Skip to contentSkip to conversation

iio: accel: bmc150: Add support for yoga's with dual accelerometers with an ACPI HID of DUAL250E

PATCH In review Hans de Goede 3 participants 15 messages May 23, 2021 – Jun 9, 2021 IIO

lore
Share & tools
lore
#0 lore raw

v2 cover iio: accel: bmc150: Add support for yoga's with dual accelerometers with an ACPI HID of DUAL250E

Hi all,

Here is v2 of this series, addressing Andy's review remarks and rewrap some comments at 80 chars limit.

For more info here is the v1 cover-letter:

Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels to allow the OS to determine the angle between the display and the base of the device, so that the OS can determine if the 2-in-1 is in laptop or in tablet-mode.

We already support this setup on devices using a single ACPI node with a HID of "BOSC0200" to describe both accelerometers. This patch set extends this support to also support the same setup but then using a HID of "DUAL250E".

While testing this I found some crashes on rmmod, patches 1-2 fix those patches, patch 3 does some refactoring and patch 4 adds support for the "DUAL250E" HID.

Unfortunately we need some more special handling though, which the rest of the patches are for.

On Windows both accelerometers are read (polled) by a special service and this service calls a DSM (Device Specific Method), which in turn translates the angles to one of laptop/tablet/tent/stand mode and then notifies the EC about the new mode and the EC then enables or disables the builtin keyboard and touchpad based in the mode.

When the 2-in-1 is powered-on or resumed folded in tablet mode the EC senses this independent of the DSM by using a HALL effect sensor which senses that the keyboard has been folded away behind the display.

At power-on or resume the EC disables the keyboard based on this and the only way to get the keyboard to work after this is to call the DSM to re-enable it (similar to how we also need to call a special DSM in the kxcjk-1013.c accel driver to re-enable the keyboard).

Patches 5-7 deal with the DSM mess and patch 8 adds labels to the 2 accelerometers specifying which one is which.

Regards,

Hans

Hans de Goede (9):
iio: accel: bmc150: Fix dereferencing the wrong pointer in
bmc150_get/set_second_device
iio: accel: bmc150: Don't make the remove function of the second
accelerometer unregister itself
iio: accel: bmc150: Move check for second ACPI device into a separate
function
iio: accel: bmc150: Add support for dual-accelerometers with a
DUAL250E HID
iio: accel: bmc150: Move struct bmc150_accel_data definition to

    bmc150-accel.h

iio: accel: bmc150: Remove bmc150_set/get_second_device() accessor
functions
iio: accel: bmc150: Add support for DUAL250E ACPI DSM for setting the
hinge angle
iio: accel: bmc150: Refactor bmc150_apply_acpi_orientation()
iio: accel: bmc150: Set label based on accel-location for ACPI
DUAL250E fwnodes

 drivers/iio/accel/bmc150-accel-core.c | 110 +++++----------
 drivers/iio/accel/bmc150-accel-i2c.c  | 193 ++++++++++++++++++++++----
 drivers/iio/accel/bmc150-accel.h      |  66 ++++++++-
 3 files changed, 260 insertions(+), 109 deletions(-)
Signature · 1 line
2.31.1
#1 lore raw

PATCH v2 1/9 iio: accel: bmc150: Fix dereferencing the wrong pointer in bmc150_get/set_second_device

The drvdata for iio-parent devices points to the struct iio_dev for the iio-device. So by directly casting the return from i2c_get_clientdata() to struct bmc150_accel_data * the code was ending up storing the second_dev pointer in (and retrieving it from) some semi-random offset inside struct iio_dev, rather then storing it in the second_dev member of the bmc150_accel_data struct.

Fix the code to get the struct bmc150_accel_data * pointer to call iio_priv() on the struct iio_dev * returned by i2c_get_clientdata(), so that the correct pointer gets dereferenced.

This fixes the following oops on rmmod, caused by trying to dereference the wrong return of bmc150_get_second_device():

[  238.980737] BUG: unable to handle page fault for address: 0000000000004710
[  238.980755] #PF: supervisor read access in kernel mode
[  238.980760] #PF: error_code(0x0000) - not-present page
...
[  238.980841]  i2c_unregister_device.part.0+0x19/0x60
[  238.980856]  0xffffffffc0815016
[  238.980863]  i2c_device_remove+0x25/0xb0
[  238.980869]  __device_release_driver+0x180/0x240
[  238.980876]  driver_detach+0xd4/0x120
[  238.980882]  bus_remove_driver+0x5b/0xd0
[  238.980888]  i2c_del_driver+0x44/0x70

While at it also remove the now no longer sensible checks for data being NULL, iio_priv never returns NULL for an iio_dev with non 0 sized private-data.

Fixes 5bfb3a4bd8f6 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc Jeremy Cline <[email protected]>
---
 drivers/iio/accel/bmc150-accel-core.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +3 -7
index 04d85ce34e9f..3a3f67930165 100644
@@ -1809,10 +1809,7 @@ EXPORT_SYMBOL_GPL(bmc150_accel_core_probe);
 
 struct i2c_client *bmc150_get_second_device(struct i2c_client *client)
 {
-	struct bmc150_accel_data *data = i2c_get_clientdata(client);
-
-	if (!data)
-		return NULL;
+	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
 	return data->second_device;
 }
@@ -1820,10 +1817,9 @@ EXPORT_SYMBOL_GPL(bmc150_get_second_device);
 
 void bmc150_set_second_device(struct i2c_client *client)
 {
-	struct bmc150_accel_data *data = i2c_get_clientdata(client);
+	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
-	if (data)
-		data->second_device = client;
+	data->second_device = client;
 }
 EXPORT_SYMBOL_GPL(bmc150_set_second_device);
 
Signature · 1 line
2.31.1
#2 lore raw

PATCH v2 2/9 iio: accel: bmc150: Don't make the remove function of the second accelerometer unregister itself

In reply to Hans de Goede

On machines with dual accelerometers described in a single ACPI fwnode, the bmc150_accel_probe() instantiates a second i2c-client for the second accelerometer.

A pointer to this manually instantiated second i2c-client is stored inside the iio_dev's private-data through bmc150_set_second_device(), so that the i2c-client can be unregistered from bmc150_accel_remove().

Before this commit bmc150_set_second_device() took only 1 argument so it would store the pointer in private-data of the iio_dev belonging to the manually instantiated i2c-client, leading to the bmc150_accel_remove() call for the second_dev trying to unregister *itself* while it was being removed, leading to a deadlock and rmmod hanging.

Change bmc150_set_second_device() to take 2 arguments: 1. The i2c-client which is instantiating the second i2c-client for the 2nd accelerometer and
2. The second-device pointer itself (which also is an i2c-client).

This will store the second_device pointer in the private data of the iio_dev belonging to the (ACPI instantiated) i2c-client for the first accelerometer and will make bmc150_accel_remove() unregister the second_device i2c-client when called for the first client, avoiding the deadlock.

Fixes 5bfb3a4bd8f6 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc Jeremy Cline <[email protected]>
---
 drivers/iio/accel/bmc150-accel-core.c | 4 ++--
 drivers/iio/accel/bmc150-accel-i2c.c  | 2 +-
 drivers/iio/accel/bmc150-accel.h      | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +2 -2
index 3a3f67930165..8ff358c37a81 100644
@@ -1815,11 +1815,11 @@ struct i2c_client *bmc150_get_second_device(struct i2c_client *client)
 }
 EXPORT_SYMBOL_GPL(bmc150_get_second_device);
 
-void bmc150_set_second_device(struct i2c_client *client)
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev)
 {
 	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
-	data->second_device = client;
+	data->second_device = second_dev;
 }
 EXPORT_SYMBOL_GPL(bmc150_set_second_device);
 
drivers/iio/accel/bmc150-accel-i2c.c +1 -1
index 69f709319484..2afaae0294ee 100644
@@ -70,7 +70,7 @@ static int bmc150_accel_probe(struct i2c_client *client,
 
 		second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
 		if (!IS_ERR(second_dev))
-			bmc150_set_second_device(second_dev);
+			bmc150_set_second_device(client, second_dev);
 	}
 #endif
 
drivers/iio/accel/bmc150-accel.h +1 -1
index 6024f15b9700..e30c1698f6fb 100644
@@ -18,7 +18,7 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 			    const char *name, bool block_supported);
 int bmc150_accel_core_remove(struct device *dev);
 struct i2c_client *bmc150_get_second_device(struct i2c_client *second_device);
-void bmc150_set_second_device(struct i2c_client *second_device);
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev);
 extern const struct dev_pm_ops bmc150_accel_pm_ops;
 extern const struct regmap_config bmc150_regmap_conf;
 
Signature · 1 line
2.31.1
maintainer
#3 lore raw

Re: [PATCH v2 2/9] iio: accel: bmc150: Don't make the remove function of the second accelerometer unregister itself

Quoted 24 lines · On Sun, 23 May 2021 19:00:56 +0200 Hans de Goede <[email protected]> wrote:

On machines with dual accelerometers described in a single ACPI fwnode, the bmc150_accel_probe() instantiates a second i2c-client for the second accelerometer.

A pointer to this manually instantiated second i2c-client is stored inside the iio_dev's private-data through bmc150_set_second_device(), so that the i2c-client can be unregistered from bmc150_accel_remove().

Before this commit bmc150_set_second_device() took only 1 argument so it would store the pointer in private-data of the iio_dev belonging to the manually instantiated i2c-client, leading to the bmc150_accel_remove() call for the second_dev trying to unregister *itself* while it was being removed, leading to a deadlock and rmmod hanging.

Change bmc150_set_second_device() to take 2 arguments: 1. The i2c-client which is instantiating the second i2c-client for the 2nd accelerometer and
2. The second-device pointer itself (which also is an i2c-client).

This will store the second_device pointer in the private data of the iio_dev belonging to the (ACPI instantiated) i2c-client for the first accelerometer and will make bmc150_accel_remove() unregister the second_device i2c-client when called for the first client, avoiding the deadlock.

Quoted 3 lines
Fixes 5bfb3a4bd8f6 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc Jeremy Cline <[email protected]>

Patches 1 and 2 applied to the fixes-togreg branch of iio.git and marked for stable. The rest will have to wait for now.

Thanks,

Jonathan

Quoted 50 lines
---
 drivers/iio/accel/bmc150-accel-core.c | 4 ++--
 drivers/iio/accel/bmc150-accel-i2c.c  | 2 +-
 drivers/iio/accel/bmc150-accel.h      | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +2 -2
index 3a3f67930165..8ff358c37a81 100644
@@ -1815,11 +1815,11 @@ struct i2c_client *bmc150_get_second_device(struct i2c_client *client)
 }
 EXPORT_SYMBOL_GPL(bmc150_get_second_device);
 
-void bmc150_set_second_device(struct i2c_client *client)
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev)
 {
 	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
-	data->second_device = client;
+	data->second_device = second_dev;
 }
 EXPORT_SYMBOL_GPL(bmc150_set_second_device);
 
drivers/iio/accel/bmc150-accel-i2c.c +1 -1
index 69f709319484..2afaae0294ee 100644
@@ -70,7 +70,7 @@ static int bmc150_accel_probe(struct i2c_client *client,
 
 		second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
 		if (!IS_ERR(second_dev))
-			bmc150_set_second_device(second_dev);
+			bmc150_set_second_device(client, second_dev);
 	}
 #endif
 
drivers/iio/accel/bmc150-accel.h +1 -1
index 6024f15b9700..e30c1698f6fb 100644
@@ -18,7 +18,7 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 			    const char *name, bool block_supported);
 int bmc150_accel_core_remove(struct device *dev);
 struct i2c_client *bmc150_get_second_device(struct i2c_client *second_device);
-void bmc150_set_second_device(struct i2c_client *second_device);
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev);
 extern const struct dev_pm_ops bmc150_accel_pm_ops;
 extern const struct regmap_config bmc150_regmap_conf;
 
maintainer
#4 lore raw

Re: [PATCH v2 2/9] iio: accel: bmc150: Don't make the remove function of the second accelerometer unregister itself

Quoted 27 lines · On Wed, 26 May 2021 17:55:41 +0100 Jonathan Cameron <[email protected]> wrote:
Quoted 24 lines · On Sun, 23 May 2021 19:00:56 +0200 Hans de Goede <[email protected]> wrote:

On machines with dual accelerometers described in a single ACPI fwnode, the bmc150_accel_probe() instantiates a second i2c-client for the second accelerometer.

A pointer to this manually instantiated second i2c-client is stored inside the iio_dev's private-data through bmc150_set_second_device(), so that the i2c-client can be unregistered from bmc150_accel_remove().

Before this commit bmc150_set_second_device() took only 1 argument so it would store the pointer in private-data of the iio_dev belonging to the manually instantiated i2c-client, leading to the bmc150_accel_remove() call for the second_dev trying to unregister *itself* while it was being removed, leading to a deadlock and rmmod hanging.

Change bmc150_set_second_device() to take 2 arguments: 1. The i2c-client which is instantiating the second i2c-client for the 2nd accelerometer and
2. The second-device pointer itself (which also is an i2c-client).

This will store the second_device pointer in the private data of the iio_dev belonging to the (ACPI instantiated) i2c-client for the first accelerometer and will make bmc150_accel_remove() unregister the second_device i2c-client when called for the first client, avoiding the deadlock.

Quoted 5 lines
Quoted 3 lines
Fixes 5bfb3a4bd8f6 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc Jeremy Cline <[email protected]>

Patches 1 and 2 applied to the fixes-togreg branch of iio.git and marked for stable. The rest will have to wait for now.

Cycle has gone past rather quicker than expected, so I've changed my mind on these two and pulled them across to the togreg branch targeting 5.14. That will mean the hit stable a little later (after 5.14-rc1) but pretty much ensures the rest of the series makes it into 5.14

Thanks,

Jonathan

Quoted 56 lines

Thanks,

Jonathan

Quoted 50 lines
---
 drivers/iio/accel/bmc150-accel-core.c | 4 ++--
 drivers/iio/accel/bmc150-accel-i2c.c  | 2 +-
 drivers/iio/accel/bmc150-accel.h      | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +2 -2
index 3a3f67930165..8ff358c37a81 100644
@@ -1815,11 +1815,11 @@ struct i2c_client *bmc150_get_second_device(struct i2c_client *client)
 }
 EXPORT_SYMBOL_GPL(bmc150_get_second_device);
 
-void bmc150_set_second_device(struct i2c_client *client)
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev)
 {
 	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
-	data->second_device = client;
+	data->second_device = second_dev;
 }
 EXPORT_SYMBOL_GPL(bmc150_set_second_device);
 
drivers/iio/accel/bmc150-accel-i2c.c +1 -1
index 69f709319484..2afaae0294ee 100644
@@ -70,7 +70,7 @@ static int bmc150_accel_probe(struct i2c_client *client,
 
 		second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
 		if (!IS_ERR(second_dev))
-			bmc150_set_second_device(second_dev);
+			bmc150_set_second_device(client, second_dev);
 	}
 #endif
 
drivers/iio/accel/bmc150-accel.h +1 -1
index 6024f15b9700..e30c1698f6fb 100644
@@ -18,7 +18,7 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 			    const char *name, bool block_supported);
 int bmc150_accel_core_remove(struct device *dev);
 struct i2c_client *bmc150_get_second_device(struct i2c_client *second_device);
-void bmc150_set_second_device(struct i2c_client *second_device);
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev);
 extern const struct dev_pm_ops bmc150_accel_pm_ops;
 extern const struct regmap_config bmc150_regmap_conf;
 
#5 lore raw

Re: [PATCH v2 2/9] iio: accel: bmc150: Don't make the remove function of the second accelerometer unregister itself

Hi,

Quoted 33 lines · Jonathan Cameron
Quoted 30 lines · On Wed, 26 May 2021 17:55:41 +0100 Jonathan Cameron <[email protected]> wrote:
Quoted 27 lines · On Sun, 23 May 2021 19:00:56 +0200 Hans de Goede <[email protected]> wrote:

On machines with dual accelerometers described in a single ACPI fwnode, the bmc150_accel_probe() instantiates a second i2c-client for the second accelerometer.

A pointer to this manually instantiated second i2c-client is stored inside the iio_dev's private-data through bmc150_set_second_device(), so that the i2c-client can be unregistered from bmc150_accel_remove().

Before this commit bmc150_set_second_device() took only 1 argument so it would store the pointer in private-data of the iio_dev belonging to the manually instantiated i2c-client, leading to the bmc150_accel_remove() call for the second_dev trying to unregister *itself* while it was being removed, leading to a deadlock and rmmod hanging.

Change bmc150_set_second_device() to take 2 arguments: 1. The i2c-client which is instantiating the second i2c-client for the 2nd accelerometer and
2. The second-device pointer itself (which also is an i2c-client).

This will store the second_device pointer in the private data of the iio_dev belonging to the (ACPI instantiated) i2c-client for the first accelerometer and will make bmc150_accel_remove() unregister the second_device i2c-client when called for the first client, avoiding the deadlock.

Fixes 5bfb3a4bd8f6 ("iio: accel: bmc150: Check for a second ACPI device for BOSC0200")
Cc Jeremy Cline <[email protected]>
Quoted 6 lines
Quoted 2 lines

Patches 1 and 2 applied to the fixes-togreg branch of iio.git and marked for stable. The rest will have to wait for now.

Cycle has gone past rather quicker than expected, so I've changed my mind on these two and pulled them across to the togreg branch targeting 5.14.
That will mean the hit stable a little later (after 5.14-rc1)

Ok, note the problems fixed in the first 2 patches are only hit on a rmmod (or an unbind), so there is no big hurry in getting them in to the stable series.

Quoted 1 line

but pretty much ensures the rest of the series makes it into 5.14

Getting the rest of the series into 5.14 without issues is much appreciated, thank you.

Regards,

Hans

Quoted 52 lines
Quoted 51 lines
Quoted 50 lines
---
 drivers/iio/accel/bmc150-accel-core.c | 4 ++--
 drivers/iio/accel/bmc150-accel-i2c.c  | 2 +-
 drivers/iio/accel/bmc150-accel.h      | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +2 -2
index 3a3f67930165..8ff358c37a81 100644
@@ -1815,11 +1815,11 @@ struct i2c_client *bmc150_get_second_device(struct i2c_client *client)
 }
 EXPORT_SYMBOL_GPL(bmc150_get_second_device);
 
-void bmc150_set_second_device(struct i2c_client *client)
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev)
 {
 	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
-	data->second_device = client;
+	data->second_device = second_dev;
 }
 EXPORT_SYMBOL_GPL(bmc150_set_second_device);
 
drivers/iio/accel/bmc150-accel-i2c.c +1 -1
index 69f709319484..2afaae0294ee 100644
@@ -70,7 +70,7 @@ static int bmc150_accel_probe(struct i2c_client *client,
 
 		second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
 		if (!IS_ERR(second_dev))
-			bmc150_set_second_device(second_dev);
+			bmc150_set_second_device(client, second_dev);
 	}
 #endif
 
drivers/iio/accel/bmc150-accel.h +1 -1
index 6024f15b9700..e30c1698f6fb 100644
@@ -18,7 +18,7 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 			    const char *name, bool block_supported);
 int bmc150_accel_core_remove(struct device *dev);
 struct i2c_client *bmc150_get_second_device(struct i2c_client *second_device);
-void bmc150_set_second_device(struct i2c_client *second_device);
+void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev);
 extern const struct dev_pm_ops bmc150_accel_pm_ops;
 extern const struct regmap_config bmc150_regmap_conf;
 
#6 lore raw

PATCH v2 3/9 iio: accel: bmc150: Move check for second ACPI device into a separate function

In reply to Hans de Goede

Move the check for a second ACPI device for BOSC0200 ACPI fwnodes into a new bmc150_acpi_dual_accel_probe() helper function.

This is a preparation patch for adding support for a new "DUAL250E" ACPI Hardware-ID (HID) used on some devices.

---
Changes in v2:
- Drop comma after terminating entry of bmc150_acpi_dual_accel_ids array
- Rewrap some comments at 80 chars limit

---
 drivers/iio/accel/bmc150-accel-i2c.c | 80 ++++++++++++++++++----------
 1 file changed, 51 insertions(+), 29 deletions(-)
drivers/iio/accel/bmc150-accel-i2c.c +51 -29
index 2afaae0294ee..f7cb40f481ef 100644
@@ -21,6 +21,52 @@
 
 #include "bmc150-accel.h"
 
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id bmc150_acpi_dual_accel_ids[] = {
+	{"BOSC0200"},
+	{ }
+};
+
+/*
+ * Some acpi_devices describe 2 accelerometers in a single ACPI device,
+ * try instantiating a second i2c_client for an I2cSerialBusV2 ACPI resource
+ * with index 1.
+ */
+static void bmc150_acpi_dual_accel_probe(struct i2c_client *client)
+{
+	struct acpi_device *adev = ACPI_COMPANION(&client->dev);
+	struct i2c_client *second_dev;
+	struct i2c_board_info board_info = {
+		.type = "bmc150_accel",
+		/*
+		 * The 2nd accel sits in the base of 2-in-1s. Note this name is
+		 * static, as there should never be more then 1 BOSC0200 ACPI
+		 * node with 2 accelerometers in it.
+		 */
+		.dev_name = "BOSC0200:base",
+		.fwnode = client->dev.fwnode,
+		.irq = -ENOENT,
+	};
+
+	if (acpi_match_device_ids(adev, bmc150_acpi_dual_accel_ids))
+		return;
+
+	second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
+	if (!IS_ERR(second_dev))
+		bmc150_set_second_device(client, second_dev);
+}
+
+static void bmc150_acpi_dual_accel_remove(struct i2c_client *client)
+{
+	struct i2c_client *second_dev = bmc150_get_second_device(client);
+
+	i2c_unregister_device(second_dev);
+}
+#else
+static void bmc150_acpi_dual_accel_probe(struct i2c_client *client) {}
+static void bmc150_acpi_dual_accel_remove(struct i2c_client *client) {}
+#endif
+
 static int bmc150_accel_probe(struct i2c_client *client,
 			      const struct i2c_device_id *id)
 {
@@ -30,7 +76,6 @@ static int bmc150_accel_probe(struct i2c_client *client,
 		i2c_check_functionality(client->adapter, I2C_FUNC_I2C) ||
 		i2c_check_functionality(client->adapter,
 					I2C_FUNC_SMBUS_READ_I2C_BLOCK);
-	struct acpi_device __maybe_unused *adev;
 	int ret;
 
 	regmap = devm_regmap_init_i2c(client, &bmc150_regmap_conf);
@@ -47,41 +92,18 @@ static int bmc150_accel_probe(struct i2c_client *client,
 		return ret;
 
 	/*
-	 * Some BOSC0200 acpi_devices describe 2 accelerometers in a single ACPI
-	 * device, try instantiating a second i2c_client for an I2cSerialBusV2
-	 * ACPI resource with index 1. The !id check avoids recursion when
-	 * bmc150_accel_probe() gets called for the second client.
+	 * The !id check avoids recursion when probe() gets called
+	 * for the second client.
 	 */
-#ifdef CONFIG_ACPI
-	adev = ACPI_COMPANION(&client->dev);
-	if (!id && adev && strcmp(acpi_device_hid(adev), "BOSC0200") == 0) {
-		struct i2c_board_info board_info = {
-			.type = "bmc150_accel",
-			/*
-			 * The 2nd accel sits in the base of 2-in-1s. Note this
-			 * name is static, as there should never be more then 1
-			 * BOSC0200 ACPI node with 2 accelerometers in it.
-			 */
-			.dev_name = "BOSC0200:base",
-			.fwnode = client->dev.fwnode,
-			.irq = -ENOENT,
-		};
-		struct i2c_client *second_dev;
-
-		second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
-		if (!IS_ERR(second_dev))
-			bmc150_set_second_device(client, second_dev);
-	}
-#endif
+	if (!id && has_acpi_companion(&client->dev))
+		bmc150_acpi_dual_accel_probe(client);
 
 	return 0;
 }
 
 static int bmc150_accel_remove(struct i2c_client *client)
 {
-	struct i2c_client *second_dev = bmc150_get_second_device(client);
-
-	i2c_unregister_device(second_dev);
+	bmc150_acpi_dual_accel_remove(client);
 
 	return bmc150_accel_core_remove(&client->dev);
 }
Signature · 1 line
2.31.1
#7 lore raw

PATCH v2 4/9 iio: accel: bmc150: Add support for dual-accelerometers with a DUAL250E HID

In reply to Hans de Goede

The Lenovo Yoga 300-11IBR has a ACPI fwnode with a HID of DUAL250E which contains I2C and IRQ resources for 2 accelerometers, 1 in the display and one in the base of the device. Add support for this.

---
Changes in v2:
- Rewrap some comments at 80 chars limit
- Use acpi_dev_gpio_irq_get() instead of acpi_dev_gpio_irq_get_by()

---
 drivers/iio/accel/bmc150-accel-i2c.c | 19 ++++++++++++-------
 1 file changed, 12 insertions(+), 7 deletions(-)
drivers/iio/accel/bmc150-accel-i2c.c +12 -7
index f7cb40f481ef..41b4c9e22d60 100644
@@ -24,6 +24,7 @@
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id bmc150_acpi_dual_accel_ids[] = {
 	{"BOSC0200"},
+	{"DUAL250E"},
 	{ }
 };
 
@@ -36,21 +37,24 @@ static void bmc150_acpi_dual_accel_probe(struct i2c_client *client)
 {
 	struct acpi_device *adev = ACPI_COMPANION(&client->dev);
 	struct i2c_client *second_dev;
+	char dev_name[16];
 	struct i2c_board_info board_info = {
 		.type = "bmc150_accel",
-		/*
-		 * The 2nd accel sits in the base of 2-in-1s. Note this name is
-		 * static, as there should never be more then 1 BOSC0200 ACPI
-		 * node with 2 accelerometers in it.
-		 */
-		.dev_name = "BOSC0200:base",
+		.dev_name = dev_name,
 		.fwnode = client->dev.fwnode,
-		.irq = -ENOENT,
 	};
 
 	if (acpi_match_device_ids(adev, bmc150_acpi_dual_accel_ids))
 		return;
 
+	/*
+	 * The 2nd accel sits in the base of 2-in-1s. The suffix is static, as
+	 * there should never be more then 1 ACPI node with 2 accelerometers.
+	 */
+	snprintf(dev_name, sizeof(dev_name), "%s:base", acpi_device_hid(adev));
+
+	board_info.irq = acpi_dev_gpio_irq_get(adev, 1);
+
 	second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
 	if (!IS_ERR(second_dev))
 		bmc150_set_second_device(client, second_dev);
@@ -118,6 +122,7 @@ static const struct acpi_device_id bmc150_accel_acpi_match[] = {
 	{"BMA222E",	bma222e},
 	{"BMA0280",	bma280},
 	{"BOSC0200"},
+	{"DUAL250E"},
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, bmc150_accel_acpi_match);
Signature · 1 line
2.31.1
#8 lore raw

PATCH v2 5/9 iio: accel: bmc150: Move struct bmc150_accel_data definition to bmc150-accel.h

In reply to Hans de Goede

Further patches to bmc150-accel-i2c.c need to store some extra info (on top of the second_dev pointer) in the bmc150_accel_data struct, rather then adding yet more accessor functions for this lets just move the struct bmc150_accel_data definition to bmc150-accel.h.

---
 drivers/iio/accel/bmc150-accel-core.c | 53 -----------------------
 drivers/iio/accel/bmc150-accel.h      | 61 +++++++++++++++++++++++++++
 2 files changed, 61 insertions(+), 53 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +0 -53
index 8ff358c37a81..0d76df9e08eb 100644
@@ -157,59 +157,6 @@ struct bmc150_accel_chip_info {
 	const struct bmc150_scale_info scale_table[4];
 };
 
-struct bmc150_accel_interrupt {
-	const struct bmc150_accel_interrupt_info *info;
-	atomic_t users;
-};
-
-struct bmc150_accel_trigger {
-	struct bmc150_accel_data *data;
-	struct iio_trigger *indio_trig;
-	int (*setup)(struct bmc150_accel_trigger *t, bool state);
-	int intr;
-	bool enabled;
-};
-
-enum bmc150_accel_interrupt_id {
-	BMC150_ACCEL_INT_DATA_READY,
-	BMC150_ACCEL_INT_ANY_MOTION,
-	BMC150_ACCEL_INT_WATERMARK,
-	BMC150_ACCEL_INTERRUPTS,
-};
-
-enum bmc150_accel_trigger_id {
-	BMC150_ACCEL_TRIGGER_DATA_READY,
-	BMC150_ACCEL_TRIGGER_ANY_MOTION,
-	BMC150_ACCEL_TRIGGERS,
-};
-
-struct bmc150_accel_data {
-	struct regmap *regmap;
-	struct regulator_bulk_data regulators[2];
-	struct bmc150_accel_interrupt interrupts[BMC150_ACCEL_INTERRUPTS];
-	struct bmc150_accel_trigger triggers[BMC150_ACCEL_TRIGGERS];
-	struct mutex mutex;
-	u8 fifo_mode, watermark;
-	s16 buffer[8];
-	/*
-	 * Ensure there is sufficient space and correct alignment for
-	 * the timestamp if enabled
-	 */
-	struct {
-		__le16 channels[3];
-		s64 ts __aligned(8);
-	} scan;
-	u8 bw_bits;
-	u32 slope_dur;
-	u32 slope_thres;
-	u32 range;
-	int ev_enable_state;
-	int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
-	const struct bmc150_accel_chip_info *chip_info;
-	struct i2c_client *second_device;
-	struct iio_mount_matrix orientation;
-};
-
 static const struct {
 	int val;
 	int val2;
drivers/iio/accel/bmc150-accel.h +61 -0

68 lines not on this page · raw message

Signature · 1 line
2.31.1
#9 lore raw

PATCH v2 6/9 iio: accel: bmc150: Remove bmc150_set/get_second_device() accessor functions

In reply to Hans de Goede

Now that the definition of the bmc150_accel_data struct is no longer private to bmc150-accel-core.c, bmc150-accel-i2c.c can simply directly access the second_dev member and the accessor functions are no longer necessary.

Note if the i2c_acpi_new_device() for the second-client now fails, an ERR_PTR gets stored in data->second_dev this is fine since it is only ever passed to i2c_unregister_device() which has an IS_ERR_OR_NULL() check.

---
 drivers/iio/accel/bmc150-accel-core.c | 16 ----------------
 drivers/iio/accel/bmc150-accel-i2c.c  | 10 ++++------
 drivers/iio/accel/bmc150-accel.h      |  2 --
 3 files changed, 4 insertions(+), 24 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +0 -16
index 0d76df9e08eb..0291512648b2 100644
@@ -1754,22 +1754,6 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 }
 EXPORT_SYMBOL_GPL(bmc150_accel_core_probe);
 
-struct i2c_client *bmc150_get_second_device(struct i2c_client *client)
-{
-	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
-
-	return data->second_device;
-}
-EXPORT_SYMBOL_GPL(bmc150_get_second_device);
-
-void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev)
-{
-	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
-
-	data->second_device = second_dev;
-}
-EXPORT_SYMBOL_GPL(bmc150_set_second_device);
-
 int bmc150_accel_core_remove(struct device *dev)
 {
 	struct iio_dev *indio_dev = dev_get_drvdata(dev);
drivers/iio/accel/bmc150-accel-i2c.c +4 -6
index 41b4c9e22d60..ab0cda8ff8fa 100644
@@ -35,8 +35,8 @@ static const struct acpi_device_id bmc150_acpi_dual_accel_ids[] = {
  */
 static void bmc150_acpi_dual_accel_probe(struct i2c_client *client)
 {
+	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 	struct acpi_device *adev = ACPI_COMPANION(&client->dev);
-	struct i2c_client *second_dev;
 	char dev_name[16];
 	struct i2c_board_info board_info = {
 		.type = "bmc150_accel",
@@ -55,16 +55,14 @@ static void bmc150_acpi_dual_accel_probe(struct i2c_client *client)
 
 	board_info.irq = acpi_dev_gpio_irq_get(adev, 1);
 
-	second_dev = i2c_acpi_new_device(&client->dev, 1, &board_info);
-	if (!IS_ERR(second_dev))
-		bmc150_set_second_device(client, second_dev);
+	data->second_device = i2c_acpi_new_device(&client->dev, 1, &board_info);
 }
 
 static void bmc150_acpi_dual_accel_remove(struct i2c_client *client)
 {
-	struct i2c_client *second_dev = bmc150_get_second_device(client);
+	struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
 
-	i2c_unregister_device(second_dev);
+	i2c_unregister_device(data->second_device);
 }
 #else
 static void bmc150_acpi_dual_accel_probe(struct i2c_client *client) {}
drivers/iio/accel/bmc150-accel.h +0 -2
index f503c5b5801e..5da6fd32bac5 100644
@@ -78,8 +78,6 @@ enum {
 int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 			    const char *name, bool block_supported);
 int bmc150_accel_core_remove(struct device *dev);
-struct i2c_client *bmc150_get_second_device(struct i2c_client *second_device);
-void bmc150_set_second_device(struct i2c_client *client, struct i2c_client *second_dev);
 extern const struct dev_pm_ops bmc150_accel_pm_ops;
 extern const struct regmap_config bmc150_regmap_conf;
 
Signature · 1 line
2.31.1
#10 lore raw

PATCH v2 7/9 iio: accel: bmc150: Add support for DUAL250E ACPI DSM for setting the hinge angle

In reply to Hans de Goede

Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels to allow the OS to determine the angle between the display and the base of the device, so that the OS can determine if the 2-in-1 is in laptop or in tablet-mode.

On Windows both accelerometers are read (polled) by a special service and this service calls the DSM (Device Specific Method), which in turn translates the angles to one of laptop/tablet/tent/stand mode and then notifies the EC about the new mode and the EC then enables or disables the builtin keyboard and touchpad based in the mode.

When the 2-in-1 is powered-on or resumed folded in tablet mode the EC senses this independent of the DSM by using a HALL effect sensor which senses that the keyboard has been folded away behind the display.

At power-on or resume the EC disables the keyboard based on this and the only way to get the keyboard to work after this is to call the DSM to re-enable it.

Call the DSM on probe() and resume() to fix the keyboard not working when powered-on / resumed in tablet-mode.

This patch was developed and tested on a Lenovo Yoga 300-IBR.

---
Changes in v2:
- Use acpi_dev_hid_uid_match() to check that we are dealing with a "DUAL250E" device in bmc150_acpi_set_angle_dsm()
- Rewrap some comments at 80 chars limit

---
 drivers/iio/accel/bmc150-accel-core.c |   3 +
 drivers/iio/accel/bmc150-accel-i2c.c  | 110 ++++++++++++++++++++++++++
 drivers/iio/accel/bmc150-accel.h      |   3 +
 3 files changed, 116 insertions(+)
drivers/iio/accel/bmc150-accel-core.c +3 -0
index 0291512648b2..932007895f18 100644
@@ -1803,6 +1803,9 @@ static int bmc150_accel_resume(struct device *dev)
 	bmc150_accel_fifo_set_mode(data);
 	mutex_unlock(&data->mutex);
 
+	if (data->resume_callback)
+		data->resume_callback(dev);
+
 	return 0;
 }
 #endif
drivers/iio/accel/bmc150-accel-i2c.c +110 -0

128 lines not on this page · raw message

drivers/iio/accel/bmc150-accel.h +3 -0
index 5da6fd32bac5..d67d6ed6ae77 100644
@@ -6,6 +6,7 @@
 #include <linux/iio/iio.h>
 #include <linux/mutex.h>
 #include <linux/regulator/consumer.h>
+#include <linux/workqueue.h>
 
 struct regmap;
 struct i2c_client;
@@ -62,6 +63,8 @@ struct bmc150_accel_data {
 	int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
 	const struct bmc150_accel_chip_info *chip_info;
 	struct i2c_client *second_device;
+	void (*resume_callback)(struct device *dev);
+	struct delayed_work resume_work;
 	struct iio_mount_matrix orientation;
 };
 
Signature · 1 line
2.31.1
#11 lore raw

PATCH v2 8/9 iio: accel: bmc150: Refactor bmc150_apply_acpi_orientation()

In reply to Hans de Goede

Factor the BOSC0200 ACPI HID handling out into a new bmc150_apply_bosc0200_acpi_orientation() function and make bmc150_apply_acpi_orientation() call that when dealing with a BOSC0200 ACPI device (and make it return false otherwise).

This is a preparation patch for adding special handling for other ACPI HIDs (the "DUAL250E" HID).

---
Changes in v2:
- This is a new patch in v2 of this patch-set

---
 drivers/iio/accel/bmc150-accel-core.c | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)
drivers/iio/accel/bmc150-accel-core.c +13 -5
index 932007895f18..f685ed617424 100644
@@ -386,8 +386,8 @@ static int bmc150_accel_set_power_state(struct bmc150_accel_data *data, bool on)
  * Onda V80 plus
  * Predia Basic Tablet
  */
-static bool bmc150_apply_acpi_orientation(struct device *dev,
-					  struct iio_mount_matrix *orientation)
+static bool bmc150_apply_bosc0200_acpi_orientation(struct device *dev,
+						   struct iio_mount_matrix *orientation)
 {
 	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
 	struct iio_dev *indio_dev = dev_get_drvdata(dev);
@@ -397,9 +397,6 @@ static bool bmc150_apply_acpi_orientation(struct device *dev,
 	acpi_status status;
 	int i, j, val[3];
 
-	if (!adev || !acpi_dev_hid_uid_match(adev, "BOSC0200", NULL))
-		return false;
-
 	if (strcmp(dev_name(dev), "i2c-BOSC0200:base") == 0) {
 		alt_name = "ROMK";
 		label = "accel-base";
@@ -455,6 +452,17 @@ static bool bmc150_apply_acpi_orientation(struct device *dev,
 	kfree(buffer.pointer);
 	return false;
 }
+
+static bool bmc150_apply_acpi_orientation(struct device *dev,
+					  struct iio_mount_matrix *orientation)
+{
+	struct acpi_device *adev = ACPI_COMPANION(dev);
+
+	if (adev && acpi_dev_hid_uid_match(adev, "BOSC0200", NULL))
+		return bmc150_apply_bosc0200_acpi_orientation(dev, orientation);
+
+	return false;
+}
 #else
 static bool bmc150_apply_acpi_orientation(struct device *dev,
 					  struct iio_mount_matrix *orientation)
Signature · 1 line
2.31.1
#12 lore raw

PATCH v2 9/9 iio: accel: bmc150: Set label based on accel-location for ACPI DUAL250E fwnodes

In reply to Hans de Goede

Some Yoga laptops with 1 accelerometer in the display and 1 in the base, use an ACPI HID of DUAL250E instead of BOSC0200.

Set the iio-device's label for DUAL250E devices to a value indicating which sensor is which, mirroring how we do this for BOSC0200 dual sensor devices.

Note the DUAL250E fwnode unfortunately does not include a mount-matrix.

---
Changes in v2:
- Rebase on top of the new "iio: accel: bmc150: Refactor bmc150_apply_acpi_orientation()" patch

---
 drivers/iio/accel/bmc150-accel-core.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
drivers/iio/accel/bmc150-accel-core.c +16 -0
index f685ed617424..95a9ef2d333e 100644
@@ -453,6 +453,19 @@ static bool bmc150_apply_bosc0200_acpi_orientation(struct device *dev,
 	return false;
 }
 
+static bool bmc150_apply_dual250e_acpi_orientation(struct device *dev,
+						   struct iio_mount_matrix *orientation)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+
+	if (strcmp(dev_name(dev), "i2c-DUAL250E:base") == 0)
+		indio_dev->label = "accel-base";
+	else
+		indio_dev->label = "accel-display";
+
+	return false; /* DUAL250E fwnodes have no mount matrix info */
+}
+
 static bool bmc150_apply_acpi_orientation(struct device *dev,
 					  struct iio_mount_matrix *orientation)
 {
@@ -461,6 +474,9 @@ static bool bmc150_apply_acpi_orientation(struct device *dev,
 	if (adev && acpi_dev_hid_uid_match(adev, "BOSC0200", NULL))
 		return bmc150_apply_bosc0200_acpi_orientation(dev, orientation);
 
+	if (adev && acpi_dev_hid_uid_match(adev, "DUAL250E", NULL))
+		return bmc150_apply_dual250e_acpi_orientation(dev, orientation);
+
 	return false;
 }
 #else
Signature · 1 line
2.31.1
Reviewed-by on the v2 series
#13 lore raw
In reply to Hans de Goede
Quoted 35 lines · Hans de Goede

Hi all,

Here is v2 of this series, addressing Andy's review remarks and rewrap some comments at 80 chars limit.

For more info here is the v1 cover-letter:

Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels to allow the OS to determine the angle between the display and the base of the device, so that the OS can determine if the 2-in-1 is in laptop or in tablet-mode.

We already support this setup on devices using a single ACPI node with a HID of "BOSC0200" to describe both accelerometers. This patch set extends this support to also support the same setup but then using a HID of "DUAL250E".

While testing this I found some crashes on rmmod, patches 1-2 fix those patches, patch 3 does some refactoring and patch 4 adds support for the "DUAL250E" HID.

Unfortunately we need some more special handling though, which the rest of the patches are for.

On Windows both accelerometers are read (polled) by a special service and this service calls a DSM (Device Specific Method), which in turn translates the angles to one of laptop/tablet/tent/stand mode and then notifies the EC about the new mode and the EC then enables or disables the builtin keyboard and touchpad based in the mode.

When the 2-in-1 is powered-on or resumed folded in tablet mode the EC senses this independent of the DSM by using a HALL effect sensor which senses that the keyboard has been folded away behind the display.

Quoted 7 lines

At power-on or resume the EC disables the keyboard based on this and the only way to get the keyboard to work after this is to call the DSM to re-enable it (similar to how we also need to call a special DSM in the kxcjk-1013.c accel driver to re-enable the keyboard).

Patches 5-7 deal with the DSM mess and patch 8 adds labels to the 2 accelerometers specifying which one is which.

Thanks!

Quoted 32 lines

Regards,

Hans

Hans de Goede (9):
iio: accel: bmc150: Fix dereferencing the wrong pointer in
bmc150_get/set_second_device
iio: accel: bmc150: Don't make the remove function of the second
accelerometer unregister itself
iio: accel: bmc150: Move check for second ACPI device into a separate
function
iio: accel: bmc150: Add support for dual-accelerometers with a
DUAL250E HID
iio: accel: bmc150: Move struct bmc150_accel_data definition to

    bmc150-accel.h

iio: accel: bmc150: Remove bmc150_set/get_second_device() accessor
functions
iio: accel: bmc150: Add support for DUAL250E ACPI DSM for setting the
hinge angle
iio: accel: bmc150: Refactor bmc150_apply_acpi_orientation()
iio: accel: bmc150: Set label based on accel-location for ACPI
DUAL250E fwnodes

 drivers/iio/accel/bmc150-accel-core.c | 110 +++++----------
 drivers/iio/accel/bmc150-accel-i2c.c  | 193 ++++++++++++++++++++++----
 drivers/iio/accel/bmc150-accel.h      |  66 ++++++++-
 3 files changed, 260 insertions(+), 109 deletions(-)

--
2.31.1

Signature · 2 lines
With Best Regards,
Andy Shevchenko
maintainer
#14 lore raw
Quoted 41 lines · On Sun, 23 May 2021 22:08:57 +0300 Andy Shevchenko <[email protected]>…
Quoted 40 lines · Hans de Goede

Hi all,

Here is v2 of this series, addressing Andy's review remarks and rewrap some comments at 80 chars limit.

For more info here is the v1 cover-letter:

Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels to allow the OS to determine the angle between the display and the base of the device, so that the OS can determine if the 2-in-1 is in laptop or in tablet-mode.

We already support this setup on devices using a single ACPI node with a HID of "BOSC0200" to describe both accelerometers. This patch set extends this support to also support the same setup but then using a HID of "DUAL250E".

While testing this I found some crashes on rmmod, patches 1-2 fix those patches, patch 3 does some refactoring and patch 4 adds support for the "DUAL250E" HID.

Unfortunately we need some more special handling though, which the rest of the patches are for.

On Windows both accelerometers are read (polled) by a special service and this service calls a DSM (Device Specific Method), which in turn translates the angles to one of laptop/tablet/tent/stand mode and then notifies the EC about the new mode and the EC then enables or disables the builtin keyboard and touchpad based in the mode.

When the 2-in-1 is powered-on or resumed folded in tablet mode the EC senses this independent of the DSM by using a HALL effect sensor which senses that the keyboard has been folded away behind the display.

At power-on or resume the EC disables the keyboard based on this and the only way to get the keyboard to work after this is to call the DSM to re-enable it (similar to how we also need to call a special DSM in the kxcjk-1013.c accel driver to re-enable the keyboard).

Quoted 5 lines
Quoted 2 lines

Patches 5-7 deal with the DSM mess and patch 8 adds labels to the 2 accelerometers specifying which one is which.

Thanks!

Whole series now applied to the togreg branch of iio.git and pushed out as testing to give 0-day a chance to pick on it.

Thanks,

Jonathan

Quoted 35 lines
Quoted 33 lines

Regards,

Hans

Hans de Goede (9):
iio: accel: bmc150: Fix dereferencing the wrong pointer in
bmc150_get/set_second_device
iio: accel: bmc150: Don't make the remove function of the second
accelerometer unregister itself
iio: accel: bmc150: Move check for second ACPI device into a separate
function
iio: accel: bmc150: Add support for dual-accelerometers with a
DUAL250E HID
iio: accel: bmc150: Move struct bmc150_accel_data definition to

    bmc150-accel.h

iio: accel: bmc150: Remove bmc150_set/get_second_device() accessor
functions
iio: accel: bmc150: Add support for DUAL250E ACPI DSM for setting the
hinge angle
iio: accel: bmc150: Refactor bmc150_apply_acpi_orientation()
iio: accel: bmc150: Set label based on accel-location for ACPI
DUAL250E fwnodes

 drivers/iio/accel/bmc150-accel-core.c | 110 +++++----------
 drivers/iio/accel/bmc150-accel-i2c.c  | 193 ++++++++++++++++++++++----
 drivers/iio/accel/bmc150-accel.h      |  66 ++++++++-
 3 files changed, 260 insertions(+), 109 deletions(-)

--
2.31.1