iio: inv_mpu6050: Fully validate gyro and accel scale writes
Subsystems (2)
PATCH 1/1 iio: inv_mpu6050: Fully validate gyro and accel scale writes
When setting the gyro or accelerometer scale the inv_mpu6050 driver ignores the integer part of the value. As a result e.g. all of 0.13309, 1.13309, 12345.13309, ... are accepted as a valid gyro scale and 0.13309 is the scale that gets set in all those cases.
Make sure to check that the integer part of the scale value is 0 and reject it otherwise.
--- drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-)
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +14 -6
@@ -731,12 +731,16 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev, } } -static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val, +int val2) {int result, i; +if (val !=0 ) +return -EINVAL ; +for (i =0 ; i <ARRAY_SIZE (gyro_scale_6050); ++i) { -if (gyro_scale_6050[i] == val) { +if (gyro_scale_6050[i] == val2) { result =inv_mpu6050_set_gyro_fsr (st, i);if (result)return result;
@@ -767,13 +771,17 @@ static int inv_write_raw_get_fmt(struct iio_dev *indio_dev,return -EINVAL ; } -static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val, +int val2) {int result, i;u8 d; +if (val !=0 ) +return -EINVAL ; +for (i =0 ; i <ARRAY_SIZE (accel_scale); ++i) { -if (accel_scale[i] == val) { +if (accel_scale[i] == val2) { d = (i <<INV_MPU6050_ACCL_CONFIG_FSR_SHIFT ); result =regmap_write (st->map, st->reg->accl_config, d);if (result)
@@ -814,10 +822,10 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,case IIO_CHAN_INFO_SCALE :switch (chan->type) {case IIO_ANGL_VEL : - result =inv_mpu6050_write_gyro_scale (st, val2); + result =inv_mpu6050_write_gyro_scale (st, val, val2);break ;case IIO_ACCEL : - result =inv_mpu6050_write_accel_scale (st, val2); + result =inv_mpu6050_write_accel_scale (st, val, val2);break ;default : result = -EINVAL ;
Signature · 1 line
2.20.1
Jonathan Cameron
maintainerQuoted 10 lines · On Mon, 5 Apr 2021 13:44:41 +0200 Lars-Peter Clausen <[email protected]> wrote:
When setting the gyro or accelerometer scale the
inv_mpu6050driver ignores the integer part of the value. As a result e.g. all of 0.13309, 1.13309, 12345.13309, ... are accepted as a valid gyro scale and 0.13309 is the scale that gets set in all those cases.Make sure to check that the integer part of the scale value is 0 and reject it otherwise.
Fixes 09a642b78523 ("Invensense MPU6050 Device Driver.")Signed-off-by Lars-Peter Clausen <[email protected]>
Looks like this is in the 'obviously' correct category to me but will leave it on list to give Jean-Baptiste a chance to look at it.
As ever, give me a poke if I seem to have lost it down the back of the sofa in a few weeks time.
Thanks
Jonathan
Quoted 60 lines
--- drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-)drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +14
-6@@ -731,12 +731,16 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev, } } -static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val, +int val2) {int result, i; +if (val !=0 ) +return -EINVAL ; +for (i =0 ; i <ARRAY_SIZE (gyro_scale_6050); ++i) { -if (gyro_scale_6050[i] == val) { +if (gyro_scale_6050[i] == val2) { result =inv_mpu6050_set_gyro_fsr (st, i);if (result)return result;@@ -767,13 +771,17 @@ static int inv_write_raw_get_fmt(struct iio_dev *indio_dev,return -EINVAL ; } -static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val, +int val2) {int result, i;u8 d; +if (val !=0 ) +return -EINVAL ; +for (i =0 ; i <ARRAY_SIZE (accel_scale); ++i) { -if (accel_scale[i] == val) { +if (accel_scale[i] == val2) { d = (i <<INV_MPU6050_ACCL_CONFIG_FSR_SHIFT ); result =regmap_write (st->map, st->reg->accl_config, d);if (result)@@ -814,10 +822,10 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,case IIO_CHAN_INFO_SCALE :switch (chan->type) {case IIO_ANGL_VEL : - result =inv_mpu6050_write_gyro_scale (st, val2); + result =inv_mpu6050_write_gyro_scale (st, val, val2);break ;case IIO_ACCEL : - result =inv_mpu6050_write_accel_scale (st, val2); + result =inv_mpu6050_write_accel_scale (st, val, val2);break ;default : result = -EINVAL ;
Jean-Baptiste Maneyrol
Acked-byHi Jonathan, Lars-Peter,
thanks for letting me having a look. This is effectively as obvious as it looks. Never think of testing that, thanks for the patch.
Thanks,
JB
From: Jonathan Cameron <[email protected]>
Sent: Monday, April 5, 2021 16:55
To: Lars-Peter Clausen <[email protected]>
Cc: Jean-Baptiste Maneyrol <[email protected]>; [email protected] <[email protected]>
Subject: Re: [PATCH] iio: inv_mpu6050: Fully validate gyro and accel scale writes
CAUTION: This email originated from outside of the organization. Please make sure the sender is who they say they are and do not click links or open attachments unless you recognize the sender and know the content is safe.
Quoted 10 lines · On Mon, 5 Apr 2021 13:44:41 +0200 Lars-Peter Clausen <[email protected]> wrote:
When setting the gyro or accelerometer scale the
inv_mpu6050driver ignores the integer part of the value. As a result e.g. all of 0.13309, 1.13309, 12345.13309, ... are accepted as a valid gyro scale and 0.13309 is the scale that gets set in all those cases.Make sure to check that the integer part of the scale value is 0 and reject it otherwise.
Fixes 09a642b78523 ("Invensense MPU6050 Device Driver.")Signed-off-by Lars-Peter Clausen <[email protected]>
Looks like this is in the 'obviously' correct category to me but will leave it on list to give Jean-Baptiste a chance to look at it.
As ever, give me a poke if I seem to have lost it down the back of the sofa in a few weeks time.
Thanks
Jonathan
Quoted 60 lines
---
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c| 20 ++++++++++++++------1 file changed, 14 insertions(+), 6 deletions(-)drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +0
-0@@ -731,12 +731,16 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev, } }drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +2
-1-static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val, + int val2){
int result, i;
+ if (val != 0)
+ return-EINVAL;
+
for (i = 0; i <ARRAY_SIZE(gyro_scale_6050); ++i) { - if (gyro_scale_6050[i] == val) {
+ if (gyro_scale_6050[i] == val2) {
result =inv_mpu6050_set_gyro_fsr(st, i); if (result)
return result;drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +0
-0@@ -767,13 +771,17 @@ static int inv_write_raw_get_fmt(struct iio_dev *indio_dev, return -EINVAL; }drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +2
-1-static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val, + int val2){
int result, i;
u8 d;
+ if (val != 0)
+ return-EINVAL;
+
for (i = 0; i <ARRAY_SIZE(accel_scale); ++i) {
- if (accel_scale[i] == val) {
+ if (accel_scale[i] == val2) {
d = (i <<INV_MPU6050_ACCL_CONFIG_FSR_SHIFT); result =regmap_write(st->map, st->reg->accl_config, d); if (result)drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +0
-0@@ -814,10 +822,10 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,case
IIO_CHAN_INFO_SCALE:
switch (chan->type) {
caseIIO_ANGL_VEL:
- result =inv_mpu6050_write_gyro_scale(st, val2); + result =inv_mpu6050_write_gyro_scale(st, val, val2); break;
caseIIO_ACCEL:
- result =inv_mpu6050_write_accel_scale(st, val2); + result =inv_mpu6050_write_accel_scale(st, val, val2); break;
default:
result =-EINVAL;
Quoted 6 lines · On Tue, 6 Apr 2021 07:51:05 +0000 Jean-Baptiste Maneyrol…
Hi Jonathan, Lars-Peter,
thanks for letting me having a look. This is effectively as obvious as it looks. Never think of testing that, thanks for the patch.
Applied to the togreg branch of iio.git and marked for stable.
Thanks,
Jonathan
Quoted 95 lines
Thanks,
JBFrom: Jonathan Cameron <[email protected]>
Sent: Monday, April 5, 2021 16:55
To: Lars-Peter Clausen <[email protected]>
Cc: Jean-Baptiste Maneyrol <[email protected]>; [email protected] <[email protected]>
Subject: Re: [PATCH] iio:inv_mpu6050: Fully validate gyro and accel scale writes
CAUTION: This email originated from outside of the organization. Please make sure the sender is who they say they are and do not click links or open attachments unless you recognize the sender and know the content is safe.Quoted 10 lines · On Mon, 5 Apr 2021 13:44:41 +0200 Lars-Peter Clausen <[email protected]> wrote:
When setting the gyro or accelerometer scale the
inv_mpu6050driver ignores the integer part of the value. As a result e.g. all of 0.13309, 1.13309, 12345.13309, ... are accepted as a valid gyro scale and 0.13309 is the scale that gets set in all those cases.Make sure to check that the integer part of the scale value is 0 and reject it otherwise.
Fixes 09a642b78523 ("Invensense MPU6050 Device Driver.")Signed-off-by Lars-Peter Clausen <[email protected]>Looks like this is in the 'obviously' correct category to me but will leave it on list to give Jean-Baptiste a chance to look at it.
As ever, give me a poke if I seem to have lost it down the back of the sofa in a few weeks time.
Thanks
Jonathan
Quoted 60 lines
---
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c| 20 ++++++++++++++------1 file changed, 14 insertions(+), 6 deletions(-)drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +0
-0@@ -731,12 +731,16 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev, } }drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +2
-1-static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_gyro_scale (struct inv_mpu6050_state *st,int val, + int val2){
int result, i;
+ if (val != 0)
+ return-EINVAL;
+
for (i = 0; i <ARRAY_SIZE(gyro_scale_6050); ++i) { - if (gyro_scale_6050[i] == val) {
+ if (gyro_scale_6050[i] == val2) {
result =inv_mpu6050_set_gyro_fsr(st, i); if (result)
return result;drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +0
-0@@ -767,13 +771,17 @@ static int inv_write_raw_get_fmt(struct iio_dev *indio_dev, return -EINVAL; }drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +2
-1-static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val) +static int inv_mpu6050_write_accel_scale (struct inv_mpu6050_state *st,int val, + int val2){
int result, i;
u8 d;
+ if (val != 0)
+ return-EINVAL;
+
for (i = 0; i <ARRAY_SIZE(accel_scale); ++i) {
- if (accel_scale[i] == val) {
+ if (accel_scale[i] == val2) {
d = (i <<INV_MPU6050_ACCL_CONFIG_FSR_SHIFT); result =regmap_write(st->map, st->reg->accl_config, d); if (result)drivers/iio/imu/inv_mpu6050/inv_mpu_core.c +0
-0@@ -814,10 +822,10 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,case
IIO_CHAN_INFO_SCALE:
switch (chan->type) {
caseIIO_ANGL_VEL:
- result =inv_mpu6050_write_gyro_scale(st, val2); + result =inv_mpu6050_write_gyro_scale(st, val, val2); break;
caseIIO_ACCEL:
- result =inv_mpu6050_write_accel_scale(st, val2); + result =inv_mpu6050_write_accel_scale(st, val, val2); break;
default:
result =-EINVAL;