arm: dts: imx8mq: Add Kontron pitx-imx8m
Subsystems (3)
PATCH v6 1/2 arm: dts: imx8mq: Add Kontron pitx-imx8m
This adds the device tree for the Kontron pitx-imx8m Board. It is a copy of the device tree from the linux kernel sources.
---
v6:
- no change
v5:
- no change
v4:
- no change
v3:
- no change
v2:
- no change
arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mq-kontron-pitx-imx8m.dts | 613 +++++++++++++++++++++ 2 files changed, 615 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx8mq-kontron-pitx-imx8m.dts
arch/arm/dts/Makefile +2 -1
@@ -887,7 +887,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mq-phanbell.dtb \ imx8mp-evk.dtb \ imx8mp-phyboard-pollux-rdk.dtb \ - imx8mq-pico-pi.dtb + imx8mq-pico-pi.dtb \ + imx8mq-kontron-pitx-imx8m.dtb dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \ imxrt1020-evk.dtb
arch/arm/dts/imx8mq-kontron-pitx-imx8m.dts new file +613 -0
613 lines not on this page · raw message
Signature · 1 line
2.30.2
PATCH v6 2/2 board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
---
v6:
- increase PHY_ANEG_TIMEOUT
- spl: print boot source on startup
- spl: remove PMIC output
- enable CONFIG_CMD_TIME
v5:
- save env in eMMC boot partition 0
v4: update board integration
- migrate to IMX_CONFIG
- convert config options to Kconfig
- CONFIG_POWER_I2C
- CONFIG_SPL_POWER_I2C
- CONFIG_POWER_LEGACY
- CONFIG_SYS_LOAD_ADDR
- CONFIG_SYS_I2C_MXC
- CONFIG_SYS_I2C_LEGACY
- CONFIG_SYS_I2C_MXC_I2C1
- CONFIG_SYS_I2C_MXC_I2C2
- CONFIG_SYS_I2C_MXC_I2C3
- CONFIG_SYS_LOAD_ADDR
- CONFIG_MXC_GPIO
v3:
- enable EFI capsule support
- add update FIT image creation to binman config
- change env offset to fit into eMMC boot partition
v2:
- add support for 2/4GB variant
- enable config options
- CONFIG_CMD_GPT
- CONFIG_DM_ETH_PHY
- CONFIG_EFI_SET_TIME
- add pxefile_addr_r env variable
.../dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi | 163 ++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/kontron/pitx_imx8m/Kconfig | 15 + board/kontron/pitx_imx8m/MAINTAINERS | 7 + board/kontron/pitx_imx8m/Makefile | 8 + board/kontron/pitx_imx8m/imximage.cfg | 5 + board/kontron/pitx_imx8m/lpddr4_timing_2gb.c | 1853 +++++++++++++++++ board/kontron/pitx_imx8m/lpddr4_timing_4gb.c | 1853 +++++++++++++++++ board/kontron/pitx_imx8m/pitx_imx8m.c | 156 ++ board/kontron/pitx_imx8m/spl.c | 327 +++ configs/kontron_pitx_imx8m_defconfig | 87 + doc/board/kontron/index.rst | 1 + doc/board/kontron/pitx-imx8m.rst | 67 + include/configs/kontron_pitx_imx8m.h | 111 + 14 files changed, 4660 insertions(+) create mode 100644 arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi create mode 100644 board/kontron/pitx_imx8m/Kconfig create mode 100644 board/kontron/pitx_imx8m/MAINTAINERS create mode 100644 board/kontron/pitx_imx8m/Makefile create mode 100644 board/kontron/pitx_imx8m/imximage.cfg create mode 100644 board/kontron/pitx_imx8m/lpddr4_timing_2gb.c create mode 100644 board/kontron/pitx_imx8m/lpddr4_timing_4gb.c create mode 100644 board/kontron/pitx_imx8m/pitx_imx8m.c create mode 100644 board/kontron/pitx_imx8m/spl.c create mode 100644 configs/kontron_pitx_imx8m_defconfig create mode 100644 doc/board/kontron/pitx-imx8m.rst create mode 100644 include/configs/kontron_pitx_imx8m.h
arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi new file +163 -0
@@ -0,0 +1,163 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +#include <config.h> + +/ { + binman: binman { + multiple-images; + }; +}; + +&binman { + u-boot-spl-ddr { + filename = "u-boot-spl-ddr.bin"; + pad-byte = <0xff>; + align-size = <4>; + align = <4>; + + u-boot-spl { + align-end = <4>; + }; + + blob_1: blob-ext@1 { + filename = "lpddr4_pmu_train_1d_imem.bin"; + size = <0x8000>; + }; + + blob_2: blob-ext@2 { + filename = "lpddr4_pmu_train_1d_dmem.bin"; + size = <0x4000>; + }; + + blob_3: blob-ext@3 { + filename = "lpddr4_pmu_train_2d_imem.bin"; + size = <0x8000>; + }; + + blob_4: blob-ext@4 { + filename = "lpddr4_pmu_train_2d_dmem.bin"; + size = <0x4000>; + }; + }; + + spl { + filename = "spl.bin"; + + mkimage { + args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000"; + + blob { + filename = "u-boot-spl-ddr.bin"; + }; + }; + }; + + itb { + filename = "u-boot.itb"; + + fit { + description = "Configuration to load ATF before U-Boot"; + #address-cells = <1>; + fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>; + + images { + uboot { + description = "U-Boot (64-bit)"; + type = "standalone"; + arch = "arm64"; + compression = "none"; + load = <CONFIG_SYS_TEXT_BASE>; + + u-boot-nodtb { + }; + }; + + atf { + description = "ARM Trusted Firmware"; + type = "firmware"; + arch = "arm64"; + compression = "none"; + load = <0x910000>; + entry = <0x910000>; + + atf_blob: blob-ext { + filename = "bl31.bin"; + }; + }; + + fdt { + description = "imx8mq-kontron-pitx-imx8m.dtb"; + type = "flat_dt"; + compression = "none"; + + uboot_fdt_blob: blob-ext { + filename = "u-boot.dtb"; + }; + }; + }; + + configurations { + default = "conf"; + + conf { + description = "imx8mq-kontron-pitx-imx8m.dtb"; + firmware = "uboot"; + loadables = "atf"; + fdt = "fdt"; + }; + }; + }; + }; + + imx-boot { + filename = "flash.bin"; + pad-byte = <0x00>; + + spl: blob-ext@1 { + offset = <0x0>; + filename = "spl.bin"; + }; + + uboot: blob-ext@2 { + offset = <0x57c00>; + filename = "u-boot.itb"; + }; + }; + + u-boot-update { + filename = "firmware-update.itb"; + + fit { + description = "Configuration for firmware update file"; + + images { + flash-bin { + description = "U-Boot flash image"; + type = "firmware"; + os = "u-boot"; + arch = "arm"; + compress = "none"; + load = <0>; /* unused */ + + blob { + filename = "flash.bin"; + }; + + }; + }; + }; + }; +}; + +®_usdhc2_vmmc { + off-on-delay-us = <0>; +}; + +&usdhc1 { + mmc-hs400-1_8v; +}; + +&usdhc2 { + sd-uhs-sdr104; + sd-uhs-ddr50; +};
arch/arm/mach-imx/imx8m/Kconfig +7 -0
@@ -101,6 +101,12 @@ config TARGET_PICO_IMX8MQ select IMX8MQ select IMX8M_LPDDR4 +config TARGET_KONTRON_PITX_IMX8M + bool "Support Kontron pITX-imx8m" + select BINMAN + select IMX8MQ + select IMX8M_LPDDR4 + config TARGET_VERDIN_IMX8MM bool "Support Toradex Verdin iMX8M Mini module" select IMX8MM
@@ -150,6 +156,7 @@ source "board/freescale/imx8mn_evk/Kconfig" source "board/freescale/imx8mp_evk/Kconfig" source "board/gateworks/venice/Kconfig" source "board/google/imx8mq_phanbell/Kconfig" +source "board/kontron/pitx_imx8m/Kconfig" source "board/phytec/phycore_imx8mm/Kconfig" source "board/phytec/phycore_imx8mp/Kconfig" source "board/ronetix/imx8mq-cm/Kconfig"
board/kontron/pitx_imx8m/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_KONTRON_PITX_IMX8M + +config SYS_BOARD + default "pitx_imx8m" + +config SYS_VENDOR + default "kontron" + +config SYS_CONFIG_NAME + default "kontron_pitx_imx8m" + +config IMX_CONFIG + default "board/kontron/pitx_imx8m/imximage.cfg" + +endif
board/kontron/pitx_imx8m/MAINTAINERS new file +7 -0
@@ -0,0 +1,7 @@ +Kontron pITX-imx8m Board +M: Heiko Thiery <[email protected]> +S: Maintained +F: arch/arm/dts/imx8mq-kontron-pitx-imx8m* +F: board/kontron/pitx_imx8m/* +F: include/configs/kontron_pitx_imx8m.h +F: configs/kontron_pitx_imx8m_defconfig
board/kontron/pitx_imx8m/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y += pitx_imx8m.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing_2gb.o lpddr4_timing_4gb.o +endif
board/kontron/pitx_imx8m/imximage.cfg new file +5 -0
@@ -0,0 +1,5 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +BOOT_FROM sd +SIGNED_HDMI signed_hdmi_imx8m.bin +LOADER u-boot-spl-ddr.bin 0x7E1000
board/kontron/pitx_imx8m/lpddr4_timing_2gb.c new file +1853 -0
1,853 lines not on this page · raw message
board/kontron/pitx_imx8m/lpddr4_timing_4gb.c new file +1853 -0
930 lines not on this page · raw message
board/kontron/pitx_imx8m/pitx_imx8m.c new file +156 -0
156 lines not on this page · raw message
board/kontron/pitx_imx8m/spl.c new file +327 -0
327 lines not on this page · raw message
configs/kontron_pitx_imx8m_defconfig new file +87 -0
87 lines not on this page · raw message
doc/board/kontron/pitx-imx8m.rst new file +67 -0
67 lines not on this page · raw message
include/configs/kontron_pitx_imx8m.h new file +111 -0
111 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.30.2
Part of the diff is not shown here. View the raw message.
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional: blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000 ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory +
Could you take a look ?
Best regards,
Stefano Babic
Quoted 4,829 lines
Signed-off-by Heiko Thiery <[email protected]>---
v6:
- increasePHY_ANEG_TIMEOUT
- spl: print boot source on startup
- spl: remove PMIC output
- enableCONFIG_CMD_TIMEv5:
- save env in eMMC boot partition 0v4: update board integration
- migrate to
IMX_CONFIG
- convert config options toKconfig
-CONFIG_POWER_I2C
-CONFIG_SPL_POWER_I2C
-CONFIG_POWER_LEGACY
-CONFIG_SYS_LOAD_ADDR
-CONFIG_SYS_I2C_MXC
-CONFIG_SYS_I2C_LEGACY
-CONFIG_SYS_I2C_MXC_I2C1
-CONFIG_SYS_I2C_MXC_I2C2
-CONFIG_SYS_I2C_MXC_I2C3
-CONFIG_SYS_LOAD_ADDR
-CONFIG_MXC_GPIOv3:
- enable EFI capsule support
- add update FIT image creation to binman config
- change env offset to fit into eMMC boot partitionv2:
- add support for 2/4GB variant
- enable config options
-CONFIG_CMD_GPT
-CONFIG_DM_ETH_PHY
-CONFIG_EFI_SET_TIME
- addpxefile_addr_renv variable.../dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi | 163 ++ arch/arm/mach-imx/imx8m/Kconfig | 7 + board/kontron/pitx_imx8m/Kconfig | 15 + board/kontron/pitx_imx8m/MAINTAINERS | 7 + board/kontron/pitx_imx8m/Makefile | 8 + board/kontron/pitx_imx8m/imximage.cfg | 5 + board/kontron/pitx_imx8m/lpddr4_timing_2gb.c | 1853 +++++++++++++++++ board/kontron/pitx_imx8m/lpddr4_timing_4gb.c | 1853 +++++++++++++++++ board/kontron/pitx_imx8m/pitx_imx8m.c | 156 ++ board/kontron/pitx_imx8m/spl.c | 327 +++ configs/kontron_pitx_imx8m_defconfig | 87 + doc/board/kontron/index.rst | 1 + doc/board/kontron/pitx-imx8m.rst | 67 + include/configs/kontron_pitx_imx8m.h | 111 + 14 files changed, 4660 insertions(+)create mode 100644
arch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsicreate mode 100644 board/kontron/pitx_imx8m/Kconfig
create mode 100644 board/kontron/pitx_imx8m/MAINTAINERS create mode 100644 board/kontron/pitx_imx8m/Makefile create mode 100644 board/kontron/pitx_imx8m/imximage.cfg create mode 100644board/kontron/pitx_imx8m/lpddr4_timing_2gb.ccreate mode 100644board/kontron/pitx_imx8m/lpddr4_timing_4gb.ccreate mode 100644board/kontron/pitx_imx8m/pitx_imx8m.ccreate mode 100644board/kontron/pitx_imx8m/spl.c
create mode 100644 configs/kontron_pitx_imx8m_defconfig create mode 100644doc/board/kontron/pitx-imx8m.rst
create mode 100644include/configs/kontron_pitx_imx8m.harch/arm/dts/imx8mq-kontron-pitx-imx8m-u-boot.dtsi new file +163
-0@@ -0,0 +1,163 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +#include <config.h> + +/ { + binman: binman { + multiple-images; + }; +}; + +&binman { + u-boot-spl-ddr { + filename = "u-boot-spl-ddr.bin"; + pad-byte = <0xff>; + align-size = <4>; + align = <4>; + + u-boot-spl { + align-end = <4>; + }; + + blob_1: blob-ext@1 { + filename = "lpddr4_pmu_train_1d_imem.bin"; + size = <0x8000>; + }; + + blob_2: blob-ext@2 { + filename = "lpddr4_pmu_train_1d_dmem.bin"; + size = <0x4000>; + }; + + blob_3: blob-ext@3 { + filename = "lpddr4_pmu_train_2d_imem.bin"; + size = <0x8000>; + }; + + blob_4: blob-ext@4 { + filename = "lpddr4_pmu_train_2d_dmem.bin"; + size = <0x4000>; + }; + }; + + spl { + filename = "spl.bin"; + + mkimage { + args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000"; + + blob { + filename = "u-boot-spl-ddr.bin"; + }; + }; + }; + + itb { + filename = "u-boot.itb"; + + fit { + description = "Configuration to load ATF before U-Boot"; + #address-cells = <1>; + fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>; + + images { + uboot { + description = "U-Boot (64-bit)"; + type = "standalone"; + arch = "arm64"; + compression = "none"; + load = <CONFIG_SYS_TEXT_BASE>; + + u-boot-nodtb { + }; + }; + + atf { + description = "ARM Trusted Firmware"; + type = "firmware"; + arch = "arm64"; + compression = "none"; + load = <0x910000>; + entry = <0x910000>; + + atf_blob: blob-ext { + filename = "bl31.bin"; + }; + }; + + fdt { + description = "imx8mq-kontron-pitx-imx8m.dtb"; + type = "flat_dt"; + compression = "none"; + + uboot_fdt_blob: blob-ext { + filename = "u-boot.dtb"; + }; + }; + }; + + configurations { + default = "conf"; + + conf { + description = "imx8mq-kontron-pitx-imx8m.dtb"; + firmware = "uboot"; + loadables = "atf"; + fdt = "fdt"; + }; + }; + }; + }; + + imx-boot { + filename = "flash.bin"; + pad-byte = <0x00>; + + spl: blob-ext@1 { + offset = <0x0>; + filename = "spl.bin"; + }; + + uboot: blob-ext@2 { + offset = <0x57c00>; + filename = "u-boot.itb"; + }; + }; + + u-boot-update { + filename = "firmware-update.itb"; + + fit { + description = "Configuration for firmware update file"; + + images { + flash-bin { + description = "U-Boot flash image"; + type = "firmware"; + os = "u-boot"; + arch = "arm"; + compress = "none"; + load = <0>; /* unused */ + + blob { + filename = "flash.bin"; + }; + + }; + }; + }; + }; +}; + +®_usdhc2_vmmc { + off-on-delay-us = <0>; +}; + +&usdhc1 { + mmc-hs400-1_8v; +}; + +&usdhc2 { + sd-uhs-sdr104; + sd-uhs-ddr50; +};arch/arm/mach-imx/imx8m/Kconfig +7
-0@@ -101,6 +101,12 @@ config TARGET_PICO_IMX8MQ select IMX8MQ select IMX8M_LPDDR4 +config TARGET_KONTRON_PITX_IMX8M + bool "Support Kontron pITX-imx8m" + select BINMAN + select IMX8MQ + select IMX8M_LPDDR4 + config TARGET_VERDIN_IMX8MM bool "Support Toradex Verdin iMX8M Mini module" select IMX8MM@@ -150,6 +156,7 @@ source "board/freescale/imx8mn_evk/Kconfig" source "board/freescale/imx8mp_evk/Kconfig" source "board/gateworks/venice/Kconfig" source "board/google/imx8mq_phanbell/Kconfig" +source "board/kontron/pitx_imx8m/Kconfig" source "board/phytec/phycore_imx8mm/Kconfig" source "board/phytec/phycore_imx8mp/Kconfig" source "board/ronetix/imx8mq-cm/Kconfig"board/kontron/pitx_imx8m/Kconfig new file +15
-0@@ -0,0 +1,15 @@ +if TARGET_KONTRON_PITX_IMX8M + +config SYS_BOARD + default "pitx_imx8m" + +config SYS_VENDOR + default "kontron" + +config SYS_CONFIG_NAME + default "kontron_pitx_imx8m" + +config IMX_CONFIG + default "board/kontron/pitx_imx8m/imximage.cfg" + +endifboard/kontron/pitx_imx8m/MAINTAINERS new file +7
-0@@ -0,0 +1,7 @@ +Kontron pITX-imx8m Board +M: Heiko Thiery <[email protected]> +S: Maintained +F: arch/arm/dts/imx8mq-kontron-pitx-imx8m* +F: board/kontron/pitx_imx8m/* +F: include/configs/kontron_pitx_imx8m.h +F: configs/kontron_pitx_imx8m_defconfigboard/kontron/pitx_imx8m/Makefile new file +8
-0@@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0+ + +obj-y += pitx_imx8m.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing_2gb.o lpddr4_timing_4gb.o +endifboard/kontron/pitx_imx8m/imximage.cfg new file +5
-0@@ -0,0 +1,5 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ + +BOOT_FROM sd +SIGNED_HDMI signed_hdmi_imx8m.bin +LOADER u-boot-spl-ddr.bin 0x7E1000board/kontron/pitx_imx8m/lpddr4_timing_2gb.c new file +1853
-0@@ -0,0 +1,1853 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include <linux/kernel.h> +#include <asm/arch/ddr.h> +#include <asm/arch/lpddr4_define.h> + +static struct dram_cfg_param ddr_ddrc_cfg[] = { +/** Initialize DDRC registers **/ + {0x3d400304 ,0x1 }, + {0x3d400030 ,0x1 }, + {0x3d400000 ,0xa1080020 }, + {0x3d400028 ,0x0 }, + {0x3d400020 ,0x202 }, + {0x3d400024 ,0x3e800 }, + {0x3d400064 ,0x1800e0 }, + {0x3d4000d0 ,0xc003061c }, + {0x3d4000d4 ,0x9e0000 }, + {0x3d4000dc ,0xd4002d }, + {0x3d4000e0 ,0x310008 }, + {0x3d4000e8 ,0x66004a }, + {0x3d4000ec ,0x16004a }, + {0x3d400100 ,0x1a200624 }, + {0x3d400104 ,0x60636 }, + {0x3d40010c ,0xc0c000 }, + {0x3d400110 ,0x10040a10 }, + {0x3d400114 ,0x2040c0c }, + {0x3d400118 ,0x1010007 }, + {0x3d40011c ,0x401 }, + {0x3d400130 ,0x20600 }, + {0x3d400134 ,0xc100002 }, + {0x3d400138 ,0xe6 }, + {0x3d400144 ,0xa00050 }, + {0x3d400180 ,0xc3200018 }, + {0x3d400184 ,0x28061a8 }, + {0x3d400188 ,0x0 }, + {0x3d400190 ,0x497820a }, + {0x3d400194 ,0x80303 }, + {0x3d4001a0 ,0xe0400018 }, + {0x3d4001a4 ,0xdf00e4 }, + {0x3d4001a8 ,0x80000000 }, + {0x3d4001b0 ,0x11 }, + {0x3d4001b4 ,0x170a }, + {0x3d4001c0 ,0x1 }, + {0x3d4001c4 ,0x1 }, + {0x3d4000f4 ,0x639 }, + {0x3d400108 ,0x70e1617 }, + {0x3d400200 ,0x1f }, + {0x3d40020c ,0x0 }, + {0x3d400210 ,0x1f1f }, + {0x3d400204 ,0x80808 }, + {0x3d400214 ,0x7070707 }, + {0x3d400218 ,0x7070707 }, + {0x3d402020 ,0x0 }, + {0x3d402024 ,0x7d00 }, + {0x3d402050 ,0x20d040 }, + {0x3d402064 ,0x3001c }, + {0x3d4020dc ,0x840000 }, + {0x3d4020e0 ,0x310000 }, + {0x3d4020e8 ,0x66004a }, + {0x3d4020ec ,0x16004a }, + {0x3d402100 ,0xa040005 }, + {0x3d402104 ,0x30407 }, + {0x3d402108 ,0x203060b }, + {0x3d40210c ,0x505000 }, + {0x3d402110 ,0x2040202 }, + {0x3d402114 ,0x2030202 }, + {0x3d402118 ,0x1010004 }, + {0x3d40211c ,0x301 }, + {0x3d402130 ,0x20300 }, + {0x3d402134 ,0xa100002 }, + {0x3d402138 ,0x1d }, + {0x3d402144 ,0x14000a }, + {0x3d402180 ,0xc0640004 }, + {0x3d402190 ,0x3818200 }, + {0x3d402194 ,0x80303 }, + {0x3d4021b4 ,0x100 }, + {0x3d403020 ,0x0 }, + {0x3d403024 ,0x1f40 }, + {0x3d403050 ,0x20d040 }, + {0x3d403064 ,0x30007 }, + {0x3d4030dc ,0x840000 }, + {0x3d4030e0 ,0x310000 }, + {0x3d4030e8 ,0x66004a }, + {0x3d4030ec ,0x16004a }, + {0x3d403100 ,0xa010102 }, + {0x3d403104 ,0x30404 }, + {0x3d403108 ,0x203060b }, + {0x3d40310c ,0x505000 }, + {0x3d403110 ,0x2040202 }, + {0x3d403114 ,0x2030202 }, + {0x3d403118 ,0x1010004 }, + {0x3d40311c ,0x301 }, + {0x3d403130 ,0x20300 }, + {0x3d403134 ,0xa100002 }, + {0x3d403138 ,0x8 }, + {0x3d403144 ,0x50003 }, + {0x3d403180 ,0xc0190004 }, + {0x3d403190 ,0x3818200 }, + {0x3d403194 ,0x80303 }, + {0x3d4031b4 ,0x100 }, + {0x3d400244 ,0x0 }, + {0x3d400250 ,0x29001505 }, + {0x3d400254 ,0x2c }, + {0x3d40025c ,0x5900575b }, + {0x3d400264 ,0x90000096 }, + {0x3d40026c ,0x1000012c }, + {0x3d400300 ,0x16 }, + {0x3d400304 ,0x0 }, + {0x3d40030c ,0x0 }, + {0x3d400320 ,0x1 }, + {0x3d40036c ,0x11 }, + {0x3d400400 ,0x111 }, + {0x3d400404 ,0x10f3 }, + {0x3d400408 ,0x72ff }, + {0x3d400490 ,0x1 }, + {0x3d400494 ,0xe00 }, + {0x3d400498 ,0x62ffff }, + {0x3d40049c ,0xe00 }, + {0x3d4004a0 ,0xffff }, +}; + +/* PHY Initialize Configuration */ +static struct dram_cfg_param ddr_ddrphy_cfg[] = { + {0x100a0 ,0x2 }, + {0x100a1 ,0x3 }, + {0x100a2 ,0x0 }, + {0x100a3 ,0x1 }, + {0x100a4 ,0x5 }, + {0x100a5 ,0x7 }, + {0x100a6 ,0x6 }, + {0x100a7 ,0x4 }, + {0x110a0 ,0x2 }, + {0x110a1 ,0x1 }, + {0x110a2 ,0x3 }, + {0x110a3 ,0x0 }, + {0x110a4 ,0x6 }, + {0x110a5 ,0x7 }, + {0x110a6 ,0x4 }, + {0x110a7 ,0x5 }, + {0x120a0 ,0x4 }, + {0x120a1 ,0x5 }, + {0x120a2 ,0x7 }, + {0x120a3 ,0x6 }, + {0x120a4 ,0x1 }, + {0x120a5 ,0x3 }, + {0x120a6 ,0x2 }, + {0x120a7 ,0x0 }, + {0x130a0 ,0x4 }, + {0x130a1 ,0x5 }, + {0x130a2 ,0x7 }, + {0x130a3 ,0x6 }, + {0x130a4 ,0x2 }, + {0x130a5 ,0x1 }, + {0x130a6 ,0x0 }, + {0x130a7 ,0x3 }, + {0x1005f ,0x1ff }, + {0x1015f ,0x1ff }, + {0x1105f ,0x1ff }, + {0x1115f ,0x1ff }, + {0x1205f ,0x1ff }, + {0x1215f ,0x1ff }, + {0x1305f ,0x1ff }, + {0x1315f ,0x1ff }, + {0x11005f ,0x1ff }, + {0x11015f ,0x1ff }, + {0x11105f ,0x1ff }, + {0x11115f ,0x1ff }, + {0x11205f ,0x1ff }, + {0x11215f ,0x1ff }, + {0x11305f ,0x1ff }, + {0x11315f ,0x1ff }, + {0x21005f ,0x1ff }, + {0x21015f ,0x1ff }, + {0x21105f ,0x1ff }, + {0x21115f ,0x1ff }, + {0x21205f ,0x1ff }, + {0x21215f ,0x1ff }, + {0x21305f ,0x1ff }, + {0x21315f ,0x1ff }, + {0x55 ,0x1ff }, + {0x1055 ,0x1ff }, + {0x2055 ,0x1ff }, + {0x3055 ,0x1ff }, + {0x4055 ,0x1ff }, + {0x5055 ,0x1ff }, + {0x6055 ,0x1ff }, + {0x7055 ,0x1ff }, + {0x8055 ,0x1ff }, + {0x9055 ,0x1ff }, + {0x200c5 ,0x19 }, + {0x1200c5 ,0x7 }, + {0x2200c5 ,0x7 }, + {0x2002e ,0x2 }, + {0x12002e ,0x2 }, + {0x22002e ,0x2 }, + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + {0x20024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x120024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x220024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x20056 ,0x3 }, + {0x120056 ,0x3 }, + {0x220056 ,0x3 }, + {0x1004d ,0xe00 }, + {0x1014d ,0xe00 }, + {0x1104d ,0xe00 }, + {0x1114d ,0xe00 }, + {0x1204d ,0xe00 }, + {0x1214d ,0xe00 }, + {0x1304d ,0xe00 }, + {0x1314d ,0xe00 }, + {0x11004d ,0xe00 }, + {0x11014d ,0xe00 }, + {0x11104d ,0xe00 }, + {0x11114d ,0xe00 }, + {0x11204d ,0xe00 }, + {0x11214d ,0xe00 }, + {0x11304d ,0xe00 }, + {0x11314d ,0xe00 }, + {0x21004d ,0xe00 }, + {0x21014d ,0xe00 }, + {0x21104d ,0xe00 }, + {0x21114d ,0xe00 }, + {0x21204d ,0xe00 }, + {0x21214d ,0xe00 }, + {0x21304d ,0xe00 }, + {0x21314d ,0xe00 }, + {0x10049 ,0xeba }, + {0x10149 ,0xeba }, + {0x11049 ,0xeba }, + {0x11149 ,0xeba }, + {0x12049 ,0xeba }, + {0x12149 ,0xeba }, + {0x13049 ,0xeba }, + {0x13149 ,0xeba }, + {0x110049 ,0xeba }, + {0x110149 ,0xeba }, + {0x111049 ,0xeba }, + {0x111149 ,0xeba }, + {0x112049 ,0xeba }, + {0x112149 ,0xeba }, + {0x113049 ,0xeba }, + {0x113149 ,0xeba }, + {0x210049 ,0xeba }, + {0x210149 ,0xeba }, + {0x211049 ,0xeba }, + {0x211149 ,0xeba }, + {0x212049 ,0xeba }, + {0x212149 ,0xeba }, + {0x213049 ,0xeba }, + {0x213149 ,0xeba }, + {0x43 ,0x63 }, + {0x1043 ,0x63 }, + {0x2043 ,0x63 }, + {0x3043 ,0x63 }, + {0x4043 ,0x63 }, + {0x5043 ,0x63 }, + {0x6043 ,0x63 }, + {0x7043 ,0x63 }, + {0x8043 ,0x63 }, + {0x9043 ,0x63 }, + {0x20018 ,0x3 }, + {0x20075 ,0x4 }, + {0x20050 ,0x0 }, + {0x20008 ,0x320 }, + {0x120008 ,0x64 }, + {0x220008 ,0x19 }, + {0x20088 ,0x9 }, + {0x200b2 ,0xdc }, + {0x10043 ,0x5a1 }, + {0x10143 ,0x5a1 }, + {0x11043 ,0x5a1 }, + {0x11143 ,0x5a1 }, + {0x12043 ,0x5a1 }, + {0x12143 ,0x5a1 }, + {0x13043 ,0x5a1 }, + {0x13143 ,0x5a1 }, + {0x1200b2 ,0xdc }, + {0x110043 ,0x5a1 }, + {0x110143 ,0x5a1 }, + {0x111043 ,0x5a1 }, + {0x111143 ,0x5a1 }, + {0x112043 ,0x5a1 }, + {0x112143 ,0x5a1 }, + {0x113043 ,0x5a1 }, + {0x113143 ,0x5a1 }, + {0x2200b2 ,0xdc }, + {0x210043 ,0x5a1 }, + {0x210143 ,0x5a1 }, + {0x211043 ,0x5a1 }, + {0x211143 ,0x5a1 }, + {0x212043 ,0x5a1 }, + {0x212143 ,0x5a1 }, + {0x213043 ,0x5a1 }, + {0x213143 ,0x5a1 }, + {0x200fa ,0x1 }, + {0x1200fa ,0x1 }, + {0x2200fa ,0x1 }, + {0x20019 ,0x1 }, + {0x120019 ,0x1 }, + {0x220019 ,0x1 }, + {0x200f0 ,0x660 }, + {0x200f1 ,0x0 }, + {0x200f2 ,0x4444 }, + {0x200f3 ,0x8888 }, + {0x200f4 ,0x5665 }, + {0x200f5 ,0x0 }, + {0x200f6 ,0x0 }, + {0x200f7 ,0xf000 }, + {0x20025 ,0x0 }, + {0x2002d ,0x0 }, + {0x12002d ,0x0 }, + {0x22002d ,0x0 }, + {0x200c7 ,0x80 }, + {0x1200c7 ,0x80 }, + {0x2200c7 ,0x80 }, + {0x200ca ,0x106 }, + {0x1200ca ,0x106 }, + {0x2200ca ,0x106 }, + {0x20110 ,0x2 }, + {0x20111 ,0x3 }, + {0x20112 ,0x4 }, + {0x20113 ,0x5 }, + {0x20114 ,0x0 }, + {0x20115 ,0x1 }, +}; + +/* ddr phy trained csr */ +static struct dram_cfg_param ddr_ddrphy_trained_csr[] = { + {0x200b2 ,0x0 }, + {0x1200b2 ,0x0 }, + {0x2200b2 ,0x0 }, + {0x200cb ,0x0 }, + {0x10043 ,0x0 }, + {0x110043 ,0x0 }, + {0x210043 ,0x0 }, + {0x10143 ,0x0 }, + {0x110143 ,0x0 }, + {0x210143 ,0x0 }, + {0x11043 ,0x0 }, + {0x111043 ,0x0 }, + {0x211043 ,0x0 }, + {0x11143 ,0x0 }, + {0x111143 ,0x0 }, + {0x211143 ,0x0 }, + {0x12043 ,0x0 }, + {0x112043 ,0x0 }, + {0x212043 ,0x0 }, + {0x12143 ,0x0 }, + {0x112143 ,0x0 }, + {0x212143 ,0x0 }, + {0x13043 ,0x0 }, + {0x113043 ,0x0 }, + {0x213043 ,0x0 }, + {0x13143 ,0x0 }, + {0x113143 ,0x0 }, + {0x213143 ,0x0 }, + {0x80 ,0x0 }, + {0x100080 ,0x0 }, + {0x200080 ,0x0 }, + {0x1080 ,0x0 }, + {0x101080 ,0x0 }, + {0x201080 ,0x0 }, + {0x2080 ,0x0 }, + {0x102080 ,0x0 }, + {0x202080 ,0x0 }, + {0x3080 ,0x0 }, + {0x103080 ,0x0 }, + {0x203080 ,0x0 }, + {0x4080 ,0x0 }, + {0x104080 ,0x0 }, + {0x204080 ,0x0 }, + {0x5080 ,0x0 }, + {0x105080 ,0x0 }, + {0x205080 ,0x0 }, + {0x6080 ,0x0 }, + {0x106080 ,0x0 }, + {0x206080 ,0x0 }, + {0x7080 ,0x0 }, + {0x107080 ,0x0 }, + {0x207080 ,0x0 }, + {0x8080 ,0x0 }, + {0x108080 ,0x0 }, + {0x208080 ,0x0 }, + {0x9080 ,0x0 }, + {0x109080 ,0x0 }, + {0x209080 ,0x0 }, + {0x10080 ,0x0 }, + {0x110080 ,0x0 }, + {0x210080 ,0x0 }, + {0x10180 ,0x0 }, + {0x110180 ,0x0 }, + {0x210180 ,0x0 }, + {0x11080 ,0x0 }, + {0x111080 ,0x0 }, + {0x211080 ,0x0 }, + {0x11180 ,0x0 }, + {0x111180 ,0x0 }, + {0x211180 ,0x0 }, + {0x12080 ,0x0 }, + {0x112080 ,0x0 }, + {0x212080 ,0x0 }, + {0x12180 ,0x0 }, + {0x112180 ,0x0 }, + {0x212180 ,0x0 }, + {0x13080 ,0x0 }, + {0x113080 ,0x0 }, + {0x213080 ,0x0 }, + {0x13180 ,0x0 }, + {0x113180 ,0x0 }, + {0x213180 ,0x0 }, + {0x10081 ,0x0 }, + {0x110081 ,0x0 }, + {0x210081 ,0x0 }, + {0x10181 ,0x0 }, + {0x110181 ,0x0 }, + {0x210181 ,0x0 }, + {0x11081 ,0x0 }, + {0x111081 ,0x0 }, + {0x211081 ,0x0 }, + {0x11181 ,0x0 }, + {0x111181 ,0x0 }, + {0x211181 ,0x0 }, + {0x12081 ,0x0 }, + {0x112081 ,0x0 }, + {0x212081 ,0x0 }, + {0x12181 ,0x0 }, + {0x112181 ,0x0 }, + {0x212181 ,0x0 }, + {0x13081 ,0x0 }, + {0x113081 ,0x0 }, + {0x213081 ,0x0 }, + {0x13181 ,0x0 }, + {0x113181 ,0x0 }, + {0x213181 ,0x0 }, + {0x100d0 ,0x0 }, + {0x1100d0 ,0x0 }, + {0x2100d0 ,0x0 }, + {0x101d0 ,0x0 }, + {0x1101d0 ,0x0 }, + {0x2101d0 ,0x0 }, + {0x110d0 ,0x0 }, + {0x1110d0 ,0x0 }, + {0x2110d0 ,0x0 }, + {0x111d0 ,0x0 }, + {0x1111d0 ,0x0 }, + {0x2111d0 ,0x0 }, + {0x120d0 ,0x0 }, + {0x1120d0 ,0x0 }, + {0x2120d0 ,0x0 }, + {0x121d0 ,0x0 }, + {0x1121d0 ,0x0 }, + {0x2121d0 ,0x0 }, + {0x130d0 ,0x0 }, + {0x1130d0 ,0x0 }, + {0x2130d0 ,0x0 }, + {0x131d0 ,0x0 }, + {0x1131d0 ,0x0 }, + {0x2131d0 ,0x0 }, + {0x100d1 ,0x0 }, + {0x1100d1 ,0x0 }, + {0x2100d1 ,0x0 }, + {0x101d1 ,0x0 }, + {0x1101d1 ,0x0 }, + {0x2101d1 ,0x0 }, + {0x110d1 ,0x0 }, + {0x1110d1 ,0x0 }, + {0x2110d1 ,0x0 }, + {0x111d1 ,0x0 }, + {0x1111d1 ,0x0 }, + {0x2111d1 ,0x0 }, + {0x120d1 ,0x0 }, + {0x1120d1 ,0x0 }, + {0x2120d1 ,0x0 }, + {0x121d1 ,0x0 }, + {0x1121d1 ,0x0 }, + {0x2121d1 ,0x0 }, + {0x130d1 ,0x0 }, + {0x1130d1 ,0x0 }, + {0x2130d1 ,0x0 }, + {0x131d1 ,0x0 }, + {0x1131d1 ,0x0 }, + {0x2131d1 ,0x0 }, + {0x10068 ,0x0 }, + {0x10168 ,0x0 }, + {0x10268 ,0x0 }, + {0x10368 ,0x0 }, + {0x10468 ,0x0 }, + {0x10568 ,0x0 }, + {0x10668 ,0x0 }, + {0x10768 ,0x0 }, + {0x10868 ,0x0 }, + {0x11068 ,0x0 }, + {0x11168 ,0x0 }, + {0x11268 ,0x0 }, + {0x11368 ,0x0 }, + {0x11468 ,0x0 }, + {0x11568 ,0x0 }, + {0x11668 ,0x0 }, + {0x11768 ,0x0 }, + {0x11868 ,0x0 }, + {0x12068 ,0x0 }, + {0x12168 ,0x0 }, + {0x12268 ,0x0 }, + {0x12368 ,0x0 }, + {0x12468 ,0x0 }, + {0x12568 ,0x0 }, + {0x12668 ,0x0 }, + {0x12768 ,0x0 }, + {0x12868 ,0x0 }, + {0x13068 ,0x0 }, + {0x13168 ,0x0 }, + {0x13268 ,0x0 }, + {0x13368 ,0x0 }, + {0x13468 ,0x0 }, + {0x13568 ,0x0 }, + {0x13668 ,0x0 }, + {0x13768 ,0x0 }, + {0x13868 ,0x0 }, + {0x10069 ,0x0 }, + {0x10169 ,0x0 }, + {0x10269 ,0x0 }, + {0x10369 ,0x0 }, + {0x10469 ,0x0 }, + {0x10569 ,0x0 }, + {0x10669 ,0x0 }, + {0x10769 ,0x0 }, + {0x10869 ,0x0 }, + {0x11069 ,0x0 }, + {0x11169 ,0x0 }, + {0x11269 ,0x0 }, + {0x11369 ,0x0 }, + {0x11469 ,0x0 }, + {0x11569 ,0x0 }, + {0x11669 ,0x0 }, + {0x11769 ,0x0 }, + {0x11869 ,0x0 }, + {0x12069 ,0x0 }, + {0x12169 ,0x0 }, + {0x12269 ,0x0 }, + {0x12369 ,0x0 }, + {0x12469 ,0x0 }, + {0x12569 ,0x0 }, + {0x12669 ,0x0 }, + {0x12769 ,0x0 }, + {0x12869 ,0x0 }, + {0x13069 ,0x0 }, + {0x13169 ,0x0 }, + {0x13269 ,0x0 }, + {0x13369 ,0x0 }, + {0x13469 ,0x0 }, + {0x13569 ,0x0 }, + {0x13669 ,0x0 }, + {0x13769 ,0x0 }, + {0x13869 ,0x0 }, + {0x1008c ,0x0 }, + {0x11008c ,0x0 }, + {0x21008c ,0x0 }, + {0x1018c ,0x0 }, + {0x11018c ,0x0 }, + {0x21018c ,0x0 }, + {0x1108c ,0x0 }, + {0x11108c ,0x0 }, + {0x21108c ,0x0 }, + {0x1118c ,0x0 }, + {0x11118c ,0x0 }, + {0x21118c ,0x0 }, + {0x1208c ,0x0 }, + {0x11208c ,0x0 }, + {0x21208c ,0x0 }, + {0x1218c ,0x0 }, + {0x11218c ,0x0 }, + {0x21218c ,0x0 }, + {0x1308c ,0x0 }, + {0x11308c ,0x0 }, + {0x21308c ,0x0 }, + {0x1318c ,0x0 }, + {0x11318c ,0x0 }, + {0x21318c ,0x0 }, + {0x1008d ,0x0 }, + {0x11008d ,0x0 }, + {0x21008d ,0x0 }, + {0x1018d ,0x0 }, + {0x11018d ,0x0 }, + {0x21018d ,0x0 }, + {0x1108d ,0x0 }, + {0x11108d ,0x0 }, + {0x21108d ,0x0 }, + {0x1118d ,0x0 }, + {0x11118d ,0x0 }, + {0x21118d ,0x0 }, + {0x1208d ,0x0 }, + {0x11208d ,0x0 }, + {0x21208d ,0x0 }, + {0x1218d ,0x0 }, + {0x11218d ,0x0 }, + {0x21218d ,0x0 }, + {0x1308d ,0x0 }, + {0x11308d ,0x0 }, + {0x21308d ,0x0 }, + {0x1318d ,0x0 }, + {0x11318d ,0x0 }, + {0x21318d ,0x0 }, + {0x100c0 ,0x0 }, + {0x1100c0 ,0x0 }, + {0x2100c0 ,0x0 }, + {0x101c0 ,0x0 }, + {0x1101c0 ,0x0 }, + {0x2101c0 ,0x0 }, + {0x102c0 ,0x0 }, + {0x1102c0 ,0x0 }, + {0x2102c0 ,0x0 }, + {0x103c0 ,0x0 }, + {0x1103c0 ,0x0 }, + {0x2103c0 ,0x0 }, + {0x104c0 ,0x0 }, + {0x1104c0 ,0x0 }, + {0x2104c0 ,0x0 }, + {0x105c0 ,0x0 }, + {0x1105c0 ,0x0 }, + {0x2105c0 ,0x0 }, + {0x106c0 ,0x0 }, + {0x1106c0 ,0x0 }, + {0x2106c0 ,0x0 }, + {0x107c0 ,0x0 }, + {0x1107c0 ,0x0 }, + {0x2107c0 ,0x0 }, + {0x108c0 ,0x0 }, + {0x1108c0 ,0x0 }, + {0x2108c0 ,0x0 }, + {0x110c0 ,0x0 }, + {0x1110c0 ,0x0 }, + {0x2110c0 ,0x0 }, + {0x111c0 ,0x0 }, + {0x1111c0 ,0x0 }, + {0x2111c0 ,0x0 }, + {0x112c0 ,0x0 }, + {0x1112c0 ,0x0 }, + {0x2112c0 ,0x0 }, + {0x113c0 ,0x0 }, + {0x1113c0 ,0x0 }, + {0x2113c0 ,0x0 }, + {0x114c0 ,0x0 }, + {0x1114c0 ,0x0 }, + {0x2114c0 ,0x0 }, + {0x115c0 ,0x0 }, + {0x1115c0 ,0x0 }, + {0x2115c0 ,0x0 }, + {0x116c0 ,0x0 }, + {0x1116c0 ,0x0 }, + {0x2116c0 ,0x0 }, + {0x117c0 ,0x0 }, + {0x1117c0 ,0x0 }, + {0x2117c0 ,0x0 }, + {0x118c0 ,0x0 }, + {0x1118c0 ,0x0 }, + {0x2118c0 ,0x0 }, + {0x120c0 ,0x0 }, + {0x1120c0 ,0x0 }, + {0x2120c0 ,0x0 }, + {0x121c0 ,0x0 }, + {0x1121c0 ,0x0 }, + {0x2121c0 ,0x0 }, + {0x122c0 ,0x0 }, + {0x1122c0 ,0x0 }, + {0x2122c0 ,0x0 }, + {0x123c0 ,0x0 }, + {0x1123c0 ,0x0 }, + {0x2123c0 ,0x0 }, + {0x124c0 ,0x0 }, + {0x1124c0 ,0x0 }, + {0x2124c0 ,0x0 }, + {0x125c0 ,0x0 }, + {0x1125c0 ,0x0 }, + {0x2125c0 ,0x0 }, + {0x126c0 ,0x0 }, + {0x1126c0 ,0x0 }, + {0x2126c0 ,0x0 }, + {0x127c0 ,0x0 }, + {0x1127c0 ,0x0 }, + {0x2127c0 ,0x0 }, + {0x128c0 ,0x0 }, + {0x1128c0 ,0x0 }, + {0x2128c0 ,0x0 }, + {0x130c0 ,0x0 }, + {0x1130c0 ,0x0 }, + {0x2130c0 ,0x0 }, + {0x131c0 ,0x0 }, + {0x1131c0 ,0x0 }, + {0x2131c0 ,0x0 }, + {0x132c0 ,0x0 }, + {0x1132c0 ,0x0 }, + {0x2132c0 ,0x0 }, + {0x133c0 ,0x0 }, + {0x1133c0 ,0x0 }, + {0x2133c0 ,0x0 }, + {0x134c0 ,0x0 }, + {0x1134c0 ,0x0 }, + {0x2134c0 ,0x0 }, + {0x135c0 ,0x0 }, + {0x1135c0 ,0x0 }, + {0x2135c0 ,0x0 }, + {0x136c0 ,0x0 }, + {0x1136c0 ,0x0 }, + {0x2136c0 ,0x0 }, + {0x137c0 ,0x0 }, + {0x1137c0 ,0x0 }, + {0x2137c0 ,0x0 }, + {0x138c0 ,0x0 }, + {0x1138c0 ,0x0 }, + {0x2138c0 ,0x0 }, + {0x100c1 ,0x0 }, + {0x1100c1 ,0x0 }, + {0x2100c1 ,0x0 }, + {0x101c1 ,0x0 }, + {0x1101c1 ,0x0 }, + {0x2101c1 ,0x0 }, + {0x102c1 ,0x0 }, + {0x1102c1 ,0x0 }, + {0x2102c1 ,0x0 }, + {0x103c1 ,0x0 }, + {0x1103c1 ,0x0 }, + {0x2103c1 ,0x0 }, + {0x104c1 ,0x0 }, + {0x1104c1 ,0x0 }, + {0x2104c1 ,0x0 }, + {0x105c1 ,0x0 }, + {0x1105c1 ,0x0 }, + {0x2105c1 ,0x0 }, + {0x106c1 ,0x0 }, + {0x1106c1 ,0x0 }, + {0x2106c1 ,0x0 }, + {0x107c1 ,0x0 }, + {0x1107c1 ,0x0 }, + {0x2107c1 ,0x0 }, + {0x108c1 ,0x0 }, + {0x1108c1 ,0x0 }, + {0x2108c1 ,0x0 }, + {0x110c1 ,0x0 }, + {0x1110c1 ,0x0 }, + {0x2110c1 ,0x0 }, + {0x111c1 ,0x0 }, + {0x1111c1 ,0x0 }, + {0x2111c1 ,0x0 }, + {0x112c1 ,0x0 }, + {0x1112c1 ,0x0 }, + {0x2112c1 ,0x0 }, + {0x113c1 ,0x0 }, + {0x1113c1 ,0x0 }, + {0x2113c1 ,0x0 }, + {0x114c1 ,0x0 }, + {0x1114c1 ,0x0 }, + {0x2114c1 ,0x0 }, + {0x115c1 ,0x0 }, + {0x1115c1 ,0x0 }, + {0x2115c1 ,0x0 }, + {0x116c1 ,0x0 }, + {0x1116c1 ,0x0 }, + {0x2116c1 ,0x0 }, + {0x117c1 ,0x0 }, + {0x1117c1 ,0x0 }, + {0x2117c1 ,0x0 }, + {0x118c1 ,0x0 }, + {0x1118c1 ,0x0 }, + {0x2118c1 ,0x0 }, + {0x120c1 ,0x0 }, + {0x1120c1 ,0x0 }, + {0x2120c1 ,0x0 }, + {0x121c1 ,0x0 }, + {0x1121c1 ,0x0 }, + {0x2121c1 ,0x0 }, + {0x122c1 ,0x0 }, + {0x1122c1 ,0x0 }, + {0x2122c1 ,0x0 }, + {0x123c1 ,0x0 }, + {0x1123c1 ,0x0 }, + {0x2123c1 ,0x0 }, + {0x124c1 ,0x0 }, + {0x1124c1 ,0x0 }, + {0x2124c1 ,0x0 }, + {0x125c1 ,0x0 }, + {0x1125c1 ,0x0 }, + {0x2125c1 ,0x0 }, + {0x126c1 ,0x0 }, + {0x1126c1 ,0x0 }, + {0x2126c1 ,0x0 }, + {0x127c1 ,0x0 }, + {0x1127c1 ,0x0 }, + {0x2127c1 ,0x0 }, + {0x128c1 ,0x0 }, + {0x1128c1 ,0x0 }, + {0x2128c1 ,0x0 }, + {0x130c1 ,0x0 }, + {0x1130c1 ,0x0 }, + {0x2130c1 ,0x0 }, + {0x131c1 ,0x0 }, + {0x1131c1 ,0x0 }, + {0x2131c1 ,0x0 }, + {0x132c1 ,0x0 }, + {0x1132c1 ,0x0 }, + {0x2132c1 ,0x0 }, + {0x133c1 ,0x0 }, + {0x1133c1 ,0x0 }, + {0x2133c1 ,0x0 }, + {0x134c1 ,0x0 }, + {0x1134c1 ,0x0 }, + {0x2134c1 ,0x0 }, + {0x135c1 ,0x0 }, + {0x1135c1 ,0x0 }, + {0x2135c1 ,0x0 }, + {0x136c1 ,0x0 }, + {0x1136c1 ,0x0 }, + {0x2136c1 ,0x0 }, + {0x137c1 ,0x0 }, + {0x1137c1 ,0x0 }, + {0x2137c1 ,0x0 }, + {0x138c1 ,0x0 }, + {0x1138c1 ,0x0 }, + {0x2138c1 ,0x0 }, + {0x10020 ,0x0 }, + {0x110020 ,0x0 }, + {0x210020 ,0x0 }, + {0x11020 ,0x0 }, + {0x111020 ,0x0 }, + {0x211020 ,0x0 }, + {0x12020 ,0x0 }, + {0x112020 ,0x0 }, + {0x212020 ,0x0 }, + {0x13020 ,0x0 }, + {0x113020 ,0x0 }, + {0x213020 ,0x0 }, + {0x20072 ,0x0 }, + {0x20073 ,0x0 }, + {0x20074 ,0x0 }, + {0x100aa ,0x0 }, + {0x110aa ,0x0 }, + {0x120aa ,0x0 }, + {0x130aa ,0x0 }, + {0x20010 ,0x0 }, + {0x120010 ,0x0 }, + {0x220010 ,0x0 }, + {0x20011 ,0x0 }, + {0x120011 ,0x0 }, + {0x220011 ,0x0 }, + {0x100ae ,0x0 }, + {0x1100ae ,0x0 }, + {0x2100ae ,0x0 }, + {0x100af ,0x0 }, + {0x1100af ,0x0 }, + {0x2100af ,0x0 }, + {0x110ae ,0x0 }, + {0x1110ae ,0x0 }, + {0x2110ae ,0x0 }, + {0x110af ,0x0 }, + {0x1110af ,0x0 }, + {0x2110af ,0x0 }, + {0x120ae ,0x0 }, + {0x1120ae ,0x0 }, + {0x2120ae ,0x0 }, + {0x120af ,0x0 }, + {0x1120af ,0x0 }, + {0x2120af ,0x0 }, + {0x130ae ,0x0 }, + {0x1130ae ,0x0 }, + {0x2130ae ,0x0 }, + {0x130af ,0x0 }, + {0x1130af ,0x0 }, + {0x2130af ,0x0 }, + {0x20020 ,0x0 }, + {0x120020 ,0x0 }, + {0x220020 ,0x0 }, + {0x100a0 ,0x0 }, + {0x100a1 ,0x0 }, + {0x100a2 ,0x0 }, + {0x100a3 ,0x0 }, + {0x100a4 ,0x0 }, + {0x100a5 ,0x0 }, + {0x100a6 ,0x0 }, + {0x100a7 ,0x0 }, + {0x110a0 ,0x0 }, + {0x110a1 ,0x0 }, + {0x110a2 ,0x0 }, + {0x110a3 ,0x0 }, + {0x110a4 ,0x0 }, + {0x110a5 ,0x0 }, + {0x110a6 ,0x0 }, + {0x110a7 ,0x0 }, + {0x120a0 ,0x0 }, + {0x120a1 ,0x0 }, + {0x120a2 ,0x0 }, + {0x120a3 ,0x0 }, + {0x120a4 ,0x0 }, + {0x120a5 ,0x0 }, + {0x120a6 ,0x0 }, + {0x120a7 ,0x0 }, + {0x130a0 ,0x0 }, + {0x130a1 ,0x0 }, + {0x130a2 ,0x0 }, + {0x130a3 ,0x0 }, + {0x130a4 ,0x0 }, + {0x130a5 ,0x0 }, + {0x130a6 ,0x0 }, + {0x130a7 ,0x0 }, + {0x2007c ,0x0 }, + {0x12007c ,0x0 }, + {0x22007c ,0x0 }, + {0x2007d ,0x0 }, + {0x12007d ,0x0 }, + {0x22007d ,0x0 }, + {0x400fd ,0x0 }, + {0x400c0 ,0x0 }, + {0x90201 ,0x0 }, + {0x190201 ,0x0 }, + {0x290201 ,0x0 }, + {0x90202 ,0x0 }, + {0x190202 ,0x0 }, + {0x290202 ,0x0 }, + {0x90203 ,0x0 }, + {0x190203 ,0x0 }, + {0x290203 ,0x0 }, + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + {0x90205 ,0x0 }, + {0x190205 ,0x0 }, + {0x290205 ,0x0 }, + {0x90206 ,0x0 }, + {0x190206 ,0x0 }, + {0x290206 ,0x0 }, + {0x90207 ,0x0 }, + {0x190207 ,0x0 }, + {0x290207 ,0x0 }, + {0x90208 ,0x0 }, + {0x190208 ,0x0 }, + {0x290208 ,0x0 }, + {0x10062 ,0x0 }, + {0x10162 ,0x0 }, + {0x10262 ,0x0 }, + {0x10362 ,0x0 }, + {0x10462 ,0x0 }, + {0x10562 ,0x0 }, + {0x10662 ,0x0 }, + {0x10762 ,0x0 }, + {0x10862 ,0x0 }, + {0x11062 ,0x0 }, + {0x11162 ,0x0 }, + {0x11262 ,0x0 }, + {0x11362 ,0x0 }, + {0x11462 ,0x0 }, + {0x11562 ,0x0 }, + {0x11662 ,0x0 }, + {0x11762 ,0x0 }, + {0x11862 ,0x0 }, + {0x12062 ,0x0 }, + {0x12162 ,0x0 }, + {0x12262 ,0x0 }, + {0x12362 ,0x0 }, + {0x12462 ,0x0 }, + {0x12562 ,0x0 }, + {0x12662 ,0x0 }, + {0x12762 ,0x0 }, + {0x12862 ,0x0 }, + {0x13062 ,0x0 }, + {0x13162 ,0x0 }, + {0x13262 ,0x0 }, + {0x13362 ,0x0 }, + {0x13462 ,0x0 }, + {0x13562 ,0x0 }, + {0x13662 ,0x0 }, + {0x13762 ,0x0 }, + {0x13862 ,0x0 }, + {0x20077 ,0x0 }, + {0x10001 ,0x0 }, + {0x11001 ,0x0 }, + {0x12001 ,0x0 }, + {0x13001 ,0x0 }, + {0x10040 ,0x0 }, + {0x10140 ,0x0 }, + {0x10240 ,0x0 }, + {0x10340 ,0x0 }, + {0x10440 ,0x0 }, + {0x10540 ,0x0 }, + {0x10640 ,0x0 }, + {0x10740 ,0x0 }, + {0x10840 ,0x0 }, + {0x10030 ,0x0 }, + {0x10130 ,0x0 }, + {0x10230 ,0x0 }, + {0x10330 ,0x0 }, + {0x10430 ,0x0 }, + {0x10530 ,0x0 }, + {0x10630 ,0x0 }, + {0x10730 ,0x0 }, + {0x10830 ,0x0 }, + {0x11040 ,0x0 }, + {0x11140 ,0x0 }, + {0x11240 ,0x0 }, + {0x11340 ,0x0 }, + {0x11440 ,0x0 }, + {0x11540 ,0x0 }, + {0x11640 ,0x0 }, + {0x11740 ,0x0 }, + {0x11840 ,0x0 }, + {0x11030 ,0x0 }, + {0x11130 ,0x0 }, + {0x11230 ,0x0 }, + {0x11330 ,0x0 }, + {0x11430 ,0x0 }, + {0x11530 ,0x0 }, + {0x11630 ,0x0 }, + {0x11730 ,0x0 }, + {0x11830 ,0x0 }, + {0x12040 ,0x0 }, + {0x12140 ,0x0 }, + {0x12240 ,0x0 }, + {0x12340 ,0x0 }, + {0x12440 ,0x0 }, + {0x12540 ,0x0 }, + {0x12640 ,0x0 }, + {0x12740 ,0x0 }, + {0x12840 ,0x0 }, + {0x12030 ,0x0 }, + {0x12130 ,0x0 }, + {0x12230 ,0x0 }, + {0x12330 ,0x0 }, + {0x12430 ,0x0 }, + {0x12530 ,0x0 }, + {0x12630 ,0x0 }, + {0x12730 ,0x0 }, + {0x12830 ,0x0 }, + {0x13040 ,0x0 }, + {0x13140 ,0x0 }, + {0x13240 ,0x0 }, + {0x13340 ,0x0 }, + {0x13440 ,0x0 }, + {0x13540 ,0x0 }, + {0x13640 ,0x0 }, + {0x13740 ,0x0 }, + {0x13840 ,0x0 }, + {0x13030 ,0x0 }, + {0x13130 ,0x0 }, + {0x13230 ,0x0 }, + {0x13330 ,0x0 }, + {0x13430 ,0x0 }, + {0x13530 ,0x0 }, + {0x13630 ,0x0 }, + {0x13730 ,0x0 }, + {0x13830 ,0x0 }, +}; + +/* P0 message block paremeter for training firmware */ +static struct dram_cfg_param ddr_fsp0_cfg[] = { + {0xd0000 ,0x0 }, + {0x54003 ,0xc80 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x131f }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x54012 ,0x110 }, + {0x54019 ,0x2dd4 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4a66 }, + {0x5401c ,0x4a08 }, + {0x5401e ,0x16 }, + {0x5401f ,0x2dd4 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4a66 }, + {0x54022 ,0x4a08 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0xd400 }, + {0x54033 ,0x312d }, + {0x54034 ,0x6600 }, + {0x54035 ,0x84a }, + {0x54036 ,0x4a }, + {0x54037 ,0x1600 }, + {0x54038 ,0xd400 }, + {0x54039 ,0x312d }, + {0x5403a ,0x6600 }, + {0x5403b ,0x84a }, + {0x5403c ,0x4a }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* P1 message block paremeter for training firmware */ +static struct dram_cfg_param ddr_fsp1_cfg[] = { + {0xd0000 ,0x0 }, + {0x54002 ,0x101 }, + {0x54003 ,0x190 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x121f }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x54012 ,0x110 }, + {0x54019 ,0x84 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4a66 }, + {0x5401c ,0x4a08 }, + {0x5401e ,0x16 }, + {0x5401f ,0x84 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4a66 }, + {0x54022 ,0x4a08 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0x8400 }, + {0x54033 ,0x3100 }, + {0x54034 ,0x6600 }, + {0x54035 ,0x84a }, + {0x54036 ,0x4a }, + {0x54037 ,0x1600 }, + {0x54038 ,0x8400 }, + {0x54039 ,0x3100 }, + {0x5403a ,0x6600 }, + {0x5403b ,0x84a }, + {0x5403c ,0x4a }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* P2 message block paremeter for training firmware */ +static struct dram_cfg_param ddr_fsp2_cfg[] = { + {0xd0000 ,0x0 }, + {0x54002 ,0x102 }, + {0x54003 ,0x64 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x121f }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x54012 ,0x110 }, + {0x54019 ,0x84 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4a66 }, + {0x5401c ,0x4a08 }, + {0x5401e ,0x16 }, + {0x5401f ,0x84 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4a66 }, + {0x54022 ,0x4a08 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0x8400 }, + {0x54033 ,0x3100 }, + {0x54034 ,0x6600 }, + {0x54035 ,0x84a }, + {0x54036 ,0x4a }, + {0x54037 ,0x1600 }, + {0x54038 ,0x8400 }, + {0x54039 ,0x3100 }, + {0x5403a ,0x6600 }, + {0x5403b ,0x84a }, + {0x5403c ,0x4a }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* P0 2D message block paremeter for training firmware */ +static struct dram_cfg_param ddr_fsp0_2d_cfg[] = { + {0xd0000 ,0x0 }, + {0x54003 ,0xc80 }, + {0x54004 ,0x2 }, + {0x54005 ,0x2228 }, + {0x54006 ,0x11 }, + {0x54008 ,0x61 }, + {0x54009 ,0xc8 }, + {0x5400b ,0x2 }, + {0x5400d ,0x100 }, + {0x5400f ,0x100 }, + {0x54010 ,0x1f7f }, + {0x54012 ,0x110 }, + {0x54019 ,0x2dd4 }, + {0x5401a ,0x31 }, + {0x5401b ,0x4a66 }, + {0x5401c ,0x4a08 }, + {0x5401e ,0x16 }, + {0x5401f ,0x2dd4 }, + {0x54020 ,0x31 }, + {0x54021 ,0x4a66 }, + {0x54022 ,0x4a08 }, + {0x54024 ,0x16 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x1 }, + {0x54032 ,0xd400 }, + {0x54033 ,0x312d }, + {0x54034 ,0x6600 }, + {0x54035 ,0x84a }, + {0x54036 ,0x4a }, + {0x54037 ,0x1600 }, + {0x54038 ,0xd400 }, + {0x54039 ,0x312d }, + {0x5403a ,0x6600 }, + {0x5403b ,0x84a }, + {0x5403c ,0x4a }, + {0x5403d ,0x1600 }, + {0xd0000 ,0x1 }, +}; + +/* DRAM PHY init engine image */ +static struct dram_cfg_param ddr_phy_pie[] = { + {0xd0000 ,0x0 }, + {0x90000 ,0x10 }, + {0x90001 ,0x400 }, + {0x90002 ,0x10e }, + {0x90003 ,0x0 }, + {0x90004 ,0x0 }, + {0x90005 ,0x8 }, + {0x90029 ,0xb }, + {0x9002a ,0x480 }, + {0x9002b ,0x109 }, + {0x9002c ,0x8 }, + {0x9002d ,0x448 }, + {0x9002e ,0x139 }, + {0x9002f ,0x8 }, + {0x90030 ,0x478 }, + {0x90031 ,0x109 }, + {0x90032 ,0x0 }, + {0x90033 ,0xe8 }, + {0x90034 ,0x109 }, + {0x90035 ,0x2 }, + {0x90036 ,0x10 }, + {0x90037 ,0x139 }, + {0x90038 ,0xf }, + {0x90039 ,0x7c0 }, + {0x9003a ,0x139 }, + {0x9003b ,0x44 }, + {0x9003c ,0x630 }, + {0x9003d ,0x159 }, + {0x9003e ,0x14f }, + {0x9003f ,0x630 }, + {0x90040 ,0x159 }, + {0x90041 ,0x47 }, + {0x90042 ,0x630 }, + {0x90043 ,0x149 }, + {0x90044 ,0x4f }, + {0x90045 ,0x630 }, + {0x90046 ,0x179 }, + {0x90047 ,0x8 }, + {0x90048 ,0xe0 }, + {0x90049 ,0x109 }, + {0x9004a ,0x0 }, + {0x9004b ,0x7c8 }, + {0x9004c ,0x109 }, + {0x9004d ,0x0 }, + {0x9004e ,0x1 }, + {0x9004f ,0x8 }, + {0x90050 ,0x0 }, + {0x90051 ,0x45a }, + {0x90052 ,0x9 }, + {0x90053 ,0x0 }, + {0x90054 ,0x448 }, + {0x90055 ,0x109 }, + {0x90056 ,0x40 }, + {0x90057 ,0x630 }, + {0x90058 ,0x179 }, + {0x90059 ,0x1 }, + {0x9005a ,0x618 }, + {0x9005b ,0x109 }, + {0x9005c ,0x40c0 }, + {0x9005d ,0x630 }, + {0x9005e ,0x149 }, + {0x9005f ,0x8 }, + {0x90060 ,0x4 }, + {0x90061 ,0x48 }, + {0x90062 ,0x4040 }, + {0x90063 ,0x630 }, + {0x90064 ,0x149 }, + {0x90065 ,0x0 }, + {0x90066 ,0x4 }, + {0x90067 ,0x48 }, + {0x90068 ,0x40 }, + {0x90069 ,0x630 }, + {0x9006a ,0x149 }, + {0x9006b ,0x10 }, + {0x9006c ,0x4 }, + {0x9006d ,0x18 }, + {0x9006e ,0x0 }, + {0x9006f ,0x4 }, + {0x90070 ,0x78 }, + {0x90071 ,0x549 }, + {0x90072 ,0x630 }, + {0x90073 ,0x159 }, + {0x90074 ,0xd49 }, + {0x90075 ,0x630 }, + {0x90076 ,0x159 }, + {0x90077 ,0x94a }, + {0x90078 ,0x630 }, + {0x90079 ,0x159 }, + {0x9007a ,0x441 }, + {0x9007b ,0x630 }, + {0x9007c ,0x149 }, + {0x9007d ,0x42 }, + {0x9007e ,0x630 }, + {0x9007f ,0x149 }, + {0x90080 ,0x1 }, + {0x90081 ,0x630 }, + {0x90082 ,0x149 }, + {0x90083 ,0x0 }, + {0x90084 ,0xe0 }, + {0x90085 ,0x109 }, + {0x90086 ,0xa }, + {0x90087 ,0x10 }, + {0x90088 ,0x109 }, + {0x90089 ,0x9 }, + {0x9008a ,0x3c0 }, + {0x9008b ,0x149 }, + {0x9008c ,0x9 }, + {0x9008d ,0x3c0 }, + {0x9008e ,0x159 }, + {0x9008f ,0x18 }, + {0x90090 ,0x10 }, + {0x90091 ,0x109 }, + {0x90092 ,0x0 }, + {0x90093 ,0x3c0 }, + {0x90094 ,0x109 }, + {0x90095 ,0x18 }, + {0x90096 ,0x4 }, + {0x90097 ,0x48 }, + {0x90098 ,0x18 }, + {0x90099 ,0x4 }, + {0x9009a ,0x58 }, + {0x9009b ,0xa }, + {0x9009c ,0x10 }, + {0x9009d ,0x109 }, + {0x9009e ,0x2 }, + {0x9009f ,0x10 }, + {0x900a0 ,0x109 }, + {0x900a1 ,0x5 }, + {0x900a2 ,0x7c0 }, + {0x900a3 ,0x109 }, + {0x900a4 ,0x10 }, + {0x900a5 ,0x10 }, + {0x900a6 ,0x109 }, + {0x40000 ,0x811 }, + {0x40020 ,0x880 }, + {0x40040 ,0x0 }, + {0x40060 ,0x0 }, + {0x40001 ,0x4008 }, + {0x40021 ,0x83 }, + {0x40041 ,0x4f }, + {0x40061 ,0x0 }, + {0x40002 ,0x4040 }, + {0x40022 ,0x83 }, + {0x40042 ,0x51 }, + {0x40062 ,0x0 }, + {0x40003 ,0x811 }, + {0x40023 ,0x880 }, + {0x40043 ,0x0 }, + {0x40063 ,0x0 }, + {0x40004 ,0x720 }, + {0x40024 ,0xf }, + {0x40044 ,0x1740 }, + {0x40064 ,0x0 }, + {0x40005 ,0x16 }, + {0x40025 ,0x83 }, + {0x40045 ,0x4b }, + {0x40065 ,0x0 }, + {0x40006 ,0x716 }, + {0x40026 ,0xf }, + {0x40046 ,0x2001 }, + {0x40066 ,0x0 }, + {0x40007 ,0x716 }, + {0x40027 ,0xf }, + {0x40047 ,0x2800 }, + {0x40067 ,0x0 }, + {0x40008 ,0x716 }, + {0x40028 ,0xf }, + {0x40048 ,0xf00 }, + {0x40068 ,0x0 }, + {0x40009 ,0x720 }, + {0x40029 ,0xf }, + {0x40049 ,0x1400 }, + {0x40069 ,0x0 }, + {0x4000a ,0xe08 }, + {0x4002a ,0xc15 }, + {0x4004a ,0x0 }, + {0x4006a ,0x0 }, + {0x4000b ,0x623 }, + {0x4002b ,0x15 }, + {0x4004b ,0x0 }, + {0x4006b ,0x0 }, + {0x4000c ,0x4028 }, + {0x4002c ,0x80 }, + {0x4004c ,0x0 }, + {0x4006c ,0x0 }, + {0x4000d ,0xe08 }, + {0x4002d ,0xc1a }, + {0x4004d ,0x0 }, + {0x4006d ,0x0 }, + {0x4000e ,0x623 }, + {0x4002e ,0x1a }, + {0x4004e ,0x0 }, + {0x4006e ,0x0 }, + {0x4000f ,0x4040 }, + {0x4002f ,0x80 }, + {0x4004f ,0x0 }, + {0x4006f ,0x0 }, + {0x40010 ,0x2604 }, + {0x40030 ,0x15 }, + {0x40050 ,0x0 }, + {0x40070 ,0x0 }, + {0x40011 ,0x708 }, + {0x40031 ,0x5 }, + {0x40051 ,0x0 }, + {0x40071 ,0x2002 }, + {0x40012 ,0x8 }, + {0x40032 ,0x80 }, + {0x40052 ,0x0 }, + {0x40072 ,0x0 }, + {0x40013 ,0x2604 }, + {0x40033 ,0x1a }, + {0x40053 ,0x0 }, + {0x40073 ,0x0 }, + {0x40014 ,0x708 }, + {0x40034 ,0xa }, + {0x40054 ,0x0 }, + {0x40074 ,0x2002 }, + {0x40015 ,0x4040 }, + {0x40035 ,0x80 }, + {0x40055 ,0x0 }, + {0x40075 ,0x0 }, + {0x40016 ,0x60a }, + {0x40036 ,0x15 }, + {0x40056 ,0x1200 }, + {0x40076 ,0x0 }, + {0x40017 ,0x61a }, + {0x40037 ,0x15 }, + {0x40057 ,0x1300 }, + {0x40077 ,0x0 }, + {0x40018 ,0x60a }, + {0x40038 ,0x1a }, + {0x40058 ,0x1200 }, + {0x40078 ,0x0 }, + {0x40019 ,0x642 }, + {0x40039 ,0x1a }, + {0x40059 ,0x1300 }, + {0x40079 ,0x0 }, + {0x4001a ,0x4808 }, + {0x4003a ,0x880 }, + {0x4005a ,0x0 }, + {0x4007a ,0x0 }, + {0x900a7 ,0x0 }, + {0x900a8 ,0x790 }, + {0x900a9 ,0x11a }, + {0x900aa ,0x8 }, + {0x900ab ,0x7aa }, + {0x900ac ,0x2a }, + {0x900ad ,0x10 }, + {0x900ae ,0x7b2 }, + {0x900af ,0x2a }, + {0x900b0 ,0x0 }, + {0x900b1 ,0x7c8 }, + {0x900b2 ,0x109 }, + {0x900b3 ,0x10 }, + {0x900b4 ,0x2a8 }, + {0x900b5 ,0x129 }, + {0x900b6 ,0x8 }, + {0x900b7 ,0x370 }, + {0x900b8 ,0x129 }, + {0x900b9 ,0xa }, + {0x900ba ,0x3c8 }, + {0x900bb ,0x1a9 }, + {0x900bc ,0xc }, + {0x900bd ,0x408 }, + {0x900be ,0x199 }, + {0x900bf ,0x14 }, + {0x900c0 ,0x790 }, + {0x900c1 ,0x11a }, + {0x900c2 ,0x8 }, + {0x900c3 ,0x4 }, + {0x900c4 ,0x18 }, + {0x900c5 ,0xe }, + {0x900c6 ,0x408 }, + {0x900c7 ,0x199 }, + {0x900c8 ,0x8 }, + {0x900c9 ,0x8568 }, + {0x900ca ,0x108 }, + {0x900cb ,0x18 }, + {0x900cc ,0x790 }, + {0x900cd ,0x16a }, + {0x900ce ,0x8 }, + {0x900cf ,0x1d8 }, + {0x900d0 ,0x169 }, + {0x900d1 ,0x10 }, + {0x900d2 ,0x8558 }, + {0x900d3 ,0x168 }, + {0x900d4 ,0x70 }, + {0x900d5 ,0x788 }, + {0x900d6 ,0x16a }, + {0x900d7 ,0x1ff8 }, + {0x900d8 ,0x85a8 }, + {0x900d9 ,0x1e8 }, + {0x900da ,0x50 }, + {0x900db ,0x798 }, + {0x900dc ,0x16a }, + {0x900dd ,0x60 }, + {0x900de ,0x7a0 }, + {0x900df ,0x16a }, + {0x900e0 ,0x8 }, + {0x900e1 ,0x8310 }, + {0x900e2 ,0x168 }, + {0x900e3 ,0x8 }, + {0x900e4 ,0xa310 }, + {0x900e5 ,0x168 }, + {0x900e6 ,0xa }, + {0x900e7 ,0x408 }, + {0x900e8 ,0x169 }, + {0x900e9 ,0x6e }, + {0x900ea ,0x0 }, + {0x900eb ,0x68 }, + {0x900ec ,0x0 }, + {0x900ed ,0x408 }, + {0x900ee ,0x169 }, + {0x900ef ,0x0 }, + {0x900f0 ,0x8310 }, + {0x900f1 ,0x168 }, + {0x900f2 ,0x0 }, + {0x900f3 ,0xa310 }, + {0x900f4 ,0x168 }, + {0x900f5 ,0x1ff8 }, + {0x900f6 ,0x85a8 }, + {0x900f7 ,0x1e8 }, + {0x900f8 ,0x68 }, + {0x900f9 ,0x798 }, + {0x900fa ,0x16a }, + {0x900fb ,0x78 }, + {0x900fc ,0x7a0 }, + {0x900fd ,0x16a }, + {0x900fe ,0x68 }, + {0x900ff ,0x790 }, + {0x90100 ,0x16a }, + {0x90101 ,0x8 }, + {0x90102 ,0x8b10 }, + {0x90103 ,0x168 }, + {0x90104 ,0x8 }, + {0x90105 ,0xab10 }, + {0x90106 ,0x168 }, + {0x90107 ,0xa }, + {0x90108 ,0x408 }, + {0x90109 ,0x169 }, + {0x9010a ,0x58 }, + {0x9010b ,0x0 }, + {0x9010c ,0x68 }, + {0x9010d ,0x0 }, + {0x9010e ,0x408 }, + {0x9010f ,0x169 }, + {0x90110 ,0x0 }, + {0x90111 ,0x8b10 }, + {0x90112 ,0x168 }, + {0x90113 ,0x0 }, + {0x90114 ,0xab10 }, + {0x90115 ,0x168 }, + {0x90116 ,0x0 }, + {0x90117 ,0x1d8 }, + {0x90118 ,0x169 }, + {0x90119 ,0x80 }, + {0x9011a ,0x790 }, + {0x9011b ,0x16a }, + {0x9011c ,0x18 }, + {0x9011d ,0x7aa }, + {0x9011e ,0x6a }, + {0x9011f ,0xa }, + {0x90120 ,0x0 }, + {0x90121 ,0x1e9 }, + {0x90122 ,0x8 }, + {0x90123 ,0x8080 }, + {0x90124 ,0x108 }, + {0x90125 ,0xf }, + {0x90126 ,0x408 }, + {0x90127 ,0x169 }, + {0x90128 ,0xc }, + {0x90129 ,0x0 }, + {0x9012a ,0x68 }, + {0x9012b ,0x9 }, + {0x9012c ,0x0 }, + {0x9012d ,0x1a9 }, + {0x9012e ,0x0 }, + {0x9012f ,0x408 }, + {0x90130 ,0x169 }, + {0x90131 ,0x0 }, + {0x90132 ,0x8080 }, + {0x90133 ,0x108 }, + {0x90134 ,0x8 }, + {0x90135 ,0x7aa }, + {0x90136 ,0x6a }, + {0x90137 ,0x0 }, + {0x90138 ,0x8568 }, + {0x90139 ,0x108 }, + {0x9013a ,0xb7 }, + {0x9013b ,0x790 }, + {0x9013c ,0x16a }, + {0x9013d ,0x1f }, + {0x9013e ,0x0 }, + {0x9013f ,0x68 }, + {0x90140 ,0x8 }, + {0x90141 ,0x8558 }, + {0x90142 ,0x168 }, + {0x90143 ,0xf }, + {0x90144 ,0x408 }, + {0x90145 ,0x169 }, + {0x90146 ,0xc }, + {0x90147 ,0x0 }, + {0x90148 ,0x68 }, + {0x90149 ,0x0 }, + {0x9014a ,0x408 }, + {0x9014b ,0x169 }, + {0x9014c ,0x0 }, + {0x9014d ,0x8558 }, + {0x9014e ,0x168 }, + {0x9014f ,0x8 }, + {0x90150 ,0x3c8 }, + {0x90151 ,0x1a9 }, + {0x90152 ,0x3 }, + {0x90153 ,0x370 }, + {0x90154 ,0x129 }, + {0x90155 ,0x20 }, + {0x90156 ,0x2aa }, + {0x90157 ,0x9 }, + {0x90158 ,0x0 }, + {0x90159 ,0x400 }, + {0x9015a ,0x10e }, + {0x9015b ,0x8 }, + {0x9015c ,0xe8 }, + {0x9015d ,0x109 }, + {0x9015e ,0x0 }, + {0x9015f ,0x8140 }, + {0x90160 ,0x10c }, + {0x90161 ,0x10 }, + {0x90162 ,0x8138 }, + {0x90163 ,0x10c }, + {0x90164 ,0x8 }, + {0x90165 ,0x7c8 }, + {0x90166 ,0x101 }, + {0x90167 ,0x8 }, + {0x90168 ,0x0 }, + {0x90169 ,0x8 }, + {0x9016a ,0x8 }, + {0x9016b ,0x448 }, + {0x9016c ,0x109 }, + {0x9016d ,0xf }, + {0x9016e ,0x7c0 }, + {0x9016f ,0x109 }, + {0x90170 ,0x0 }, + {0x90171 ,0xe8 }, + {0x90172 ,0x109 }, + {0x90173 ,0x47 }, + {0x90174 ,0x630 }, + {0x90175 ,0x109 }, + {0x90176 ,0x8 }, + {0x90177 ,0x618 }, + {0x90178 ,0x109 }, + {0x90179 ,0x8 }, + {0x9017a ,0xe0 }, + {0x9017b ,0x109 }, + {0x9017c ,0x0 }, + {0x9017d ,0x7c8 }, + {0x9017e ,0x109 }, + {0x9017f ,0x8 }, + {0x90180 ,0x8140 }, + {0x90181 ,0x10c }, + {0x90182 ,0x0 }, + {0x90183 ,0x1 }, + {0x90184 ,0x8 }, + {0x90185 ,0x8 }, + {0x90186 ,0x4 }, + {0x90187 ,0x8 }, + {0x90188 ,0x8 }, + {0x90189 ,0x7c8 }, + {0x9018a ,0x101 }, + {0x90006 ,0x0 }, + {0x90007 ,0x0 }, + {0x90008 ,0x8 }, + {0x90009 ,0x0 }, + {0x9000a ,0x0 }, + {0x9000b ,0x0 }, + {0xd00e7 ,0x400 }, + {0x90017 ,0x0 }, + {0x9001f ,0x2a }, + {0x90026 ,0x6a }, + {0x400d0 ,0x0 }, + {0x400d1 ,0x101 }, + {0x400d2 ,0x105 }, + {0x400d3 ,0x107 }, + {0x400d4 ,0x10f }, + {0x400d5 ,0x202 }, + {0x400d6 ,0x20a }, + {0x400d7 ,0x20b }, + {0x2003a ,0x2 }, + {0x2000b ,0x64 }, + {0x2000c ,0xc8 }, + {0x2000d ,0x7d0 }, + {0x2000e ,0x2c }, + {0x12000b ,0xc }, + {0x12000c ,0x19 }, + {0x12000d ,0xfa }, + {0x12000e ,0x10 }, + {0x22000b ,0x3 }, + {0x22000c ,0x6 }, + {0x22000d ,0x3e }, + {0x22000e ,0x10 }, + {0x9000c ,0x0 }, + {0x9000d ,0x173 }, + {0x9000e ,0x60 }, + {0x9000f ,0x6110 }, + {0x90010 ,0x2152 }, + {0x90011 ,0xdfbd }, + {0x90012 ,0x60 }, + {0x90013 ,0x6152 }, + {0x20010 ,0x5a }, + {0x20011 ,0x3 }, + {0x120010 ,0x5a }, + {0x120011 ,0x3 }, + {0x220010 ,0x5a }, + {0x220011 ,0x3 }, + {0x40080 ,0xe0 }, + {0x40081 ,0x12 }, + {0x40082 ,0xe0 }, + {0x40083 ,0x12 }, + {0x40084 ,0xe0 }, + {0x40085 ,0x12 }, + {0x140080 ,0xe0 }, + {0x140081 ,0x12 }, + {0x140082 ,0xe0 }, + {0x140083 ,0x12 }, + {0x140084 ,0xe0 }, + {0x140085 ,0x12 }, + {0x240080 ,0xe0 }, + {0x240081 ,0x12 }, + {0x240082 ,0xe0 }, + {0x240083 ,0x12 }, + {0x240084 ,0xe0 }, + {0x240085 ,0x12 }, + {0x400fd ,0xf }, + {0x10011 ,0x1 }, + {0x10012 ,0x1 }, + {0x10013 ,0x180 }, + {0x10018 ,0x1 }, + {0x10002 ,0x6209 }, + {0x100b2 ,0x1 }, + {0x101b4 ,0x1 }, + {0x102b4 ,0x1 }, + {0x103b4 ,0x1 }, + {0x104b4 ,0x1 }, + {0x105b4 ,0x1 }, + {0x106b4 ,0x1 }, + {0x107b4 ,0x1 }, + {0x108b4 ,0x1 }, + {0x11011 ,0x1 }, + {0x11012 ,0x1 }, + {0x11013 ,0x180 }, + {0x11018 ,0x1 }, + {0x11002 ,0x6209 }, + {0x110b2 ,0x1 }, + {0x111b4 ,0x1 }, + {0x112b4 ,0x1 }, + {0x113b4 ,0x1 }, + {0x114b4 ,0x1 }, + {0x115b4 ,0x1 }, + {0x116b4 ,0x1 }, + {0x117b4 ,0x1 }, + {0x118b4 ,0x1 }, + {0x12011 ,0x1 }, + {0x12012 ,0x1 }, + {0x12013 ,0x180 }, + {0x12018 ,0x1 }, + {0x12002 ,0x6209 }, + {0x120b2 ,0x1 }, + {0x121b4 ,0x1 }, + {0x122b4 ,0x1 }, + {0x123b4 ,0x1 }, + {0x124b4 ,0x1 }, + {0x125b4 ,0x1 }, + {0x126b4 ,0x1 }, + {0x127b4 ,0x1 }, + {0x128b4 ,0x1 }, + {0x13011 ,0x1 }, + {0x13012 ,0x1 }, + {0x13013 ,0x180 }, + {0x13018 ,0x1 }, + {0x13002 ,0x6209 }, + {0x130b2 ,0x1 }, + {0x131b4 ,0x1 }, + {0x132b4 ,0x1 }, + {0x133b4 ,0x1 }, + {0x134b4 ,0x1 }, + {0x135b4 ,0x1 }, + {0x136b4 ,0x1 }, + {0x137b4 ,0x1 }, + {0x138b4 ,0x1 }, + {0x2003a ,0x2 }, + {0xc0080 ,0x2 }, + {0xd0000 ,0x1 } +}; + +static struct dram_fsp_msg ddr_dram_fsp_msg[] = { + { +/* P0 3200mts 1D */ + .drate =3200 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = ddr_fsp0_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp0_cfg), + }, + { +/* P1 400mts 1D */ + .drate =400 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = ddr_fsp1_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp1_cfg), + }, + { +/* P2 100mts 1D */ + .drate =100 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = ddr_fsp2_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp2_cfg), + }, + { +/* P0 3200mts 2D */ + .drate =3200 , + .fw_type =FW_2D_IMAGE , + .fsp_cfg = ddr_fsp0_2d_cfg, + .fsp_cfg_num =ARRAY_SIZE (ddr_fsp0_2d_cfg), + }, +}; + +/* ddr timing config params */ +struct dram_timing_info dram_timing_2gb = { + .ddrc_cfg = ddr_ddrc_cfg, + .ddrc_cfg_num =ARRAY_SIZE (ddr_ddrc_cfg), + .ddrphy_cfg = ddr_ddrphy_cfg, + .ddrphy_cfg_num =ARRAY_SIZE (ddr_ddrphy_cfg), + .fsp_msg = ddr_dram_fsp_msg, + .fsp_msg_num =ARRAY_SIZE (ddr_dram_fsp_msg), + .ddrphy_trained_csr = ddr_ddrphy_trained_csr, + .ddrphy_trained_csr_num =ARRAY_SIZE (ddr_ddrphy_trained_csr), + .ddrphy_pie = ddr_phy_pie, + .ddrphy_pie_num =ARRAY_SIZE (ddr_phy_pie), + .fsp_table = {3200 ,400 ,100 , }, +}; +board/kontron/pitx_imx8m/lpddr4_timing_4gb.c new file +1853
-0@@ -0,0 +1,1853 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include <linux/kernel.h> +#include <asm/arch/ddr.h> +#include <asm/arch/lpddr4_define.h> + +static struct dram_cfg_param ddr_ddrc_cfg[] = { +/** Initialize DDRC registers **/ + {0x3d400304 ,0x1 }, + {0x3d400030 ,0x1 }, + {0x3d400000 ,0xa3080020 }, + {0x3d400028 ,0x0 }, + {0x3d400020 ,0x202 }, + {0x3d400024 ,0x3e800 }, + {0x3d400064 ,0x1800e0 }, + {0x3d4000d0 ,0xc003061c }, + {0x3d4000d4 ,0x9e0000 }, + {0x3d4000dc ,0xd4002d }, + {0x3d4000e0 ,0x310008 }, + {0x3d4000e8 ,0x66004a }, + {0x3d4000ec ,0x16004a }, + {0x3d400100 ,0x1a200624 }, + {0x3d400104 ,0x60636 }, + {0x3d40010c ,0xc0c000 }, + {0x3d400110 ,0x10040a10 }, + {0x3d400114 ,0x2040c0c }, + {0x3d400118 ,0x1010007 }, + {0x3d40011c ,0x401 }, + {0x3d400130 ,0x20600 }, + {0x3d400134 ,0xc100002 }, + {0x3d400138 ,0xe6 }, + {0x3d400144 ,0xa00050 }, + {0x3d400180 ,0xc3200018 }, + {0x3d400184 ,0x28061a8 }, + {0x3d400188 ,0x0 }, + {0x3d400190 ,0x497820a }, + {0x3d400194 ,0x80303 }, + {0x3d4001a0 ,0xe0400018 }, + {0x3d4001a4 ,0xdf00e4 }, + {0x3d4001a8 ,0x80000000 }, + {0x3d4001b0 ,0x11 }, + {0x3d4001b4 ,0x170a }, + {0x3d4001c0 ,0x1 }, + {0x3d4001c4 ,0x1 }, + {0x3d4000f4 ,0x639 }, + {0x3d400108 ,0x70e1617 }, + {0x3d400200 ,0x17 }, + {0x3d40020c ,0x0 }, + {0x3d400210 ,0x1f1f }, + {0x3d400204 ,0x80808 }, + {0x3d400214 ,0x7070707 }, + {0x3d400218 ,0x7070707 }, + {0x3d402020 ,0x0 }, + {0x3d402024 ,0x7d00 }, + {0x3d402050 ,0x20d040 }, + {0x3d402064 ,0x3001c }, + {0x3d4020dc ,0x840000 }, + {0x3d4020e0 ,0x310000 }, + {0x3d4020e8 ,0x66004a }, + {0x3d4020ec ,0x16004a }, + {0x3d402100 ,0xa040005 }, + {0x3d402104 ,0x30407 }, + {0x3d402108 ,0x203060b }, + {0x3d40210c ,0x505000 }, + {0x3d402110 ,0x2040202 }, + {0x3d402114 ,0x2030202 }, + {0x3d402118 ,0x1010004 }, + {0x3d40211c ,0x301 }, + {0x3d402130 ,0x20300 }, + {0x3d402134 ,0xa100002 }, + {0x3d402138 ,0x1d }, + {0x3d402144 ,0x14000a }, + {0x3d402180 ,0xc0640004 }, + {0x3d402190 ,0x3818200 }, + {0x3d402194 ,0x80303 }, + {0x3d4021b4 ,0x100 }, + {0x3d403020 ,0x0 }, + {0x3d403024 ,0x1f40 }, + {0x3d403050 ,0x20d040 }, + {0x3d403064 ,0x30007 }, + {0x3d4030dc ,0x840000 }, + {0x3d4030e0 ,0x310000 }, + {0x3d4030e8 ,0x66004a }, + {0x3d4030ec ,0x16004a }, + {0x3d403100 ,0xa010102 }, + {0x3d403104 ,0x30404 }, + {0x3d403108 ,0x203060b }, + {0x3d40310c ,0x505000 }, + {0x3d403110 ,0x2040202 }, + {0x3d403114 ,0x2030202 }, + {0x3d403118 ,0x1010004 }, + {0x3d40311c ,0x301 }, + {0x3d403130 ,0x20300 }, + {0x3d403134 ,0xa100002 }, + {0x3d403138 ,0x8 }, + {0x3d403144 ,0x50003 }, + {0x3d403180 ,0xc0190004 }, + {0x3d403190 ,0x3818200 }, + {0x3d403194 ,0x80303 }, + {0x3d4031b4 ,0x100 }, + {0x3d400244 ,0x0 }, + {0x3d400250 ,0x29001505 }, + {0x3d400254 ,0x2c }, + {0x3d40025c ,0x5900575b }, + {0x3d400264 ,0x90000096 }, + {0x3d40026c ,0x1000012c }, + {0x3d400300 ,0x16 }, + {0x3d400304 ,0x0 }, + {0x3d40030c ,0x0 }, + {0x3d400320 ,0x1 }, + {0x3d40036c ,0x11 }, + {0x3d400400 ,0x111 }, + {0x3d400404 ,0x10f3 }, + {0x3d400408 ,0x72ff }, + {0x3d400490 ,0x1 }, + {0x3d400494 ,0xe00 }, + {0x3d400498 ,0x62ffff }, + {0x3d40049c ,0xe00 }, + {0x3d4004a0 ,0xffff }, +}; + +/* PHY Initialize Configuration */ +struct dram_cfg_param ddr_ddrphy_cfg[] = { + {0x100a0 ,0x2 }, + {0x100a1 ,0x3 }, + {0x100a2 ,0x0 }, + {0x100a3 ,0x1 }, + {0x100a4 ,0x5 }, + {0x100a5 ,0x7 }, + {0x100a6 ,0x6 }, + {0x100a7 ,0x4 }, + {0x110a0 ,0x2 }, + {0x110a1 ,0x1 }, + {0x110a2 ,0x3 }, + {0x110a3 ,0x0 }, + {0x110a4 ,0x6 }, + {0x110a5 ,0x7 }, + {0x110a6 ,0x4 }, + {0x110a7 ,0x5 }, + {0x120a0 ,0x4 }, + {0x120a1 ,0x5 }, + {0x120a2 ,0x7 }, + {0x120a3 ,0x6 }, + {0x120a4 ,0x1 }, + {0x120a5 ,0x3 }, + {0x120a6 ,0x2 }, + {0x120a7 ,0x0 }, + {0x130a0 ,0x4 }, + {0x130a1 ,0x5 }, + {0x130a2 ,0x7 }, + {0x130a3 ,0x6 }, + {0x130a4 ,0x2 }, + {0x130a5 ,0x1 }, + {0x130a6 ,0x0 }, + {0x130a7 ,0x3 }, + {0x1005f ,0x1ff }, + {0x1015f ,0x1ff }, + {0x1105f ,0x1ff }, + {0x1115f ,0x1ff }, + {0x1205f ,0x1ff }, + {0x1215f ,0x1ff }, + {0x1305f ,0x1ff }, + {0x1315f ,0x1ff }, + {0x11005f ,0x1ff }, + {0x11015f ,0x1ff }, + {0x11105f ,0x1ff }, + {0x11115f ,0x1ff }, + {0x11205f ,0x1ff }, + {0x11215f ,0x1ff }, + {0x11305f ,0x1ff }, + {0x11315f ,0x1ff }, + {0x21005f ,0x1ff }, + {0x21015f ,0x1ff }, + {0x21105f ,0x1ff }, + {0x21115f ,0x1ff }, + {0x21205f ,0x1ff }, + {0x21215f ,0x1ff }, + {0x21305f ,0x1ff }, + {0x21315f ,0x1ff }, + {0x55 ,0x1ff }, + {0x1055 ,0x1ff }, + {0x2055 ,0x1ff }, + {0x3055 ,0x1ff }, + {0x4055 ,0x1ff }, + {0x5055 ,0x1ff }, + {0x6055 ,0x1ff }, + {0x7055 ,0x1ff }, + {0x8055 ,0x1ff }, + {0x9055 ,0x1ff }, + {0x200c5 ,0x19 }, + {0x1200c5 ,0x7 }, + {0x2200c5 ,0x7 }, + {0x2002e ,0x2 }, + {0x12002e ,0x2 }, + {0x22002e ,0x2 }, + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + {0x20024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x120024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x220024 ,0x1ab }, + {0x2003a ,0x0 }, + {0x20056 ,0x3 }, + {0x120056 ,0x3 }, + {0x220056 ,0x3 }, + {0x1004d ,0xe00 }, + {0x1014d ,0xe00 }, + {0x1104d ,0xe00 }, + {0x1114d ,0xe00 }, + {0x1204d ,0xe00 }, + {0x1214d ,0xe00 }, + {0x1304d ,0xe00 }, + {0x1314d ,0xe00 }, + {0x11004d ,0xe00 }, + {0x11014d ,0xe00 }, + {0x11104d ,0xe00 }, + {0x11114d ,0xe00 }, + {0x11204d ,0xe00 }, + {0x11214d ,0xe00 }, + {0x11304d ,0xe00 }, + {0x11314d ,0xe00 }, + {0x21004d ,0xe00 }, + {0x21014d ,0xe00 }, + {0x21104d ,0xe00 }, + {0x21114d ,0xe00 }, + {0x21204d ,0xe00 }, + {0x21214d ,0xe00 }, + {0x21304d ,0xe00 }, + {0x21314d ,0xe00 }, + {0x10049 ,0xeba }, + {0x10149 ,0xeba }, + {0x11049 ,0xeba }, + {0x11149 ,0xeba }, + {0x12049 ,0xeba }, + {0x12149 ,0xeba }, + {0x13049 ,0xeba }, + {0x13149 ,0xeba }, + {0x110049 ,0xeba }, + {0x110149 ,0xeba }, + {0x111049 ,0xeba }, + {0x111149 ,0xeba }, + {0x112049 ,0xeba }, + {0x112149 ,0xeba }, + {0x113049 ,0xeba }, + {0x113149 ,0xeba }, + {0x210049 ,0xeba }, + {0x210149 ,0xeba }, + {0x211049 ,0xeba }, + {0x211149 ,0xeba }, + {0x212049 ,0xeba }, + {0x212149 ,0xeba }, + {0x213049 ,0xeba }, + {0x213149 ,0xeba }, + {0x43 ,0x63 }, + {0x1043 ,0x63 }, + {0x2043 ,0x63 }, + {0x3043 ,0x63 }, + {0x4043 ,0x63 }, + {0x5043 ,0x63 }, + {0x6043 ,0x63 }, + {0x7043 ,0x63 }, + {0x8043 ,0x63 }, + {0x9043 ,0x63 }, + {0x20018 ,0x3 }, + {0x20075 ,0x4 }, + {0x20050 ,0x0 }, + {0x20008 ,0x320 }, + {0x120008 ,0x64 }, + {0x220008 ,0x19 }, + {0x20088 ,0x9 }, + {0x200b2 ,0xdc }, + {0x10043 ,0x5a1 }, + {0x10143 ,0x5a1 }, + {0x11043 ,0x5a1 }, + {0x11143 ,0x5a1 }, + {0x12043 ,0x5a1 }, + {0x12143 ,0x5a1 }, + {0x13043 ,0x5a1 }, + {0x13143 ,0x5a1 }, + {0x1200b2 ,0xdc }, + {0x110043 ,0x5a1 }, + {0x110143 ,0x5a1 }, + {0x111043 ,0x5a1 }, + {0x111143 ,0x5a1 }, + {0x112043 ,0x5a1 }, + {0x112143 ,0x5a1 }, + {0x113043 ,0x5a1 }, + {0x113143 ,0x5a1 }, + {0x2200b2 ,0xdc }, + {0x210043 ,0x5a1 }, + {0x210143 ,0x5a1 }, + {0x211043 ,0x5a1 }, + {0x211143 ,0x5a1 }, + {0x212043 ,0x5a1 }, + {0x212143 ,0x5a1 }, + {0x213043 ,0x5a1 }, + {0x213143 ,0x5a1 }, + {0x200fa ,0x1 }, + {0x1200fa ,0x1 }, + {0x2200fa ,0x1 }, + {0x20019 ,0x1 }, + {0x120019 ,0x1 }, + {0x220019 ,0x1 }, + {0x200f0 ,0x660 }, + {0x200f1 ,0x0 }, + {0x200f2 ,0x4444 }, + {0x200f3 ,0x8888 }, + {0x200f4 ,0x5665 }, + {0x200f5 ,0x0 }, + {0x200f6 ,0x0 }, + {0x200f7 ,0xf000 }, + {0x20025 ,0x0 }, + {0x2002d ,0x0 }, + {0x12002d ,0x0 }, + {0x22002d ,0x0 }, + {0x200c7 ,0x80 }, + {0x1200c7 ,0x80 }, + {0x2200c7 ,0x80 }, + {0x200ca ,0x106 }, + {0x1200ca ,0x106 }, + {0x2200ca ,0x106 }, + {0x20110 ,0x2 }, + {0x20111 ,0x3 }, + {0x20112 ,0x4 }, + {0x20113 ,0x5 }, + {0x20114 ,0x0 }, + {0x20115 ,0x1 }, +}; + +/* ddr phy trained csr */ +struct dram_cfg_param ddr_ddrphy_trained_csr[] = { + {0x200b2 ,0x0 }, + {0x1200b2 ,0x0 }, + {0x2200b2 ,0x0 }, + {0x200cb ,0x0 }, + {0x10043 ,0x0 }, + {0x110043 ,0x0 }, + {0x210043 ,0x0 }, + {0x10143 ,0x0 }, + {0x110143 ,0x0 }, + {0x210143 ,0x0 }, + {0x11043 ,0x0 }, + {0x111043 ,0x0 }, + {0x211043 ,0x0 }, + {0x11143 ,0x0 }, + {0x111143 ,0x0 }, + {0x211143 ,0x0 }, + {0x12043 ,0x0 }, + {0x112043 ,0x0 }, + {0x212043 ,0x0 }, + {0x12143 ,0x0 }, + {0x112143 ,0x0 }, + {0x212143 ,0x0 }, + {0x13043 ,0x0 }, + {0x113043 ,0x0 }, + {0x213043 ,0x0 }, + {0x13143 ,0x0 }, + {0x113143 ,0x0 }, + {0x213143 ,0x0 }, + {0x80 ,0x0 }, + {0x100080 ,0x0 }, + {0x200080 ,0x0 }, + {0x1080 ,0x0 }, + {0x101080 ,0x0 }, + {0x201080 ,0x0 }, + {0x2080 ,0x0 }, + {0x102080 ,0x0 }, + {0x202080 ,0x0 }, + {0x3080 ,0x0 }, + {0x103080 ,0x0 }, + {0x203080 ,0x0 }, + {0x4080 ,0x0 }, + {0x104080 ,0x0 }, + {0x204080 ,0x0 }, + {0x5080 ,0x0 }, + {0x105080 ,0x0 }, + {0x205080 ,0x0 }, + {0x6080 ,0x0 }, + {0x106080 ,0x0 }, + {0x206080 ,0x0 }, + {0x7080 ,0x0 }, + {0x107080 ,0x0 }, + {0x207080 ,0x0 }, + {0x8080 ,0x0 }, + {0x108080 ,0x0 }, + {0x208080 ,0x0 }, + {0x9080 ,0x0 }, + {0x109080 ,0x0 }, + {0x209080 ,0x0 }, + {0x10080 ,0x0 }, + {0x110080 ,0x0 }, + {0x210080 ,0x0 }, + {0x10180 ,0x0 }, + {0x110180 ,0x0 }, + {0x210180 ,0x0 }, + {0x11080 ,0x0 }, + {0x111080 ,0x0 }, + {0x211080 ,0x0 }, + {0x11180 ,0x0 }, + {0x111180 ,0x0 }, + {0x211180 ,0x0 }, + {0x12080 ,0x0 }, + {0x112080 ,0x0 }, + {0x212080 ,0x0 }, + {0x12180 ,0x0 }, + {0x112180 ,0x0 }, + {0x212180 ,0x0 }, + {0x13080 ,0x0 }, + {0x113080 ,0x0 }, + {0x213080 ,0x0 }, + {0x13180 ,0x0 }, + {0x113180 ,0x0 }, + {0x213180 ,0x0 }, + {0x10081 ,0x0 }, + {0x110081 ,0x0 }, + {0x210081 ,0x0 }, + {0x10181 ,0x0 }, + {0x110181 ,0x0 }, + {0x210181 ,0x0 }, + {0x11081 ,0x0 }, + {0x111081 ,0x0 }, + {0x211081 ,0x0 }, + {0x11181 ,0x0 }, + {0x111181 ,0x0 }, + {0x211181 ,0x0 }, + {0x12081 ,0x0 }, + {0x112081 ,0x0 }, + {0x212081 ,0x0 }, + {0x12181 ,0x0 }, + {0x112181 ,0x0 }, + {0x212181 ,0x0 }, + {0x13081 ,0x0 }, + {0x113081 ,0x0 }, + {0x213081 ,0x0 }, + {0x13181 ,0x0 }, + {0x113181 ,0x0 }, + {0x213181 ,0x0 }, + {0x100d0 ,0x0 }, + {0x1100d0 ,0x0 }, + {0x2100d0 ,0x0 }, + {0x101d0 ,0x0 }, + {0x1101d0 ,0x0 }, + {0x2101d0 ,0x0 }, + {0x110d0 ,0x0 }, + {0x1110d0 ,0x0 }, + {0x2110d0 ,0x0 }, + {0x111d0 ,0x0 }, + {0x1111d0 ,0x0 }, + {0x2111d0 ,0x0 }, + {0x120d0 ,0x0 }, + {0x1120d0 ,0x0 }, + {0x2120d0 ,0x0 }, + {0x121d0 ,0x0 }, + {0x1121d0 ,0x0 }, + {0x2121d0 ,0x0 }, + {0x130d0 ,0x0 }, + {0x1130d0 ,0x0 }, + {0x2130d0 ,0x0 }, + {0x131d0 ,0x0 }, + {0x1131d0 ,0x0 }, + {0x2131d0 ,0x0 }, + {0x100d1 ,0x0 }, + {0x1100d1 ,0x0 }, + {0x2100d1 ,0x0 }, + {0x101d1 ,0x0 }, + {0x1101d1 ,0x0 }, + {0x2101d1 ,0x0 }, + {0x110d1 ,0x0 }, + {0x1110d1 ,0x0 }, + {0x2110d1 ,0x0 }, + {0x111d1 ,0x0 }, + {0x1111d1 ,0x0 }, + {0x2111d1 ,0x0 }, + {0x120d1 ,0x0 }, + {0x1120d1 ,0x0 }, + {0x2120d1 ,0x0 }, + {0x121d1 ,0x0 }, + {0x1121d1 ,0x0 }, + {0x2121d1 ,0x0 }, + {0x130d1 ,0x0 }, + {0x1130d1 ,0x0 }, + {0x2130d1 ,0x0 }, + {0x131d1 ,0x0 }, + {0x1131d1 ,0x0 }, + {0x2131d1 ,0x0 }, + {0x10068 ,0x0 }, + {0x10168 ,0x0 }, + {0x10268 ,0x0 }, + {0x10368 ,0x0 }, + {0x10468 ,0x0 }, + {0x10568 ,0x0 }, + {0x10668 ,0x0 }, + {0x10768 ,0x0 }, + {0x10868 ,0x0 }, + {0x11068 ,0x0 }, + {0x11168 ,0x0 }, + {0x11268 ,0x0 }, + {0x11368 ,0x0 }, + {0x11468 ,0x0 }, + {0x11568 ,0x0 }, + {0x11668 ,0x0 }, + {0x11768 ,0x0 }, + {0x11868 ,0x0 }, + {0x12068 ,0x0 }, + {0x12168 ,0x0 }, + {0x12268 ,0x0 }, + {0x12368 ,0x0 }, + {0x12468 ,0x0 }, + {0x12568 ,0x0 }, + {0x12668 ,0x0 }, + {0x12768 ,0x0 }, + {0x12868 ,0x0 }, + {0x13068 ,0x0 }, + {0x13168 ,0x0 }, + {0x13268 ,0x0 }, + {0x13368 ,0x0 }, + {0x13468 ,0x0 }, + {0x13568 ,0x0 }, + {0x13668 ,0x0 }, + {0x13768 ,0x0 }, + {0x13868 ,0x0 }, + {0x10069 ,0x0 }, + {0x10169 ,0x0 }, + {0x10269 ,0x0 }, + {0x10369 ,0x0 }, + {0x10469 ,0x0 }, + {0x10569 ,0x0 }, + {0x10669 ,0x0 }, + {0x10769 ,0x0 }, + {0x10869 ,0x0 }, + {0x11069 ,0x0 }, + {0x11169 ,0x0 }, + {0x11269 ,0x0 }, + {0x11369 ,0x0 }, + {0x11469 ,0x0 }, + {0x11569 ,0x0 }, + {0x11669 ,0x0 }, + {0x11769 ,0x0 }, + {0x11869 ,0x0 }, + {0x12069 ,0x0 }, + {0x12169 ,0x0 }, + {0x12269 ,0x0 }, + {0x12369 ,0x0 }, + {0x12469 ,0x0 }, + {0x12569 ,0x0 }, + {0x12669 ,0x0 }, + {0x12769 ,0x0 }, + {0x12869 ,0x0 }, + {0x13069 ,0x0 }, + {0x13169 ,0x0 }, + {0x13269 ,0x0 }, + {0x13369 ,0x0 }, + {0x13469 ,0x0 }, + {0x13569 ,0x0 }, + {0x13669 ,0x0 }, + {0x13769 ,0x0 }, + {0x13869 ,0x0 }, + {0x1008c ,0x0 }, + {0x11008c ,0x0 }, + {0x21008c ,0x0 }, + {0x1018c ,0x0 }, + {0x11018c ,0x0 }, + {0x21018c ,0x0 }, + {0x1108c ,0x0 }, + {0x11108c ,0x0 }, + {0x21108c ,0x0 }, + {0x1118c ,0x0 }, + {0x11118c ,0x0 }, + {0x21118c ,0x0 }, + {0x1208c ,0x0 }, + {0x11208c ,0x0 }, + {0x21208c ,0x0 }, + {0x1218c ,0x0 }, + {0x11218c ,0x0 }, + {0x21218c ,0x0 }, + {0x1308c ,0x0 }, + {0x11308c ,0x0 }, + {0x21308c ,0x0 }, + {0x1318c ,0x0 }, + {0x11318c ,0x0 }, + {0x21318c ,0x0 }, + {0x1008d ,0x0 }, + {0x11008d ,0x0 }, + {0x21008d ,0x0 }, + {0x1018d ,0x0 }, + {0x11018d ,0x0 }, + {0x21018d ,0x0 }, + {0x1108d ,0x0 }, + {0x11108d ,0x0 }, + {0x21108d ,0x0 }, + {0x1118d ,0x0 }, + {0x11118d ,0x0 }, + {0x21118d ,0x0 }, + {0x1208d ,0x0 }, + {0x11208d ,0x0 }, + {0x21208d ,0x0 }, + {0x1218d ,0x0 }, + {0x11218d ,0x0 }, + {0x21218d ,0x0 }, + {0x1308d ,0x0 }, + {0x11308d ,0x0 }, + {0x21308d ,0x0 }, + {0x1318d ,0x0 }, + {0x11318d ,0x0 }, + {0x21318d ,0x0 }, + {0x100c0 ,0x0 }, + {0x1100c0 ,0x0 }, + {0x2100c0 ,0x0 }, + {0x101c0 ,0x0 }, + {0x1101c0 ,0x0 }, + {0x2101c0 ,0x0 }, + {0x102c0 ,0x0 }, + {0x1102c0 ,0x0 }, + {0x2102c0 ,0x0 }, + {0x103c0 ,0x0 }, + {0x1103c0 ,0x0 }, + {0x2103c0 ,0x0 }, + {0x104c0 ,0x0 }, + {0x1104c0 ,0x0 }, + {0x2104c0 ,0x0 }, + {0x105c0 ,0x0 }, + {0x1105c0 ,0x0 }, + {0x2105c0 ,0x0 }, + {0x106c0 ,0x0 }, + {0x1106c0 ,0x0 }, + {0x2106c0 ,0x0 }, + {0x107c0 ,0x0 }, + {0x1107c0 ,0x0 }, + {0x2107c0 ,0x0 }, + {0x108c0 ,0x0 }, + {0x1108c0 ,0x0 }, + {0x2108c0 ,0x0 }, + {0x110c0 ,0x0 }, + {0x1110c0 ,0x0 }, + {0x2110c0 ,0x0 }, + {0x111c0 ,0x0 }, + {0x1111c0 ,0x0 }, + {0x2111c0 ,0x0 }, + {0x112c0 ,0x0 }, + {0x1112c0 ,0x0 }, + {0x2112c0 ,0x0 }, + {0x113c0 ,0x0 }, + {0x1113c0 ,0x0 }, + {0x2113c0 ,0x0 }, + {0x114c0 ,0x0 }, + {0x1114c0 ,0x0 }, + {0x2114c0 ,0x0 }, + {0x115c0 ,0x0 }, + {0x1115c0 ,0x0 }, + {0x2115c0 ,0x0 }, + {0x116c0 ,0x0 }, + {0x1116c0 ,0x0 }, + {0x2116c0 ,0x0 }, + {0x117c0 ,0x0 }, + {0x1117c0 ,0x0 }, + {0x2117c0 ,0x0 }, + {0x118c0 ,0x0 }, + {0x1118c0 ,0x0 }, + {0x2118c0 ,0x0 }, + {0x120c0 ,0x0 }, + {0x1120c0 ,0x0 }, + {0x2120c0 ,0x0 }, + {0x121c0 ,0x0 }, + {0x1121c0 ,0x0 }, + {0x2121c0 ,0x0 }, + {0x122c0 ,0x0 }, + {0x1122c0 ,0x0 }, + {0x2122c0 ,0x0 }, + {0x123c0 ,0x0 }, + {0x1123c0 ,0x0 }, + {0x2123c0 ,0x0 }, + {0x124c0 ,0x0 }, + {0x1124c0 ,0x0 }, + {0x2124c0 ,0x0 }, + {0x125c0 ,0x0 }, + {0x1125c0 ,0x0 }, + {0x2125c0 ,0x0 }, + {0x126c0 ,0x0 }, + {0x1126c0 ,0x0 }, + {0x2126c0 ,0x0 }, + {0x127c0 ,0x0 }, + {0x1127c0 ,0x0 }, + {0x2127c0 ,0x0 }, + {0x128c0 ,0x0 }, + {0x1128c0 ,0x0 }, + {0x2128c0 ,0x0 }, + {0x130c0 ,0x0 }, + {0x1130c0 ,0x0 }, + {0x2130c0 ,0x0 }, + {0x131c0 ,0x0 }, + {0x1131c0 ,0x0 }, + {0x2131c0 ,0x0 }, + {0x132c0 ,0x0 }, + {0x1132c0 ,0x0 }, + {0x2132c0 ,0x0 }, + {0x133c0 ,0x0 }, + {0x1133c0 ,0x0 }, + {0x2133c0 ,0x0 }, + {0x134c0 ,0x0 }, + {0x1134c0 ,0x0 }, + {0x2134c0 ,0x0 }, + {0x135c0 ,0x0 }, + {0x1135c0 ,0x0 }, + {0x2135c0 ,0x0 }, + {0x136c0 ,0x0 }, + {0x1136c0 ,0x0 }, + {0x2136c0 ,0x0 }, + {0x137c0 ,0x0 }, + {0x1137c0 ,0x0 }, + {0x2137c0 ,0x0 }, + {0x138c0 ,0x0 }, + {0x1138c0 ,0x0 }, + {0x2138c0 ,0x0 }, + {0x100c1 ,0x0 }, + {0x1100c1 ,0x0 }, + {0x2100c1 ,0x0 }, + {0x101c1 ,0x0 }, + {0x1101c1 ,0x0 }, + {0x2101c1 ,0x0 }, + {0x102c1 ,0x0 }, + {0x1102c1 ,0x0 }, + {0x2102c1 ,0x0 }, + {0x103c1 ,0x0 }, + {0x1103c1 ,0x0 }, + {0x2103c1 ,0x0 }, + {0x104c1 ,0x0 }, + {0x1104c1 ,0x0 }, + {0x2104c1 ,0x0 }, + {0x105c1 ,0x0 }, + {0x1105c1 ,0x0 }, + {0x2105c1 ,0x0 }, + {0x106c1 ,0x0 }, + {0x1106c1 ,0x0 }, + {0x2106c1 ,0x0 }, + {0x107c1 ,0x0 }, + {0x1107c1 ,0x0 }, + {0x2107c1 ,0x0 }, + {0x108c1 ,0x0 }, + {0x1108c1 ,0x0 }, + {0x2108c1 ,0x0 }, + {0x110c1 ,0x0 }, + {0x1110c1 ,0x0 }, + {0x2110c1 ,0x0 }, + {0x111c1 ,0x0 }, + {0x1111c1 ,0x0 }, + {0x2111c1 ,0x0 }, + {0x112c1 ,0x0 }, + {0x1112c1 ,0x0 }, + {0x2112c1 ,0x0 }, + {0x113c1 ,0x0 }, + {0x1113c1 ,0x0 }, + {0x2113c1 ,0x0 }, + {0x114c1 ,0x0 }, + {0x1114c1 ,0x0 }, + {0x2114c1 ,0x0 }, + {0x115c1 ,0x0 }, + {0x1115c1 ,0x0 }, + {0x2115c1 ,0x0 }, + {0x116c1 ,0x0 }, + {0x1116c1 ,0x0 }, + {0x2116c1 ,0x0 }, + {0x117c1 ,0x0 }, + {0x1117c1 ,0x0 }, + {0x2117c1 ,0x0 }, + {0x118c1 ,0x0 }, + {0x1118c1 ,0x0 }, + {0x2118c1 ,0x0 }, + {0x120c1 ,0x0 }, + {0x1120c1 ,0x0 }, + {0x2120c1 ,0x0 }, + {0x121c1 ,0x0 }, + {0x1121c1 ,0x0 }, + {0x2121c1 ,0x0 }, + {0x122c1 ,0x0 }, + {0x1122c1 ,0x0 }, + {0x2122c1 ,0x0 }, + {0x123c1 ,0x0 }, + {0x1123c1 ,0x0 }, + {0x2123c1 ,0x0 }, + {0x124c1 ,0x0 }, + {0x1124c1 ,0x0 }, + {0x2124c1 ,0x0 }, + {0x125c1 ,0x0 }, + {0x1125c1 ,0x0 }, + {0x2125c1 ,0x0 }, + {0x126c1 ,0x0 }, + {0x1126c1 ,0x0 }, + {0x2126c1 ,0x0 }, + {0x127c1 ,0x0 }, + {0x1127c1 ,0x0 }, + {0x2127c1 ,0x0 }, + {0x128c1 ,0x0 }, + {0x1128c1 ,0x0 }, + {0x2128c1 ,0x0 }, + {0x130c1 ,0x0 }, + {0x1130c1 ,0x0 }, + {0x2130c1 ,0x0 }, + {0x131c1 ,0x0 }, + {0x1131c1 ,0x0 }, + {0x2131c1 ,0x0 }, + {0x132c1 ,0x0 }, + {0x1132c1 ,0x0 }, + {0x2132c1 ,0x0 }, + {0x133c1 ,0x0 }, + {0x1133c1 ,0x0 }, + {0x2133c1 ,0x0 }, + {0x134c1 ,0x0 }, + {0x1134c1 ,0x0 }, + {0x2134c1 ,0x0 }, + {0x135c1 ,0x0 }, + {0x1135c1 ,0x0 }, + {0x2135c1 ,0x0 }, + {0x136c1 ,0x0 }, + {0x1136c1 ,0x0 }, + {0x2136c1 ,0x0 }, + {0x137c1 ,0x0 }, + {0x1137c1 ,0x0 }, + {0x2137c1 ,0x0 }, + {0x138c1 ,0x0 }, + {0x1138c1 ,0x0 }, + {0x2138c1 ,0x0 }, + {0x10020 ,0x0 }, + {0x110020 ,0x0 }, + {0x210020 ,0x0 }, + {0x11020 ,0x0 }, + {0x111020 ,0x0 }, + {0x211020 ,0x0 }, + {0x12020 ,0x0 }, + {0x112020 ,0x0 }, + {0x212020 ,0x0 }, + {0x13020 ,0x0 }, + {0x113020 ,0x0 }, + {0x213020 ,0x0 }, + {0x20072 ,0x0 }, + {0x20073 ,0x0 }, + {0x20074 ,0x0 }, + {0x100aa ,0x0 }, + {0x110aa ,0x0 }, + {0x120aa ,0x0 }, + {0x130aa ,0x0 }, + {0x20010 ,0x0 }, + {0x120010 ,0x0 }, + {0x220010 ,0x0 }, + {0x20011 ,0x0 }, + {0x120011 ,0x0 }, + {0x220011 ,0x0 }, + {0x100ae ,0x0 }, + {0x1100ae ,0x0 }, + {0x2100ae ,0x0 }, + {0x100af ,0x0 }, + {0x1100af ,0x0 }, + {0x2100af ,0x0 }, + {0x110ae ,0x0 }, + {0x1110ae ,0x0 }, + {0x2110ae ,0x0 }, + {0x110af ,0x0 }, + {0x1110af ,0x0 }, + {0x2110af ,0x0 }, + {0x120ae ,0x0 }, + {0x1120ae ,0x0 }, + {0x2120ae ,0x0 }, + {0x120af ,0x0 }, + {0x1120af ,0x0 }, + {0x2120af ,0x0 }, + {0x130ae ,0x0 }, + {0x1130ae ,0x0 }, + {0x2130ae ,0x0 }, + {0x130af ,0x0 }, + {0x1130af ,0x0 }, + {0x2130af ,0x0 }, + {0x20020 ,0x0 }, + {0x120020 ,0x0 }, + {0x220020 ,0x0 }, + {0x100a0 ,0x0 }, + {0x100a1 ,0x0 }, + {0x100a2 ,0x0 }, + {0x100a3 ,0x0 }, + {0x100a4 ,0x0 }, + {0x100a5 ,0x0 }, + {0x100a6 ,0x0 }, + {0x100a7 ,0x0 }, + {0x110a0 ,0x0 }, + {0x110a1 ,0x0 }, + {0x110a2 ,0x0 }, + {0x110a3 ,0x0 }, + {0x110a4 ,0x0 }, + {0x110a5 ,0x0 }, + {0x110a6 ,0x0 }, + {0x110a7 ,0x0 }, + {0x120a0 ,0x0 }, + {0x120a1 ,0x0 }, + {0x120a2 ,0x0 }, + {0x120a3 ,0x0 }, + {0x120a4 ,0x0 }, + {0x120a5 ,0x0 }, + {0x120a6 ,0x0 }, + {0x120a7 ,0x0 }, + {0x130a0 ,0x0 }, + {0x130a1 ,0x0 }, + {0x130a2 ,0x0 }, + {0x130a3 ,0x0 }, + {0x130a4 ,0x0 }, + {0x130a5 ,0x0 }, + {0x130a6 ,0x0 }, + {0x130a7 ,0x0 }, + {0x2007c ,0x0 }, + {0x12007c ,0x0 }, + {0x22007c ,0x0 }, + {0x2007d ,0x0 }, + {0x12007d ,0x0 }, + {0x22007d ,0x0 }, + {0x400fd ,0x0 }, + {0x400c0 ,0x0 }, + {0x90201 ,0x0 }, + {0x190201 ,0x0 }, + {0x290201 ,0x0 }, + {0x90202 ,0x0 }, + {0x190202 ,0x0 }, + {0x290202 ,0x0 }, + {0x90203 ,0x0 }, + {0x190203 ,0x0 }, + {0x290203 ,0x0 }, + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + {0x90205 ,0x0 }, + {0x190205 ,0x0 }, + {0x290205 ,0x0 },Lines of this file are not shown. View the raw message.
board/kontron/pitx_imx8m/pitx_imx8m.c new file +156
-0Lines of this file are not shown. View the raw message.
board/kontron/pitx_imx8m/spl.c new file +327
-0Lines of this file are not shown. View the raw message.
configs/kontron_pitx_imx8m_defconfig new file +87
-0Lines of this file are not shown. View the raw message.
doc/board/kontron/pitx-imx8m.rst new file +67
-0Lines of this file are not shown. View the raw message.
include/configs/kontron_pitx_imx8m.h new file +111
-0Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Part of the diff is not shown here. View the raw message.
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Signature · 1 line
Heiko
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Quoted 26 lines · Heiko Thiery
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+
Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----
With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000 ./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----
Currently I do not have an idea how to handle that. Anyone else?
Signature · 1 line
Heiko
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 65 lines
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----
Quoted 1 line
Currently I do not have an idea how to handle that. Anyone else?
I thought about it a little and did a quick hack. What do you think about dummy files being generated for buildman? I had buildman generate the blobs needed by binman. So at least the build runs through successfully. I don't know yet how to integrate this sensibly into buildman or if this is useful for the maintainers at all. But this would get rid of the warnings and errors that come from binman.
tools/buildman/board.py +22 -0
@@ -96,6 +96,28 @@ class Board: self.vendor, self.soc, self.options] self.build_it = False + def create_dummy_files(self, work_dir): + import configparser + import os + + settings = configparser.SafeConfigParser() + config_fname = '%s/.buildman/' % os.getenv('HOME') + if os.path.exists(config_fname): + settings.read(config_fname) + + if self.target == "kontron_pitx_imx8m": + + dummy_files = ['bl31.bin', + 'signed_hdmi_imx8m.bin', + 'lpddr4_pmu_train_1d_imem.bin', + 'lpddr4_pmu_train_1d_dmem.bin', + 'lpddr4_pmu_train_2d_imem.bin', + 'lpddr4_pmu_train_2d_dmem.bin' + ] + for dummy_file in dummy_files: + dummy = os.path.join(work_dir, 'build', dummy_file) + with open(dummy, "wb") as out: + out.truncate(1024) class Boards: """Manage a list of boards."""
tools/buildman/builderthread.py +1 -0
@@ -475,6 +475,7 @@ class BuilderThread(threading.Thread): """ brd = job.board work_dir = self.builder.GetThreadDir(self.thread_num) + brd.create_dummy_files(work_dir) self.toolchain = None if job.commits: # Run 'make board_defconfig' on the first commit
Signature · 1 line
Heiko
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Heiko,
Quoted 69 lines · Heiko Thiery
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 65 lines
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----
Quoted 4 lines
Quoted 1 line
Currently I do not have an idea how to handle that. Anyone else?
I thought about it a little and did a quick hack. What do you think about dummy files being generated for buildman?
I had quite the same idea...
Quoted 3 lines
I had buildman
generate the blobs needed by binman. So at least the build runs through successfully.
But it should be checked if files are present - I guess there are people relying on buildman to produce the functional bootloader, and a dummy file cannot overwrite the right one if present.
Quoted 44 lines
I don't know yet how to integrate this sensibly
into buildman or if this is useful for the maintainers at all. But this would get rid of the warnings and errors that come from binman.tools/buildman/board.py +22
-0@@ -96,6 +96,28 @@ class Board: self.vendor, self.soc, self.options] self.build_it = False + def create_dummy_files(self, work_dir): + import configparser + import os + + settings = configparser.SafeConfigParser() + config_fname = '%s/.buildman/' % os.getenv('HOME') + if os.path.exists(config_fname): + settings.read(config_fname) + + if self.target == "kontron_pitx_imx8m": + + dummy_files = ['bl31.bin', + 'signed_hdmi_imx8m.bin', + 'lpddr4_pmu_train_1d_imem.bin', + 'lpddr4_pmu_train_1d_dmem.bin', + 'lpddr4_pmu_train_2d_imem.bin', + 'lpddr4_pmu_train_2d_dmem.bin' + ] + for dummy_file in dummy_files: + dummy = os.path.join(work_dir, 'build', dummy_file) + with open(dummy, "wb") as out: + out.truncate(1024) class Boards: """Manage a list of boards."""tools/buildman/builderthread.py +0
-0
tools/buildman/builderthread.py class BuilderThread(threading.Thread): · line 481
Quoted 7 lines
tools/buildman/builderthread.py +1
-0@@ -475,6 +475,7 @@ class BuilderThread(threading.Thread): """ brd = job.board work_dir = self.builder.GetThreadDir(self.thread_num) + brd.create_dummy_files(work_dir) self.toolchain = None if job.commits: # Run 'make board_defconfig' on the first commit
Best regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi,
Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 80 lines
Hi Heiko,
Quoted 69 lines · Heiko Thiery
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 65 lines
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----Quoted 4 lines
Quoted 1 line
Currently I do not have an idea how to handle that. Anyone else?
I thought about it a little and did a quick hack. What do you think about dummy files being generated for buildman?
I had quite the same idea...
Quoted 7 lines
Quoted 3 lines
I had buildman
generate the blobs needed by binman. So at least the build runs through successfully.But it should be checked if files are present - I guess there are people relying on buildman to produce the functional bootloader, and a dummy file cannot overwrite the right one if present.
Sure. As said ,this was only a quick hack to see if it could work. Another thing is if there should be a config for each board that says what files have to be created.
Quoted 51 lines
Quoted 51 lines
I don't know yet how to integrate this sensibly
into buildman or if this is useful for the maintainers at all. But this would get rid of the warnings and errors that come from binman.tools/buildman/board.py +22
-0@@ -96,6 +96,28 @@ class Board: self.vendor, self.soc, self.options] self.build_it = False + def create_dummy_files(self, work_dir): + import configparser + import os + + settings = configparser.SafeConfigParser() + config_fname = '%s/.buildman/' % os.getenv('HOME') + if os.path.exists(config_fname): + settings.read(config_fname) + + if self.target == "kontron_pitx_imx8m": + + dummy_files = ['bl31.bin', + 'signed_hdmi_imx8m.bin', + 'lpddr4_pmu_train_1d_imem.bin', + 'lpddr4_pmu_train_1d_dmem.bin', + 'lpddr4_pmu_train_2d_imem.bin', + 'lpddr4_pmu_train_2d_dmem.bin' + ] + for dummy_file in dummy_files: + dummy = os.path.join(work_dir, 'build', dummy_file) + with open(dummy, "wb") as out: + out.truncate(1024) class Boards: """Manage a list of boards."""tools/buildman/builderthread.py +1
-0@@ -475,6 +475,7 @@ class BuilderThread(threading.Thread): """ brd = job.board work_dir = self.builder.GetThreadDir(self.thread_num) + brd.create_dummy_files(work_dir) self.toolchain = None if job.commits: # Run 'make board_defconfig' on the first commit
Signature · 1 line
Heiko
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Heiko,
Quoted 78 lines · Heiko Thiery
Hi,
Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 74 lines
Hi Heiko,
Quoted 70 lines · Heiko Thiery
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 66 lines
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----Currently I do not have an idea how to handle that. Anyone else?
If I understand correctly:
1.You don't have these blobs in the tree so don't want to fail a build in CI, which is why binman's blob-ext is used
2. You sometimes need to ensure that they do exist
Should we add a cmdline flag to binman to require all external blobs?
Could we drop the blobs and add code to generate them, or put the date in a C struct?
Quoted 65 lines
Quoted 6 lines
Quoted 3 lines
I thought about it a little and did a quick hack. What do you think about dummy files being generated for buildman?
I had quite the same idea...
Quoted 7 lines
Quoted 3 lines
I had buildman
generate the blobs needed by binman. So at least the build runs through successfully.But it should be checked if files are present - I guess there are people relying on buildman to produce the functional bootloader, and a dummy file cannot overwrite the right one if present.
Sure. As said ,this was only a quick hack to see if it could work. Another thing is if there should be a config for each board that says what files have to be created.
Quoted 47 lines
Quoted 47 lines
I don't know yet how to integrate this sensibly
into buildman or if this is useful for the maintainers at all. But this would get rid of the warnings and errors that come from binman.tools/buildman/board.py +22
-0@@ -96,6 +96,28 @@ class Board: self.vendor, self.soc, self.options] self.build_it = False + def create_dummy_files(self, work_dir): + import configparser + import os + + settings = configparser.SafeConfigParser() + config_fname = '%s/.buildman/' % os.getenv('HOME') + if os.path.exists(config_fname): + settings.read(config_fname) + + if self.target == "kontron_pitx_imx8m": + + dummy_files = ['bl31.bin', + 'signed_hdmi_imx8m.bin', + 'lpddr4_pmu_train_1d_imem.bin', + 'lpddr4_pmu_train_1d_dmem.bin', + 'lpddr4_pmu_train_2d_imem.bin', + 'lpddr4_pmu_train_2d_dmem.bin' + ] + for dummy_file in dummy_files: + dummy = os.path.join(work_dir, 'build', dummy_file) + with open(dummy, "wb") as out: + out.truncate(1024) class Boards: """Manage a list of boards."""tools/buildman/builderthread.py +1
-0@@ -475,6 +475,7 @@ class BuilderThread(threading.Thread): """ brd = job.board work_dir = self.builder.GetThreadDir(self.thread_num) + brd.create_dummy_files(work_dir)
Quoted 8 lines
Quoted 4 lines
tools/buildman/builderthread.py class BuilderThread(threading.Thread): · line 481
Quoted 4 lines
tools/buildman/builderthread.py +0
-0self.toolchain = None if job.commits: # Run 'make board_defconfig' on the first commit--
Heiko
Regards,
Simon
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Simon,
Am Fr., 22. Okt. 2021 um 18:07 Uhr schrieb Simon Glass <[email protected]>:
Quoted 81 lines
Hi Heiko,
Quoted 77 lines · Heiko Thiery
Hi,
Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 73 lines
Hi Heiko,
Quoted 69 lines · Heiko Thiery
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 65 lines
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----
Quoted 6 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Currently I do not have an idea how to handle that. Anyone else?
If I understand correctly:
1.You don't have these blobs in the tree so don't want to fail a build in CI, which is why binman's blob-ext is used
Correct, for the imx8mq e.g. the signed_hdmi_imx8m.bin is required that comes from NXP and has to be copied to the u-boot build dir.
Quoted 1 line
2. You sometimes need to ensure that they do exist
For the build the "signed_hdmi_imx8m.bin" is required to successfully build.
Quoted 1 line
Should we add a cmdline flag to binman to require all external blobs?
I do not understand that. What should happen if this flag is present?
Quoted 2 lines
Could we drop the blobs and add code to generate them, or put the date in a C struct?
No, this is not possible because they are delivered by NXP from the firmware-imx package and has to be copied from there.
Quoted 76 lines
Quoted 65 lines
Quoted 6 lines
Quoted 3 lines
I thought about it a little and did a quick hack. What do you think about dummy files being generated for buildman?
I had quite the same idea...
Quoted 7 lines
Quoted 3 lines
I had buildman
generate the blobs needed by binman. So at least the build runs through successfully.But it should be checked if files are present - I guess there are people relying on buildman to produce the functional bootloader, and a dummy file cannot overwrite the right one if present.
Sure. As said ,this was only a quick hack to see if it could work. Another thing is if there should be a config for each board that says what files have to be created.
Quoted 47 lines
Quoted 47 lines
I don't know yet how to integrate this sensibly
into buildman or if this is useful for the maintainers at all. But this would get rid of the warnings and errors that come from binman.tools/buildman/board.py +22
-0@@ -96,6 +96,28 @@ class Board: self.vendor, self.soc, self.options] self.build_it = False + def create_dummy_files(self, work_dir): + import configparser + import os + + settings = configparser.SafeConfigParser() + config_fname = '%s/.buildman/' % os.getenv('HOME') + if os.path.exists(config_fname): + settings.read(config_fname) + + if self.target == "kontron_pitx_imx8m": + + dummy_files = ['bl31.bin', + 'signed_hdmi_imx8m.bin', + 'lpddr4_pmu_train_1d_imem.bin', + 'lpddr4_pmu_train_1d_dmem.bin', + 'lpddr4_pmu_train_2d_imem.bin', + 'lpddr4_pmu_train_2d_dmem.bin' + ] + for dummy_file in dummy_files: + dummy = os.path.join(work_dir, 'build', dummy_file) + with open(dummy, "wb") as out: + out.truncate(1024) class Boards: """Manage a list of boards."""tools/buildman/builderthread.py +1
-0@@ -475,6 +475,7 @@ class BuilderThread(threading.Thread): """ brd = job.board work_dir = self.builder.GetThreadDir(self.thread_num) + brd.create_dummy_files(work_dir)Quoted 8 lines
Quoted 4 lines
tools/buildman/builderthread.py class BuilderThread(threading.Thread): · line 481
Quoted 4 lines
tools/buildman/builderthread.py +0
-0self.toolchain = None if job.commits: # Run 'make board_defconfig' on the first commit--
HeikoRegards,
Simon
Signature · 1 line
Heiko
Re: [PATCH v6 2/2] board: kontron: pitx-imx8m: Add Kontron pitx-imx8m board support
Hi Heiko,
Quoted 101 lines · Heiko Thiery
Hi Simon,
Am Fr., 22. Okt. 2021 um 18:07 Uhr schrieb Simon Glass <[email protected]>:
Quoted 81 lines
Hi Heiko,
Quoted 77 lines · Heiko Thiery
Hi,
Am Fr., 22. Okt. 2021 um 14:37 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 73 lines
Hi Heiko,
Quoted 69 lines · Heiko Thiery
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:57 Uhr schrieb Heiko Thiery <[email protected]>:
Quoted 65 lines
Hi Stefano, Hi Simon,
Am Do., 21. Okt. 2021 um 15:29 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 33 lines · Heiko Thiery
Quoted 26 lines
Hi Stefano,
Am Do., 21. Okt. 2021 um 13:31 Uhr schrieb Stefano Babic <[email protected]>:
Quoted 22 lines
Hi Heiko,
Quoted 3 lines · Heiko Thiery
The Kontron pitx-imx8m is an NXP i.MX8MQ based board in the pITX form factor.
There is still something using binman that does not work with CI. Without CI, we load all firmware including signed_hdmi_imx8m.bin.
But on CI, file is not loaded, but instead of warnings, build for this board fails with :
+Image 'main-section' is missing external blobs and is non-functional:
blob-ext@1 blob-ext@2 blob-ext@3 blob-ext@4
+binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
+Quoted 4 lines
Quoted 1 line
Could you take a look ?
Sure. Could you point me to the right CI configuration?
Quoted 8 lines
Configuration is in .gitlab-ci.yml. For thsi board, buildman is called as part of aarch64 target, that is
buildman -o /tmp -P -E -W arm -x aarch64
Quoted 3 lines
I need to understand how the required imx-firmware files are copied to the u-boot dir. This seems to work already for e. g. the imx8mm boards. These require the lpdd* train fw files.
Here we seem to hit an issue with the CI. blobs (lpddr*) are required for the imx8mm boards. Binman reports the missing files only as a warning and buildman does not care about that:
----
+WARNING 'mkimage.flash.mkimage' not found, resulting binary is not-functional
----With the imx8mq boards switching to binman we also need an additional fw part (signed_hdmi_imx8m.bin). But other than the lpddr firmware as blob the signed_hmdi'_imx8m.bin is passed to mkimage and mkimage exits with an error. Thats leads to the error:
----
binman: Error 1 running 'mkimage -d ./mkimage.spl.mkimage -n spl/u-boot-spl.cfgout -T imx8mimage -e0x7e1000./mkimage-out.spl.mkimage': signed_hdmi_imx8m.bin: Can't open: No such file or directory
----Quoted 6 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Currently I do not have an idea how to handle that. Anyone else?
If I understand correctly:
1.You don't have these blobs in the tree so don't want to fail a build in CI, which is why binman's blob-ext is used
Correct, for the imx8mq e.g. the signed_hdmi_imx8m.bin is required that comes from NXP and has to be copied to the u-boot build dir.
Quoted 1 line
2. You sometimes need to ensure that they do exist
For the build the "signed_hdmi_imx8m.bin" is required to successfully build.
Quoted 1 line
Should we add a cmdline flag to binman to require all external blobs?
Quoted 7 lines
I do not understand that. What should happen if this flag is present?
Quoted 2 lines
Could we drop the blobs and add code to generate them, or put the date in a C struct?
No, this is not possible because they are delivered by NXP from the firmware-imx package and has to be copied from there.
Perhaps they should upstream that stuff and turn it into code in U-Boot?
Anyway, I think you are working on this, per the irc chat. [..]
Regards,
Simon