imx: support for conga-QMX8 board
Subsystems (3)
PATCH v7 1/1 imx: support for conga-QMX8 board
Add i.MX8QM qmx8 congatec board support
U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000
switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet@5b040000 address not set.
No ethernet found.
Hit any key to stop autoboot: 0
---
These changes are based on this vendor tree:
git.congatec.com/imx8_early_access/imx8_uboot_internal.git
Changes for v7:
- removed superflous include in board/congatec/common/mmc.c
- added congatec to doc/board/index.rst
Changes for v6:
- fixed build warnings because of missing prototypes
Changes for v5:
- fixed checkpatch errors
- fixed some checkpatch warnings
Changes for v4:
- fixed missing DTS file in MAINTAINERS
- replaced bd_t with struct bd_info
- replaced README with imx8qm-dmsse20-a1.rst
- move CMD_FUSE to Kconfig
- replaced power_domain_lookup_name with imx8_power_domain_lookup_name
Changes for v3:
- include log.h
- include delay.h
- improved README
- set phy register to six
- Remove 'fdt_high' and 'initrd_high' environment variables
- set CONFIG_SYS_BOOTMAPSZ to 256MB
- increased CONFIG_SYS_FSL_USDHC_NUM to 3
Changes for v2:
- added USDHC3_BASE_ADDR
- replaced CONFIG_FSL_ESDHC with CONFIG_FSL_ESDHC_IMX
- set CONFIG_FEC_MXC_PHYADDR to -1
- moved CONFIG_ENV_SIZE and CONFIG_ENV_OFFSET to defconfig
arch/arm/dts/Makefile | 1 + arch/arm/dts/imx8qm-cgtqmx8.dts | 404 ++++++++++++++++++++++++ arch/arm/mach-imx/imx8/Kconfig | 7 + board/congatec/cgtqmx8/Kconfig | 14 + board/congatec/cgtqmx8/MAINTAINERS | 7 + board/congatec/cgtqmx8/Makefile | 11 + board/congatec/cgtqmx8/cgtqmx8.c | 460 ++++++++++++++++++++++++++++ board/congatec/cgtqmx8/imximage.cfg | 21 ++ board/congatec/cgtqmx8/spl.c | 77 +++++ board/congatec/common/Kconfig | 48 +++ board/congatec/common/Makefile | 23 ++ board/congatec/common/mmc.c | 49 +++ configs/cgtqmx8_defconfig | 86 ++++++ doc/board/congatec/cgtqmx8.rst | 70 +++++ doc/board/congatec/index.rst | 9 + doc/board/index.rst | 1 + include/configs/cgtqmx8.h | 181 +++++++++++ 17 files changed, 1469 insertions(+) create mode 100644 arch/arm/dts/imx8qm-cgtqmx8.dts create mode 100644 board/congatec/cgtqmx8/Kconfig create mode 100644 board/congatec/cgtqmx8/MAINTAINERS create mode 100644 board/congatec/cgtqmx8/Makefile create mode 100644 board/congatec/cgtqmx8/cgtqmx8.c create mode 100644 board/congatec/cgtqmx8/imximage.cfg create mode 100644 board/congatec/cgtqmx8/spl.c create mode 100644 board/congatec/common/Kconfig create mode 100644 board/congatec/common/Makefile create mode 100644 board/congatec/common/mmc.c create mode 100644 configs/cgtqmx8_defconfig create mode 100644 doc/board/congatec/cgtqmx8.rst create mode 100644 doc/board/congatec/index.rst create mode 100644 include/configs/cgtqmx8.h
arch/arm/dts/Makefile +1 -0
@@ -836,6 +836,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-com.dtb \ dtb-$(CONFIG_ARCH_IMX8) += \ fsl-imx8qm-apalis.dtb \ fsl-imx8qm-mek.dtb \ + imx8qm-cgtqmx8.dtb \ imx8qm-rom7720-a1.dtb \ fsl-imx8qxp-ai_ml.dtb \ fsl-imx8qxp-colibri.dtb \
arch/arm/dts/imx8qm-cgtqmx8.dts new file +404 -0
404 lines not on this page · raw message
arch/arm/mach-imx/imx8/Kconfig +7 -0
@@ -86,6 +86,12 @@ config TARGET_IMX8QM_MEK select BOARD_LATE_INIT select IMX8QM +config TARGET_CONGA_QMX8 + bool "Support congatec conga-QMX8 board" + select BOARD_LATE_INIT + select SUPPORT_SPL + select IMX8QM + config TARGET_IMX8QM_ROM7720_A1 bool "Support i.MX8QM ROM-7720-A1" select BOARD_LATE_INIT
@@ -101,6 +107,7 @@ endchoice source "board/freescale/imx8qm_mek/Kconfig" source "board/freescale/imx8qxp_mek/Kconfig" +source "board/congatec/cgtqmx8/Kconfig" source "board/advantech/imx8qm_rom7720_a1/Kconfig" source "board/toradex/apalis-imx8/Kconfig" source "board/toradex/colibri-imx8x/Kconfig"
board/congatec/cgtqmx8/Kconfig new file +14 -0
@@ -0,0 +1,14 @@ +if TARGET_CONGA_QMX8 + +config SYS_BOARD + default "cgtqmx8" + +config SYS_VENDOR + default "congatec" + +config SYS_CONFIG_NAME + default "cgtqmx8" + +source "board/congatec/common/Kconfig" + +endif
board/congatec/cgtqmx8/MAINTAINERS new file +7 -0
@@ -0,0 +1,7 @@ +i.MX8QM CGTQMX8 BOARD +M: Oliver Graute <[email protected]> +S: Maintained +F: board/congatec/cgtqmx8/ +F: arch/arm/dts/imx8qm-cgtqmx8.dts +F: include/configs/cgtqmx8.h +F: configs/cgtqmx8_defconfig
board/congatec/cgtqmx8/Makefile new file +11 -0
@@ -0,0 +1,11 @@ +# +# Copyright 2017 NXP +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += cgtqmx8.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +endif
board/congatec/cgtqmx8/cgtqmx8.c new file +460 -0
460 lines not on this page · raw message
board/congatec/cgtqmx8/imximage.cfg new file +21 -0
@@ -0,0 +1,21 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2018 NXP + */ + +#define __ASSEMBLY__ + +/* Boot from SD, sector size 0x400 */ +BOOT_FROM SD 0x400 +/* SoC type IMX8QM */ +SOC_TYPE IMX8QM +/* Append seco container image */ +APPEND mx8qm-ahab-container.img +/* Create the 2nd container */ +CONTAINER +/* Add scfw image with exec attribute */ +IMAGE SCU mx8qm-val-scfw-tcm.bin +/* Add ATF image with exec attribute */ +IMAGE A35 bl31.bin 0x80000000 +/* Add U-Boot image with load attribute */ +DATA A35 u-boot-dtb.bin 0x80020000
board/congatec/cgtqmx8/spl.c new file +77 -0
77 lines not on this page · raw message
board/congatec/common/Kconfig new file +48 -0
48 lines not on this page · raw message
board/congatec/common/Makefile new file +23 -0
@@ -0,0 +1,23 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, [email protected]. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL +# necessary to create built-in.o +obj- := __dummy__.o +else + +obj-y += mmc.o + +endif
board/congatec/common/mmc.c new file +49 -0
49 lines not on this page · raw message
configs/cgtqmx8_defconfig new file +86 -0
86 lines not on this page · raw message
doc/board/congatec/cgtqmx8.rst new file +70 -0
70 lines not on this page · raw message
doc/board/congatec/index.rst new file +9 -0
@@ -0,0 +1,9 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Congatec +======== + +.. toctree:: + :maxdepth: 2 + + cgtqmx8.rst
doc/board/index.rst +1 -0
@@ -11,6 +11,7 @@ Board-specific doc AndesTech/index amlogic/index atmel/index + congatec/index coreboot/index emulation/index freescale/index
include/configs/cgtqmx8.h new file +181 -0
181 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v7 1/1 imx: support for conga-QMX8 board
Quoted 19 lines
Add i.MX8QM qmx8 congatec board support
U-Boot 2021.07-rc3-00528-gc9a966d9dd (May 31 2021 - 15:21:25 +0200)CPU: NXP i.MX8QM RevB A53 at 1200 MHz Model: Congatec QMX8 Qseven series Board: conga-QMX8 Build: SCFW 494c97f3, SECO-FW d63fdb21, ATF 09c5cc9 Boot: SD2 DRAM: 6 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial@5a060000 Out: serial@5a060000 Err: serial@5a060000switch to partitions #0, OK
mmc2 is current device
Net:
Error: ethernet@5b040000 address not set.
No ethernet found.
Hit any key to stop autoboot: 0
Quoted 7 lines
Signed-off-by Oliver Graute <[email protected]>Cc Stefano Babic <[email protected]>Cc Fabio Estevam <[email protected]>Cc Peng Fan <[email protected]>Cc Simon Glass <[email protected]>Cc Ye Li <[email protected]>Cc uboot-imx <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================