mtd: spi-nor: support dumping sfdp tables
Subsystems (2)
RFC PATCH 1/3 mtd: spi-nor: support dumping sfdp tables
Add the possibility to dump the SFDP data of a flash device.
More and more flash devices share the same flash ID and we need per device fixups. Usually, these fixups differentiate flashes by looking at differences in the SFDP data. Determining the difference is only possible if we have the SFDP data for all the flashes which share a flash ID. This will lay the foundation to dump the whole SFDP data of a flash device.
This is even more important, because some datasheets doesn't even contain the SFDP data. Fixups for these kind of flashes are nearly impossible to do.
I envision having a database of all the SFDP data for the flashes we support and make it a requirement to submit it when a new flash is added. This might or might not have legal implications. Thus I'd start with having that database private to the SPI NOR maintainers.
There are two ways to provide access to the SFDP data:
(1) We just read the SFDP data once and cache it
(2) Any userspace access will always read the SFDP data
I choose (2) because it isn't as invasive as (1). The current SFDP code reads the SFDP data only partially and only the part which are actually used. Using (1) would mean to change that behavior.
Michael Walle (3):
mtd: spi-nor: sfdp: remember sfdp_size
mtd: spi-nor: sfdp: fix spi_nor_read_sfdp()
mtd: spi-nor: add sysfs and SFDP support
drivers/mtd/spi-nor/Makefile | 2 +- drivers/mtd/spi-nor/core.c | 5 +++ drivers/mtd/spi-nor/core.h | 3 ++ drivers/mtd/spi-nor/sfdp.c | 24 +++++++++++- drivers/mtd/spi-nor/sfdp.h | 2 + drivers/mtd/spi-nor/sysfs.c | 73 ++++++++++++++++++++++++++++++++++++ include/linux/mtd/spi-nor.h | 1 + 7 files changed, 107 insertions(+), 3 deletions(-) create mode 100644 drivers/mtd/spi-nor/sysfs.c
Signature · 6 lines
2.20.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
RFC PATCH 1/3 mtd: spi-nor: sfdp: remember sfdp_size
Save the sftp_size in the spi_nor struct so we can use it to dump the SFDP table without parsing the headers again.
--- drivers/mtd/spi-nor/sfdp.c | 12 ++++++++++++ include/linux/mtd/spi-nor.h | 1 + 2 files changed, 13 insertions(+)
drivers/mtd/spi-nor/sfdp.c +12 -0
@@ -16,6 +16,7 @@ (((p)->parameter_table_pointer[2 ] <<16 ) | \ ((p)->parameter_table_pointer[1 ] <<8 ) | \ ((p)->parameter_table_pointer[0] << 0)) +#define SFDP_PARAM_HEADER_PARAM_LEN (p) ((p)->length * 4)#define SFDP_BFPT_ID 0xff00/* Basic Flash Parameter Table */ #define SFDP_SECTOR_MAP_ID 0xff81/* Sector Map Table */
@@ -1263,6 +1264,7 @@ int spi_nor_parse_sfdp(struct spi_nor *nor,struct sfdp_parameter_header *param_headers =NULL ;struct sfdp_header header;struct device *dev = nor->dev; +size_t param_max_offset;size_t psize;int i, err;
@@ -1285,6 +1287,9 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, bfpt_header->major != SFDP_JESD216_MAJOR)return -EINVAL ; + nor->sfdp_size =SFDP_PARAM_HEADER_PTP (bfpt_header) + +SFDP_PARAM_HEADER_PARAM_LEN (bfpt_header); +/* * Allocate memory then read all parameter headers with a single * Read SFDP command. These parameter headers will actually be parsed
@@ -1311,6 +1316,13 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, } } +for (i =0 ; i < header.nph; i++) { + param_header = ¶m_headers[i]; + param_max_offset =SFDP_PARAM_HEADER_PTP (param_header) + +SFDP_PARAM_HEADER_PARAM_LEN (param_header); + nor->sfdp_size =max (nor->sfdp_size, param_max_offset); + } +/* * Check other parameter headers to get the latest revision of * the basic flash parameter table.
include/linux/mtd/spi-nor.h +1 -0
@@ -404,6 +404,7 @@ struct spi_nor {bool sst_write_second;u32 flags;enum spi_nor_cmd_ext cmd_ext_type; +size_t sfdp_size;const struct spi_nor_controller_ops *controller_ops;
Signature · 1 line
2.20.1
Re: [RFC PATCH 1/3] mtd: spi-nor: sfdp: remember sfdp_size
Quoted 40 lines · Michael Walle
Save the
sftp_sizein thespi_norstruct so we can use it to dump the SFDP table without parsing the headers again.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 12 ++++++++++++ include/linux/mtd/spi-nor.h | 1 + 2 files changed, 13 insertions(+)drivers/mtd/spi-nor/sfdp.c +5
-0@@ -16,6 +16,7 @@ (((p)->parameter_table_pointer[2 ] <<16 ) | \ ((p)->parameter_table_pointer[1 ] <<8 ) | \ ((p)->parameter_table_pointer[0] << 0)) +#define SFDP_PARAM_HEADER_PARAM_LEN (p) ((p)->length * 4)#define SFDP_BFPT_ID 0xff00/* Basic Flash Parameter Table */ #define SFDP_SECTOR_MAP_ID 0xff81/* Sector Map Table */ @@ -1263,6 +1264,7 @@ int spi_nor_parse_sfdp(struct spi_nor *nor,struct sfdp_parameter_header *param_headers =NULL ;struct sfdp_header header;struct device *dev = nor->dev; +size_t param_max_offset;size_t psize;int i, err;@@ -1285,6 +1287,9 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, bfpt_header->major != SFDP_JESD216_MAJOR)return -EINVAL ; + nor->sfdp_size =SFDP_PARAM_HEADER_PTP (bfpt_header) + +SFDP_PARAM_HEADER_PARAM_LEN (bfpt_header); +/* * Allocate memory then read all parameter headers with a single * Read SFDP command. These parameter headers will actually be parsed
drivers/mtd/spi-nor/sfdp.c int spi_nor_parse_sfdp(struct spi_nor *nor, · line 1325
Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c +7
-0@@ -1311,6 +1316,13 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, } } +for (i =0 ; i < header.nph; i++) { + param_header = ¶m_headers[i]; + param_max_offset =SFDP_PARAM_HEADER_PTP (param_header) + +SFDP_PARAM_HEADER_PARAM_LEN (param_header); + nor->sfdp_size =max (nor->sfdp_size, param_max_offset); + } +
I don't see any mention in the SFDP spec (JESD216D-01) that parameter tables have to be contiguous. In fact, it says that "Parameter tables may be located anywhere in the SFDP space. They do not need to immediately follow the parameter headers". But I guess we can just say the sysfs entry exports the entire SFDP space instead of just the tables so that is OK.
This patch looks good to me other than the small nitpick that we can merge this loop and the one below that tries to find the latest BFPT version.
include/linux/mtd/spi-nor.h struct spi_nor { · line 407
Quoted 12 lines
drivers/mtd/spi-nor/sfdp.c +0
-0/* * Check other parameter headers to get the latest revision of * the basic flash parameter table. include/linux/mtd/spi-nor.h +1
-0@@ -404,6 +404,7 @@ struct spi_nor {bool sst_write_second;u32 flags;enum spi_nor_cmd_ext cmd_ext_type; +size_t sfdp_size;
Documentation for this variable missing.
Quoted 6 lines
include/linux/mtd/spi-nor.h +0
-0const struct spi_nor_controller_ops *controller_ops;Signature · 1 line
2.20.1
Signature · 3 lines
Regards, Pratyush Yadav Texas Instruments Inc.
Re: [RFC PATCH 1/3] mtd: spi-nor: sfdp: remember sfdp_size
Hi Pratyush,
Am 2021-03-16 11:42, schrieb Pratyush Yadav:
Quoted 45 lines · Michael Walle
Quoted 44 lines
Save the
sftp_sizein thespi_norstruct so we can use it to dump the SFDP table without parsing the headers again.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 12 ++++++++++++ include/linux/mtd/spi-nor.h | 1 + 2 files changed, 13 insertions(+)drivers/mtd/spi-nor/sfdp.c +5
-0@@ -16,6 +16,7 @@ (((p)->parameter_table_pointer[2 ] <<16 ) | \ ((p)->parameter_table_pointer[1 ] <<8 ) | \ ((p)->parameter_table_pointer[0] << 0)) +#define SFDP_PARAM_HEADER_PARAM_LEN (p) ((p)->length * 4)#define SFDP_BFPT_ID 0xff00/* Basic Flash Parameter Table */ #define SFDP_SECTOR_MAP_ID 0xff81/* Sector Map Table */ @@ -1263,6 +1264,7 @@ int spi_nor_parse_sfdp(struct spi_nor *nor,struct sfdp_parameter_header *param_headers =NULL ;struct sfdp_header header;struct device *dev = nor->dev; +size_t param_max_offset;size_t psize;int i, err;@@ -1285,6 +1287,9 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, bfpt_header->major != SFDP_JESD216_MAJOR)return -EINVAL ; + nor->sfdp_size =SFDP_PARAM_HEADER_PTP (bfpt_header) + +SFDP_PARAM_HEADER_PARAM_LEN (bfpt_header); +/* * Allocate memory then read all parameter headers with a single * Read SFDP command. These parameter headers will actually be parsed
drivers/mtd/spi-nor/sfdp.c +0
-0@@ -1311,6 +1316,13 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, } }
Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c int spi_nor_parse_sfdp(struct spi_nor *nor, · line 1325
Quoted 7 lines
drivers/mtd/spi-nor/sfdp.c +7
-0+for (i =0 ; i < header.nph; i++) { + param_header = ¶m_headers[i]; + param_max_offset =SFDP_PARAM_HEADER_PTP (param_header) + +SFDP_PARAM_HEADER_PARAM_LEN (param_header); + nor->sfdp_size =max (nor->sfdp_size, param_max_offset); + } +I don't see any mention in the SFDP spec (JESD216D-01) that parameter tables have to be contiguous.
ch. 6.1, fig.10 looks like all the headers come after the initial SFDP header. If that wasn't the case, how would you find the headers then?
Also ch. 6.3
"""All subsequent parameter headers need to be contiguous and may be specified..."""
Quoted 3 lines
In fact, it says that "Parameter tables
may be located anywhere in the SFDP space. They do not need to immediately follow the parameter headers".
The tables itself, yes, but not the headers for the tables.
Quoted 7 lines
But I guess we can just say
the sysfs entry exports the entire SFDP space instead of just the tables so that is OK.This patch looks good to me other than the small nitpick that we can merge this loop and the one below that tries to find the latest BFPT version.
btw. I've also added an export for the jedec id and the flash name to this patch, which will be included in the next version.
Quoted 21 lines
include/linux/mtd/spi-nor.h struct spi_nor { · line 407
Quoted 12 lines
drivers/mtd/spi-nor/sfdp.c +0
-0/* * Check other parameter headers to get the latest revision of * the basic flash parameter table. include/linux/mtd/spi-nor.h +1
-0@@ -404,6 +404,7 @@ struct spi_nor {bool sst_write_second;u32 flags;enum spi_nor_cmd_ext cmd_ext_type; +size_t sfdp_size;Documentation for this variable missing.
Quoted 6 lines
include/linux/mtd/spi-nor.h +0
-1const struct spi_nor_controller_ops *controller_ops; --2.20.1
Signature · 5 lines
-michael ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [RFC PATCH 1/3] mtd: spi-nor: sfdp: remember sfdp_size
Quoted 66 lines · Michael Walle
Hi Pratyush,
Am 2021-03-16 11:42, schrieb Pratyush Yadav:
Quoted 45 lines · Michael Walle
Quoted 44 lines
Save the
sftp_sizein thespi_norstruct so we can use it to dump the SFDP table without parsing the headers again.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 12 ++++++++++++ include/linux/mtd/spi-nor.h | 1 + 2 files changed, 13 insertions(+)drivers/mtd/spi-nor/sfdp.c +5
-0@@ -16,6 +16,7 @@ (((p)->parameter_table_pointer[2 ] <<16 ) | \ ((p)->parameter_table_pointer[1 ] <<8 ) | \ ((p)->parameter_table_pointer[0] << 0)) +#define SFDP_PARAM_HEADER_PARAM_LEN (p) ((p)->length * 4)#define SFDP_BFPT_ID 0xff00/* Basic Flash Parameter Table */ #define SFDP_SECTOR_MAP_ID 0xff81/* Sector Map Table */ @@ -1263,6 +1264,7 @@ int spi_nor_parse_sfdp(struct spi_nor *nor,struct sfdp_parameter_header *param_headers =NULL ;struct sfdp_header header;struct device *dev = nor->dev; +size_t param_max_offset;size_t psize;int i, err;@@ -1285,6 +1287,9 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, bfpt_header->major != SFDP_JESD216_MAJOR)return -EINVAL ; + nor->sfdp_size =SFDP_PARAM_HEADER_PTP (bfpt_header) + +SFDP_PARAM_HEADER_PARAM_LEN (bfpt_header); +/* * Allocate memory then read all parameter headers with a single * Read SFDP command. These parameter headers will actually be parsed
drivers/mtd/spi-nor/sfdp.c +0
-0@@ -1311,6 +1316,13 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, } }Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c int spi_nor_parse_sfdp(struct spi_nor *nor, · line 1325
Quoted 7 lines
drivers/mtd/spi-nor/sfdp.c +7
-0+for (i =0 ; i < header.nph; i++) { + param_header = ¶m_headers[i]; + param_max_offset =SFDP_PARAM_HEADER_PTP (param_header) + +SFDP_PARAM_HEADER_PARAM_LEN (param_header); + nor->sfdp_size =max (nor->sfdp_size, param_max_offset); + } +I don't see any mention in the SFDP spec (JESD216D-01) that parameter tables have to be contiguous.
ch. 6.1, fig.10 looks like all the headers come after the initial SFDP header. If that wasn't the case, how would you find the headers then?
Also ch. 6.3
"""All subsequent parameter headers need to be contiguous and may be specified..."""
Quoted 5 lines
Quoted 3 lines
In fact, it says that "Parameter tables
may be located anywhere in the SFDP space. They do not need to immediately follow the parameter headers".The tables itself, yes, but not the headers for the tables.
Yes, I was talking about the tables and not the headers. There might be holes in the SFDP space but I don't think it would be a problem.
Signature · 7 lines
Regards, Pratyush Yadav Texas Instruments Inc. ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [RFC PATCH 1/3] mtd: spi-nor: sfdp: remember sfdp_size
Am 2021-03-16 12:06, schrieb Pratyush Yadav:
Quoted 67 lines · Michael Walle
Quoted 66 lines
Hi Pratyush,
Am 2021-03-16 11:42, schrieb Pratyush Yadav:
Quoted 45 lines · Michael Walle
Quoted 44 lines
Save the
sftp_sizein thespi_norstruct so we can use it to dump the SFDP table without parsing the headers again.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 12 ++++++++++++ include/linux/mtd/spi-nor.h | 1 + 2 files changed, 13 insertions(+)drivers/mtd/spi-nor/sfdp.c +5
-0@@ -16,6 +16,7 @@ (((p)->parameter_table_pointer[2 ] <<16 ) | \ ((p)->parameter_table_pointer[1 ] <<8 ) | \ ((p)->parameter_table_pointer[0] << 0)) +#define SFDP_PARAM_HEADER_PARAM_LEN (p) ((p)->length * 4)#define SFDP_BFPT_ID 0xff00/* Basic Flash Parameter Table */ #define SFDP_SECTOR_MAP_ID 0xff81/* Sector Map Table */ @@ -1263,6 +1264,7 @@ int spi_nor_parse_sfdp(struct spi_nor *nor,struct sfdp_parameter_header *param_headers =NULL ;struct sfdp_header header;struct device *dev = nor->dev; +size_t param_max_offset;size_t psize;int i, err;@@ -1285,6 +1287,9 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, bfpt_header->major != SFDP_JESD216_MAJOR)return -EINVAL ; + nor->sfdp_size =SFDP_PARAM_HEADER_PTP (bfpt_header) + +SFDP_PARAM_HEADER_PARAM_LEN (bfpt_header); +/* * Allocate memory then read all parameter headers with a single * Read SFDP command. These parameter headers will actually be parsed
drivers/mtd/spi-nor/sfdp.c +0
-0@@ -1311,6 +1316,13 @@ int spi_nor_parse_sfdp(struct spi_nor *nor, } }Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c int spi_nor_parse_sfdp(struct spi_nor *nor, · line 1325
Quoted 7 lines
drivers/mtd/spi-nor/sfdp.c +7
-0+for (i =0 ; i < header.nph; i++) { + param_header = ¶m_headers[i]; + param_max_offset =SFDP_PARAM_HEADER_PTP (param_header) + +SFDP_PARAM_HEADER_PARAM_LEN (param_header); + nor->sfdp_size =max (nor->sfdp_size, param_max_offset); + } +I don't see any mention in the SFDP spec (JESD216D-01) that parameter tables have to be contiguous.
ch. 6.1, fig.10 looks like all the headers come after the initial SFDP header. If that wasn't the case, how would you find the headers then?
Also ch. 6.3
"""All subsequent parameter headers need to be contiguous and may be specified..."""
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
In fact, it says that "Parameter tables
may be located anywhere in the SFDP space. They do not need to immediately follow the parameter headers".The tables itself, yes, but not the headers for the tables.
Yes, I was talking about the tables and not the headers. There might be holes in the SFDP space but I don't think it would be a problem.
Ah, ok. Well basically I'm assuming that the holes will returning some sane values. Or you could dump the space together with a mask. But that is overkill ;)
-michael
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
RFC PATCH 2/3 mtd: spi-nor: sfdp: fix spi_nor_read_sfdp()
In reply to Michael WalleIf spi_nor_read_sfdp() is used after probe, we have to set read_proto and the read dirmap.
--- drivers/mtd/spi-nor/sfdp.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/mtd/spi-nor/sfdp.c +8 -0
@@ -179,19 +179,27 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, size_t len, void *buf) { u8 addr_width, read_opcode, read_dummy; +struct spi_mem_dirmap_desc *rdesc; +enum spi_nor_protocol read_proto;int ret; read_opcode = nor->read_opcode; + read_proto = nor->read_proto; + rdesc = nor->dirmap.rdesc; addr_width = nor->addr_width; read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ; + nor->read_proto =SNOR_PROTO_1_1_1 ; + nor->dirmap.rdesc =NULL ; nor->addr_width =3 ; nor->read_dummy =8 ; ret =spi_nor_read_raw (nor, addr, len, buf); nor->read_opcode = read_opcode; + nor->read_proto = read_proto; + nor->dirmap.rdesc = rdesc; nor->addr_width = addr_width; nor->read_dummy = read_dummy;
Signature · 6 lines
2.20.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [RFC PATCH 2/3] mtd: spi-nor: sfdp: fix spi_nor_read_sfdp()
Quoted 21 lines · Michael Walle
If
spi_nor_read_sfdp()is used after probe, we have to setread_protoand the read dirmap.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 8 ++++++++ 1 file changed, 8 insertions(+)drivers/mtd/spi-nor/sfdp.c +2
-0@@ -179,19 +179,27 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, size_t len, void *buf) { u8 addr_width, read_opcode, read_dummy; +struct spi_mem_dirmap_desc *rdesc; +enum spi_nor_protocol read_proto;int ret; read_opcode = nor->read_opcode;
drivers/mtd/spi-nor/sfdp.c static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, · line 196
Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c +4
-0+ read_proto = nor->read_proto; + rdesc = nor->dirmap.rdesc; addr_width = nor->addr_width; read_dummy = nor->read_dummy; nor->read_opcode =SPINOR_OP_RDSFDP ; + nor->read_proto =SNOR_PROTO_1_1_1 ; + nor->dirmap.rdesc =NULL ; nor->addr_width =3 ; nor->read_dummy =8 ;
NACK. You can't assume the device is still in 1S-1S-1S mode after probe. For example, the s28hs512t flash is switched to 8D-8D-8D mode by the time the probe finishes so this would be an invalid command. Same for any flash that goes into a stateful mode.
And you can't even keep using nor->read_proto to read SFDP because the Read SFDP command might not be supported in all modes. xSPI spec (JESD251) says that the Read SFDP command is optional in 8D-8D-8D mode.
I think the best approach for this would be to cache the entire SFDP table at parse time. This obviously comes with a memory overhead but I don't think it would be too big. For example, the sfdp table on s28hs512t is 491 bytes and it has 6 tables. Anyway, if the memory usage is too much of a problem we can put the feature behind a config.
Quoted 12 lines
drivers/mtd/spi-nor/sfdp.c +2
-0ret =spi_nor_read_raw (nor, addr, len, buf); nor->read_opcode = read_opcode; + nor->read_proto = read_proto; + nor->dirmap.rdesc = rdesc; nor->addr_width = addr_width; nor->read_dummy = read_dummy;Signature · 1 line
2.20.1
Signature · 3 lines
Regards, Pratyush Yadav Texas Instruments Inc.
Re: [RFC PATCH 2/3] mtd: spi-nor: sfdp: fix spi_nor_read_sfdp()
Am 2021-03-16 12:04, schrieb Pratyush Yadav:
Quoted 28 lines · Michael Walle
Quoted 27 lines
If
spi_nor_read_sfdp()is used after probe, we have to setread_protoand the read dirmap.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 8 ++++++++ 1 file changed, 8 insertions(+)drivers/mtd/spi-nor/sfdp.c +4
-0@@ -179,19 +179,27 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, size_t len, void *buf) {u8 addr_width, read_opcode, read_dummy; +struct spi_mem_dirmap_desc *rdesc; +enum spi_nor_protocol read_proto;int ret; read_opcode = nor->read_opcode; + read_proto = nor->read_proto; + rdesc = nor->dirmap.rdesc; addr_width = nor->addr_width; read_dummy = nor->read_dummy;
Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, · line 196
Quoted 5 lines
drivers/mtd/spi-nor/sfdp.c +2
-0nor->read_opcode =SPINOR_OP_RDSFDP ; + nor->read_proto =SNOR_PROTO_1_1_1 ; + nor->dirmap.rdesc =NULL ; nor->addr_width =3 ; nor->read_dummy =8 ;NACK. You can't assume the device is still in 1S-1S-1S mode after probe. For example, the s28hs512t flash is switched to 8D-8D-8D mode by the time the probe finishes so this would be an invalid command. Same for any flash that goes into a stateful mode.
I see.
Quoted 9 lines
And you can't even keep using
nor->read_prototo read SFDP because the Read SFDP command might not be supported in all modes. xSPI spec (JESD251) says that the Read SFDP command is optional in 8D-8D-8D mode.I think the best approach for this would be to cache the entire SFDP table at parse time. This obviously comes with a memory overhead but I don't think it would be too big. For example, the sfdp table on s28hs512t is 491 bytes and it has 6 tables. Anyway, if the memory usage is too much of a problem we can put the feature behind a config.
I don't like to have it a config option, because then, if you really need it, i.e. some user has an unknown flash, it might not be there.
The next question would be, should I leave the current parsing code as is or should I also change that to use the sftp data cache. I'd prefer to leave it as is.
-michael
Re: [RFC PATCH 2/3] mtd: spi-nor: sfdp: fix spi_nor_read_sfdp()
Quoted 46 lines · Michael Walle
Am 2021-03-16 12:04, schrieb Pratyush Yadav:
Quoted 28 lines · Michael Walle
Quoted 27 lines
If
spi_nor_read_sfdp()is used after probe, we have to setread_protoand the read dirmap.Signed-off-by Michael Walle <[email protected]>--- drivers/mtd/spi-nor/sfdp.c | 8 ++++++++ 1 file changed, 8 insertions(+)drivers/mtd/spi-nor/sfdp.c +4
-0@@ -179,19 +179,27 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, size_t len, void *buf) {u8 addr_width, read_opcode, read_dummy; +struct spi_mem_dirmap_desc *rdesc; +enum spi_nor_protocol read_proto;int ret; read_opcode = nor->read_opcode; + read_proto = nor->read_proto; + rdesc = nor->dirmap.rdesc; addr_width = nor->addr_width; read_dummy = nor->read_dummy;Quoted 10 lines
drivers/mtd/spi-nor/sfdp.c static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr, · line 196
Quoted 5 lines
drivers/mtd/spi-nor/sfdp.c +2
-0nor->read_opcode =SPINOR_OP_RDSFDP ; + nor->read_proto =SNOR_PROTO_1_1_1 ; + nor->dirmap.rdesc =NULL ; nor->addr_width =3 ; nor->read_dummy =8 ;NACK. You can't assume the device is still in 1S-1S-1S mode after probe. For example, the s28hs512t flash is switched to 8D-8D-8D mode by the time the probe finishes so this would be an invalid command. Same for any flash that goes into a stateful mode.
I see.
Quoted 4 lines
And you can't even keep using
nor->read_prototo read SFDP because the Read SFDP command might not be supported in all modes. xSPI spec (JESD251) says that the Read SFDP command is optional in 8D-8D-8D mode.
Quoted 8 lines
Quoted 5 lines
I think the best approach for this would be to cache the entire SFDP table at parse time. This obviously comes with a memory overhead but I don't think it would be too big. For example, the sfdp table on s28hs512t is 491 bytes and it has 6 tables. Anyway, if the memory usage is too much of a problem we can put the feature behind a config.
I don't like to have it a config option, because then, if you really need it, i.e. some user has an unknown flash, it might not be there.
Right. Then let's hope people don't mind us using up an extra half kilobyte or so.
Quoted 4 lines
The next question would be, should I leave the current parsing code as is or should I also change that to use the sftp data cache. I'd prefer to leave it as is.
For this series its fine if you leave it as is. But eventually it would be a good idea to convert all SFDP parsers to use the cache to reduce the number of SFDP reads and potentially speed up flash initialization a bit.
Signature · 3 lines
Regards, Pratyush Yadav Texas Instruments Inc.
RFC PATCH 3/3 mtd: spi-nor: add sysfs and SFDP support
In reply to Michael WalleAdd support to dump the SFDP table. Not all flashes list their SFDP table contents in their datasheet. So having that is useful. It might also be helpful in bug reports from users.
The idea behind the sysfs module is also to have raw access to the SPI NOR flash device registers, which can also be useful for debugging.
--- drivers/mtd/spi-nor/Makefile | 2 +- drivers/mtd/spi-nor/core.c | 5 +++ drivers/mtd/spi-nor/core.h | 3 ++ drivers/mtd/spi-nor/sfdp.c | 4 +- drivers/mtd/spi-nor/sfdp.h | 2 + drivers/mtd/spi-nor/sysfs.c | 73 ++++++++++++++++++++++++++++++++++++ 6 files changed, 86 insertions(+), 3 deletions(-) create mode 100644 drivers/mtd/spi-nor/sysfs.c
drivers/mtd/spi-nor/Makefile +1 -1
@@ -1,6 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 -spi-nor-objs := core.o sfdp.o +spi-nor-objs := core.o sfdp.o sysfs.o spi-nor-objs += atmel.o spi-nor-objs += catalyst.o spi-nor-objs += eon.o
drivers/mtd/spi-nor/core.c +5 -0
@@ -3707,6 +3707,10 @@ static int spi_nor_probe(struct spi_mem *spimem)if (ret)return ret; + ret =spi_nor_sysfs_create (nor); +if (ret) +return ret; +return mtd_device_register (&nor->mtd, data ? data->parts :NULL , data ? data->nr_parts :0 ); }
@@ -3716,6 +3720,7 @@ static int spi_nor_remove(struct spi_mem *spimem)struct spi_nor *nor =spi_mem_get_drvdata (spimem);spi_nor_restore (nor); +spi_nor_sysfs_remove (nor);/* Clean up MTD stuff. */ return mtd_device_unregister (&nor->mtd);
drivers/mtd/spi-nor/core.h +3 -0
@@ -478,4 +478,7 @@ static struct spi_nor __maybe_unused *mtd_to_spi_nor(struct mtd_info *mtd) return mtd->priv; } +int spi_nor_sysfs_create (struct spi_nor *nor); +void spi_nor_sysfs_remove (struct spi_nor *nor); +#endif /* __LINUX_MTD_SPI_NOR_INTERNAL_H */
drivers/mtd/spi-nor/sfdp.c +2 -2
@@ -219,8 +219,8 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,* Return: -ENOMEM if kmalloc() fails, the return code of spi_nor_read_sfdp() * otherwise. */ -static int spi_nor_read_sfdp_dma_unsafe (struct spi_nor *nor,u32 addr, -size_t len,void *buf) +int spi_nor_read_sfdp_dma_unsafe (struct spi_nor *nor,u32 addr, +size_t len,void *buf) {void *dma_safe_buf;int ret;
drivers/mtd/spi-nor/sfdp.h +2 -0
@@ -109,5 +109,7 @@ struct sfdp_parameter_header {int spi_nor_parse_sfdp (struct spi_nor *nor,struct spi_nor_flash_parameter *params); +int spi_nor_read_sfdp_dma_unsafe (struct spi_nor *nor,u32 addr, +size_t len,void *buf);#endif /* __LINUX_MTD_SFDP_H */
drivers/mtd/spi-nor/sysfs.c new file +73 -0
73 lines not on this page · raw message
Signature · 1 line
2.20.1