drivers iio/adc: add driver for Texas Instruments TLA2528 adc
PATCH 1/1 drivers iio/adc: add driver for Texas Instruments TLA2528 adc
This adds a new driver for the TI TLA2528 ADC chip.
--- drivers/iio/adc/Kconfig | 10 ++ drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ti-tla2528.c | 246 +++++++++++++++++++++++++++++++++++ 3 files changed, 257 insertions(+) create mode 100644 drivers/iio/adc/ti-tla2528.c
drivers/iio/adc/Kconfig +10 -0
@@ -1178,6 +1178,16 @@ config TI_AM335X_ADC To compile this driver as a module, choose M here: the module will be called ti_am335x_adc. +config TI_TLA2528 + tristate "Texas Instruments TLA2528 ADC driver" + depends on I2C + help + Say yes here to build support for Texas Instruments TLA2528 + 12-Bit 8-Channel ADC. + + To compile this driver as a module, choose M here: the module will be + called ti-tla2528. + config TI_TLC4541 tristate "Texas Instruments TLC4541 ADC driver" depends on SPI
drivers/iio/adc/Makefile +1 -0
@@ -105,6 +105,7 @@ obj-$(CONFIG_TI_ADS8688) += ti-ads8688.o obj-$(CONFIG_TI_ADS124S08) += ti-ads124s08.o obj-$(CONFIG_TI_ADS131E08) += ti-ads131e08.o obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o +obj-$(CONFIG_TI_TLA2528) += ti-tla2528.o obj-$(CONFIG_TI_TLC4541) += ti-tlc4541.o obj-$(CONFIG_TI_TSC2046) += ti-tsc2046.o obj-$(CONFIG_TWL4030_MADC) += twl4030-madc.o
drivers/iio/adc/ti-tla2528.c new file +246 -0
246 lines not on this page · raw message
Signature · 1 line
2.25.1
Quoted 3 lines · Rodolfo Giometti
This adds a new driver for the TI TLA2528 ADC chip.
Hey,
The driver looks really good.
A general note: the drivers prefix in the patch title could be removed
A few more notes inline.
Quoted 86 lines
Signed-off-by Rodolfo Giometti <[email protected]>--- drivers/iio/adc/Kconfig | 10 ++ drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ti-tla2528.c | 246 +++++++++++++++++++++++++++++++++++ 3 files changed, 257 insertions(+) create mode 100644 drivers/iio/adc/ti-tla2528.cdrivers/iio/adc/Kconfig +10
-0@@ -1178,6 +1178,16 @@ config TI_AM335X_ADC To compile this driver as a module, choose M here: the module will be called ti_am335x_adc. +config TI_TLA2528 + tristate "Texas Instruments TLA2528 ADC driver" + depends on I2C + help + Say yes here to build support for Texas Instruments TLA2528 + 12-Bit 8-Channel ADC. + + To compile this driver as a module, choose M here: the module will be + called ti-tla2528. + config TI_TLC4541 tristate "Texas Instruments TLC4541 ADC driver" depends on SPIdrivers/iio/adc/Makefile +1
-0@@ -105,6 +105,7 @@ obj-$(CONFIG_TI_ADS8688) += ti-ads8688.o obj-$(CONFIG_TI_ADS124S08) += ti-ads124s08.o obj-$(CONFIG_TI_ADS131E08) += ti-ads131e08.o obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o +obj-$(CONFIG_TI_TLA2528) += ti-tla2528.o obj-$(CONFIG_TI_TLC4541) += ti-tlc4541.o obj-$(CONFIG_TI_TSC2046) += ti-tsc2046.o obj-$(CONFIG_TWL4030_MADC) += twl4030-madc.odrivers/iio/adc/ti-tla2528.c new file +39
-0@@ -0,0 +1,246 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* Driver for Texas Instruments TLA2528 ADC +* +* Copyright (C) 2020-2021 Rodolfo Giometti <[email protected]> +*/ + +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/delay.h> +#include <linux/regulator/consumer.h> +#include <linux/of.h> + +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> + +#define TLA2528_OP_READ_REG 0x10 +#define TLA2528_OP_WRITE_REG 0x08 + +#define TLA2528_GENERAL_CFG 0x01 +#define TLA2528_GENERAL_CFG_CNVST BIT(3) +#define TLA2528_DATA_CFG 0x02 +#define TLA2528_DATA_CFG_APPEND_STATUS BIT(4) +#define TLA2528_DATA_CFG_FIX_PAT BIT(7) +#define TLA2528_PIN_CFG 0x05 +#define TLA2528_SEQUENCE_CFG 0x10 +#define TLA2528_CHANNEL_SEL 0x11 + +struct tla2528_st { +struct i2c_client *client; +struct regulator *ref; + +u8 last_read_channel; +}; + +static s32 i2c_smbus_read_sample (const struct i2c_client *client) +{ +struct i2c_msg msg[1 ]; +u8 data[2 ];
drivers/iio/adc/ti-tla2528.c line 49
Quoted 10 lines
drivers/iio/adc/ti-tla2528.c new file +10
-0+int ret; + + msg[0 ].addr = client->addr; + msg[0 ].flags =I2C_M_RD ; + msg[0 ].buf = (u8 *) &data; + msg[0 ].len =2 ; + + ret =i2c_transfer (client->adapter, msg,1 ); + +return (ret <0 ) ? ret :le16_to_cpu (data[1 ] | (data[0 ] <<8 ));
this line does quite a lot of things;
one preferred way to do things would be:
if (ret < 0)
return ret;
return le16_to_cpu(data[1] | (data[0] << 8));
Quoted 106 lines
drivers/iio/adc/ti-tla2528.c new file +106
-0+} + +static s32 i2c_smbus_write_reg (const struct i2c_client *client,u8 reg,u8 val) +{ +struct i2c_msg msg[1 ]; +u8 cmd[3 ] = {TLA2528_OP_WRITE_REG , reg, val}; + + msg[0 ].addr = client->addr; + msg[0 ].flags =0 ; + msg[0 ].buf = cmd; + msg[0 ].len =3 ; + +return i2c_transfer (client->adapter, msg,1 ); +} + +static int tla2528_read (struct tla2528_st *st,u8 channel,int *val) +{ +struct i2c_client *client = st->client; +int ret; + +if (channel != st->last_read_channel) { + ret =i2c_smbus_write_reg (st->client, +TLA2528_CHANNEL_SEL , channel); +if (ret <0 ) +return ret; + + st->last_read_channel = channel; + } + +/* Read ADC data (2 bytes) */ + ret =i2c_smbus_read_sample (client); +if (ret <0 ) { +dev_err (&client->dev,"i2c_master_recv failed\n" ); +return ret; + } + *val = ret >>4 ; + +return 0 ; +} + +static int tla2528_read_raw (struct iio_dev *indio_dev, +struct iio_chan_spec const *chan, +int *val,int *val2,long mask) +{ +struct tla2528_st *st =iio_priv (indio_dev); +int ret; + +switch (mask) { +case IIO_CHAN_INFO_RAW : +mutex_lock (&indio_dev->mlock); + ret =tla2528_read (st, chan->channel, val); +mutex_unlock (&indio_dev->mlock); +if (ret <0 ) +return ret; + +return IIO_VAL_INT ; + +case IIO_CHAN_INFO_SCALE : + ret =regulator_get_voltage (st->ref); +if (ret <0 ) +return ret; + + *val = ret /1000 ; + *val2 =12 ; + +return IIO_VAL_FRACTIONAL_LOG2 ; + +default : +return -EINVAL ; + } +} + +#define TLA2528_CHAN (_chan, _name) { \ + .type = IIO_VOLTAGE, \ + .channel = (_chan), \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .datasheet_name = _name, \ + .indexed = 1, \ +} + +static const struct iio_chan_spec tla2528_channel[] = { +TLA2528_CHAN (0 ,"AIN0" ), +TLA2528_CHAN (1 ,"AIN1" ), +TLA2528_CHAN (2 ,"AIN2" ), +TLA2528_CHAN (3 ,"AIN3" ), +TLA2528_CHAN (4 ,"AIN4" ), +TLA2528_CHAN (5 ,"AIN5" ), +TLA2528_CHAN (6 ,"AIN6" ), +TLA2528_CHAN (7 ,"AIN7" ), +}; + +static const struct iio_info tla2528_info = { + .read_raw = tla2528_read_raw, +}; + +static int tla2528_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct iio_dev *indio_dev; +struct tla2528_st *st; +int ret; + +if (!i2c_check_functionality (client->adapter,I2C_FUNC_I2C | +I2C_FUNC_SMBUS_WRITE_BYTE )) +return -EOPNOTSUPP ;
drivers/iio/adc/ti-tla2528.c line 165
Quoted 10 lines
drivers/iio/adc/ti-tla2528.c new file +10
-0+ + indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*st)); +if (!indio_dev) +return -ENOMEM ; + + st =iio_priv (indio_dev); +i2c_set_clientdata (client, indio_dev); + st->client = client; + + indio_dev->dev.parent = &client->dev;
this assignment can be removed;
in newer kernels {devm_}iio_device_alloc() assigns the parent of the iio_dev object
Quoted 11 lines
drivers/iio/adc/ti-tla2528.c new file +11
-0+ indio_dev->name = id->name; + indio_dev->info = &tla2528_info; + indio_dev->modes =INDIO_DIRECT_MODE ; + indio_dev->channels = tla2528_channel; + indio_dev->num_channels =ARRAY_SIZE (tla2528_channel); + + st->ref =devm_regulator_get (&client->dev,"vref" ); +if (IS_ERR (st->ref)) +return PTR_ERR (st->ref); + + ret =regulator_enable (st->ref);
drivers/iio/adc/ti-tla2528.c line 186
Quoted 10 lines
drivers/iio/adc/ti-tla2528.c new file +10
-0+if (ret <0 ) +return ret; + +/* Set all inputs as analog */ + ret =i2c_smbus_write_reg (st->client,TLA2528_PIN_CFG ,0x00 ); +if (ret <0 ) + goto err_regulator_disable; + + ret =i2c_smbus_write_reg (st->client,TLA2528_DATA_CFG , +TLA2528_DATA_CFG_APPEND_STATUS );
minor: alignment of this line looks a little off
Quoted 33 lines
drivers/iio/adc/ti-tla2528.c new file +33
-0+if (ret <0 ) + goto err_regulator_disable; + +/* Set manual mode */ + ret =i2c_smbus_write_reg (st->client,TLA2528_SEQUENCE_CFG ,0x00 ); +if (ret <0 ) + goto err_regulator_disable; + +/* Init private data */ + st->last_read_channel = ~0 ; + + ret =iio_device_register (indio_dev); +if (ret <0 ) + goto err_regulator_disable; + +return 0 ; + +err_regulator_disable: +regulator_disable (st->ref); + +return ret; +} + +static int tla2528_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct tla2528_st *st =iio_priv (indio_dev); + +iio_device_unregister (indio_dev); +regulator_disable (st->ref); + +return 0 ; +}
drivers/iio/adc/ti-tla2528.c line 229
Quoted 10 lines
drivers/iio/adc/ti-tla2528.c new file +10
-0+ +static const struct i2c_device_id tla2528_id[] = { + {"tla2528" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, tla2528_id); + +static const struct of_device_id tla2528_of_match[] = { + { .compatible ="ti,tla2528" , }, + {},
nitpick: remove command from null-terminator;
drivers/iio/adc/ti-tla2528.c line 236
Quoted 7 lines
drivers/iio/adc/ti-tla2528.c new file +7
-0+}; +MODULE_DEVICE_TABLE (of, tla2528_of_match); + +static struct i2c_driver tla2528_driver = { + .driver = { + .name ="tla2528" , + .of_match_table =of_match_ptr (tla2528_of_match),
of_match_ptr() can be removed;
this can help the driver probe with ACPI later [if someone else wants to try it]
Quoted 13 lines
drivers/iio/adc/ti-tla2528.c new file +10
-1+ }, + .probe = tla2528_probe, + .remove = tla2528_remove, + .id_table = tla2528_id, +}; +module_i2c_driver (tla2528_driver); + +MODULE_AUTHOR ("Rodolfo Giometti <[email protected]>" ); +MODULE_DESCRIPTION ("Texas Instruments TLA2528 ADC driver" ); +MODULE_LICENSE ("GPL v2" ); --2.25.1