hwmon: (lm90) Introduce flag indicating extended temperature support
Subsystems (3)
Guenter Roeck
maintainerPATCH v2 1/3 hwmon: (lm90) Introduce flag indicating extended temperature support
A flag indicating extended temperature support makes it easier to add support for additional chips with this functionality.
---
v2: Added patch
drivers/hwmon/lm90.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)
drivers/hwmon/lm90.c +11 -10
@@ -182,7 +182,8 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */ #define LM90_HAVE_TEMP3 (1 << 6)/* 3rd temperature sensor */ #define LM90_HAVE_BROKEN_ALERT (1 << 7)/* Broken alert */ -#define LM90_PAUSE_FOR_CONFIG (1 << 8)/* Pause conversion for config */ +#define LM90_HAVE_EXTENDED_TEMP (1 << 8)/* extended temperature support*/ +#define LM90_PAUSE_FOR_CONFIG (1 << 9)/* Pause conversion for config */ /* LM90 status */ #define LM90_STATUS_LTHRM (1 << 0)/* local THERM limit tripped */
@@ -350,7 +351,7 @@ static const struct lm90_params lm90_params[] = { }, [adt7461] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - | LM90_HAVE_BROKEN_ALERT, + | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP, .alert_alarms = 0x7c, .max_convrate = 10, },
@@ -422,7 +423,7 @@ static const struct lm90_params lm90_params[] = { }, [tmp451] = { .flags =LM90_HAVE_OFFSET |LM90_HAVE_REM_LIMIT_EXT - | LM90_HAVE_BROKEN_ALERT, + | LM90_HAVE_BROKEN_ALERT | LM90_HAVE_EXTENDED_TEMP, .alert_alarms = 0x7c, .max_convrate = 9, .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
@@ -998,7 +999,7 @@ static int lm90_get_temp11(struct lm90_data *data, int index)s16 temp11 = data->temp11[index];int temp; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u16_adt7461 (data, temp11);else if (data->kind == max6646) temp =temp_from_u16 (temp11);
@@ -1035,7 +1036,7 @@ static int lm90_set_temp11(struct lm90_data *data, int index, long val) val -=16000 ; } -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) data->temp11[index] =temp_to_u16_adt7461 (data, val);else if (data->kind == max6646) data->temp11[index] =temp_to_u8 (val) <<8 ;
@@ -1062,7 +1063,7 @@ static int lm90_get_temp8(struct lm90_data *data, int index)s8 temp8 = data->temp8[index];int temp; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u8_adt7461 (data, temp8);else if (data->kind == max6646) temp =temp_from_u8 (temp8);
@@ -1098,7 +1099,7 @@ static int lm90_set_temp8(struct lm90_data *data, int index, long val) val -=16000 ; } -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) data->temp8[index] =temp_to_u8_adt7461 (data, val);else if (data->kind == max6646) data->temp8[index] =temp_to_u8 (val);
@@ -1116,7 +1117,7 @@ static int lm90_get_temphyst(struct lm90_data *data, int index) {int temp; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u8_adt7461 (data, data->temp8[index]);else if (data->kind == max6646) temp =temp_from_u8 (data->temp8[index]);
@@ -1136,7 +1137,7 @@ static int lm90_set_temphyst(struct lm90_data *data, long val)int temp;int err; -if (data->kind == adt7461 || data->kind == tmp451) +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) temp =temp_from_u8_adt7461 (data, data->temp8[LOCAL_CRIT ]);else if (data->kind == max6646) temp =temp_from_u8 (data->temp8[LOCAL_CRIT ]);
@@ -1685,7 +1686,7 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)lm90_set_convrate (client, data,500 );/* 500ms; 2Hz conversion rate */ /* Check Temperature Range Select */ -if (data->kind == adt7461 || data->kind == tmp451) { +if (data->flags &LM90_HAVE_EXTENDED_TEMP ) {if (config &0x04 ) data->flags |=LM90_FLAG_ADT7461_EXT ; }
Signature · 1 line
2.33.0
Guenter Roeck
maintainerPATCH v2 2/3 hwmon: (lm90) Add basic support for TI TMP461
TMP461 is almost identical to TMP451 and was actually detected as TMP451 with the existing lm90 driver if its I2C address is 0x4c. Add support for it to the lm90 driver. At the same time, improve the chip detection function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations"). TMP461 does not support word operations on temperature registers, which causes bad temperature readings with the tmp401 driver. The lm90 driver does not perform word operations on temperature registers and thus does not have this problem.
Support is listed as basic because TMP461 supports a sensor resolution of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125 degrees C. Also, the TMP461 supports negative temperatures with its default temperature range, which is not the case for similar chips supported by the lm90 and the tmp401 drivers. Those limitations will be addressed with follow-up patches.
---
v2: Fixed DFC register address
Describe support as basic, and explain reason
Split introduction of LM90_HAVE_EXTENDED_TEMP into seperate patch
Documentation/hwmon/lm90.rst | 10 +++++++ drivers/hwmon/Kconfig | 2 +- drivers/hwmon/lm90.c | 54 ++++++++++++++++++++++++++---------- 3 files changed, 50 insertions(+), 16 deletions(-)
Documentation/hwmon/lm90.rst +10 -0
@@ -265,6 +265,16 @@ Supported chips: https://www.ti.com/litv/pdf/sbos686 + * Texas Instruments TMP461 + + Prefix: 'tmp461' + + Addresses scanned: I2C 0x48 through 0x4F + + Datasheet: Publicly available at TI website + + https://www.ti.com/lit/gpn/tmp461 + Author: Jean Delvare <[email protected]>
drivers/hwmon/Kconfig +1 -1
@@ -1317,7 +1317,7 @@ config SENSORS_LM90 Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658, MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG, - Philips SA56004, GMT G781, and Texas Instruments TMP451 + Philips SA56004, GMT G781, Texas Instruments TMP451 and TMP461 sensor chips. This driver can also be built as a module. If so, the module
drivers/hwmon/lm90.c +39 -15
100 lines not on this page · raw message
Signature · 1 line
2.33.0
Guenter Roeck
maintainerPATCH v2 3/3 hwmon: (tmp401) Drop support for TMP461
In reply to Guenter RoeckTMP461 is almost identical to TMP451, which is already supported by the lm90 driver. At the same time, unlike other sensors from the TMP401 compatible series, it only supports 8-bit temperature read operations, it supports negative temperatures when configured for its default temperature range, and it supports a temperature offset register. Supporting this chip in the tmp401 driver adds unnecessary complexity. Remove its support from this driver and support the chip with the lm90 driver instead.
---
v2: Explain additional limitations of tmp401 driver which are affecting
TMP461
Documentation/hwmon/tmp401.rst | 15 +-------------- drivers/hwmon/Kconfig | 2 +- drivers/hwmon/tmp401.c | 25 ++----------------------- 3 files changed, 4 insertions(+), 38 deletions(-)
Documentation/hwmon/tmp401.rst +1 -14
@@ -43,12 +43,6 @@ Supported chips: Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html - * Texas Instruments TMP461 - - Prefix: 'tmp461' - - Datasheet: https://www.ti.com/product/tmp461 - Authors:
@@ -60,7 +54,7 @@ Description ----------- This driver implements support for Texas Instruments TMP401, TMP411, -TMP431, TMP432, TMP435, and TMP461 chips. These chips implement one or two +TMP431, TMP432, and TMP435 chips. These chips implement one or two remote and one local temperature sensors. Temperature is measured in degrees Celsius. Resolution of the remote sensor is 0.0625 degree. Local sensor resolution can be set to 0.5, 0.25, 0.125 or 0.0625 degree (not
@@ -84,10 +78,3 @@ some additional features. TMP432 is compatible with TMP401 and TMP431. It supports two external temperature sensors. - -TMP461 is compatible with TMP401. It supports offset correction -that is applied to the remote sensor. - -* Sensor offset values are temperature values - - Exported via sysfs attribute tempX_offset
drivers/hwmon/Kconfig +1 -1
@@ -1930,7 +1930,7 @@ config SENSORS_TMP401 depends on I2C help If you say yes here you get support for Texas Instruments TMP401, - TMP411, TMP431, TMP432, TMP435, and TMP461 temperature sensor chips. + TMP411, TMP431, TMP432, and TMP435 temperature sensor chips. This driver can also be built as a module. If so, the module will be called tmp401.
drivers/hwmon/tmp401.c +2 -23
@@ -34,7 +34,7 @@static const unsigned short normal_i2c[] = {0x48 ,0x49 ,0x4a ,0x4c ,0x4d ,0x4e ,0x4f ,I2C_CLIENT_END }; -enum chips { tmp401, tmp411, tmp431, tmp432, tmp435, tmp461 }; +enum chips { tmp401, tmp411, tmp431, tmp432, tmp435 };/* * The TMP401 registers, note some registers have different addresses for
@@ -56,7 +56,6 @@ static const u8 TMP401_TEMP_MSB_READ[7][2] = { { 0x20, 0x19 }, /* therm (crit) limit */ { 0x30, 0x34 }, /* lowest */ { 0x32, 0x36 }, /* highest */ - { 0, 0x11 }, /* offset */ }; static const u8 TMP401_TEMP_MSB_WRITE[7][2] = {
@@ -66,7 +65,6 @@ static const u8 TMP401_TEMP_MSB_WRITE[7][2] = { { 0x20, 0x19 }, /* therm (crit) limit */ { 0x30, 0x34 }, /* lowest */ { 0x32, 0x36 }, /* highest */ - { 0, 0x11 }, /* offset */ }; static const u8 TMP432_TEMP_MSB_READ[4][3] = {
@@ -123,7 +121,6 @@ static const struct i2c_device_id tmp401_id[] = { { "tmp431", tmp431 }, { "tmp432", tmp432 }, { "tmp435", tmp435 }, - { "tmp461", tmp461 }, { } };MODULE_DEVICE_TABLE (i2c, tmp401_id);
@@ -570,21 +567,6 @@ static const struct attribute_group tmp432_group = { .attrs = tmp432_attributes, }; -/* -* Additional features of the TMP461 chip. -* The TMP461 temperature offset for the remote channel. -*/ -static SENSOR_DEVICE_ATTR_2_RW(temp2_offset, temp, 6, 1); - -static struct attribute *tmp461_attributes[] = { - &sensor_dev_attr_temp2_offset.dev_attr.attr, -NULL -}; - -static const struct attribute_group tmp461_group = { - .attrs = tmp461_attributes, -}; -/* * Begin non sysfs callback code (aka Real code) */
@@ -686,7 +668,7 @@ static int tmp401_detect(struct i2c_client *client,static int tmp401_probe (struct i2c_client *client) {static const char *const names[] = { -"TMP401" ,"TMP411" ,"TMP431" ,"TMP432" ,"TMP435" ,"TMP461" +"TMP401" ,"TMP411" ,"TMP431" ,"TMP432" ,"TMP435" };struct device *dev = &client->dev;struct device *hwmon_dev;
@@ -717,9 +699,6 @@ static int tmp401_probe(struct i2c_client *client)if (data->kind == tmp432) data->groups[groups++] = &tmp432_group; -if (data->kind == tmp461) - data->groups[groups++] = &tmp461_group; - hwmon_dev =devm_hwmon_device_register_with_groups (dev, client->name, data, data->groups);if (IS_ERR (hwmon_dev))
Signature · 1 line
2.33.0