fit: Load DTO into temporary buffer and ignore load address
PATCH 1/1 fit: Load DTO into temporary buffer and ignore load address
The current fitImage DTO implementation expects each fitImage image subnode containing DTO to have 'load' property, pointing somewhere into memory where the DTO will be loaded. The address in the 'load' property must be different then the base DT load address and there must be sufficient amount of space between those two addresses. Selecting and using such hard-coded addresses is fragile, error prone and difficult to port even across devices with the same SoC and different DRAM sizes.
The DTO cannot be applied in-place because fdt_overlay_apply_verbose() modifies the DTO when applying it onto the base DT, so if the DTO was used in place within the fitImage, call to fdt_overlay_apply_verbose() would corrupt the fitImage.
Instead of copying the DTO to a specific hard-coded load address, allocate a buffer, copy the DTO into that buffer, apply the DTO onto the base DT, and free the buffer.
The upside of this approach is that it is no longer necessary to select and hard-code specific DTO load address into the DTO. The slight downside is the new malloc()/free() overhead for each DTO, but that is negligible (*).
(*) on iMX8MM/MN and STM32MP1
--- common/image-fit.c | 31 +++++++++++++++++++++++++++---- 1 file changed, 27 insertions(+), 4 deletions(-)
common/image-fit.c +27 -4
@@ -2267,10 +2267,10 @@ int boot_get_fdt_fit(bootm_headers_t *images, ulong addr,ulong load, len;#ifdef CONFIG_OF_LIBFDT_OVERLAY ulong image_start, image_end; -ulong ovload, ovlen; +ulong ovload, ovlen, ovcopylen;const char *uconfig;const char *uname; -void *base, *ov; +void *base, *ov, *ovcopy =NULL ;int i, err, noffset, ov_noffset;#endif
@@ -2360,7 +2360,7 @@ int boot_get_fdt_fit(bootm_headers_t *images, ulong addr, addr, &uname, &uconfig, arch,IH_TYPE_FLATDT ,BOOTSTAGE_ID_FIT_FDT_START , - FIT_LOAD_REQUIRED, &ovload, &ovlen); + FIT_LOAD_IGNORED, &ovload, &ovlen);if (ov_noffset <0 ) {printf ("load of %s failed\n" , uname);continue ;
@@ -2369,6 +2369,21 @@ int boot_get_fdt_fit(bootm_headers_t *images, ulong addr, uname, ovload, ovlen); ov =map_sysmem (ovload, ovlen); + ovcopylen =ALIGN (fdt_totalsize (ov),SZ_4K ); + ovcopy =malloc (ovcopylen); +if (!ovcopy) { +printf ("failed to duplicate DTO before application\n" ); + fdt_noffset = -ENOMEM ; + goto out; + } + + err =fdt_open_into (ov, ovcopy, ovcopylen); +if (err <0 ) { +printf ("failed on fdt_open_into for DTO\n" ); + fdt_noffset = err; + goto out; + } + base =map_sysmem (load, len + ovlen); err =fdt_open_into (base, base, len + ovlen);if (err <0 ) {
@@ -2376,14 +2391,18 @@ int boot_get_fdt_fit(bootm_headers_t *images, ulong addr, fdt_noffset = err; goto out; } +/* the verbose method prints out messages on error */ - err =fdt_overlay_apply_verbose (base, ov); + err =fdt_overlay_apply_verbose (base, ovcopy);if (err <0 ) { fdt_noffset = err; goto out; }fdt_pack (base); len =fdt_totalsize (base); + +free (ovcopy); + ovcopy =NULL ; }#else printf ("config with overlays but CONFIG_OF_LIBFDT_OVERLAY not set\n" );
@@ -2400,6 +2419,10 @@ out:if (fit_uname_configp) *fit_uname_configp = fit_uname_config; +#ifdef CONFIG_OF_LIBFDT_OVERLAY +if (ovcopy) +free (ovcopy); +#endif if (fit_uname_config_copy)free (fit_uname_config_copy);return fdt_noffset;
Signature · 1 line
2.30.2
Hi,
Quoted 26 lines · Marek Vasut
The current fitImage DTO implementation expects each fitImage image subnode containing DTO to have 'load' property, pointing somewhere into memory where the DTO will be loaded. The address in the 'load' property must be different then the base DT load address and there must be sufficient amount of space between those two addresses. Selecting and using such hard-coded addresses is fragile, error prone and difficult to port even across devices with the same SoC and different DRAM sizes.
The DTO cannot be applied in-place because
fdt_overlay_apply_verbose()modifies the DTO when applying it onto the base DT, so if the DTO was used in place within the fitImage, call tofdt_overlay_apply_verbose()would corrupt the fitImage.Instead of copying the DTO to a specific hard-coded load address, allocate a buffer, copy the DTO into that buffer, apply the DTO onto the base DT, and free the buffer.
The upside of this approach is that it is no longer necessary to select and hard-code specific DTO load address into the DTO. The slight downside is the new malloc()/free() overhead for each DTO, but that is negligible (*).
(*) on iMX8MM/MN and STM32MP1
Quoted 8 lines
Signed-off-by Marek Vasut <[email protected]>Cc Pantelis Antoniou <[email protected]>Cc Simon Glass <[email protected]>Cc Tom Rini <[email protected]>--- common/image-fit.c | 31 +++++++++++++++++++++++++++---- 1 file changed, 27 insertions(+), 4 deletions(-)
Is this tested by the existing overlay test, or do we need something new?
Regards,
Simon
Quoted 38 lines · Simon Glass
Hi,
Quoted 26 lines · Marek Vasut
The current fitImage DTO implementation expects each fitImage image subnode containing DTO to have 'load' property, pointing somewhere into memory where the DTO will be loaded. The address in the 'load' property must be different then the base DT load address and there must be sufficient amount of space between those two addresses. Selecting and using such hard-coded addresses is fragile, error prone and difficult to port even across devices with the same SoC and different DRAM sizes.
The DTO cannot be applied in-place because
fdt_overlay_apply_verbose()modifies the DTO when applying it onto the base DT, so if the DTO was used in place within the fitImage, call tofdt_overlay_apply_verbose()would corrupt the fitImage.Instead of copying the DTO to a specific hard-coded load address, allocate a buffer, copy the DTO into that buffer, apply the DTO onto the base DT, and free the buffer.
The upside of this approach is that it is no longer necessary to select and hard-code specific DTO load address into the DTO. The slight downside is the new malloc()/free() overhead for each DTO, but that is negligible (*).
(*) on iMX8MM/MN and STM32MP1
Quoted 8 lines
Signed-off-by Marek Vasut <[email protected]>Cc Pantelis Antoniou <[email protected]>Cc Simon Glass <[email protected]>Cc Tom Rini <[email protected]>--- common/image-fit.c | 31 +++++++++++++++++++++++++++---- 1 file changed, 27 insertions(+), 4 deletions(-)
Quoted 1 line
Is this tested by the existing overlay test, or do we need something new?
Overlay test should be sufficient.
Simon Glass
Reviewed-byQuoted 40 lines · Marek Vasut
Quoted 38 lines · Simon Glass
Hi,
Quoted 34 lines · Marek Vasut
The current fitImage DTO implementation expects each fitImage image subnode containing DTO to have 'load' property, pointing somewhere into memory where the DTO will be loaded. The address in the 'load' property must be different then the base DT load address and there must be sufficient amount of space between those two addresses. Selecting and using such hard-coded addresses is fragile, error prone and difficult to port even across devices with the same SoC and different DRAM sizes.
The DTO cannot be applied in-place because
fdt_overlay_apply_verbose()modifies the DTO when applying it onto the base DT, so if the DTO was used in place within the fitImage, call tofdt_overlay_apply_verbose()would corrupt the fitImage.Instead of copying the DTO to a specific hard-coded load address, allocate a buffer, copy the DTO into that buffer, apply the DTO onto the base DT, and free the buffer.
The upside of this approach is that it is no longer necessary to select and hard-code specific DTO load address into the DTO. The slight downside is the new malloc()/free() overhead for each DTO, but that is negligible (*).
(*) on iMX8MM/MN and STM32MP1
Signed-off-by Marek Vasut <[email protected]>Cc Pantelis Antoniou <[email protected]>Cc Simon Glass <[email protected]>Cc Tom Rini <[email protected]>--- common/image-fit.c | 31 +++++++++++++++++++++++++++---- 1 file changed, 27 insertions(+), 4 deletions(-)
Quoted 3 lines
Quoted 1 line
Is this tested by the existing overlay test, or do we need something new?
Overlay test should be sufficient.
Quoted 23 lines · Marek Vasut
The current fitImage DTO implementation expects each fitImage image subnode containing DTO to have 'load' property, pointing somewhere into memory where the DTO will be loaded. The address in the 'load' property must be different then the base DT load address and there must be sufficient amount of space between those two addresses. Selecting and using such hard-coded addresses is fragile, error prone and difficult to port even across devices with the same SoC and different DRAM sizes.
The DTO cannot be applied in-place because
fdt_overlay_apply_verbose()modifies the DTO when applying it onto the base DT, so if the DTO was used in place within the fitImage, call tofdt_overlay_apply_verbose()would corrupt the fitImage.Instead of copying the DTO to a specific hard-coded load address, allocate a buffer, copy the DTO into that buffer, apply the DTO onto the base DT, and free the buffer.
The upside of this approach is that it is no longer necessary to select and hard-code specific DTO load address into the DTO. The slight downside is the new malloc()/free() overhead for each DTO, but that is negligible (*).
Quoted 7 lines
(*) on iMX8MM/MN and STM32MP1
Signed-off-by Marek Vasut <[email protected]>Cc Pantelis Antoniou <[email protected]>Cc Simon Glass <[email protected]>Cc Tom Rini <[email protected]>Reviewed-by Simon Glass <[email protected]>
Applied to u-boot/master, thanks!
Signature · 1 line
Tom