ARM: dts: elpida_ecb240abacn: Change Elpida compatible
PATCH 1/1 ARM: dts: elpida_ecb240abacn: Change Elpida compatible
Vendor prefix shouldn't start with capital letter. The Elpida Memory compatible was never used in practice, hence just correct the compatible.
--- arch/arm/boot/dts/elpida_ecb240abacn.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/elpida_ecb240abacn.dtsi +1 -1
@@ -5,7 +5,7 @@ / { elpida_ECB240ABACN: lpddr2 { - compatible = "Elpida,ECB240ABACN","jedec,lpddr2-s4"; + compatible = "elpida,ECB240ABACN","jedec,lpddr2-s4"; density = <2048>; io-width = <32>;
Signature · 1 line
2.32.0
20.10.2021 02:40, Dmitry Osipenko пишет:
Quoted 14 lines
Vendor prefix shouldn't start with capital letter. The Elpida Memory compatible was never used in practice, hence just correct the compatible.
Signed-off-by Dmitry Osipenko <[email protected]>--- arch/arm/boot/dts/elpida_ecb240abacn.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/boot/dts/elpida_ecb240abacn.dtsi +0
-0
arch/arm/boot/dts/elpida_ecb240abacn.dtsi line 11
Quoted 8 lines
arch/arm/boot/dts/elpida_ecb240abacn.dtsi +1
-1@@ -5,7 +5,7 @@ / { elpida_ECB240ABACN: lpddr2 { - compatible = "Elpida,ECB240ABACN","jedec,lpddr2-s4"; + compatible = "elpida,ECB240ABACN","jedec,lpddr2-s4"; density = <2048>; io-width = <32>;
This patch should go via OMAP tree since there is only OMAP board which uses this dtsi. To make it more clear, "elpida" variant is now documented in the bindings [1][2].
If there is no interest in taking the patch via OMAP tree, then it may go via the DT git tree. Rob, you should pick it up then.
Thanks!
Hi,
Quoted 28 lines · Dmitry Osipenko
20.10.2021 02:40, Dmitry Osipenko пишет:
Quoted 14 lines
Vendor prefix shouldn't start with capital letter. The Elpida Memory compatible was never used in practice, hence just correct the compatible.
Signed-off-by Dmitry Osipenko <[email protected]>--- arch/arm/boot/dts/elpida_ecb240abacn.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/boot/dts/elpida_ecb240abacn.dtsi +0
-0arch/arm/boot/dts/elpida_ecb240abacn.dtsi line 11
Quoted 8 lines
arch/arm/boot/dts/elpida_ecb240abacn.dtsi +1
-1@@ -5,7 +5,7 @@ / { elpida_ECB240ABACN: lpddr2 { - compatible = "Elpida,ECB240ABACN","jedec,lpddr2-s4"; + compatible = "elpida,ECB240ABACN","jedec,lpddr2-s4"; density = <2048>; io-width = <32>;This patch should go via OMAP tree since there is only OMAP board which uses this dtsi. To make it more clear, "elpida" variant is now documented in the bindings [1][2].
Quoted 8 lines
If there is no interest in taking the patch via OMAP tree, then it may go via the DT git tree. Rob, you should pick it up then.
Applying into omap-for-v5.17/dt thanks.
Regards,
Tony