Bluetooth: hci_h5: Disable the hci_suspend_notifier for btrtl devices
PATCH RESEND 1/1 Bluetooth: hci_h5: Disable the hci_suspend_notifier for btrtl devices
The hci_suspend_notifier which was introduced last year, is causing problems for uart attached btrtl devices. These devices may loose their firmware and their baudrate setting over a suspend/resume.
Since we don't even know the baudrate after a suspend/resume recovering from this is tricky. The driver solves this by treating these devices the same as USB BT HCIs which drop of the bus during suspend.
Specifically the driver:
1. Simply unconditionally turns the device fully off during system-suspend to save maximum power.
2. Calls device_reprobe() from a workqueue to fully re-init the device from scratch on system-resume (unregistering the old HCI and registering a new HCI).
This means that these devices do not benefit from the suspend / resume handling work done by the hci_suspend_notifier. At best this unnecessarily adds some time to the suspend/resume time.
But in practice this is actually causing problems:
1. These btrtl devices seem to not like the HCI_OP_WRITE_SCAN_ENABLE( SCAN_DISABLED) request being send to them when entering the BT_SUSPEND_CONFIGURE_WAKE state. The same request send on BT_SUSPEND_DISCONNECT works fine, but the second one send (unnecessarily?) from the BT_SUSPEND_CONFIGURE_WAKE transition causes the device to hang:
[ 573.497754] PM: suspend entry (s2idle) [ 573.554615] Filesystems sync: 0.056 seconds [ 575.837753] Bluetooth: hci0: Timed out waiting for suspend events [ 575.837801] Bluetooth: hci0: Suspend timeout bit: 4 [ 575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -110
2. The PM_POST_SUSPEND / BT_RUNNING transition races with the driver-unbinding done by the device_reprobe() work.
If the hci_suspend_notifier wins the race it is talking to a dead device leading to the following errors being logged:
[ 598.686060] Bluetooth: hci0: Timed out waiting for suspend events [ 598.686124] Bluetooth: hci0: Suspend timeout bit: 5 [ 598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110
In both cases things still work, but the suspend-notifier is causing these ugly errors getting logged and ut increase both the suspend- and the resume-time by 2 seconds.
This commit avoids these problems by disabling the hci_suspend_notifier.
---
Changes in v2:
- Use the new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk, instead of directly unregistering the notifier from hci_h5.c
--- drivers/bluetooth/hci_h5.c | 7 +++++++ drivers/bluetooth/hci_serdev.c | 3 +++ drivers/bluetooth/hci_uart.h | 13 +++++++------ 3 files changed, 17 insertions(+), 6 deletions(-)
drivers/bluetooth/hci_h5.c +7 -0
@@ -919,6 +919,13 @@ static int h5_btrtl_setup(struct h5 *h5)static void h5_btrtl_open (struct h5 *h5) { +/* +* Since h5_btrtl_resume() does a device_reprobe() the suspend handling +* done by the hci_suspend_notifier is not necessary; it actually causes +* delays and a bunch of errors to get logged, so disable it. +*/ +set_bit (HCI_UART_NO_SUSPEND_NOTIFIER , &h5->hu->hdev_flags); +/* Devices always start with these fixed parameters */ serdev_device_set_flow_control (h5->hu->serdev, false);serdev_device_set_parity (h5->hu->serdev,SERDEV_PARITY_EVEN );
drivers/bluetooth/hci_serdev.c +3 -0
@@ -349,6 +349,9 @@ int hci_uart_register_device(struct hci_uart *hu,if (test_bit (HCI_UART_EXT_CONFIG , &hu->hdev_flags))set_bit (HCI_QUIRK_EXTERNAL_CONFIG , &hdev->quirks); +if (test_bit (HCI_UART_NO_SUSPEND_NOTIFIER , &hu->hdev_flags)) +set_bit (HCI_QUIRK_NO_SUSPEND_NOTIFIER , &hdev->quirks); +if (test_bit (HCI_UART_CREATE_AMP , &hu->hdev_flags)) hdev->dev_type =HCI_AMP ;else
drivers/bluetooth/hci_uart.h +7 -6
@@ -35,12 +35,13 @@#define HCI_UART_NOKIA 10#define HCI_UART_MRVL 11 -#define HCI_UART_RAW_DEVICE 0 -#define HCI_UART_RESET_ON_INIT 1 -#define HCI_UART_CREATE_AMP 2 -#define HCI_UART_INIT_PENDING 3 -#define HCI_UART_EXT_CONFIG 4 -#define HCI_UART_VND_DETECT 5 +#define HCI_UART_RAW_DEVICE 0 +#define HCI_UART_RESET_ON_INIT 1 +#define HCI_UART_CREATE_AMP 2 +#define HCI_UART_INIT_PENDING 3 +#define HCI_UART_EXT_CONFIG 4 +#define HCI_UART_VND_DETECT 5 +#define HCI_UART_NO_SUSPEND_NOTIFIER 6struct hci_uart ;struct serdev_device ;
Signature · 1 line
2.30.2
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list. This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=461011
---Test result---
##############################
Test: CheckPatch - PASS
##############################
Test: CheckGitLint - PASS
##############################
Test: CheckBuildK - PASS
##############################
Test: CheckTestRunner: Setup - PASS
##############################
Test: CheckTestRunner: l2cap-tester - PASS
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6
##############################
Test: CheckTestRunner: bnep-tester - PASS
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: mgmt-tester - PASS
Total: 416, Passed: 402 (96.6%), Failed: 0, Not Run: 14
##############################
Test: CheckTestRunner: rfcomm-tester - PASS
Total: 9, Passed: 9 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: sco-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: smp-tester - PASS
Total: 8, Passed: 8 (100.0%), Failed: 0, Not Run: 0
##############################
Test: CheckTestRunner: userchan-tester - PASS
Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0
---
Regards,
Linux Bluetooth
c[?7l[2JSeaBIOS (version 1.13.0-1ubuntu1.1) Booting from ROM..c[?7l[2Jearly console in extract_kernelinput_data: 0x0000000001e732e0input_len: 0x00000000003532f3
output: 0x0000000001000000output_len: 0x00000000011944cckernel_total_size: 0x0000000001030000needed_size: 0x0000000001200000trampoline_32bit: 0x000000000009d000
Physical KASLR using RDTSC...
Virtual KASLR using RDTSC...
Decompressing Linux... Parsing ELF... Performing relocations... done.
Booting the kernel.
Linux version 5.11.0-g4174e7ab9aee (root@b391cbe99e1a) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #2 Mon Apr 5 21:09:20 UTC 2021
Command line: console=ttyS0,115200n8 earlyprintk=serial rootfstype=9p rootflags=trans=virtio,version=9p2000.L acpi=off pci=noacpi noapic quiet ro init=/github/workspace/bluez/tools/test-runner TESTHOME=/github/workspace TESTDBUS=0 TESTMONITOR=0 TESTDEVS=0 TESTAUTO=0 TESTARGS='/github/workspace/bluez/tools/l2cap-tester' x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000000bffdfff] usable
BIOS-e820: [mem 0x000000000bffe000-0x000000000bffffff] reserved
BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
printk: bootconsole [earlyser0] enabled
Memory KASLR using RDTSC...
Poking KASLR using RDTSC...
Mounting sysfs to /sys
Mounting proc to /proc
Mounting devtmpfs to /dev
Creating /dev/pts
Mounting devpts to /dev/pts
Creating /dev/shm
Mounting tmpfs to /dev/shm
Mounting tmpfs to /run
Mounting tmpfs to /tmp
Mounting debugfs to /sys/kernel/debug
Linking /dev/fd to /proc/self/fd
Linking /dev/stdin to /proc/self/fd/0
Linking /dev/stdout to /proc/self/fd/1
Linking /dev/stderr to /proc/self/fd/2
Creating new session group leader
Setting controlling terminal
Creating /var/lib/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/dbus-1
Failed to create filesystem: No such file or directory
Creating /usr/share/dbus-1
Running command /github/workspace/bluez/tools/l2cap-tester
New process 38 created
Changing into directory /github/workspace
Basic L2CAP Socket - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Basic L2CAP Socket - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Basic L2CAP Socket - Success - setup complete
Basic L2CAP Socket - Success - run
Basic L2CAP Socket - Success - test passed
Basic L2CAP Socket - Success - teardown
Index Removed callback
Index: 0x0000
Basic L2CAP Socket - Success - teardown complete
Basic L2CAP Socket - Success - done
Non-connected getpeername - Failure - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Non-connected getpeername - Failure - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Non-connected getpeername - Failure - setup complete Non-connected getpeername - Failure - run Non-connected getpeername - Failure - test passed Non-connected getpeername - Failure - teardown
Index Removed callback
Index: 0x0000
Non-connected getpeername - Failure - teardown complete Non-connected getpeername - Failure - done
L2CAP BR/EDR Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Success - setup complete
L2CAP BR/EDR Client - Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Success - test passed
L2CAP BR/EDR Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Success - teardown complete
L2CAP BR/EDR Client - Success - done
L2CAP BR/EDR Client SSP - Success 1 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client SSP - Success 1 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Client enable SSP status 0x00
L2CAP BR/EDR Client SSP - Success 1 - setup complete L2CAP BR/EDR Client SSP - Success 1 - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client SSP - Success 1 - test passed L2CAP BR/EDR Client SSP - Success 1 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client SSP - Success 1 - teardown complete L2CAP BR/EDR Client SSP - Success 1 - done
L2CAP BR/EDR Client SSP - Success 2 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client SSP - Success 2 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Client enable SSP status 0x00
L2CAP BR/EDR Client SSP - Success 2 - setup complete L2CAP BR/EDR Client SSP - Success 2 - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client SSP - Success 2 - test passed L2CAP BR/EDR Client SSP - Success 2 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client SSP - Success 2 - teardown complete L2CAP BR/EDR Client SSP - Success 2 - done
L2CAP BR/EDR Client PIN Code - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client PIN Code - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client PIN Code - Success - setup complete L2CAP BR/EDR Client PIN Code - Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client PIN Code - Success - test passed L2CAP BR/EDR Client PIN Code - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client PIN Code - Success - teardown complete L2CAP BR/EDR Client PIN Code - Success - done
L2CAP BR/EDR Client - Read Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Read Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Read Success - setup complete L2CAP BR/EDR Client - Read Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Read Success - test passed L2CAP BR/EDR Client - Read Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Read Success - teardown complete L2CAP BR/EDR Client - Read Success - done
L2CAP BR/EDR Client - Write Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Write Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Write Success - setup complete L2CAP BR/EDR Client - Write Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Write Success - test passed L2CAP BR/EDR Client - Write Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Write Success - teardown complete L2CAP BR/EDR Client - Write Success - done
L2CAP BR/EDR Client - Invalid PSM 1 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Invalid PSM 1 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Invalid PSM 1 - setup complete L2CAP BR/EDR Client - Invalid PSM 1 - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP BR/EDR Client - Invalid PSM 1 - test passed L2CAP BR/EDR Client - Invalid PSM 1 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Invalid PSM 1 - teardown complete L2CAP BR/EDR Client - Invalid PSM 1 - done
L2CAP BR/EDR Client - Invalid PSM 2 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Invalid PSM 2 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Invalid PSM 2 - setup complete L2CAP BR/EDR Client - Invalid PSM 2 - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP BR/EDR Client - Invalid PSM 2 - test passed L2CAP BR/EDR Client - Invalid PSM 2 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Invalid PSM 2 - teardown complete L2CAP BR/EDR Client - Invalid PSM 2 - done
L2CAP BR/EDR Client - Invalid PSM 3 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Invalid PSM 3 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Client enable SSP status 0x00
L2CAP BR/EDR Client - Invalid PSM 3 - setup complete L2CAP BR/EDR Client - Invalid PSM 3 - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP BR/EDR Client - Invalid PSM 3 - test passed L2CAP BR/EDR Client - Invalid PSM 3 - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Invalid PSM 3 - teardown complete L2CAP BR/EDR Client - Invalid PSM 3 - done
L2CAP BR/EDR Client - Socket Shut WR Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Client - Socket Shut WR Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP BR/EDR Client - Socket Shut WR Success - setup complete L2CAP BR/EDR Client - Socket Shut WR Success - run
Connect in progress
Successfully connected
L2CAP BR/EDR Client - Socket Shut WR Success - test passed L2CAP BR/EDR Client - Socket Shut WR Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Client - Socket Shut WR Success - teardown complete L2CAP BR/EDR Client - Socket Shut WR Success - done
L2CAP BR/EDR Server - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Success - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Success - setup complete
L2CAP BR/EDR Server - Success - run
Listening for connections
New client connection with handle 0x002a
Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Success - test passed
Successfully connected
L2CAP BR/EDR Server - Success - test passed
L2CAP BR/EDR Server - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Success - teardown complete
L2CAP BR/EDR Server - Success - done
L2CAP BR/EDR Server - Read Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Read Success - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Read Success - setup complete L2CAP BR/EDR Server - Read Success - run
Listening for connections
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Read Success - test passed L2CAP BR/EDR Server - Read Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Read Success - teardown complete L2CAP BR/EDR Server - Read Success - done
L2CAP BR/EDR Server - Write Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Write Success - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Write Success - setup complete L2CAP BR/EDR Server - Write Success - run
Listening for connections
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Write Success - test passed L2CAP BR/EDR Server - Write Success - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Write Success - teardown complete L2CAP BR/EDR Server - Write Success - done
L2CAP BR/EDR Server - Security Block - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Security Block - setup
Powering on controller
Controller powered on
Server enable SSP status 0x00
L2CAP BR/EDR Server - Security Block - setup complete L2CAP BR/EDR Server - Security Block - run
Listening for connections
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Security Block - test passed L2CAP BR/EDR Server - Security Block - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Security Block - teardown complete L2CAP BR/EDR Server - Security Block - done
L2CAP BR/EDR Server - Invalid PSM - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid PSM - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid PSM - setup complete L2CAP BR/EDR Server - Invalid PSM - run
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x03
L2CAP BR/EDR Server - Invalid PSM - test passed L2CAP BR/EDR Server - Invalid PSM - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid PSM - teardown complete L2CAP BR/EDR Server - Invalid PSM - done
L2CAP BR/EDR Server - Invalid PDU - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid PDU - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid PDU - setup complete L2CAP BR/EDR Server - Invalid PDU - run
New client connection with handle 0x002a Sending L2CAP Request from client
Bluetooth: Wrong link type (-71)
Client received response code 0x01
L2CAP BR/EDR Server - Invalid PDU - test passed L2CAP BR/EDR Server - Invalid PDU - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid PDU - teardown complete L2CAP BR/EDR Server - Invalid PDU - done
L2CAP BR/EDR Server - Invalid Disconnect CID - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid Disconnect CID - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid Disconnect CID - setup complete L2CAP BR/EDR Server - Invalid Disconnect CID - run
New client connection with handle 0x002a
Sending L2CAP Request from client
Client received response code 0x01
L2CAP BR/EDR Server - Invalid Disconnect CID - test passed L2CAP BR/EDR Server - Invalid Disconnect CID - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid Disconnect CID - teardown complete L2CAP BR/EDR Server - Invalid Disconnect CID - done
L2CAP BR/EDR Server - Invalid Config CID - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP BR/EDR Server - Invalid Config CID - setup
Powering on controller
Controller powered on
L2CAP BR/EDR Server - Invalid Config CID - setup complete L2CAP BR/EDR Server - Invalid Config CID - run
New client connection with handle 0x002a Sending L2CAP Request from client
Client received response code 0x01
L2CAP BR/EDR Server - Invalid Config CID - test passed L2CAP BR/EDR Server - Invalid Config CID - teardown
Index Removed callback
Index: 0x0000
L2CAP BR/EDR Server - Invalid Config CID - teardown complete L2CAP BR/EDR Server - Invalid Config CID - done
L2CAP LE Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Success - setup complete
L2CAP LE Client - Success - run
Connect in progress
Successfully connected
L2CAP LE Client - Success - test passed
L2CAP LE Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Success - teardown complete
L2CAP LE Client - Success - done
L2CAP LE Client, Direct Advertising - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client, Direct Advertising - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client, Direct Advertising - Success - setup complete L2CAP LE Client, Direct Advertising - Success - run
Connect in progress
Received advertising parameters HCI command
L2CAP LE Client, Direct Advertising - Success - test passed L2CAP LE Client, Direct Advertising - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client, Direct Advertising - Success - teardown complete L2CAP LE Client, Direct Advertising - Success - done
L2CAP LE Client SMP - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client SMP - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client SMP - Success - setup complete
L2CAP LE Client SMP - Success - run
Connect in progress
Successfully connected
L2CAP LE Client SMP - Success - test passed
Bluetooth: hci0: link tx timeout
L2CAP LE Client SMP - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client SMP - Success - teardown complete
L2CAP LE Client SMP - Success - done
L2CAP LE Client - Command Reject - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Command Reject - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Command Reject - setup complete
L2CAP LE Client - Command Reject - run
Connect in progress
New connection with handle 0x002a
Connect failed: Connection refused (111)
L2CAP LE Client - Command Reject - test passed
L2CAP LE Client - Command Reject - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Command Reject - teardown complete L2CAP LE Client - Command Reject - done
L2CAP LE Client - Connection Reject - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: L2CAP LE Client - Connection Reject - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Connection Reject - setup complete L2CAP LE Client - Connection Reject - run
Can't connect socket: No route to host (113)
L2CAP LE Client - Connection Reject - test passed L2CAP LE Client - Connection Reject - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Connection Reject - teardown complete L2CAP LE Client - Connection Reject - done
L2CAP LE Client - Close socket 1 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Close socket 1 - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Close socket 1 - setup complete
L2CAP LE Client - Close socket 1 - run
Connect in progress, sk = 13
Will close socket during scan phase...
Checking whether scan was properly stopped...
L2CAP LE Client - Close socket 1 - test passed
L2CAP LE Client - Close socket 1 - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Close socket 1 - teardown complete L2CAP LE Client - Close socket 1 - done
L2CAP LE Client - Close socket 2 - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Close socket 2 - setup
Powering on controller
Controller powered on
L2CAP LE Client - Close socket 2 - setup complete
L2CAP LE Client - Close socket 2 - run
Connect in progress, sk = 13
Client set connectable status 0x00
Client set connectable status 0x00
L2CAP LE Client - Close socket 2 - test passed
L2CAP LE Client - Close socket 2 - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Close socket 2 - teardown complete L2CAP LE Client - Close socket 2 - done
L2CAP LE Client - Open two sockets - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Open two sockets - setup
Powering on controller
Controller powered on
L2CAP LE Client - Open two sockets - setup complete L2CAP LE Client - Open two sockets - run
Connect in progress, sk = 13
HCI Command 0x200b length 7
HCI Command 0x200c length 2
Connect in progress, sk = 14
HCI Command 0x200c length 2
Client set connectable status 0x00
HCI Command 0x200d length 25
HCI Command 0x2016 length 2
Successfully connected
Successfully connected
L2CAP LE Client - Open two sockets - test passed
(l2cap-tester:38): GLib-WARNING **: 21:09:28.132: Invalid file descriptor. L2CAP LE Client - Open two sockets - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Open two sockets - teardown complete L2CAP LE Client - Open two sockets - done
L2CAP LE Client - Open two sockets close one - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Open two sockets close one - setup
Powering on controller
Controller powered on
L2CAP LE Client - Open two sockets close one - setup complete L2CAP LE Client - Open two sockets close one - run
Connect in progress, sk = 13
HCI Command 0x200b length 7
HCI Command 0x200c length 2
Connect in progress, sk = 14
Closing first socket! 13
HCI Command 0x200c length 2
Client set connectable status 0x00
HCI Command 0x200d length 25
HCI Command 0x2016 length 2
Successfully connected
L2CAP LE Client - Open two sockets close one - test passed
(l2cap-tester:38): GLib-WARNING **: 21:09:28.179: Invalid file descriptor. L2CAP LE Client - Open two sockets close one - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Open two sockets close one - teardown complete L2CAP LE Client - Open two sockets close one - done
L2CAP LE Client - Invalid PSM - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Client - Invalid PSM - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE Client - Invalid PSM - setup complete
L2CAP LE Client - Invalid PSM - run
Connect in progress
Connect failed: Connection refused (111)
L2CAP LE Client - Invalid PSM - test passed
L2CAP LE Client - Invalid PSM - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Client - Invalid PSM - teardown complete
L2CAP LE Client - Invalid PSM - done
L2CAP LE Server - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Server - Success - setup
Powering on controller
Controller powered on
L2CAP LE Server - Success - setup complete
L2CAP LE Server - Success - run
Listening for connections
New client connection with handle 0x002a
Sending L2CAP Request from client
Successfully connected
L2CAP LE Server - Success - test passed
Client received response code 0x15
L2CAP LE Server - Success - test passed
L2CAP LE Server - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Server - Success - teardown complete
L2CAP LE Server - Success - done
L2CAP LE Server - Nval SCID - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE Server - Nval SCID - setup
Powering on controller
Controller powered on
L2CAP LE Server - Nval SCID - setup complete
L2CAP LE Server - Nval SCID - run
Listening for connections
New client connection with handle 0x002a
Sending L2CAP Request from client
Client received response code 0x15
L2CAP LE Server - Nval SCID - test passed
L2CAP LE Server - Nval SCID - teardown
Index Removed callback
Index: 0x0000
L2CAP LE Server - Nval SCID - teardown complete
L2CAP LE Server - Nval SCID - done
L2CAP Ext-Flowctl Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client - Success - setup complete L2CAP Ext-Flowctl Client - Success - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client - Success - test not run L2CAP Ext-Flowctl Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Success - teardown complete L2CAP Ext-Flowctl Client - Success - done
L2CAP Ext-Flowctl Client, Direct Advertising - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client, Direct Advertising - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client, Direct Advertising - Success - setup complete L2CAP Ext-Flowctl Client, Direct Advertising - Success - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client, Direct Advertising - Success - test not run L2CAP Ext-Flowctl Client, Direct Advertising - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client, Direct Advertising - Success - teardown complete L2CAP Ext-Flowctl Client, Direct Advertising - Success - done
L2CAP Ext-Flowctl Client SMP - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client SMP - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client SMP - Success - setup complete L2CAP Ext-Flowctl Client SMP - Success - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client SMP - Success - test not run L2CAP Ext-Flowctl Client SMP - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client SMP - Success - teardown complete L2CAP Ext-Flowctl Client SMP - Success - done
L2CAP Ext-Flowctl Client - Command Reject - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Command Reject - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP Ext-Flowctl Client - Command Reject - setup complete L2CAP Ext-Flowctl Client - Command Reject - run
Can't set mode: Protocol not available (92)
L2CAP Ext-Flowctl Client - Command Reject - test not run L2CAP Ext-Flowctl Client - Command Reject - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Command Reject - teardown complete L2CAP Ext-Flowctl Client - Command Reject - done
L2CAP Ext-Flowctl Client - Open two sockets - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Open two sockets - setup
Powering on controller
Controller powered on
L2CAP Ext-Flowctl Client - Open two sockets - setup complete L2CAP Ext-Flowctl Client - Open two sockets - run
Can't set mode: Protocol not available (92) Error in create_l2cap_sock
L2CAP Ext-Flowctl Client - Open two sockets - test not run L2CAP Ext-Flowctl Client - Open two sockets - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Open two sockets - teardown complete L2CAP Ext-Flowctl Client - Open two sockets - done
L2CAP Ext-Flowctl Client - Open two sockets close one - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP Ext-Flowctl Client - Open two sockets close one - setup
Powering on controller
Controller powered on
L2CAP Ext-Flowctl Client - Open two sockets close one - setup complete L2CAP Ext-Flowctl Client - Open two sockets close one - run
Can't set mode: Protocol not available (92)
Error in create_l2cap_sock
L2CAP Ext-Flowctl Client - Open two sockets close one - test not run L2CAP Ext-Flowctl Client - Open two sockets close one - teardown
Index Removed callback
Index: 0x0000
L2CAP Ext-Flowctl Client - Open two sockets close one - teardown complete L2CAP Ext-Flowctl Client - Open two sockets close one - done
L2CAP LE ATT Client - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE ATT Client - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
L2CAP LE ATT Client - Success - setup complete
L2CAP LE ATT Client - Success - run
Connect in progress
Successfully connected
L2CAP LE ATT Client - Success - test passed
L2CAP LE ATT Client - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE ATT Client - Success - teardown complete
L2CAP LE ATT Client - Success - done
L2CAP LE ATT Server - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: L2CAP LE ATT Server - Success - setup
Powering on controller
Controller powered on
L2CAP LE ATT Server - Success - setup complete
L2CAP LE ATT Server - Success - run
Listening for connections
New client connection with handle 0x002a
Successfully connected
L2CAP LE ATT Server - Success - test passed
L2CAP LE ATT Server - Success - teardown
Index Removed callback
Index: 0x0000
L2CAP LE ATT Server - Success - teardown complete
L2CAP LE ATT Server - Success - done
Test Summary
------------
Basic L2CAP Socket - Success Passed 0.064 seconds Non-connected getpeername - Failure Passed 0.018 seconds L2CAP BR/EDR Client - Success Passed 0.035 seconds L2CAP BR/EDR Client SSP - Success 1 Passed 0.034 seconds L2CAP BR/EDR Client SSP - Success 2 Passed 0.025 seconds L2CAP BR/EDR Client PIN Code - Success Passed 0.021 seconds L2CAP BR/EDR Client - Read Success Passed 0.024 seconds L2CAP BR/EDR Client - Write Success Passed 0.021 seconds L2CAP BR/EDR Client - Invalid PSM 1 Passed 0.025 seconds L2CAP BR/EDR Client - Invalid PSM 2 Passed 0.022 seconds L2CAP BR/EDR Client - Invalid PSM 3 Passed 0.024 seconds L2CAP BR/EDR Client - Socket Shut WR Success Passed 0.016 seconds L2CAP BR/EDR Server - Success Passed 0.025 seconds L2CAP BR/EDR Server - Read Success Passed 0.025 seconds L2CAP BR/EDR Server - Write Success Passed 0.023 seconds L2CAP BR/EDR Server - Security Block Passed 0.019 seconds L2CAP BR/EDR Server - Invalid PSM Passed 0.021 seconds L2CAP BR/EDR Server - Invalid PDU Passed 0.019 seconds L2CAP BR/EDR Server - Invalid Disconnect CID Passed 0.021 seconds L2CAP BR/EDR Server - Invalid Config CID Passed 0.022 seconds L2CAP LE Client - Success Passed 0.029 seconds L2CAP LE Client, Direct Advertising - Success Passed 0.018 seconds L2CAP LE Client SMP - Success Passed 0.032 seconds L2CAP LE Client - Command Reject Passed 0.018 seconds L2CAP LE Client - Connection Reject Passed 0.018 seconds L2CAP LE Client - Close socket 1 Passed 0.017 seconds L2CAP LE Client - Close socket 2 Passed 0.017 seconds L2CAP LE Client - Open two sockets Passed 0.059 seconds L2CAP LE Client - Open two sockets close one Passed 0.028 seconds L2CAP LE Client - Invalid PSM Passed 0.029 seconds L2CAP LE Server - Success Passed 0.029 seconds L2CAP LE Server - Nval SCID Passed 0.018 seconds L2CAP Ext-Flowctl Client - Success Not Run L2CAP Ext-Flowctl Client, Direct Advertising - Success Not Run L2CAP Ext-Flowctl Client SMP - Success Not Run L2CAP Ext-Flowctl Client - Command Reject Not Run L2CAP Ext-Flowctl Client - Open two sockets Not Run L2CAP Ext-Flowctl Client - Open two sockets close one Not Run L2CAP LE ATT Client - Success Passed 0.015 seconds L2CAP LE ATT Server - Success Passed 0.016 seconds
Total: 40, Passed: 34 (85.0%), Failed: 0, Not Run: 6 Overall execution time: 0.985 seconds Process 38 exited with status 0
reboot: Restarting system
c[?7l[2JSeaBIOS (version 1.13.0-1ubuntu1.1) Booting from ROM..c[?7l[2Jearly console in extract_kernelinput_data: 0x0000000001e732e0input_len: 0x00000000003532f3
output: 0x0000000001000000output_len: 0x00000000011944cckernel_total_size: 0x0000000001030000needed_size: 0x0000000001200000trampoline_32bit: 0x000000000009d000
Physical KASLR using RDTSC...
Virtual KASLR using RDTSC...
Decompressing Linux... Parsing ELF... Performing relocations... done.
Booting the kernel.
Linux version 5.11.0-g4174e7ab9aee (root@b391cbe99e1a) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #2 Mon Apr 5 21:09:20 UTC 2021
Command line: console=ttyS0,115200n8 earlyprintk=serial rootfstype=9p rootflags=trans=virtio,version=9p2000.L acpi=off pci=noacpi noapic quiet ro init=/github/workspace/bluez/tools/test-runner TESTHOME=/github/workspace TESTDBUS=0 TESTMONITOR=0 TESTDEVS=0 TESTAUTO=0 TESTARGS='/github/workspace/bluez/tools/bnep-tester' x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000000bffdfff] usable
BIOS-e820: [mem 0x000000000bffe000-0x000000000bffffff] reserved
BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
printk: bootconsole [earlyser0] enabled
Memory KASLR using RDTSC...
Poking KASLR using RDTSC...
Mounting sysfs to /sys
Mounting proc to /proc
Mounting devtmpfs to /dev
Creating /dev/pts
Mounting devpts to /dev/pts
Creating /dev/shm
Mounting tmpfs to /dev/shm
Mounting tmpfs to /run
Mounting tmpfs to /tmp
Mounting debugfs to /sys/kernel/debug
Linking /dev/fd to /proc/self/fd
Linking /dev/stdin to /proc/self/fd/0
Linking /dev/stdout to /proc/self/fd/1
Linking /dev/stderr to /proc/self/fd/2
Creating new session group leader
Setting controlling terminal
Creating /var/lib/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/dbus-1
Failed to create filesystem: No such file or directory
Creating /usr/share/dbus-1
Running command /github/workspace/bluez/tools/bnep-tester
New process 38 created
Changing into directory /github/workspace
Basic BNEP Socket - Success - init
Read Index List callback
Status: 0x00
New hciemu instance created
Index Added callback
Index: 0x0000
Read Info callback
Status: 0x00
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Basic BNEP Socket - Success - setup
Powering on controller
Controller powered on
Client set connectable status 0x00
Basic BNEP Socket - Success - setup complete
Basic BNEP Socket - Success - run
Basic BNEP Socket - Success - test passed
Basic BNEP Socket - Success - teardown
Index Removed callback
Index: 0x0000
Basic BNEP Socket - Success - teardown complete
Basic BNEP Socket - Success - done
Test Summary
------------
Basic BNEP Socket - Success Passed 0.060 seconds
Total: 1, Passed: 1 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.068 seconds Process 38 exited with status 0
reboot: Restarting system
c[?7l[2JSeaBIOS (version 1.13.0-1ubuntu1.1) Booting from ROM..c[?7l[2Jearly console in extract_kernelinput_data: 0x0000000001e732e0input_len: 0x00000000003532f3
output: 0x0000000001000000output_len: 0x00000000011944cckernel_total_size: 0x0000000001030000needed_size: 0x0000000001200000trampoline_32bit: 0x000000000009d000
Physical KASLR using RDTSC...
Virtual KASLR using RDTSC...
Decompressing Linux... Parsing ELF... Performing relocations... done.
Booting the kernel.
Linux version 5.11.0-g4174e7ab9aee (root@b391cbe99e1a) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #2 Mon Apr 5 21:09:20 UTC 2021
Command line: console=ttyS0,115200n8 earlyprintk=serial rootfstype=9p rootflags=trans=virtio,version=9p2000.L acpi=off pci=noacpi noapic quiet ro init=/github/workspace/bluez/tools/test-runner TESTHOME=/github/workspace TESTDBUS=0 TESTMONITOR=0 TESTDEVS=0 TESTAUTO=0 TESTARGS='/github/workspace/bluez/tools/mgmt-tester' x86/fpu: x87 FPU will use FXSAVE
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000000bffdfff] usable
BIOS-e820: [mem 0x000000000bffe000-0x000000000bffffff] reserved
BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
printk: bootconsole [earlyser0] enabled
Memory KASLR using RDTSC...
Poking KASLR using RDTSC...
Mounting sysfs to /sys
Mounting proc to /proc
Mounting devtmpfs to /dev
Creating /dev/pts
Mounting devpts to /dev/pts
Creating /dev/shm
Mounting tmpfs to /dev/shm
Mounting tmpfs to /run
Mounting tmpfs to /tmp
Mounting debugfs to /sys/kernel/debug
Linking /dev/fd to /proc/self/fd
Linking /dev/stdin to /proc/self/fd/0
Linking /dev/stdout to /proc/self/fd/1
Linking /dev/stderr to /proc/self/fd/2
Creating new session group leader
Setting controlling terminal
Creating /var/lib/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/bluetooth
Failed to create filesystem: No such file or directory
Creating /etc/dbus-1
Failed to create filesystem: No such file or directory
Creating /usr/share/dbus-1
Running command /github/workspace/bluez/tools/mgmt-tester
New process 38 created
Changing into directory /github/workspace
Controller setup - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Controller setup - setup
Controller setup - setup complete
Controller setup - run
Controller setup - test passed
Controller setup - teardown
Index Removed callback
Index: 0x0000
Controller setup - teardown complete
Controller setup - done
Controller setup (BR/EDR-only) - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Controller setup (BR/EDR-only) - setup
Controller setup (BR/EDR-only) - setup complete
Controller setup (BR/EDR-only) - run
Controller setup (BR/EDR-only) - test passed
Controller setup (BR/EDR-only) - teardown
Index Removed callback
Index: 0x0000
Controller setup (BR/EDR-only) - teardown complete Controller setup (BR/EDR-only) - done
Controller setup (LE) - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Controller setup (LE) - setup
Controller setup (LE) - setup complete
Controller setup (LE) - run
Controller setup (LE) - test passed
Controller setup (LE) - teardown
Index Removed callback
Index: 0x0000
Controller setup (LE) - teardown complete
Controller setup (LE) - done
Invalid command - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Invalid command - setup
Invalid command - setup complete
Invalid command - run
Sending <unknown opcode> (0xffff)
Test condition added, total 1
<unknown opcode> (0xffff): Unknown Command (0x01) Test condition complete, 0 left
Invalid command - test passed
Invalid command - teardown
Index Removed callback
Index: 0x0000
Invalid command - teardown complete
Invalid command - done
Read version - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read version - Success - setup
Read version - Success - setup complete
Read version - Success - run
Sending Read Version (0x0001)
Test condition added, total 1
Read Version (0x0001): Success (0x00)
Test condition complete, 0 left
Read version - Success - test passed
Read version - Success - teardown
Index Removed callback
Index: 0x0000
Read version - Success - teardown complete
Read version - Success - done
Read version - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read version - Invalid parameters - setup Read version - Invalid parameters - setup complete Read version - Invalid parameters - run
Sending Read Version (0x0001)
Test condition added, total 1
Read Version (0x0001): Invalid Parameters (0x0d) Test condition complete, 0 left
Read version - Invalid parameters - test passed Read version - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read version - Invalid parameters - teardown complete Read version - Invalid parameters - done
Read version - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read version - Invalid index - setup
Read version - Invalid index - setup complete
Read version - Invalid index - run
Sending Read Version (0x0001)
Test condition added, total 1
Read Version (0x0001): Invalid Index (0x11)
Test condition complete, 0 left
Read version - Invalid index - test passed
Read version - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read version - Invalid index - teardown complete
Read version - Invalid index - done
Read commands - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read commands - Invalid parameters - setup Read commands - Invalid parameters - setup complete Read commands - Invalid parameters - run
Sending Read Commands (0x0002)
Test condition added, total 1
Read Commands (0x0002): Invalid Parameters (0x0d) Test condition complete, 0 left
Read commands - Invalid parameters - test passed Read commands - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read commands - Invalid parameters - teardown complete Read commands - Invalid parameters - done
Read commands - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read commands - Invalid index - setup
Read commands - Invalid index - setup complete
Read commands - Invalid index - run
Sending Read Commands (0x0002)
Test condition added, total 1
Read Commands (0x0002): Invalid Index (0x11)
Test condition complete, 0 left
Read commands - Invalid index - test passed
Read commands - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read commands - Invalid index - teardown complete
Read commands - Invalid index - done
Read index list - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read index list - Invalid parameters - setup Read index list - Invalid parameters - setup complete Read index list - Invalid parameters - run
Sending Read Index List (0x0003)
Test condition added, total 1
Read Index List (0x0003): Invalid Parameters (0x0d) Test condition complete, 0 left
Read index list - Invalid parameters - test passed Read index list - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read index list - Invalid parameters - teardown complete Read index list - Invalid parameters - done
Read index list - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read index list - Invalid index - setup
Read index list - Invalid index - setup complete
Read index list - Invalid index - run
Sending Read Index List (0x0003)
Test condition added, total 1
Read Index List (0x0003): Invalid Index (0x11)
Test condition complete, 0 left
Read index list - Invalid index - test passed
Read index list - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read index list - Invalid index - teardown complete Read index list - Invalid index - done
Read info - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read info - Invalid parameters - setup
Read info - Invalid parameters - setup complete Read info - Invalid parameters - run
Sending Read Controller Info (0x0004)
Test condition added, total 1
Read Controller Info (0x0004): Invalid Parameters (0x0d) Test condition complete, 0 left
Read info - Invalid parameters - test passed
Read info - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read info - Invalid parameters - teardown complete Read info - Invalid parameters - done
Read info - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read info - Invalid index - setup
Read info - Invalid index - setup complete Read info - Invalid index - run
Sending Read Controller Info (0x0004)
Test condition added, total 1
Read Controller Info (0x0004): Invalid Index (0x11) Test condition complete, 0 left
Read info - Invalid index - test passed
Read info - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read info - Invalid index - teardown complete
Read info - Invalid index - done
Read unconfigured index list - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read unconfigured index list - Invalid parameters - setup Read unconfigured index list - Invalid parameters - setup complete Read unconfigured index list - Invalid parameters - run
Sending Read Unconfigured Index List (0x0036)
Test condition added, total 1
Read Unconfigured Index List (0x0036): Invalid Parameters (0x0d) Test condition complete, 0 left
Read unconfigured index list - Invalid parameters - test passed Read unconfigured index list - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read unconfigured index list - Invalid parameters - teardown complete Read unconfigured index list - Invalid parameters - done
Read unconfigured index list - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read unconfigured index list - Invalid index - setup Read unconfigured index list - Invalid index - setup complete Read unconfigured index list - Invalid index - run
Sending Read Unconfigured Index List (0x0036) Test condition added, total 1
Read Unconfigured Index List (0x0036): Invalid Index (0x11) Test condition complete, 0 left
Read unconfigured index list - Invalid index - test passed Read unconfigured index list - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read unconfigured index list - Invalid index - teardown complete Read unconfigured index list - Invalid index - done
Read configuration info - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read configuration info - Invalid parameters - setup
Read configuration info - Invalid parameters - setup complete
Read configuration info - Invalid parameters - run
Sending Read Controller Configuration Information (0x0037)
Test condition added, total 1
Read Controller Configuration Information (0x0037): Invalid Parameters (0x0d) Test condition complete, 0 left
Read configuration info - Invalid parameters - test passed
Read configuration info - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read configuration info - Invalid parameters - teardown complete Read configuration info - Invalid parameters - done
Read configuration info - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read configuration info - Invalid index - setup
Read configuration info - Invalid index - setup complete
Read configuration info - Invalid index - run
Sending Read Controller Configuration Information (0x0037) Test condition added, total 1
Read Controller Configuration Information (0x0037): Invalid Index (0x11) Test condition complete, 0 left
Read configuration info - Invalid index - test passed
Read configuration info - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read configuration info - Invalid index - teardown complete Read configuration info - Invalid index - done
Read extended index list - Invalid parameters - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read extended index list - Invalid parameters - setup
Read extended index list - Invalid parameters - setup complete Read extended index list - Invalid parameters - run
Sending Read Extended Controller Index List (0x003c)
Test condition added, total 1
Read Extended Controller Index List (0x003c): Invalid Parameters (0x0d) Test condition complete, 0 left
Read extended index list - Invalid parameters - test passed Read extended index list - Invalid parameters - teardown
Index Removed callback
Index: 0x0000
Read extended index list - Invalid parameters - teardown complete Read extended index list - Invalid parameters - done
Read extended index list - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Read extended index list - Invalid index - setup
Read extended index list - Invalid index - setup complete Read extended index list - Invalid index - run
Sending Read Extended Controller Index List (0x003c) Test condition added, total 1
Read Extended Controller Index List (0x003c): Invalid Index (0x11) Test condition complete, 0 left
Read extended index list - Invalid index - test passed Read extended index list - Invalid index - teardown
Index Removed callback
Index: 0x0000
Read extended index list - Invalid index - teardown complete Read extended index list - Invalid index - done
Set powered on - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Success - setup
Set powered on - Success - setup complete
Set powered on - Success - run
Registering new settings notification
Test condition added, total 1
Sending Set Powered (0x0005)
Test condition added, total 2
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set powered on - Success - test passed
Set powered on - Success - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set powered on - Success - teardown complete
Set powered on - Success - done
Set powered on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid parameters 1 - setup Set powered on - Invalid parameters 1 - setup complete Set powered on - Invalid parameters 1 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered on - Invalid parameters 1 - test passed Set powered on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid parameters 1 - teardown complete Set powered on - Invalid parameters 1 - done
Set powered on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid parameters 2 - setup Set powered on - Invalid parameters 2 - setup complete Set powered on - Invalid parameters 2 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered on - Invalid parameters 2 - test passed Set powered on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid parameters 2 - teardown complete Set powered on - Invalid parameters 2 - done
Set powered on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid parameters 3 - setup Set powered on - Invalid parameters 3 - setup complete Set powered on - Invalid parameters 3 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered on - Invalid parameters 3 - test passed Set powered on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid parameters 3 - teardown complete Set powered on - Invalid parameters 3 - done
Set powered on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered on - Invalid index - setup
Set powered on - Invalid index - setup complete
Set powered on - Invalid index - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Index (0x11)
Test condition complete, 0 left
Set powered on - Invalid index - test passed
Set powered on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set powered on - Invalid index - teardown complete Set powered on - Invalid index - done
Set powered on - Privacy and Advertising - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set powered on - Privacy and Advertising - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered on - Privacy and Advertising - setup complete Set powered on - Privacy and Advertising - run
Sending Set Advertising (0x0029)
Test condition added, total 1
Set Advertising (0x0029): Success (0x00)
Test condition complete, 0 left
Set powered on - Privacy and Advertising - test passed Set powered on - Privacy and Advertising - teardown
Index Removed callback
Index: 0x0000
Set powered on - Privacy and Advertising - teardown complete Set powered on - Privacy and Advertising - done
Set powered off - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Success - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Success - setup complete
Set powered off - Success - run
Registering new settings notification
Test condition added, total 1
Sending Set Powered (0x0005)
Test condition added, total 2
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x00000080 received
Unregistering new settings notification
Test condition complete, 0 left
Set powered off - Success - test passed
Set powered off - Success - teardown
Index Removed callback
Index: 0x0000
Set powered off - Success - teardown complete
Set powered off - Success - done
Set powered off - Class of Device - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Class of Device - setup
Setting device class and powering on Controller powered on
Client set connectable: Success (0x00)
Set powered off - Class of Device - setup complete Set powered off - Class of Device - run
Registering new settings notification Test condition added, total 1 Registering Class of Device Changed notification Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
Set Powered (0x0005): Success (0x00) Test condition complete, 2 left
New Class of Device Changed event received Test condition complete, 1 left
New settings 0x00000080 received Unregistering new settings notification Test condition complete, 0 left
Set powered off - Class of Device - test passed Set powered off - Class of Device - teardown
Index Removed callback
Index: 0x0000
Set powered off - Class of Device - teardown complete Set powered off - Class of Device - done
Set powered off - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Invalid parameters 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Invalid parameters 1 - setup complete Set powered off - Invalid parameters 1 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered off - Invalid parameters 1 - test passed Set powered off - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set powered off - Invalid parameters 1 - teardown complete Set powered off - Invalid parameters 1 - done
Set powered off - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Invalid parameters 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Invalid parameters 2 - setup complete Set powered off - Invalid parameters 2 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered off - Invalid parameters 2 - test passed Set powered off - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set powered off - Invalid parameters 2 - teardown complete Set powered off - Invalid parameters 2 - done
Set powered off - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set powered off - Invalid parameters 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set powered off - Invalid parameters 3 - setup complete Set powered off - Invalid parameters 3 - run
Sending Set Powered (0x0005)
Test condition added, total 1
Set Powered (0x0005): Invalid Parameters (0x0d) Test condition complete, 0 left
Set powered off - Invalid parameters 3 - test passed Set powered off - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set powered off - Invalid parameters 3 - teardown complete Set powered off - Invalid parameters 3 - done
Set connectable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Success 1 - setup
Set connectable on - Success 1 - setup complete
Set connectable on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000082 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable on - Success 1 - test passed
Set connectable on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Success 1 - teardown complete Set connectable on - Success 1 - done
Set connectable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable on - Success 2 - setup complete
Set connectable on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000083 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable on - Success 2 - test passed
Set connectable on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable on - Success 2 - teardown complete Set connectable on - Success 2 - done
Set connectable on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid parameters 1 - setup Set connectable on - Invalid parameters 1 - setup complete Set connectable on - Invalid parameters 1 - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Parameters (0x0d) Test condition complete, 0 left
Set connectable on - Invalid parameters 1 - test passed Set connectable on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid parameters 1 - teardown complete Set connectable on - Invalid parameters 1 - done
Set connectable on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid parameters 2 - setup Set connectable on - Invalid parameters 2 - setup complete Set connectable on - Invalid parameters 2 - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Parameters (0x0d) Test condition complete, 0 left
Set connectable on - Invalid parameters 2 - test passed Set connectable on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid parameters 2 - teardown complete Set connectable on - Invalid parameters 2 - done
Set connectable on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid parameters 3 - setup Set connectable on - Invalid parameters 3 - setup complete Set connectable on - Invalid parameters 3 - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Parameters (0x0d) Test condition complete, 0 left
Set connectable on - Invalid parameters 3 - test passed Set connectable on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid parameters 3 - teardown complete Set connectable on - Invalid parameters 3 - done
Set connectable on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable on - Invalid index - setup Set connectable on - Invalid index - setup complete Set connectable on - Invalid index - run
Sending Set Connectable (0x0007)
Test condition added, total 1
Set Connectable (0x0007): Invalid Index (0x11) Test condition complete, 0 left
Set connectable on - Invalid index - test passed Set connectable on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set connectable on - Invalid index - teardown complete Set connectable on - Invalid index - done
Set connectable on (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable on (LE) - Success 1 - setup Set connectable on (LE) - Success 1 - setup complete Set connectable on (LE) - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000202 received Unregistering new settings notification Test condition complete, 0 left
Set connectable on (LE) - Success 1 - test passed Set connectable on (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable on (LE) - Success 1 - teardown complete Set connectable on (LE) - Success 1 - done
Set connectable on (LE) - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable on (LE) - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable on (LE) - Success 2 - setup complete Set connectable on (LE) - Success 2 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000203 received Unregistering new settings notification Test condition complete, 0 left
Set connectable on (LE) - Success 2 - test passed Set connectable on (LE) - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable on (LE) - Success 2 - teardown complete Set connectable on (LE) - Success 2 - done
Set connectable on (LE) - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable on (LE) - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable on (LE) - Success 3 - setup complete Set connectable on (LE) - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x200a length 1
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000603 received Unregistering new settings notification Test condition complete, 0 left
Set connectable on (LE) - Success 3 - test passed Set connectable on (LE) - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable on (LE) - Success 3 - teardown complete Set connectable on (LE) - Success 3 - done
Set connectable off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off - Success 1 - setup complete
Set connectable off - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000080 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 1 - test passed
Set connectable off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable off - Success 1 - teardown complete Set connectable off - Success 1 - done
Set connectable off - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off - Success 2 - setup complete
Set connectable off - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 2 - test passed
Set connectable off - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off - Success 2 - teardown complete Set connectable off - Success 2 - done
Set connectable off - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off - Success 3 - setup complete
Set connectable off - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 3 - test passed
Set connectable off - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off - Success 3 - teardown complete Set connectable off - Success 3 - done
Set connectable off - Success 4 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set connectable off - Success 4 - setup
Initial settings completed
Powering on controller (with added device)
Controller powered on
Client set connectable: Success (0x00)
Set connectable off - Success 4 - setup complete
Set connectable off - Success 4 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Connectable (0x0007): Success (0x00)
Test condition complete, 1 left
New settings 0x00000081 received
Unregistering new settings notification
Test condition complete, 0 left
Set connectable off - Success 4 - test passed
Set connectable off - Success 4 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off - Success 4 - teardown complete Set connectable off - Success 4 - done
Set connectable off (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 1 - setup complete Set connectable off (LE) - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Connectable (0x0007)
Test condition added, total 2
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000200 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 1 - test passed Set connectable off (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 1 - teardown complete Set connectable off (LE) - Success 1 - done
Set connectable off (LE) - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 2 - setup complete Set connectable off (LE) - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x200a length 1
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000601 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 2 - test passed Set connectable off (LE) - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 2 - teardown complete Set connectable off (LE) - Success 2 - done
Set connectable off (LE) - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 3 - setup complete Set connectable off (LE) - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x2008 length 32
HCI Command 0x200a length 1
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000601 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 3 - test passed Set connectable off (LE) - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 3 - teardown complete Set connectable off (LE) - Success 3 - done
Set connectable off (LE) - Success 4 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set connectable off (LE) - Success 4 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set connectable off (LE) - Success 4 - setup complete Set connectable off (LE) - Success 4 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Connectable (0x0007)
Test condition added, total 3
HCI Command 0x2008 length 32
HCI Command 0x200a length 1
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
Test condition complete, 2 left
HCI Command 0x200a length 1
Set Connectable (0x0007): Success (0x00) Test condition complete, 1 left
New settings 0x00000601 received Unregistering new settings notification Test condition complete, 0 left
Set connectable off (LE) - Success 4 - test passed Set connectable off (LE) - Success 4 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set connectable off (LE) - Success 4 - teardown complete Set connectable off (LE) - Success 4 - done
Set fast connectable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set fast connectable on - Success 1 - setup complete Set fast connectable on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Fast Connectable (0x0008)
Test condition added, total 2
Set Fast Connectable (0x0008): Success (0x00) Test condition complete, 1 left
New settings 0x00000087 received Unregistering new settings notification Test condition complete, 0 left
Set fast connectable on - Success 1 - test passed Set fast connectable on - Success 1 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set fast connectable on - Success 1 - teardown complete Set fast connectable on - Success 1 - done
Set fast connectable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set fast connectable on - Success 2 - setup complete Set fast connectable on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Sending Set Fast Connectable (0x0008)
Test condition added, total 2
Set Fast Connectable (0x0008): Success (0x00) Test condition complete, 1 left
New settings 0x00000085 received Unregistering new settings notification Test condition complete, 0 left
Set fast connectable on - Success 2 - test passed Set fast connectable on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set fast connectable on - Success 2 - teardown complete Set fast connectable on - Success 2 - done
Set fast connectable on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Success 3 - setup Set fast connectable on - Success 3 - setup complete Set fast connectable on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Sending Set Fast Connectable (0x0008)
Test condition added, total 2
Set Fast Connectable (0x0008): Success (0x00) Test condition complete, 1 left
New settings 0x00000084 received Unregistering new settings notification Test condition complete, 0 left
Set fast connectable on - Success 3 - test passed Set fast connectable on - Success 3 - teardown
Index Removed callback
Index: 0x0000
Set fast connectable on - Success 3 - teardown complete Set fast connectable on - Success 3 - done
Set fast connectable on - Invalid Params 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set fast connectable on - Invalid Params 1 - setup Set fast connectable on - Invalid Params 1 - setup complete Set fast connectable on - Invalid Params 1 - run
Sending Set Fast Connectable (0x0008)
Test condition added, total 1
Set Fast Connectable (0x0008): Invalid Parameters (0x0d) Test condition complete, 0 left
Set fast connectable on - Invalid Params 1 - test passed Set fast connectable on - Invalid Params 1 - teardown
Index Removed callback
Index: 0x0000
Set fast connectable on - Invalid Params 1 - teardown complete Set fast connectable on - Invalid Params 1 - done
Set fast connectable on - Not Supported 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set fast connectable on - Not Supported 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set fast connectable on - Not Supported 1 - setup complete Set fast connectable on - Not Supported 1 - run
Sending Set Fast Connectable (0x0008)
Test condition added, total 1
Set Fast Connectable (0x0008): Not Supported (0x0c) Test condition complete, 0 left
Set fast connectable on - Not Supported 1 - test passed Set fast connectable on - Not Supported 1 - teardown
Index Removed callback
Index: 0x0000
Set fast connectable on - Not Supported 1 - teardown complete Set fast connectable on - Not Supported 1 - done
Set bondable on - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Success - setup
Set bondable on - Success - setup complete
Set bondable on - Success - run
Registering new settings notification
Test condition added, total 1
Sending Set Bondable (0x0009)
Test condition added, total 2
Set Bondable (0x0009): Success (0x00)
Test condition complete, 1 left
New settings 0x00000090 received
Unregistering new settings notification
Test condition complete, 0 left
Set bondable on - Success - test passed
Set bondable on - Success - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Success - teardown complete
Set bondable on - Success - done
Set bondable on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid parameters 1 - setup Set bondable on - Invalid parameters 1 - setup complete Set bondable on - Invalid parameters 1 - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Parameters (0x0d) Test condition complete, 0 left
Set bondable on - Invalid parameters 1 - test passed Set bondable on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid parameters 1 - teardown complete Set bondable on - Invalid parameters 1 - done
Set bondable on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid parameters 2 - setup Set bondable on - Invalid parameters 2 - setup complete Set bondable on - Invalid parameters 2 - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Parameters (0x0d) Test condition complete, 0 left
Set bondable on - Invalid parameters 2 - test passed Set bondable on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid parameters 2 - teardown complete Set bondable on - Invalid parameters 2 - done
Set bondable on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid parameters 3 - setup Set bondable on - Invalid parameters 3 - setup complete Set bondable on - Invalid parameters 3 - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Parameters (0x0d) Test condition complete, 0 left
Set bondable on - Invalid parameters 3 - test passed Set bondable on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid parameters 3 - teardown complete Set bondable on - Invalid parameters 3 - done
Set bondable on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set bondable on - Invalid index - setup
Set bondable on - Invalid index - setup complete
Set bondable on - Invalid index - run
Sending Set Bondable (0x0009)
Test condition added, total 1
Set Bondable (0x0009): Invalid Index (0x11)
Test condition complete, 0 left
Set bondable on - Invalid index - test passed
Set bondable on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set bondable on - Invalid index - teardown complete Set bondable on - Invalid index - done
Set discoverable on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 1 - setup Set discoverable on - Invalid parameters 1 - setup complete Set discoverable on - Invalid parameters 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 1 - test passed Set discoverable on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 1 - teardown complete Set discoverable on - Invalid parameters 1 - done
Set discoverable on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 2 - setup Set discoverable on - Invalid parameters 2 - setup complete Set discoverable on - Invalid parameters 2 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 2 - test passed Set discoverable on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 2 - teardown complete Set discoverable on - Invalid parameters 2 - done
Set discoverable on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 3 - setup Set discoverable on - Invalid parameters 3 - setup complete Set discoverable on - Invalid parameters 3 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 3 - test passed Set discoverable on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 3 - teardown complete Set discoverable on - Invalid parameters 3 - done
Set discoverable on - Invalid parameters 4 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Invalid parameters 4 - setup Set discoverable on - Invalid parameters 4 - setup complete Set discoverable on - Invalid parameters 4 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Invalid Parameters (0x0d) Test condition complete, 0 left
Set discoverable on - Invalid parameters 4 - test passed Set discoverable on - Invalid parameters 4 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Invalid parameters 4 - teardown complete Set discoverable on - Invalid parameters 4 - done
Set discoverable on - Not powered 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Not powered 1 - setup Set discoverable on - Not powered 1 - setup complete Set discoverable on - Not powered 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Not Powered (0x0f) Test condition complete, 0 left
Set discoverable on - Not powered 1 - test passed Set discoverable on - Not powered 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Not powered 1 - teardown complete Set discoverable on - Not powered 1 - done
Set discoverable on - Not powered 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Not powered 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Not powered 2 - setup complete Set discoverable on - Not powered 2 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Not Powered (0x0f) Test condition complete, 0 left
Set discoverable on - Not powered 2 - test passed Set discoverable on - Not powered 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Not powered 2 - teardown complete Set discoverable on - Not powered 2 - done
Set discoverable on - Rejected 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Rejected 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Rejected 1 - setup complete
Set discoverable on - Rejected 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Rejected (0x0b)
Test condition complete, 0 left
Set discoverable on - Rejected 1 - test passed
Set discoverable on - Rejected 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Rejected 1 - teardown complete Set discoverable on - Rejected 1 - done
Set discoverable on - Rejected 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Rejected 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Rejected 2 - setup complete
Set discoverable on - Rejected 2 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Rejected (0x0b)
Test condition complete, 0 left
Set discoverable on - Rejected 2 - test passed
Set discoverable on - Rejected 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Rejected 2 - teardown complete Set discoverable on - Rejected 2 - done
Set discoverable on - Rejected 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Rejected 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Rejected 3 - setup complete
Set discoverable on - Rejected 3 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Rejected (0x0b)
Test condition complete, 0 left
Set discoverable on - Rejected 3 - test passed
Set discoverable on - Rejected 3 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Rejected 3 - teardown complete Set discoverable on - Rejected 3 - done
Set discoverable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Success 1 - setup complete
Set discoverable on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 1 left
New settings 0x0000008a received
Unregistering new settings notification
Test condition complete, 0 left
Set discoverable on - Success 1 - test passed
Set discoverable on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on - Success 1 - teardown complete Set discoverable on - Success 1 - done
Set discoverable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on - Success 2 - setup complete
Set discoverable on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Discoverable (0x0006)
Test condition added, total 3
HCI Command 0x0c3a length 4
HCI Command 0x0c1a length 1
Test condition complete, 2 left
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 1 left
New settings 0x0000008b received
Unregistering new settings notification
Test condition complete, 0 left
Set discoverable on - Success 2 - test passed
Set discoverable on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set discoverable on - Success 2 - teardown complete Set discoverable on - Success 2 - done
Set discoverable on (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set discoverable on (LE) - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable on (LE) - Success 1 - setup complete Set discoverable on (LE) - Success 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x2008 length 32
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set discoverable on (LE) - Success 1 - test passed Set discoverable on (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable on (LE) - Success 1 - teardown complete Set discoverable on (LE) - Success 1 - done
Set discoverable off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable off - Success 1 - setup complete
Set discoverable off - Success 1 - run
Sending Set Discoverable (0x0006)
Test condition added, total 1
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 0 left
Set discoverable off - Success 1 - test passed
Set discoverable off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set discoverable off - Success 1 - teardown complete Set discoverable off - Success 1 - done
Set discoverable off - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set discoverable off - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set discoverable off - Success 2 - setup complete
Set discoverable off - Success 2 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c1a length 1
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 0 left
Set discoverable off - Success 2 - test passed
Set discoverable off - Success 2 - teardown
Index Removed callback
Index: 0x0000
Set discoverable off - Success 2 - teardown complete Set discoverable off - Success 2 - done
Set limited discoverable on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set limited discoverable on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on - Success 1 - setup complete Set limited discoverable on - Success 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c3a length 4
HCI Command 0x0c1a length 1
Test condition complete, 1 left
HCI Command 0x0c24 length 3
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set limited discoverable on - Success 1 - test passed Set limited discoverable on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on - Success 1 - teardown complete Set limited discoverable on - Success 1 - done
Set limited discoverable on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set limited discoverable on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on - Success 2 - setup complete Set limited discoverable on - Success 2 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c3a length 4
Test condition complete, 1 left
HCI Command 0x0c1a length 1
HCI Command 0x0c24 length 3
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set limited discoverable on - Success 2 - test passed Set limited discoverable on - Success 2 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on - Success 2 - teardown complete Set limited discoverable on - Success 2 - done
Set limited discoverable on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set limited discoverable on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on - Success 3 - setup complete Set limited discoverable on - Success 3 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x0c3a length 4
HCI Command 0x0c1a length 1
HCI Command 0x0c24 length 3
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00) Test condition complete, 0 left
Set limited discoverable on - Success 3 - test passed Set limited discoverable on - Success 3 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on - Success 3 - teardown complete Set limited discoverable on - Success 3 - done
Set limited discoverable on (LE) - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001be1b
Current settings: 0x00000200
Class: 0x000000
Name:
Short name: Set limited discoverable on (LE) - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set limited discoverable on (LE) - Success 1 - setup complete Set limited discoverable on (LE) - Success 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Discoverable (0x0006)
Test condition added, total 2
HCI Command 0x2008 length 32
Test condition complete, 1 left
Set Discoverable (0x0006): Success (0x00)
Test condition complete, 0 left
Set limited discoverable on (LE) - Success 1 - test passed Set limited discoverable on (LE) - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set limited discoverable on (LE) - Success 1 - teardown complete Set limited discoverable on (LE) - Success 1 - done
Set link security on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Success 1 - setup
Set link security on - Success 1 - setup complete
Set link security on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Link Security (0x000a)
Test condition added, total 2
Set Link Security (0x000a): Success (0x00)
Test condition complete, 1 left
New settings 0x000000a0 received
Unregistering new settings notification
Test condition complete, 0 left
Set link security on - Success 1 - test passed
Set link security on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Success 1 - teardown complete Set link security on - Success 1 - done
Set link security on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security on - Success 2 - setup complete
Set link security on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Link Security (0x000a)
Test condition added, total 3
HCI Command 0x0c20 length 1
Test condition complete, 2 left
Set Link Security (0x000a): Success (0x00)
Test condition complete, 1 left
New settings 0x000000a1 received
Unregistering new settings notification
Test condition complete, 0 left
Set link security on - Success 2 - test passed
Set link security on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set link security on - Success 2 - teardown complete Set link security on - Success 2 - done
Set link security on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security on - Success 3 - setup complete
Set link security on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
HCI Command 0x0c20 length 1
Test condition complete, 2 left
HCI Command 0x0c13 length 248
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x000000a1 received
Unregistering new settings notification
Test condition complete, 0 left
Set link security on - Success 3 - test passed
Set link security on - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set link security on - Success 3 - teardown complete Set link security on - Success 3 - done
Set link security on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid parameters 1 - setup Set link security on - Invalid parameters 1 - setup complete Set link security on - Invalid parameters 1 - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Parameters (0x0d) Test condition complete, 0 left
Set link security on - Invalid parameters 1 - test passed Set link security on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid parameters 1 - teardown complete Set link security on - Invalid parameters 1 - done
Set link security on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid parameters 2 - setup Set link security on - Invalid parameters 2 - setup complete Set link security on - Invalid parameters 2 - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Parameters (0x0d) Test condition complete, 0 left
Set link security on - Invalid parameters 2 - test passed Set link security on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid parameters 2 - teardown complete Set link security on - Invalid parameters 2 - done
Set link security on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid parameters 3 - setup Set link security on - Invalid parameters 3 - setup complete Set link security on - Invalid parameters 3 - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Parameters (0x0d) Test condition complete, 0 left
Set link security on - Invalid parameters 3 - test passed Set link security on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid parameters 3 - teardown complete Set link security on - Invalid parameters 3 - done
Set link security on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security on - Invalid index - setup Set link security on - Invalid index - setup complete Set link security on - Invalid index - run
Sending Set Link Security (0x000a)
Test condition added, total 1
Set Link Security (0x000a): Invalid Index (0x11) Test condition complete, 0 left
Set link security on - Invalid index - test passed Set link security on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set link security on - Invalid index - teardown complete Set link security on - Invalid index - done
Set link security off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security off - Success 1 - setup complete Set link security off - Success 1 - run
Registering new settings notification Test condition added, total 1
Sending Set Link Security (0x000a)
Test condition added, total 2
Set Link Security (0x000a): Success (0x00) Test condition complete, 1 left
New settings 0x00000080 received Unregistering new settings notification Test condition complete, 0 left
Set link security off - Success 1 - test passed Set link security off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set link security off - Success 1 - teardown complete Set link security off - Success 1 - done
Set link security off - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set link security off - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set link security off - Success 2 - setup complete Set link security off - Success 2 - run
Registering new settings notification Test condition added, total 1 Registering HCI command callback
Test condition added, total 2
Sending Set Link Security (0x000a)
Test condition added, total 3
HCI Command 0x0c20 length 1
Test condition complete, 2 left
Set Link Security (0x000a): Success (0x00) Test condition complete, 1 left
New settings 0x00000081 received Unregistering new settings notification Test condition complete, 0 left
Set link security off - Success 2 - test passed Set link security off - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set link security off - Success 2 - teardown complete Set link security off - Success 2 - done
Set SSP on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Success 1 - setup
Set SSP on - Success 1 - setup complete
Set SSP on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Secure Simple Pairing (0x000b) Test condition added, total 2
Set Secure Simple Pairing (0x000b): Success (0x00) Test condition complete, 1 left
New settings 0x000000c0 received Unregistering new settings notification Test condition complete, 0 left
Set SSP on - Success 1 - test passed
Set SSP on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Success 1 - teardown complete
Set SSP on - Success 1 - done
Set SSP on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set SSP on - Success 2 - setup complete
Set SSP on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Secure Simple Pairing (0x000b) Test condition added, total 3
HCI Command 0x0c56 length 1
Test condition complete, 2 left
Set Secure Simple Pairing (0x000b): Success (0x00) Test condition complete, 1 left
New settings 0x000000c1 received Unregistering new settings notification Test condition complete, 0 left
Set SSP on - Success 2 - test passed
HCI Command 0x0c52 length 241
Set SSP on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set SSP on - Success 2 - teardown complete
Set SSP on - Success 2 - done
Set SSP on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set SSP on - Success 3 - setup complete
Set SSP on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
HCI Command 0x0c56 length 1
Test condition complete, 2 left
HCI Command 0x0c13 length 248
HCI Command 0x0c52 length 241
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x000000c1 received
Unregistering new settings notification
Test condition complete, 0 left
Set SSP on - Success 3 - test passed
Set SSP on - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set SSP on - Success 3 - teardown complete
Set SSP on - Success 3 - done
Set SSP on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid parameters 1 - setup
Set SSP on - Invalid parameters 1 - setup complete Set SSP on - Invalid parameters 1 - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Parameters (0x0d) Test condition complete, 0 left
Set SSP on - Invalid parameters 1 - test passed
Set SSP on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid parameters 1 - teardown complete Set SSP on - Invalid parameters 1 - done
Set SSP on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid parameters 2 - setup
Set SSP on - Invalid parameters 2 - setup complete Set SSP on - Invalid parameters 2 - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Parameters (0x0d) Test condition complete, 0 left
Set SSP on - Invalid parameters 2 - test passed
Set SSP on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid parameters 2 - teardown complete Set SSP on - Invalid parameters 2 - done
Set SSP on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid parameters 3 - setup
Set SSP on - Invalid parameters 3 - setup complete Set SSP on - Invalid parameters 3 - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Parameters (0x0d) Test condition complete, 0 left
Set SSP on - Invalid parameters 3 - test passed
Set SSP on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid parameters 3 - teardown complete Set SSP on - Invalid parameters 3 - done
Set SSP on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set SSP on - Invalid index - setup
Set SSP on - Invalid index - setup complete
Set SSP on - Invalid index - run
Sending Set Secure Simple Pairing (0x000b)
Test condition added, total 1
Set Secure Simple Pairing (0x000b): Invalid Index (0x11) Test condition complete, 0 left
Set SSP on - Invalid index - test passed
Set SSP on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set SSP on - Invalid index - teardown complete
Set SSP on - Invalid index - done
Set Secure Connections on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Success 1 - setup complete Set Secure Connections on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Secure Connections (0x002d) Test condition added, total 2
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c0 received Unregistering new settings notification Test condition complete, 0 left
Set Secure Connections on - Success 1 - test passed Set Secure Connections on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Success 1 - teardown complete Set Secure Connections on - Success 1 - done
Set Secure Connections on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Success 2 - setup complete Set Secure Connections on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Secure Connections (0x002d) Test condition added, total 3
HCI Command 0x0c7a length 1
Test condition complete, 2 left
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c1 received Unregistering new settings notification Test condition complete, 0 left
Set Secure Connections on - Success 2 - test passed Set Secure Connections on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Secure Connections on - Success 2 - teardown complete Set Secure Connections on - Success 2 - done
Set Secure Connections on - Invalid params 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid params 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid params 1 - setup complete Set Secure Connections on - Invalid params 1 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Secure Connections on - Invalid params 1 - test passed Set Secure Connections on - Invalid params 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid params 1 - teardown complete Set Secure Connections on - Invalid params 1 - done
Set Secure Connections on - Invalid params 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid params 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid params 2 - setup complete Set Secure Connections on - Invalid params 2 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Secure Connections on - Invalid params 2 - test passed Set Secure Connections on - Invalid params 2 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid params 2 - teardown complete Set Secure Connections on - Invalid params 2 - done
Set Secure Connections on - Invalid params 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid params 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid params 3 - setup complete Set Secure Connections on - Invalid params 3 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Secure Connections on - Invalid params 3 - test passed Set Secure Connections on - Invalid params 3 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid params 3 - teardown complete Set Secure Connections on - Invalid params 3 - done
Set Secure Connections on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Invalid index - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Invalid index - setup complete Set Secure Connections on - Invalid index - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Invalid Index (0x11) Test condition complete, 0 left
Set Secure Connections on - Invalid index - test passed Set Secure Connections on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Invalid index - teardown complete Set Secure Connections on - Invalid index - done
Set Secure Connections on - Not supported 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Not supported 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Not supported 1 - setup complete Set Secure Connections on - Not supported 1 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Not Supported (0x0c) Test condition complete, 0 left
Set Secure Connections on - Not supported 1 - test passed Set Secure Connections on - Not supported 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Not supported 1 - teardown complete Set Secure Connections on - Not supported 1 - done
Set Secure Connections on - Not supported 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x05
Manufacturer: 0x003f
Supported settings: 0x000110ff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections on - Not supported 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections on - Not supported 2 - setup complete Set Secure Connections on - Not supported 2 - run
Sending Set Secure Connections (0x002d)
Test condition added, total 1
Set Secure Connections (0x002d): Not Supported (0x0c) Test condition complete, 0 left
Set Secure Connections on - Not supported 2 - test passed Set Secure Connections on - Not supported 2 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections on - Not supported 2 - teardown complete Set Secure Connections on - Not supported 2 - done
Set Secure Connections Only on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections Only on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections Only on - Success 1 - setup complete Set Secure Connections Only on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Secure Connections (0x002d)
Test condition added, total 2
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c0 received
Unregistering new settings notification
Test condition complete, 0 left
Set Secure Connections Only on - Success 1 - test passed Set Secure Connections Only on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Secure Connections Only on - Success 1 - teardown complete Set Secure Connections Only on - Success 1 - done
Set Secure Connections Only on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Secure Connections Only on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Secure Connections Only on - Success 2 - setup complete Set Secure Connections Only on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Secure Connections (0x002d)
Test condition added, total 3
HCI Command 0x0c7a length 1
Test condition complete, 2 left
Set Secure Connections (0x002d): Success (0x00) Test condition complete, 1 left
New settings 0x000008c1 received
Unregistering new settings notification
Test condition complete, 0 left
Set Secure Connections Only on - Success 2 - test passed Set Secure Connections Only on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Secure Connections Only on - Success 2 - teardown complete Set Secure Connections Only on - Success 2 - done
Set High Speed on - Success - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Success - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Success - done
Set High Speed on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid parameters 1 - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid parameters 1 - done
Set High Speed on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid parameters 2 - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid parameters 2 - done
Set High Speed on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid parameters 3 - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid parameters 3 - done
Set High Speed on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Expected bit 8 not supported
Expected supported settings: 0x0001beff != 0x0001bfff
Set High Speed on - Invalid index - pre setup failed
Index Removed callback
Index: 0x0000
Set High Speed on - Invalid index - done
Set Low Energy on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Success 1 - setup
Set Low Energy on - Success 1 - setup complete
Set Low Energy on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Low Energy (0x000d)
Test condition added, total 2
Set Low Energy (0x000d): Success (0x00)
Test condition complete, 1 left
New settings 0x00000280 received
Unregistering new settings notification
Test condition complete, 0 left
Set Low Energy on - Success 1 - test passed
Set Low Energy on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Success 1 - teardown complete
Set Low Energy on - Success 1 - done
Set Low Energy on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Low Energy on - Success 2 - setup complete
Set Low Energy on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Low Energy (0x000d)
Test condition added, total 3
HCI Command 0x0c6d length 2
Test condition complete, 2 left
Set Low Energy (0x000d): Success (0x00)
Test condition complete, 1 left
New settings 0x00000281 received
Unregistering new settings notification
Test condition complete, 0 left
Set Low Energy on - Success 2 - test passed
HCI Command 0x2008 length 32
Set Low Energy on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Low Energy on - Success 2 - teardown complete
Set Low Energy on - Success 2 - done
Set Low Energy on - Success 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Success 3 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Low Energy on - Success 3 - setup complete
Set Low Energy on - Success 3 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Powered (0x0005)
Test condition added, total 3
HCI Command 0x0c6d length 2
Test condition complete, 2 left
HCI Command 0x2008 length 32
HCI Command 0x0c13 length 248
Set Powered (0x0005): Success (0x00)
Test condition complete, 1 left
New settings 0x00000281 received
Unregistering new settings notification
Test condition complete, 0 left
Set Low Energy on - Success 3 - test passed
Set Low Energy on - Success 3 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Low Energy on - Success 3 - teardown complete
Set Low Energy on - Success 3 - done
Set Low Energy on - Invalid parameters 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid parameters 1 - setup Set Low Energy on - Invalid parameters 1 - setup complete Set Low Energy on - Invalid parameters 1 - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Low Energy on - Invalid parameters 1 - test passed Set Low Energy on - Invalid parameters 1 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid parameters 1 - teardown complete Set Low Energy on - Invalid parameters 1 - done
Set Low Energy on - Invalid parameters 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid parameters 2 - setup Set Low Energy on - Invalid parameters 2 - setup complete Set Low Energy on - Invalid parameters 2 - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Low Energy on - Invalid parameters 2 - test passed Set Low Energy on - Invalid parameters 2 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid parameters 2 - teardown complete Set Low Energy on - Invalid parameters 2 - done
Set Low Energy on - Invalid parameters 3 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid parameters 3 - setup Set Low Energy on - Invalid parameters 3 - setup complete Set Low Energy on - Invalid parameters 3 - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Parameters (0x0d) Test condition complete, 0 left
Set Low Energy on - Invalid parameters 3 - test passed Set Low Energy on - Invalid parameters 3 - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid parameters 3 - teardown complete Set Low Energy on - Invalid parameters 3 - done
Set Low Energy on - Invalid index - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Low Energy on - Invalid index - setup Set Low Energy on - Invalid index - setup complete Set Low Energy on - Invalid index - run
Sending Set Low Energy (0x000d)
Test condition added, total 1
Set Low Energy (0x000d): Invalid Index (0x11) Test condition complete, 0 left
Set Low Energy on - Invalid index - test passed Set Low Energy on - Invalid index - teardown
Index Removed callback
Index: 0x0000
Set Low Energy on - Invalid index - teardown complete Set Low Energy on - Invalid index - done
Set Advertising on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Advertising on - Success 1 - setup complete
Set Advertising on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
Set Advertising (0x0029): Success (0x00)
Test condition complete, 1 left
New settings 0x00000680 received
Unregistering new settings notification
Test condition complete, 0 left
Set Advertising on - Success 1 - test passed
Set Advertising on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Success 1 - teardown complete Set Advertising on - Success 1 - done
Set Advertising on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Success 2 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Advertising on - Success 2 - setup complete
Set Advertising on - Success 2 - run
Registering new settings notification
Test condition added, total 1
Registering HCI command callback
Test condition added, total 2
Sending Set Advertising (0x0029)
Test condition added, total 3
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Test condition complete, 2 left
Set Advertising (0x0029): Success (0x00)
Test condition complete, 1 left
New settings 0x00000681 received
Unregistering new settings notification
Test condition complete, 0 left
Set Advertising on - Success 2 - test passed
Set Advertising on - Success 2 - teardown
New settings event received
Index Removed callback
Index: 0x0000
Set Advertising on - Success 2 - teardown complete Set Advertising on - Success 2 - done
Set Advertising on - Rejected 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Rejected 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set Advertising on - Rejected 1 - setup complete
Set Advertising on - Rejected 1 - run
Sending Set Advertising (0x0029)
Test condition added, total 1
Set Advertising (0x0029): Rejected (0x0b)
Test condition complete, 0 left
Set Advertising on - Rejected 1 - test passed
Set Advertising on - Rejected 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Rejected 1 - teardown complete Set Advertising on - Rejected 1 - done
Set Advertising on - Appearance 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Appearance 1 - setup
Initial settings completed
Setup sending Set Appearance (0x0043) Test setup condition added, total 1
Test setup condition complete, 0 left
Set Advertising on - Appearance 1 - setup complete Set Advertising on - Appearance 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
HCI Command 0x2009 length 32
Test condition complete, 1 left
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Set Advertising (0x0029): Success (0x00) Test condition complete, 0 left
Set Advertising on - Appearance 1 - test passed Set Advertising on - Appearance 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Appearance 1 - teardown complete Set Advertising on - Appearance 1 - done
Set Advertising on - Local name 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Local name 1 - setup
Initial settings completed
Setup sending Set Local Name (0x000f) Test setup condition added, total 1
Test setup condition complete, 0 left
Set Advertising on - Local name 1 - setup complete Set Advertising on - Local name 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
HCI Command 0x2009 length 32
Test condition complete, 1 left
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Set Advertising (0x0029): Success (0x00) Test condition complete, 0 left
Set Advertising on - Local name 1 - test passed Set Advertising on - Local name 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Local name 1 - teardown complete Set Advertising on - Local name 1 - done
Set Advertising on - Name + Appear 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set Advertising on - Name + Appear 1 - setup
Initial settings completed
Sending setup opcode array
Setup sending Set Appearance (0x0043)
Test setup condition added, total 1
Setup sending Set Local Name (0x000f)
Test setup condition added, total 2
Test setup condition complete, 1 left
Test setup condition complete, 0 left
Set Advertising on - Name + Appear 1 - setup complete Set Advertising on - Name + Appear 1 - run
Registering HCI command callback
Test condition added, total 1
Sending Set Advertising (0x0029)
Test condition added, total 2
HCI Command 0x2009 length 32
Test condition complete, 1 left
HCI Command 0x2005 length 6
HCI Command 0x2006 length 15
HCI Command 0x200a length 1
Set Advertising (0x0029): Success (0x00) Test condition complete, 0 left
Set Advertising on - Name + Appear 1 - test passed Set Advertising on - Name + Appear 1 - teardown
Index Removed callback
Index: 0x0000
Set Advertising on - Name + Appear 1 - teardown complete Set Advertising on - Name + Appear 1 - done
Set BR/EDR off - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set BR/EDR off - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set BR/EDR off - Success 1 - setup complete
Set BR/EDR off - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set BR/EDR (0x002a)
Test condition added, total 2
Set BR/EDR (0x002a): Success (0x00)
Test condition complete, 1 left
New settings 0x00000200 received
Unregistering new settings notification
Test condition complete, 0 left
Set BR/EDR off - Success 1 - test passed
Set BR/EDR off - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set BR/EDR off - Success 1 - teardown complete
Set BR/EDR off - Success 1 - done
Set BR/EDR on - Success 1 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: Set BR/EDR on - Success 1 - setup
Initial settings completed
Client set connectable: Success (0x00)
Set BR/EDR on - Success 1 - setup complete
Set BR/EDR on - Success 1 - run
Registering new settings notification
Test condition added, total 1
Sending Set BR/EDR (0x002a)
Test condition added, total 2
Set BR/EDR (0x002a): Success (0x00)
Test condition complete, 1 left
New settings 0x00000280 received
Unregistering new settings notification
Test condition complete, 0 left
Set BR/EDR on - Success 1 - test passed
Set BR/EDR on - Success 1 - teardown
Index Removed callback
Index: 0x0000
Set BR/EDR on - Success 1 - teardown complete
Set BR/EDR on - Success 1 - done
Set BR/EDR on - Success 2 - init
Read Version callback
Status: Success (0x00)
Version 1.20
Read Commands callback
Status: Success (0x00)
Read Index List callback
Status: Success (0x00)
Index Added callback
Index: 0x0000
Read Info callback
Status: Success (0x00)
Address: 00:AA:01:00:00:00
Version: 0x09
Manufacturer: 0x003f
Supported settings: 0x0001beff
Current settings: 0x00000080
Class: 0x000000
Name:
Short name: 13,126 lines not shown · raw message
Part of this message is not shown here. View the raw message.
Marcel Holtmann
maintainerHi Hans,
Quoted 105 lines
The
hci_suspend_notifierwhich was introduced last year, is causing problems for uart attached btrtl devices. These devices may loose their firmware and their baudrate setting over a suspend/resume.Since we don't even know the baudrate after a suspend/resume recovering from this is tricky. The driver solves this by treating these devices the same as USB BT HCIs which drop of the bus during suspend.
Specifically the driver:
1. Simply unconditionally turns the device fully off during system-suspend to save maximum power.
2. Callsdevice_reprobe()from a workqueue to fully re-init the device from scratch on system-resume (unregistering the old HCI and registering a new HCI).This means that these devices do not benefit from the suspend / resume handling work done by the
hci_suspend_notifier. At best this unnecessarily adds some time to the suspend/resume time.But in practice this is actually causing problems:
1. These btrtl devices seem to not like the
HCI_OP_WRITE_SCAN_ENABLE( SCAN_DISABLED)request being send to them when entering theBT_SUSPEND_CONFIGURE_WAKEstate. The same request send onBT_SUSPEND_DISCONNECTworks fine, but the second one send (unnecessarily?) from theBT_SUSPEND_CONFIGURE_WAKEtransition causes the device to hang:[ 573.497754] PM: suspend entry (s2idle) [ 573.554615] Filesystems sync: 0.056 seconds [ 575.837753] Bluetooth: hci0: Timed out waiting for suspend events [ 575.837801] Bluetooth: hci0: Suspend timeout bit: 4 [ 575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -1102. The
PM_POST_SUSPEND/BT_RUNNINGtransition races with the driver-unbinding done by thedevice_reprobe()work.
If thehci_suspend_notifierwins the race it is talking to a dead device leading to the following errors being logged:[ 598.686060] Bluetooth: hci0: Timed out waiting for suspend events [ 598.686124] Bluetooth: hci0: Suspend timeout bit: 5 [ 598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110In both cases things still work, but the suspend-notifier is causing these ugly errors getting logged and ut increase both the suspend- and the resume-time by 2 seconds.
This commit avoids these problems by disabling the
hci_suspend_notifier.Cc Luiz Augusto von Dentz <[email protected]>Cc Vasily Khoruzhick <[email protected]>Cc Abhishek Pandit-Subedi <[email protected]>Signed-off-by Hans de Goede <[email protected]>---
Changes in v2:
- Use the newHCI_QUIRK_NO_SUSPEND_NOTIFIERquirk, instead of directly unregistering the notifier fromhci_h5.c
---drivers/bluetooth/hci_h5.c | 7 +++++++ drivers/bluetooth/hci_serdev.c | 3 +++ drivers/bluetooth/hci_uart.h | 13 +++++++------ 3 files changed, 17 insertions(+), 6 deletions(-)drivers/bluetooth/hci_h5.c +7
-0@@ -919,6 +919,13 @@ static int h5_btrtl_setup(struct h5 *h5)static void h5_btrtl_open (struct h5 *h5) { +/* +* Since h5_btrtl_resume() does a device_reprobe() the suspend handling +* done by the hci_suspend_notifier is not necessary; it actually causes +* delays and a bunch of errors to get logged, so disable it. +*/ +set_bit (HCI_UART_NO_SUSPEND_NOTIFIER , &h5->hu->hdev_flags); +/* Devices always start with these fixed parameters */ serdev_device_set_flow_control (h5->hu->serdev, false);serdev_device_set_parity (h5->hu->serdev,SERDEV_PARITY_EVEN );drivers/bluetooth/hci_serdev.c +3
-0@@ -349,6 +349,9 @@ int hci_uart_register_device(struct hci_uart *hu,if (test_bit (HCI_UART_EXT_CONFIG , &hu->hdev_flags))set_bit (HCI_QUIRK_EXTERNAL_CONFIG , &hdev->quirks); +if (test_bit (HCI_UART_NO_SUSPEND_NOTIFIER , &hu->hdev_flags)) +set_bit (HCI_QUIRK_NO_SUSPEND_NOTIFIER , &hdev->quirks); +if (test_bit (HCI_UART_CREATE_AMP , &hu->hdev_flags)) hdev->dev_type =HCI_AMP ;else drivers/bluetooth/hci_uart.h +0
-3@@ -35,12 +35,13 @@#define HCI_UART_NOKIA 10#define HCI_UART_MRVL 11 -#define HCI_UART_RAW_DEVICE 0 -#define HCI_UART_RESET_ON_INIT 1 -#define HCI_UART_CREATE_AMP 2
drivers/bluetooth/hci_uart.h line 44
Quoted 10 lines
drivers/bluetooth/hci_uart.h +7
-3-#define HCI_UART_INIT_PENDING 3 -#define HCI_UART_EXT_CONFIG 4 -#define HCI_UART_VND_DETECT 5 +#define HCI_UART_RAW_DEVICE 0 +#define HCI_UART_RESET_ON_INIT 1 +#define HCI_UART_CREATE_AMP 2 +#define HCI_UART_INIT_PENDING 3 +#define HCI_UART_EXT_CONFIG 4 +#define HCI_UART_VND_DETECT 5 +#define HCI_UART_NO_SUSPEND_NOTIFIER 6
not really happy using these values here. They are for the ioctl API. Any chance you can just use hu->flags for this?
Regards
Marcel
Hi Marcel,
Quoted 104 lines · Marcel Holtmann
Hi Hans,
Quoted 102 lines
The
hci_suspend_notifierwhich was introduced last year, is causing problems for uart attached btrtl devices. These devices may loose their firmware and their baudrate setting over a suspend/resume.Since we don't even know the baudrate after a suspend/resume recovering from this is tricky. The driver solves this by treating these devices the same as USB BT HCIs which drop of the bus during suspend.
Specifically the driver:
1. Simply unconditionally turns the device fully off during system-suspend to save maximum power.
2. Callsdevice_reprobe()from a workqueue to fully re-init the device from scratch on system-resume (unregistering the old HCI and registering a new HCI).This means that these devices do not benefit from the suspend / resume handling work done by the
hci_suspend_notifier. At best this unnecessarily adds some time to the suspend/resume time.But in practice this is actually causing problems:
1. These btrtl devices seem to not like the
HCI_OP_WRITE_SCAN_ENABLE( SCAN_DISABLED)request being send to them when entering theBT_SUSPEND_CONFIGURE_WAKEstate. The same request send onBT_SUSPEND_DISCONNECTworks fine, but the second one send (unnecessarily?) from theBT_SUSPEND_CONFIGURE_WAKEtransition causes the device to hang:[ 573.497754] PM: suspend entry (s2idle) [ 573.554615] Filesystems sync: 0.056 seconds [ 575.837753] Bluetooth: hci0: Timed out waiting for suspend events [ 575.837801] Bluetooth: hci0: Suspend timeout bit: 4 [ 575.837925] Bluetooth: hci0: Suspend notifier action (3) failed: -1102. The
PM_POST_SUSPEND/BT_RUNNINGtransition races with the driver-unbinding done by thedevice_reprobe()work.
If thehci_suspend_notifierwins the race it is talking to a dead device leading to the following errors being logged:[ 598.686060] Bluetooth: hci0: Timed out waiting for suspend events [ 598.686124] Bluetooth: hci0: Suspend timeout bit: 5 [ 598.686237] Bluetooth: hci0: Suspend notifier action (4) failed: -110In both cases things still work, but the suspend-notifier is causing these ugly errors getting logged and ut increase both the suspend- and the resume-time by 2 seconds.
This commit avoids these problems by disabling the
hci_suspend_notifier.Cc Luiz Augusto von Dentz <[email protected]>Cc Vasily Khoruzhick <[email protected]>Cc Abhishek Pandit-Subedi <[email protected]>Signed-off-by Hans de Goede <[email protected]>---
Changes in v2:
- Use the newHCI_QUIRK_NO_SUSPEND_NOTIFIERquirk, instead of directly unregistering the notifier fromhci_h5.c
---drivers/bluetooth/hci_h5.c | 7 +++++++ drivers/bluetooth/hci_serdev.c | 3 +++ drivers/bluetooth/hci_uart.h | 13 +++++++------ 3 files changed, 17 insertions(+), 6 deletions(-)drivers/bluetooth/hci_h5.c +7
-0@@ -919,6 +919,13 @@ static int h5_btrtl_setup(struct h5 *h5)static void h5_btrtl_open (struct h5 *h5) { +/* +* Since h5_btrtl_resume() does a device_reprobe() the suspend handling +* done by the hci_suspend_notifier is not necessary; it actually causes +* delays and a bunch of errors to get logged, so disable it. +*/ +set_bit (HCI_UART_NO_SUSPEND_NOTIFIER , &h5->hu->hdev_flags); +/* Devices always start with these fixed parameters */ serdev_device_set_flow_control (h5->hu->serdev, false);serdev_device_set_parity (h5->hu->serdev,SERDEV_PARITY_EVEN );drivers/bluetooth/hci_serdev.c +3
-0@@ -349,6 +349,9 @@ int hci_uart_register_device(struct hci_uart *hu,if (test_bit (HCI_UART_EXT_CONFIG , &hu->hdev_flags))set_bit (HCI_QUIRK_EXTERNAL_CONFIG , &hdev->quirks); +if (test_bit (HCI_UART_NO_SUSPEND_NOTIFIER , &hu->hdev_flags)) +set_bit (HCI_QUIRK_NO_SUSPEND_NOTIFIER , &hdev->quirks); +if (test_bit (HCI_UART_CREATE_AMP , &hu->hdev_flags)) hdev->dev_type =HCI_AMP ;else drivers/bluetooth/hci_uart.h +0
-0@@ -35,12 +35,13 @@#define HCI_UART_NOKIA 10#define HCI_UART_MRVL 11
Quoted 15 lines
drivers/bluetooth/hci_uart.h line 44
Quoted 13 lines
drivers/bluetooth/hci_uart.h +7
-6-#define HCI_UART_RAW_DEVICE 0 -#define HCI_UART_RESET_ON_INIT 1 -#define HCI_UART_CREATE_AMP 2 -#define HCI_UART_INIT_PENDING 3 -#define HCI_UART_EXT_CONFIG 4 -#define HCI_UART_VND_DETECT 5 +#define HCI_UART_RAW_DEVICE 0 +#define HCI_UART_RESET_ON_INIT 1 +#define HCI_UART_CREATE_AMP 2 +#define HCI_UART_INIT_PENDING 3 +#define HCI_UART_EXT_CONFIG 4 +#define HCI_UART_VND_DETECT 5 +#define HCI_UART_NO_SUSPEND_NOTIFIER 6not really happy using these values here. They are for the ioctl API. Any chance you can just use
hu->flagsfor this?
I see no reason why that would not work. I'll prepare (and test) a v2 with this change.
Regards,
Hans