Skip to contentSkip to conversation

soundwire: stream: Fix test for DP prepare complete

PATCH Applied Richard Fitzgerald 3 participants 3 messages Jun 18, 2021 – Jun 20, 2021 SoundWire

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 soundwire: stream: Fix test for DP prepare complete

In sdw_prep_deprep_slave_ports(), after the wait_for_completion() the DP prepare status register is read. If this indicates that the port is now prepared, the code should continue with the port setup. It is irrelevant whether the wait_for_completion() timed out if the port is now ready.

The previous implementation would always fail if the wait_for_completion() timed out, even if the port was reporting successful prepare.

This patch also fixes a minor bug where the return from sdw_read() was not checked for error - any error code with LSBits clear could be misinterpreted as a successful port prepare.

Fixes 79df15b7d37c ("soundwire: Add helpers for ports operations")
---
 drivers/soundwire/stream.c | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)
drivers/soundwire/stream.c +6 -7
index 1eaedaaba094..1a18308f4ef4 100644
@@ -422,7 +422,6 @@ static int sdw_prep_deprep_slave_ports(struct sdw_bus *bus,
 	struct completion *port_ready;
 	struct sdw_dpn_prop *dpn_prop;
 	struct sdw_prepare_ch prep_ch;
-	unsigned int time_left;
 	bool intr = false;
 	int ret = 0, val;
 	u32 addr;
@@ -479,15 +478,15 @@ static int sdw_prep_deprep_slave_ports(struct sdw_bus *bus,
 
 		/* Wait for completion on port ready */
 		port_ready = &s_rt->slave->port_ready[prep_ch.num];
-		time_left = wait_for_completion_timeout(port_ready,
-				msecs_to_jiffies(dpn_prop->ch_prep_timeout));
+		wait_for_completion_timeout(port_ready,
+			msecs_to_jiffies(dpn_prop->ch_prep_timeout));
 
 		val = sdw_read(s_rt->slave, SDW_DPN_PREPARESTATUS(p_rt->num));
-		val &= p_rt->ch_mask;
-		if (!time_left || val) {
+		if ((val < 0) || (val & p_rt->ch_mask)) {
+			ret = (val < 0) ? val : -ETIMEDOUT;
 			dev_err(&s_rt->slave->dev,
-				"Chn prep failed for port:%d\n", prep_ch.num);
-			return -ETIMEDOUT;
+				"Chn prep failed for port %d: %d\n", prep_ch.num, ret);
+			return ret;
 		}
 	}
 
Signature · 1 line
2.20.1
Reviewed-by on v1 1/1
#1 lore raw
Quoted 10 lines · Richard Fitzgerald

In sdw_prep_deprep_slave_ports(), after the wait_for_completion() the DP prepare status register is read. If this indicates that the port is now prepared, the code should continue with the port setup. It is irrelevant whether the wait_for_completion() timed out if the port is now ready.

The previous implementation would always fail if the wait_for_completion() timed out, even if the port was reporting successful prepare.

Quoted 6 lines

This patch also fixes a minor bug where the return from sdw_read() was not checked for error - any error code with LSBits clear could be misinterpreted as a successful port prepare.

Fixes 79df15b7d37c ("soundwire: Add helpers for ports operations")

Looks good to me

Quoted 39 lines
---
 drivers/soundwire/stream.c | 13 ++++++-------
 1 file changed, 6 insertions(+), 7 deletions(-)
drivers/soundwire/stream.c +6 -7
index 1eaedaaba094..1a18308f4ef4 100644
@@ -422,7 +422,6 @@ static int sdw_prep_deprep_slave_ports(struct sdw_bus *bus,
 	struct completion *port_ready;
 	struct sdw_dpn_prop *dpn_prop;
 	struct sdw_prepare_ch prep_ch;
-	unsigned int time_left;
 	bool intr = false;
 	int ret = 0, val;
 	u32 addr;
@@ -479,15 +478,15 @@ static int sdw_prep_deprep_slave_ports(struct sdw_bus *bus,
 
 		/* Wait for completion on port ready */
 		port_ready = &s_rt->slave->port_ready[prep_ch.num];
-		time_left = wait_for_completion_timeout(port_ready,
-				msecs_to_jiffies(dpn_prop->ch_prep_timeout));
+		wait_for_completion_timeout(port_ready,
+			msecs_to_jiffies(dpn_prop->ch_prep_timeout));
 
 		val = sdw_read(s_rt->slave, SDW_DPN_PREPARESTATUS(p_rt->num));
-		val &= p_rt->ch_mask;
-		if (!time_left || val) {
+		if ((val < 0) || (val & p_rt->ch_mask)) {
+			ret = (val < 0) ? val : -ETIMEDOUT;
 			dev_err(&s_rt->slave->dev,
-				"Chn prep failed for port:%d\n", prep_ch.num);
-			return -ETIMEDOUT;
+				"Chn prep failed for port %d: %d\n", prep_ch.num, ret);
+			return ret;
 		}
 	}
 
maintainer Applied
#2 lore raw
In reply to Richard Fitzgerald
Quoted 6 lines · Richard Fitzgerald

In sdw_prep_deprep_slave_ports(), after the wait_for_completion() the DP prepare status register is read. If this indicates that the port is now prepared, the code should continue with the port setup. It is irrelevant whether the wait_for_completion() timed out if the port is now ready.

Quoted 7 lines

The previous implementation would always fail if the wait_for_completion() timed out, even if the port was reporting successful prepare.

This patch also fixes a minor bug where the return from sdw_read() was not checked for error - any error code with LSBits clear could be misinterpreted as a successful port prepare.

Applied, thanks

Signature · 1 line
~Vinod