dt-bindings:iio:dac:ad5755: txt to yaml format conversion.

deleted file mode 100644
index 502e1e55adbd..000000000000
@@ -1,124 +0,0 @@
-* Analog Devices AD5755 IIO Multi-Channel DAC Linux Driver
-
-Required properties:
- - compatible: Has to contain one of the following:
-	adi,ad5755
-	adi,ad5755-1
-	adi,ad5757
-	adi,ad5735
-	adi,ad5737
-
- - reg: spi chip select number for the device
- - spi-cpha or spi-cpol: is the only modes that is supported
-
-Recommended properties:
- - spi-max-frequency: Definition as per
-		Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Optional properties:
-See include/dt-bindings/iio/ad5755.h
- - adi,ext-dc-dc-compenstation-resistor: boolean set if the hardware have an
-					 external resistor and thereby bypasses
-					 the internal compensation resistor.
- - adi,dc-dc-phase:
-	Valid values for DC DC Phase control is:
-	0: All dc-to-dc converters clock on the same edge.
-	1: Channel A and Channel B clock on the same edge,
-	   Channel C and Channel D clock on opposite edges.
-	2: Channel A and Channel C clock on the same edge,
-	   Channel B and Channel D clock on opposite edges.
-	3: Channel A, Channel B, Channel C, and Channel D
-	   clock 90 degrees out of phase from each other.
- - adi,dc-dc-freq-hz:
-	Valid values for DC DC frequency is [Hz]:
-	250000
-	410000
-	650000
- - adi,dc-dc-max-microvolt:
-	Valid values for the maximum allowed Vboost voltage supplied by
-	the dc-to-dc converter is:
-	23000000
-	24500000
-	27000000
-	29500000
-
-Optional for every channel:
- - adi,mode:
-	Valid values for DAC modes is:
-	0: 0 V to 5 V voltage range.
-	1: 0 V to 10 V voltage range.
-	2: Plus minus 5 V voltage range.
-	3: Plus minus 10 V voltage range.
-	4: 4 mA to 20 mA current range.
-	5: 0 mA to 20 mA current range.
-	6: 0 mA to 24 mA current range.
- - adi,ext-current-sense-resistor: boolean set if the hardware a external
-				   current sense resistor.
- - adi,enable-voltage-overrange: boolean enable voltage overrange
- - adi,slew: Array of slewrate settings should contain 3 fields:
-	1: Should be either 0 or 1 in order to enable or disable slewrate.
-	2: Slew rate settings:
-		Valid values for the slew rate update frequency:
-		64000
-		32000
-		16000
-		8000
-		4000
-		2000
-		1000
-		500
-		250
-		125
-		64
-		32
-		16
-		8
-		4
-		0
-	3: Slew step size:
-		Valid values for the step size LSBs:
-		1
-		2
-		4
-		16
-		32
-		64
-		128
-		256
-
-Example:
-dac@0 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	compatible = "adi,ad5755";
-	reg = <0>;
-	spi-max-frequency = <1000000>;
-	spi-cpha;
-	adi,dc-dc-phase = <0>;
-	adi,dc-dc-freq-hz = <410000>;
-	adi,dc-dc-max-microvolt = <23000000>;
-	channel@0 {
-		reg = <0>;
-		adi,mode = <4>;
-		adi,ext-current-sense-resistor;
-		adi,slew = <0 64000 1>;
-	};
-	channel@1 {
-		reg = <1>;
-		adi,mode = <4>;
-		adi,ext-current-sense-resistor;
-		adi,slew = <0 64000 1>;
-	};
-	channel@2 {
-		reg = <2>;
-		adi,mode = <4>;
-		adi,ext-current-sense-resistor;
-		adi,slew = <0 64000 1>;
-	};
-	channel@3 {
-		reg = <3>;
-		adi,mode = <4>;
-		adi,ext-current-sense-resistor;
-		adi,slew = <0 64000 1>;
-	};
-};

169 lines not on this page · raw message