priv);
+}
+
 static int
 mt7530_setup(struct dsa_switch *ds)
 {
@@ -1763,6 +1867,12 @@ mt7530_setup(struct dsa_switch *ds)
 		}
 	}
 
+	if (of_property_read_bool(priv->dev->of_node, "gpio-controller")) {
+		ret = mt7530_setup_gpio(priv);
+		if (ret)
+			return ret;
+	}
+
 	mt7530_setup_port5(ds, interface);
 
 	/* Flush the FDB table */
drivers/net/dsa/mt7530.h +20 -0
index 32d8969b3ace..64a9bb377e15 100644
@@ -554,6 +554,26 @@ enum mt7531_clk_skew {
 #define  MT7531_GPIO12_RG_RXD3_MASK	GENMASK(19, 16)
 #define  MT7531_EXT_P_MDIO_12		(2 << 16)
 
+/* Registers for LED GPIO control (MT7530 only)
+ * All registers follow this pattern:
+ * [ 2: 0]  port 0
+ * [ 6: 4]  port 1
+ * [10: 8]  port 2
+ * [14:12]  port 3
+ * [18:16]  port 4
+ */
+
+/* LED enable, 0: Disable, 1: Enable (Default) */
+#define MT7530_LED_EN			0x7d00
+/* LED mode, 0: GPIO mode, 1: PHY mode (Default) */
+#define MT7530_LED_IO_MODE		0x7d04
+/* GPIO direction, 0: Input, 1: Output */
+#define MT7530_LED_GPIO_DIR		0x7d10
+/* GPIO output enable, 0: Disable, 1: Enable */
+#define MT7530_LED_GPIO_OE		0x7d14
+/* GPIO value, 0: Low, 1: High */
+#define MT7530_LED_GPIO_DATA		0x7d18
+
 #define MT7530_CREV			0x7ffc
 #define  CHIP_NAME_SHIFT		16
 #define  MT7530_ID			0x7530
Signature · 7 lines
2.25.1


_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
Reviewed-by on v2 2/2
#7 lore raw

Re: [PATCH net-next v2 2/2] net: dsa: mt7530: MT7530 optional GPIO support

Quoted 6 lines · DENG Qingfang

MT7530's LED controller can drive up to 15 LED/GPIOs.

Add support for GPIO control and allow users to use its GPIOs by setting gpio-controller property in device tree.

Yours,
Linus Walleij

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Reviewed-by on v2 1/2
#2 lore raw

Re: [PATCH net-next v2 1/2] dt-bindings: net: dsa: add MT7530 GPIO controller binding

In reply to DENG Qingfang
Quoted 3 lines · DENG Qingfang

Add device tree binding to support MT7530 GPIO controller.

Yours,
Linus Walleij

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

maintainer Reviewed-by on v2 1/2
#3 lore raw

Re: [PATCH net-next v2 1/2] dt-bindings: net: dsa: add MT7530 GPIO controller binding

In reply to DENG Qingfang
Quoted 3 lines · DENG Qingfang

Add device tree binding to support MT7530 GPIO controller.

Andrew

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

maintainer Reviewed-by on v2 2/2
#8 lore raw

Re: [PATCH net-next v2 2/2] net: dsa: mt7530: MT7530 optional GPIO support

In reply to DENG Qingfang
Quoted 6 lines · DENG Qingfang

MT7530's LED controller can drive up to 15 LED/GPIOs.

Add support for GPIO control and allow users to use its GPIOs by setting gpio-controller property in device tree.

Andrew

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

maintainer
#4 lore raw

Re: [PATCH net-next v2 1/2] dt-bindings: net: dsa: add MT7530 GPIO controller binding

In reply to DENG Qingfang
Quoted 10 lines · DENG Qingfang

Add device tree binding to support MT7530 GPIO controller.

---
Changes v1 -> v2:
No changes.

 Documentation/devicetree/bindings/net/dsa/mt7530.txt | 6 ++++++
 1 file changed, 6 insertions(+)

Please add Acked-by/Reviewed-by tags when posting new versions. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for acks received on the version they apply.

If a tag was not added on purpose, please state why and what changed.

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

#5 lore raw

Re: [PATCH net-next v2 1/2] dt-bindings: net: dsa: add MT7530 GPIO controller binding

Quoted 4 lines · Rob Herring

Please add Acked-by/Reviewed-by tags when posting new versions. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for acks received on the version they apply.

Sorry. Will do that next time.

Quoted 3 lines

If a tag was not added on purpose, please state why and what changed.

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

maintainer Applied
#9 lore raw
In reply to DENG Qingfang
Quoted 2 lines · On Mon, 25 Jan 2021 12:43:20 +0800 DENG Qingfang wrote:

MT7530's LED controller can be used as GPIO controller. Add support for it.

I added back Rob's tag and all the missing tags which patchwork did not register. Damn thing is really flaky right now. Anyway..

Applied, thanks everyone!

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek

#10 lore raw
In reply to DENG Qingfang
This series was applied to netdev/net-next.git (refs/heads/master):

Hello:

This series was applied to netdev/net-next.git (refs/heads/master):

Quoted 8 lines · On Mon, 25 Jan 2021 12:43:20 +0800 you wrote:

MT7530's LED controller can be used as GPIO controller. Add support for it.

DENG Qingfang (2):
dt-bindings: net: dsa: add MT7530 GPIO controller binding
net: dsa: mt7530: MT7530 optional GPIO support

[...]

Here is the summary with links:
- [net-next,v2,1/2] dt-bindings: net: dsa: add MT7530 GPIO controller binding

    https://git.kernel.org/netdev/net-next/c/974d5ba60df7
  - [net-next,v2,2/2] net: dsa: mt7530: MT7530 optional GPIO support
    https://git.kernel.org/netdev/net-next/c/429a0edeefd8

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html

_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek