ath11k: get msi_data again after request_irq is called

From: Carl Huang <[email protected]>

The reservation mode of interrupts in kernel assigns a dummy vector when the interrupt is allocated and assigns a real vector when the request_irq is called. The reservation mode helps to ease vector pressure when devices with a large amount of queues/interrupts are initialized, but only a minimal subset of those queues/interrupts is actually used.

So on reservation mode, the msi_data may change after request_irq is called, so ath11k reads msi_data again after request_irq is called, and then the correct msi_data is programmed into QCA6390 hardware components. Without this change, spurious interrupt occurs in case of one MSI vector. When VT-d in BIOS is enabled and ath11k can get 32 MSI vectors, ath11k always get the same msi_data before and after request_irq, that's why this change is only required when one MSI vector is to be supported.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

---
 drivers/net/wireless/ath/ath11k/pci.c | 30 +++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

index 3d353e7c9d5c..8691e1649d6c 100644
@@ -929,6 +929,25 @@ static void ath11k_pci_free_msi(struct ath11k_pci *ab_pci)
 	pci_free_irq_vectors(ab_pci->pdev);
 }
 
+static int ath11k_pci_config_msi_data(struct ath11k_pci *ab_pci)
+{
+	struct msi_desc *msi_desc;
+
+	msi_desc = irq_get_msi_desc(ab_pci->pdev->irq);
+	if (!msi_desc) {
+		ath11k_err(ab_pci->ab, "msi_desc is NULL!\n");
+		pci_free_irq_vectors(ab_pci->pdev);
+		return -EINVAL;
+	}
+
+	ab_pci->msi_ep_base_data = msi_desc->msg.data;
+
+	ath11k_dbg(ab_pci->ab, ATH11K_DBG_PCI, "pci after request_irq msi_ep_base_data %d\n",
+		   ab_pci->msi_ep_base_data);
+
+	return 0;
+}
+
 static int ath11k_pci_claim(struct ath11k_pci *ab_pci, struct pci_dev *pdev)
 {
 	struct ath11k_base *ab = ab_pci->ab;

@@ -1328,6 +1347,17 @@ static int ath11k_pci_probe(struct pci_dev *pdev,
 		goto err_ce_free;
 	}
 
+	/* kernel may allocate a dummy vector before request_irq and
+	 * then allocate a real vector when request_irq is called.
+	 * So get msi_data here again to avoid spurious interrupt
+	 * as msi_data will configured to srngs.
+	 */
+	ret = ath11k_pci_config_msi_data(ab_pci);
+	if (ret) {
+		ath11k_err(ab, "failed to config msi_data: %d\n", ret);
+		goto err_free_irq;
+	}
+
 	ret = ath11k_core_init(ab);
 	if (ret) {
 		ath11k_err(ab, "failed to init core: %d\n", ret);

2.25.1

7 patches applied to ath-next branch of ath.git, thanks.

87b4072d7ef8 ath11k: get msi_data again after request_irq is called 01279bcd01d9 ath11k: add CE and ext IRQ flag to indicate irq_handler 4ab4693f327a ath11k: use ATH11K_PCI_IRQ_DP_OFFSET for DP IRQ c41a6700b276 ath11k: refactor multiple MSI vector implementation ac6e73483f7b ath11k: add support one MSI vector
915a081ff307 ath11k: do not restore ASPM in case of single MSI vector e94b07493da3 ath11k: Set IRQ affinity to CPU0 in case of one MSI vector

https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches