Skip to contentSkip to conversation

arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000

PATCH Applied Stephan Gerhold 3 participants 5 messages Sep 28, 2021

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000

While removing the size from the "reg" properties in pm8916.dtsi, commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties") mistakenly also removed the second register address for the rtc@6000 device. That one did not represent the size of the register region but actually the address of the second "alarm" register region of the rtc@6000 device.

Now there are "reg-names" for two "reg" elements, but there is actually only one "reg" listed.

Since the DT schema for "qcom,pm8941-rtc" only expects one "reg" element anyway, just drop the "reg-names" entirely to fix this.

Fixes bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
---
 arch/arm64/boot/dts/qcom/pm8916.dtsi | 1 -
 1 file changed, 1 deletion(-)
arch/arm64/boot/dts/qcom/pm8916.dtsi +0 -1
index f931cb0de231..42180f1b5dbb 100644
@@ -86,7 +86,6 @@ adc-chan@f {
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>;
-			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
Signature · 1 line
2.33.0
#1 lore raw

PATCH 2/3 arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection

At the moment, USB gadget mode on MSM8916 works only with an extcon device that reports the correct USB mode. This might be because the USB PHY needs to be configured appropriately.

Unfortunately there is currently no simple approach to get such an extcon device during early bring-up. The extcon device for USB VBUS (i.e. gadget/peripheral mode) is typically provided by the charging driver which is almost always very complex to port.

On pretty much all devices with PM8916, the USB VBUS is also connected to the PM8916 "USB_IN" pad, no matter if they use the linear charger integrated into PM8916 or not. The state of this pad can be checked with the "USBIN_VALID" interrupt of PM8916.

The "qcom,pm8941-misc" binding exists to expose an "usb_vbus" and/or "usb_id" interrupt from the PMIC as an extcon device.

Add a &pm8916_usbin node to pm8916.dtsi which can be used as simple extcon device for devices that are currently lacking a proper charger driver.

---
 arch/arm64/boot/dts/qcom/pm8916.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/qcom/pm8916.dtsi +8 -0
index 42180f1b5dbb..48c6c9cca53b 100644
@@ -41,6 +41,14 @@ watchdog {
 			};
 		};
 
+		pm8916_usbin: extcon@1300 {
+			compatible = "qcom,pm8941-misc";
+			reg = <0x1300>;
+			interrupts = <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "usb_vbus";
+			status = "disabled";
+		};
+
 		pm8916_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
Signature · 1 line
2.33.0
#2 lore raw

PATCH 3/3 arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon

In reply to Stephan Gerhold

At the moment, longcheer-l8150 is using a dummy extcon-usb-gpio device that permanently enables USB gadget mode. This workaround allows USB to work but is actually wrong and confusing. The "vbus-gpio" used there refers to an unused (floating) GPIO that is pulled up to make extcon-usb-gpio report USB gadget mode permanently.

Replace this with the new &pm8916_usbin extcon device that actually reports if an USB cable is attached or not. This allows the USB PHY to be turned off when there is no USB cable attached and is much cleaner overall.

Fixes 16e8e8072108 ("arm64: dts: qcom: Add device tree for Longcheer L8150")
---
 .../boot/dts/qcom/msm8916-longcheer-l8150.dts | 23 +++++--------------
 1 file changed, 6 insertions(+), 17 deletions(-)
arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts +6 -17
index 30716eb8fb2d..285102f0e04f 100644
@@ -30,14 +30,6 @@ wcnss_mem: wcnss@8b600000 {
 		};
 	};
 
-	// FIXME: Use extcon device provided by charger driver when available
-	usb_vbus: usb-vbus {
-		compatible = "linux,extcon-usb-gpio";
-		vbus-gpio = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb_vbus_default>;
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -215,6 +207,10 @@ &pm8916_resin {
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_usbin {
+	status = "okay";
+};
+
 &pm8916_vib {
 	status = "okay";
 };
@@ -244,11 +240,11 @@ &sdhc_2 {
 &usb {
 	status = "okay";
 	dr_mode = "peripheral";
-	extcon = <&usb_vbus>;
+	extcon = <&pm8916_usbin>;
 };
 
 &usb_hs_phy {
-	extcon = <&usb_vbus>;
+	extcon = <&pm8916_usbin>;
 };
 
 &smd_rpm_regulators {
@@ -410,11 +406,4 @@ tp_int_default: tp-int-default {
 		drive-strength = <2>;
 		bias-disable;
 	};
-
-	usb_vbus_default: usb-vbus-default {
-		pins = "gpio62";
-		function = "gpio";
-
-		bias-pull-up;
-	};
 };
Signature · 1 line
2.33.0
#3 lore raw
In reply to Stephan Gerhold
Quoted 8 lines · Stephan Gerhold

While removing the size from the "reg" properties in pm8916.dtsi, commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties") mistakenly also removed the second register address for the rtc@6000 device. That one did not represent the size of the register region but actually the address of the second "alarm" register region of the rtc@6000 device.

[...]

Applied, thanks!

[1/3] arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000

      commit: 483de2b44cd3a168458f8f9ff237e78a434729bc
[2/3] arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection
      commit: f5d7bca55425c8611e6cfa3f236d1f56031920e8
[3/3] arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon
      commit: b30cad26d8030bddeb0ee2373b6d4c1440ffb1a3

Best regards,

Signature · 1 line
Bjorn Andersson <[email protected]>
#4 lore raw
In reply to Stephan Gerhold
This series was applied to qcom/linux.git (refs/heads/for-next):

Hello:

This series was applied to qcom/linux.git (refs/heads/for-next):

Quoted 8 lines · On Tue, 28 Sep 2021 13:29:43 +0200 you wrote:

While removing the size from the "reg" properties in pm8916.dtsi, commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties") mistakenly also removed the second register address for the rtc@6000 device. That one did not represent the size of the register region but actually the address of the second "alarm" register region of the rtc@6000 device.

[...]

Here is the summary with links:
- [1/3] arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000

    https://git.kernel.org/qcom/c/483de2b44cd3
  - [2/3] arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection
    https://git.kernel.org/qcom/c/f5d7bca55425
  - [3/3] arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon
    https://git.kernel.org/qcom/c/b30cad26d803

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html