mmc: Try power cycling card if command request times out
PATCH 1/1 mmc: Try power cycling card if command request times out
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?
drivers/mmc/core/block.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-)
drivers/mmc/core/block.c +18 -2
@@ -976,6 +976,7 @@ static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)*/ static void mmc_blk_issue_drv_op (struct mmc_queue *mq,struct request *req) { +int type =rq_data_dir (req) ==READ ?MMC_BLK_READ :MMC_BLK_WRITE ;struct mmc_queue_req *mq_rq;struct mmc_card *card = mq->card;struct mmc_blk_data *md = mq->blkdata;
@@ -983,7 +984,7 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)bool rpmb_ioctl;u8 **ext_csd;u32 status; -int ret; +int ret, retry =1 ;int i; mq_rq =req_to_mmc_queue_req (req);
@@ -994,9 +995,24 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)case MMC_DRV_OP_IOCTL_RPMB : idata = mq_rq->drv_op_data;for (i =0 , ret =0 ; i < mq_rq->ioc_count; i++) { +cmd_do: ret =__mmc_blk_ioctl_cmd (card, md, idata[i]); -if (ret) +if (ret == -ETIMEDOUT ) { +dev_warn (mmc_dev (card->host), +"error %d sending command\n" , ret); +cmd_reset: +mmc_blk_reset_success (md, type); +if (retry--) { +dev_warn (mmc_dev (card->host), +"power cycling card\n" ); +if (mmc_blk_reset + (md, card->host, type)) + goto cmd_reset; +mmc_blk_reset_success (md, type); + goto cmd_do; + }break ; + } }/* Always switch back to main area after RPMB access */ if (rpmb_ioctl)
Signature · 1 line
2.11.0
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 10 lines
Signed-off-by Mårten Lindahl <[email protected]>---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?
Maybe, it's a good idea to allow the similar reset for ioctls as we do for regular I/O requests. My concern with this though, is that we might allow user space to trigger a HW resets a bit too easily - and that could damage the card.
Did you consider this?
Quoted 52 lines
drivers/mmc/core/block.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-)drivers/mmc/core/block.c +18
-3@@ -976,6 +976,7 @@ static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)*/ static void mmc_blk_issue_drv_op (struct mmc_queue *mq,struct request *req) { +int type =rq_data_dir (req) ==READ ?MMC_BLK_READ :MMC_BLK_WRITE ;struct mmc_queue_req *mq_rq;struct mmc_card *card = mq->card;struct mmc_blk_data *md = mq->blkdata;@@ -983,7 +984,7 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)bool rpmb_ioctl;u8 **ext_csd;u32 status; -int ret; +int ret, retry =1 ;int i; mq_rq =req_to_mmc_queue_req (req);@@ -994,9 +995,24 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)case MMC_DRV_OP_IOCTL_RPMB : idata = mq_rq->drv_op_data;for (i =0 , ret =0 ; i < mq_rq->ioc_count; i++) { +cmd_do: ret =__mmc_blk_ioctl_cmd (card, md, idata[i]); -if (ret) +if (ret == -ETIMEDOUT ) { +dev_warn (mmc_dev (card->host), +"error %d sending command\n" , ret); +cmd_reset: +mmc_blk_reset_success (md, type); +if (retry--) { +dev_warn (mmc_dev (card->host), +"power cycling card\n" ); +if (mmc_blk_reset + (md, card->host, type)) + goto cmd_reset; +mmc_blk_reset_success (md, type); + goto cmd_do; + }break ; + } }/* Always switch back to main area after RPMB access */ if (rpmb_ioctl) --
Quoted 2 lines
2.11.0
Kind regards
Uffe
Quoted 70 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 10 lines
Signed-off-by Mårten Lindahl <[email protected]>---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?Maybe, it's a good idea to allow the similar reset for ioctls as we do for regular I/O requests. My concern with this though, is that we might allow user space to trigger a HW resets a bit too easily - and that could damage the card.
Did you consider this?
Quoted 24 lines
drivers/mmc/core/block.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-)drivers/mmc/core/block.c +2
-1@@ -976,6 +976,7 @@ static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)*/ static void mmc_blk_issue_drv_op (struct mmc_queue *mq,struct request *req) { +int type =rq_data_dir (req) ==READ ?MMC_BLK_READ :MMC_BLK_WRITE ;struct mmc_queue_req *mq_rq;struct mmc_card *card = mq->card;struct mmc_blk_data *md = mq->blkdata;@@ -983,7 +984,7 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)bool rpmb_ioctl;u8 **ext_csd;u32 status; -int ret; +int ret, retry =1 ;int i;
Quoted 3 lines
drivers/mmc/core/block.c static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req) · line 995
Quoted 3 lines
drivers/mmc/core/block.c +0
-0mq_rq =req_to_mmc_queue_req (req);@@ -994,9 +995,24 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)case MMC_DRV_OP_IOCTL_RPMB :
SD cards do not have RPMB. Did you mean eMMC?
Quoted 10 lines
drivers/mmc/core/block.c static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req) · line 1004
Quoted 10 lines
drivers/mmc/core/block.c +6
-1idata = mq_rq->drv_op_data;for (i =0 , ret =0 ; i < mq_rq->ioc_count; i++) { +cmd_do: ret =__mmc_blk_ioctl_cmd (card, md, idata[i]); -if (ret) +if (ret == -ETIMEDOUT ) { +dev_warn (mmc_dev (card->host), +"error %d sending command\n" , ret); +cmd_reset: +mmc_blk_reset_success (md, type);
mmc_blk_reset_success() is called upon success, not failure. The reset will not be attempted twice in a row, for a given type, without a "success" in between.
Quoted 21 lines
Quoted 15 lines
drivers/mmc/core/block.c +10
-1+if (retry--) { +dev_warn (mmc_dev (card->host), +"power cycling card\n" ); +if (mmc_blk_reset + (md, card->host, type)) + goto cmd_reset; +mmc_blk_reset_success (md, type); + goto cmd_do; + }break ; + } }/* Always switch back to main area after RPMB access */ if (rpmb_ioctl) --Quoted 2 lines
2.11.0
Kind regards
Uffe
Hi Adrian!
Thank you for your comments!
Quoted 71 lines · Adrian Hunter
Quoted 70 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 10 lines
Signed-off-by Mårten Lindahl <[email protected]>---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?Maybe, it's a good idea to allow the similar reset for ioctls as we do for regular I/O requests. My concern with this though, is that we might allow user space to trigger a HW resets a bit too easily - and that could damage the card.
Did you consider this?
Quoted 24 lines
drivers/mmc/core/block.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-)drivers/mmc/core/block.c +2
-1@@ -976,6 +976,7 @@ static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)*/ static void mmc_blk_issue_drv_op (struct mmc_queue *mq,struct request *req) { +int type =rq_data_dir (req) ==READ ?MMC_BLK_READ :MMC_BLK_WRITE ;struct mmc_queue_req *mq_rq;struct mmc_card *card = mq->card;struct mmc_blk_data *md = mq->blkdata;@@ -983,7 +984,7 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)bool rpmb_ioctl;u8 **ext_csd;u32 status; -int ret; +int ret, retry =1 ;int i;
Quoted 6 lines
Quoted 3 lines
drivers/mmc/core/block.c static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req) · line 995
Quoted 3 lines
drivers/mmc/core/block.c +0
-0mq_rq =req_to_mmc_queue_req (req);@@ -994,9 +995,24 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)case MMC_DRV_OP_IOCTL_RPMB :SD cards do not have RPMB. Did you mean eMMC?
No, you are right. This action should be excluded from 'case MMC_DRV_OP_IOCTL_RPMB'.
Quoted 16 lines
Quoted 11 lines
drivers/mmc/core/block.c static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req) · line 1004
Quoted 11 lines
drivers/mmc/core/block.c +6
-1idata = mq_rq->drv_op_data;for (i =0 , ret =0 ; i < mq_rq->ioc_count; i++) { +cmd_do: ret =__mmc_blk_ioctl_cmd (card, md, idata[i]); -if (ret) +if (ret == -ETIMEDOUT ) { +dev_warn (mmc_dev (card->host), +"error %d sending command\n" , ret); +cmd_reset: +mmc_blk_reset_success (md, type);
mmc_blk_reset_success()is called upon success, not failure. The reset will not be attempted twice in a row, for a given type, without a "success" in between.
Ok, yes I see. This line and the cmd_reset label should be removed, and if mmc_blk_reset fails we should break, not retry.
Kind regards
Mårten
Quoted 22 lines
Quoted 21 lines
Quoted 15 lines
drivers/mmc/core/block.c +10
-1+if (retry--) { +dev_warn (mmc_dev (card->host), +"power cycling card\n" ); +if (mmc_blk_reset + (md, card->host, type)) + goto cmd_reset; +mmc_blk_reset_success (md, type); + goto cmd_do; + }break ; + } }/* Always switch back to main area after RPMB access */ if (rpmb_ioctl) --Quoted 2 lines
2.11.0
Kind regards
Uffe
Hi Ulf!
Thank you for your comments!
Quoted 16 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 7 lines
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
Yes, that's correct. The problem we have seen is triggered by ioctls.
Quoted 5 lines
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Yes, we have tried that, and it does trigger a power cycle, making the card operational again. But as it requires an operator to trigger it, I thought it might be something that could be automated here. At least once.
Quoted 11 lines
Quoted 10 lines
Signed-off-by Mårten Lindahl <[email protected]>---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?
Quoted 7 lines
Maybe, it's a good idea to allow the similar reset for ioctls as we do for regular I/O requests. My concern with this though, is that we might allow user space to trigger a HW resets a bit too easily - and that could damage the card.
Did you consider this?
Yes, that is a valid point, and that is why the power cycle is only tried once. But the conditon for this reset is a -ETIMEDOUT, and this is the part of this patch where I am myself not sure of if it is enough to check for. Would this be an error that you could expect to happen with ioctl requests in other situations also, but not necessarily cause by a stalled card?
Kind regards
Mårten
Quoted 57 lines
Quoted 52 lines
drivers/mmc/core/block.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-)drivers/mmc/core/block.c +18
-3@@ -976,6 +976,7 @@ static inline void mmc_blk_reset_success(struct mmc_blk_data *md, int type)*/ static void mmc_blk_issue_drv_op (struct mmc_queue *mq,struct request *req) { +int type =rq_data_dir (req) ==READ ?MMC_BLK_READ :MMC_BLK_WRITE ;struct mmc_queue_req *mq_rq;struct mmc_card *card = mq->card;struct mmc_blk_data *md = mq->blkdata;@@ -983,7 +984,7 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)bool rpmb_ioctl;u8 **ext_csd;u32 status; -int ret; +int ret, retry =1 ;int i; mq_rq =req_to_mmc_queue_req (req);@@ -994,9 +995,24 @@ static void mmc_blk_issue_drv_op(struct mmc_queue *mq, struct request *req)case MMC_DRV_OP_IOCTL_RPMB : idata = mq_rq->drv_op_data;for (i =0 , ret =0 ; i < mq_rq->ioc_count; i++) { +cmd_do: ret =__mmc_blk_ioctl_cmd (card, md, idata[i]); -if (ret) +if (ret == -ETIMEDOUT ) { +dev_warn (mmc_dev (card->host), +"error %d sending command\n" , ret); +cmd_reset: +mmc_blk_reset_success (md, type); +if (retry--) { +dev_warn (mmc_dev (card->host), +"power cycling card\n" ); +if (mmc_blk_reset + (md, card->host, type)) + goto cmd_reset; +mmc_blk_reset_success (md, type); + goto cmd_do; + }break ; + } }/* Always switch back to main area after RPMB access */ if (rpmb_ioctl) --Quoted 2 lines
2.11.0
Kind regards
Uffe
Quoted 38 lines · Marten Lindahl
Hi Ulf!
Thank you for your comments!
Quoted 16 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 7 lines
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
Yes, that's correct. The problem we have seen is triggered by ioctls.
Quoted 5 lines
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 3 lines
Yes, we have tried that, and it does trigger a power cycle, making the card operational again. But as it requires an operator to trigger it, I thought it might be something that could be automated here. At least once.
Not sure what you mean by operator here? In the end it's a userspace program running and I assume it can deal with error paths. :-)
In any case, I understand your point.
Quoted 17 lines
Quoted 17 lines
Quoted 11 lines
Signed-off-by Mårten Lindahl <[email protected]>---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?Maybe, it's a good idea to allow the similar reset for ioctls as we do for regular I/O requests. My concern with this though, is that we might allow user space to trigger a HW resets a bit too easily - and that could damage the card.
Quoted 8 lines
Quoted 2 lines
Did you consider this?
Yes, that is a valid point, and that is why the power cycle is only tried once. But the conditon for this reset is a
-ETIMEDOUT, and this is the part of this patch where I am myself not sure of if it is enough to check for. Would this be an error that you could expect to happen with ioctl requests in other situations also, but not necessarily cause by a stalled card?
Exactly.
Many different commands can get pushed down to the card through the mmc ioctl interface. It's difficult to know what error path we should pick, other than reporting and propagating the error codes.
[...]
Kind regards
Uffe
Hi Ulf! My apologies for the delay.
Quoted 39 lines · Ulf Hansson
Quoted 38 lines · Marten Lindahl
Hi Ulf!
Thank you for your comments!
Quoted 16 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 7 lines
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
Yes, that's correct. The problem we have seen is triggered by ioctls.
Quoted 5 lines
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 9 lines
Quoted 3 lines
Yes, we have tried that, and it does trigger a power cycle, making the card operational again. But as it requires an operator to trigger it, I thought it might be something that could be automated here. At least once.
Not sure what you mean by operator here? In the end it's a userspace program running and I assume it can deal with error paths. :-)
In any case, I understand your point.
Yes, we have a userspace program. So if the userspace program will try to restore the card in a situation such as the one we are trying to solve here, how shall it perform it? Is it expected that a ioctl CMD0 request should be enough, or is there any other support for a userspace program to reset the card?
If it falls on a ioctl command to reset the card, how do we handle the case where the ioctl times out anyway? Or is the only way for a userspace program to restore the card, to make a block transfer that fails?
Kind regards
Mårten
Quoted 36 lines
Quoted 17 lines
Quoted 17 lines
Quoted 11 lines
Signed-off-by Mårten Lindahl <[email protected]>---
Please note: This might not be the way we want to handle these cases, but at least it lets us start the discussion. In which cases should the mmc framework deal with error messages like ETIMEDOUT, and in which cases should it be handled by userspace?
The mmc framework tries to recover a failed block request (mmc_blk_mq_rw_recovery) which may end up in a HW reset of the card. Would it be an idea to act in a similar way when an ioctl times out?Maybe, it's a good idea to allow the similar reset for ioctls as we do for regular I/O requests. My concern with this though, is that we might allow user space to trigger a HW resets a bit too easily - and that could damage the card.
Quoted 8 lines
Quoted 2 lines
Did you consider this?
Yes, that is a valid point, and that is why the power cycle is only tried once. But the conditon for this reset is a
-ETIMEDOUT, and this is the part of this patch where I am myself not sure of if it is enough to check for. Would this be an error that you could expect to happen with ioctl requests in other situations also, but not necessarily cause by a stalled card?Exactly.
Many different commands can get pushed down to the card through the mmc ioctl interface. It's difficult to know what error path we should pick, other than reporting and propagating the error codes.
[...]
Kind regards
Uffe
Quoted 50 lines · Marten Lindahl
Hi Ulf! My apologies for the delay.
Quoted 46 lines · Ulf Hansson
Quoted 38 lines · Marten Lindahl
Hi Ulf!
Thank you for your comments!
Quoted 16 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 7 lines
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
Yes, that's correct. The problem we have seen is triggered by ioctls.
Quoted 5 lines
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 3 lines
Yes, we have tried that, and it does trigger a power cycle, making the card operational again. But as it requires an operator to trigger it, I thought it might be something that could be automated here. At least once.
Not sure what you mean by operator here? In the end it's a userspace program running and I assume it can deal with error paths. :-)
Quoted 8 lines
Quoted 2 lines
In any case, I understand your point.
Yes, we have a userspace program. So if the userspace program will try to restore the card in a situation such as the one we are trying to solve here, how shall it perform it? Is it expected that a ioctl CMD0 request should be enough, or is there any other support for a userspace program to reset the card?
Correct, there is no way for userspace to reset cards through an ioctl.
Quoted 4 lines
If it falls on a ioctl command to reset the card, how do we handle the case where the ioctl times out anyway? Or is the only way for a userspace program to restore the card, to make a block transfer that fails?
Yes, that is what I was thinking. According to the use case you have described, this should be possible for you to implement as a part of your userspace program, no?
[...]
Kind regards
Uffe
Quoted 63 lines · Ulf Hansson
Quoted 50 lines · Marten Lindahl
Hi Ulf! My apologies for the delay.
Quoted 46 lines · Ulf Hansson
Quoted 38 lines · Marten Lindahl
Hi Ulf!
Thank you for your comments!
Quoted 16 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 7 lines
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
Yes, that's correct. The problem we have seen is triggered by ioctls.
Quoted 5 lines
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 3 lines
Yes, we have tried that, and it does trigger a power cycle, making the card operational again. But as it requires an operator to trigger it, I thought it might be something that could be automated here. At least once.
Not sure what you mean by operator here? In the end it's a userspace program running and I assume it can deal with error paths. :-)
Quoted 8 lines
Quoted 2 lines
In any case, I understand your point.
Yes, we have a userspace program. So if the userspace program will try to restore the card in a situation such as the one we are trying to solve here, how shall it perform it? Is it expected that a ioctl CMD0 request should be enough, or is there any other support for a userspace program to reset the card?
Correct, there is no way for userspace to reset cards through an ioctl.
Quoted 1 line
Quoted 7 lines
Quoted 3 lines
If it falls on a ioctl command to reset the card, how do we handle the case where the ioctl times out anyway? Or is the only way for a userspace program to restore the card, to make a block transfer that fails?
Yes, that is what I was thinking. According to the use case you have described, this should be possible for you to implement as a part of your userspace program, no?
Ok, I will discuss that with the people maintaining the userspace program :)
But would it be of interest to review a patch introducing a more clean card reset request, without block transfers?
Kind regards
Mårten
Quoted 5 lines
[...]
Kind regards
Uffe
Quoted 69 lines · Marten Lindahl
Quoted 67 lines · Ulf Hansson
Quoted 50 lines · Marten Lindahl
Hi Ulf! My apologies for the delay.
Quoted 46 lines · Ulf Hansson
Quoted 38 lines · Marten Lindahl
Hi Ulf!
Thank you for your comments!
Quoted 16 lines · Ulf Hansson
+ Adrian
Quoted 13 lines · Mårten Lindahl
Sometimes SD cards that has been run for a long time enters a state where it cannot by itself be recovered, but needs a power cycle to be operational again. Card status analysis has indicated that the card can end up in a state where all external commands are ignored by the card since it is halted by data timeouts.
If the card has been heavily used for a long time it can be weared out, and should typically be replaced. But on some tests, it shows that the card can still be functional after a power cycle, but as it requires an operator to do it, the card can remain in a non-operational state for a long time until the problem has been observed by the operator.
Quoted 7 lines
Quoted 4 lines
This patch adds function to power cycle the card in case it does not respond to a command, and then resend the command if the power cycle was successful. This procedure will be tested 1 time before giving up, and resuming host operation as normal.
I assume the context above is all about the ioctl interface?
Yes, that's correct. The problem we have seen is triggered by ioctls.
Quoted 5 lines
So, when the card enters this non functional state, have you tried just reading a block through the regular I/O interface. Does it trigger a power cycle of the card - and then makes it functional again?
Quoted 3 lines
Yes, we have tried that, and it does trigger a power cycle, making the card operational again. But as it requires an operator to trigger it, I thought it might be something that could be automated here. At least once.
Not sure what you mean by operator here? In the end it's a userspace program running and I assume it can deal with error paths. :-)
Quoted 8 lines
Quoted 2 lines
In any case, I understand your point.
Yes, we have a userspace program. So if the userspace program will try to restore the card in a situation such as the one we are trying to solve here, how shall it perform it? Is it expected that a ioctl CMD0 request should be enough, or is there any other support for a userspace program to reset the card?
Correct, there is no way for userspace to reset cards through an ioctl.
Quoted 4 lines
If it falls on a ioctl command to reset the card, how do we handle the case where the ioctl times out anyway? Or is the only way for a userspace program to restore the card, to make a block transfer that fails?
Quoted 8 lines
Quoted 3 lines
Yes, that is what I was thinking. According to the use case you have described, this should be possible for you to implement as a part of your userspace program, no?
Ok, I will discuss that with the people maintaining the userspace program :)
But would it be of interest to review a patch introducing a more clean card reset request, without block transfers?
Well, if you can solve it with block transfers that's the preferred option, in my opinion.
As I stated earlier, my main issue with the HW reset through the ioctl interface, is that we don't know what combination of request/command/response we should be doing a reset for.
Kind regards
Uffe