Hi List,
i wrote a fbdev driver for the HP Visualize FX cards used some of the PA-RISC workstations. It utilizes some of the 2D acceleration features present in the card.
What is working right now:
- modesetting (tested all VESA modes between 640x480 - 1600x1200).
- hardware cursor
- 2D acceleration like imageblit and fillrect.
What is not (fully) working:
- X11 with fbdev. xinit + mwm looks almost ok, except some corruption where the text cursor was drawn when it is moved.
- more advanced X11 programs. xfce4-session doesn't really show much.
I would be most interested if people could test this driver with their FX cards and report. I know that Visualize FXe doesn't work because it uses completely different register addresses. For FX10 i would hope that they share the same register set as they are based on the same architecture. Note that you have to disable the sticon driver, otherwhise that one would hog the PCI card and visualizefx would never be probed.
Not sure about FX2/4/6. Might be different, might be not.
I obtained all the knowledge about the registers by watching what STI and the HP-UX X Server writes into the card. So the register names might be called different compared to what HP has written in their data books.
Sven.
PATCH 1/1 video: fbdev: add HP Visualize FX driver
This adds a framebuffer driver for HP's visualize series of cards. The aim is to support all FX2 - FX10 types but currently only FX5 is tested as i don't have any other card.
Currently no mmap of video memory is supported as i haven't figured out how to access VRAM directly.
--- drivers/video/fbdev/Kconfig | 14 + drivers/video/fbdev/Makefile | 2 +- drivers/video/fbdev/visualizefx.c | 602 ++++++++++++++++++++++++++++++ 3 files changed, 617 insertions(+), 1 deletion(-) create mode 100644 drivers/video/fbdev/visualizefx.c
drivers/video/fbdev/Kconfig +14 -0
@@ -566,6 +566,20 @@ config FB_STI It is safe to enable this option, so you should probably say "Y". +config FB_VISUALIZEFX + tristate "HP Visualize FX support" + depends on FB && PCI && PARISC + select FB_CFB_FILLRECT + select FB_CFB_COPYAREA + select FB_CFB_IMAGEBLIT + select RATIONAL + help + Frame buffer driver for the HP Visualize FX cards. These cards are + commonly found in PA-RISC workstations. Currently only FX5 has been + tested. + + Say Y if you have such a card. + config FB_MAC bool "Generic Macintosh display support" depends on (FB = y) && MAC
drivers/video/fbdev/Makefile +1 -1
@@ -129,6 +129,6 @@ obj-$(CONFIG_FB_MX3) += mx3fb.o obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o obj-$(CONFIG_FB_SIMPLE) += simplefb.o - +obj-$(CONFIG_FB_VISUALIZEFX) += visualizefx.o # the test framebuffer is last obj-$(CONFIG_FB_VIRTUAL) += vfb.o
drivers/video/fbdev/visualizefx.c new file +602 -0
602 lines not on this page · raw message
Signature · 1 line
2.33.0
Re: [PATCH] video: fbdev: add HP Visualize FX driver
Quoted 8 lines · Sven Schnelle
This adds a framebuffer driver for HP's visualize series of cards. The aim is to support all FX2 - FX10 types but currently only FX5 is tested as i don't have any other card.
Currently no mmap of video memory is supported as i haven't figured out how to access VRAM directly.
Signed-off-by Sven Schnelle <[email protected]>
That's really cool!
Quoted 12 lines
--- drivers/video/fbdev/Kconfig | 14 + drivers/video/fbdev/Makefile | 2 +- drivers/video/fbdev/visualizefx.c | 602 ++++++++++++++++++++++++++++++ 3 files changed, 617 insertions(+), 1 deletion(-) create mode 100644 drivers/video/fbdev/visualizefx.cdrivers/video/fbdev/Kconfig +0
-0
drivers/video/fbdev/Kconfig config FB_STI · line 575
Quoted 10 lines
drivers/video/fbdev/Kconfig +7
-0@@ -566,6 +566,20 @@ config FB_STI It is safe to enable this option, so you should probably say "Y". +config FB_VISUALIZEFX + tristate "HP Visualize FX support" + depends on FB && PCI && PARISC + select FB_CFB_FILLRECT + select FB_CFB_COPYAREA + select FB_CFB_IMAGEBLIT + select RATIONAL
You should add "default y", so that it automatically gets enabled on parisc machines:
default y
Other than that you may add an:
Thanks!
Helge
Quoted 631 lines
drivers/video/fbdev/Kconfig +7
-0+ help + Frame buffer driver for the HP Visualize FX cards. These cards are + commonly found in PA-RISC workstations. Currently only FX5 has been + tested. + + Say Y if you have such a card. + config FB_MAC bool "Generic Macintosh display support" depends on (FB = y) && MACdrivers/video/fbdev/Makefile +1
-1@@ -129,6 +129,6 @@ obj-$(CONFIG_FB_MX3) += mx3fb.o obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o obj-$(CONFIG_FB_SIMPLE) += simplefb.o - +obj-$(CONFIG_FB_VISUALIZEFX) += visualizefx.o # the test framebuffer is last obj-$(CONFIG_FB_VIRTUAL) += vfb.odrivers/video/fbdev/visualizefx.c new file +602
-0@@ -0,0 +1,602 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Framebuffer driver for Visualize FX cards commonly found in PA-RISC machines +* +* Copyright (c) 2021 Sven Schnelle <[email protected]> +*/ + +#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/pci.h> +#include <linux/fb.h> +#include <linux/delay.h> +#include <linux/rational.h> + +#define VISFX_VRAM_ENDIANESS_WRITE 0xa4303c +#define VISFX_VRAM_ENDIANESS_READ 0xaa0408 +#define VISFX_VRAM_ENDIANESS_BIG 0xe4e4e4e4 +#define VISFX_VRAM_ENDIANESS_LITTLE 0x1b1b1b1b + +#define VISFX_STATUS 0x641400 + +#define VISFX_COLOR_MASK 0x800018 +#define VISFX_COLOR_INDEX 0x800020 +#define VISFX_COLOR_VALUE 0x800024 + +#define VISFX_SYNC_POLARITY 0x800044 +#define VISFX_SYNC_VISIBLE_SIZE 0x80005c +#define VISFX_SYNC_HORIZ_CONF 0x800060 +#define VISFX_SYNC_VERT_CONF 0x800068 +#define VISFX_SYNC_MASTER_PLL 0x8000a0 +#define VISFX_SYNC_PLL_STATUS 0x8000b8 + +#define VISFX_VRAM_WRITE_MODE 0xa00808 +#define VISFX_VRAM_MASK 0xa0082c +#define VISFX_FGCOLOR 0xa0083c +#define VISFX_BGCOLOR 0xa00844 +#define VISFX_WRITE_MASK 0xa0084c +#define VISFX_VRAM_WRITE_DATA_INCRX 0xa60000 +#define VISFX_VRAM_WRITE_DATA_INCRY 0xa68000 +#define VISFX_SCREEN_SIZE 0xac1054 +#define VISFX_VRAM_WRITE_DEST 0xac1000 + +#define VISFX_START 0xb3c000 +#define VISFX_SIZE 0xb3c808 +#define VISFX_HEIGHT 0xb3c008 +#define VISFX_DST 0xb3cc00 + +#define VISFX_DFP_ENABLE 0x10000 +#define VISFX_HSYNC_POSITIVE 0x40000 +#define VISFX_VSYNC_POSITIVE 0x80000 + +#define VISFX_SYNC_PLL_BASE 49383/* 20.25MHz in ps */ + +#define VISFX_CURSOR_POS 0x400000 +#define VISFX_CURSOR_INDEX 0x400004 +#define VISFX_CURSOR_DATA 0x400008 +#define VISFX_CURSOR_COLOR 0x400010 +#define VISFX_CURSOR_ENABLE 0x80000000 + +#define VISFX_VRAM_WRITE_MODE_BITMAP 0x02000000 +#define VISFX_VRAM_WRITE_MODE_COLOR 0x050004c0 +#define VISFX_VRAM_WRITE_MODE_FILL 0x05000080 + +#define VISFX_FB_LENGTH 0x01000000 +#define VISFX_FB_OFFSET 0x01000000 +#define NR_PALETTE 256 + +struct visfx_par { +u32 pseudo_palette[256 ]; +unsigned long debug_reg; +void __iomem *reg_base; +unsigned long reg_size; +int open_count; +}; + +static u32 visfx_readl (struct fb_info *info,int reg) +{ +struct visfx_par *par = info->par; + +return le32_to_cpu (readl (par->reg_base + reg)); +} + +static void visfx_writel (struct fb_info *info,int reg,u32 val) +{ +struct visfx_par *par = info->par; + +return writel (cpu_to_le32 (val), par->reg_base + reg); +} + +static void visfx_write_vram (struct fb_info *info,int reg,u32 val) +{ +struct visfx_par *par = info->par; + +return writel (val, par->reg_base + reg); +} + +static void visfx_bmove_wait (struct fb_info *info) +{ +while (visfx_readl (info,VISFX_STATUS )); +} + +static ssize_t visfx_sysfs_show_reg (struct device *dev, +struct device_attribute *attr, +char *buf) +{ + struct fb_info *info = pci_get_drvdata(container_of(dev, struct pci_dev, dev)); +struct visfx_par *par = info->par; + +return sprintf (buf,"%08x\n" ,visfx_readl (info, par->debug_reg)); +} + +static ssize_t visfx_sysfs_store_reg (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ + struct fb_info *info = pci_get_drvdata(container_of(dev, struct pci_dev, dev)); +struct visfx_par *par = info->par; +unsigned long data; +char *p; + + p =strchr (buf,'=' ); +if (p) + *p ='\0' ; + +if (kstrtoul (buf,16 , &par->debug_reg)) +return -EINVAL ; + +if (par->debug_reg > par->reg_size) +return -EINVAL ; + +if (p) { +if (kstrtoul (p+1 ,16 , &data)) +return -EINVAL ; +visfx_writel (info, par->debug_reg, data); + } +return count; +} + +static DEVICE_ATTR(reg, 0600, visfx_sysfs_show_reg, visfx_sysfs_store_reg); + +static void visfx_set_vram_addr (struct fb_info *info,int x,int y) +{ +visfx_writel (info,VISFX_VRAM_WRITE_DEST , (y <<16 ) | x); +} + +static void visfx_set_bmove_color (struct fb_info *info,int fg,int bg) +{ +visfx_writel (info,VISFX_BGCOLOR ,0x01010101 * bg); +visfx_writel (info,VISFX_FGCOLOR ,0x01010101 * fg); +} + +static void visfx_imageblit_mono (struct fb_info *info,const char *data,int dx,int dy, +int width,int height,int fg_color,int bg_color) +{ +int _width, x, y; +u32 tmp; + +visfx_set_bmove_color (info, fg_color, bg_color); +visfx_writel (info,VISFX_VRAM_WRITE_MODE ,VISFX_VRAM_WRITE_MODE_COLOR ); +visfx_writel (info,VISFX_VRAM_MASK ,0xffffffff ); + +for (x =0 , _width = width; _width >0 ; _width -=32 , x +=4 ) { +visfx_set_vram_addr (info, dx + x *8 , dy); +if (_width >=32 ) { +for (y =0 ; y < height; y++) { +memcpy (&tmp, &data[y * (width /8 ) + x],4 ); +visfx_write_vram (info,VISFX_VRAM_WRITE_DATA_INCRY , tmp); + } + }else { +visfx_writel (info,VISFX_VRAM_MASK ,GENMASK (31 ,31 - _width +1 )); +for (y =0 ; y < height; y++) { + tmp =0 ; +memcpy (&tmp, &data[y * (width /8 ) + x], ((_width-1 )/8 )+1 ); +visfx_write_vram (info,VISFX_VRAM_WRITE_DATA_INCRY , tmp); + } + } + } +} + +static void visfx_setup_unknown (struct fb_info *info) +{ +visfx_writel (info,0xb08044 ,0x1b ); +visfx_writel (info,0xb08048 ,0x1b ); +visfx_writel (info,0x920860 ,0xe4 ); +visfx_writel (info,0xa00818 ,0 ); +visfx_writel (info,0xa00404 ,0 ); +visfx_writel (info,0x921110 ,0 ); +visfx_writel (info,0x9211d8 ,0 ); +visfx_writel (info,0xa0086c ,0 ); +visfx_writel (info,0x921114 ,0 ); +visfx_writel (info,0xac1050 ,0 ); +visfx_writel (info,0xa00858 ,0xb0 ); + +visfx_writel (info,VISFX_VRAM_WRITE_MODE ,VISFX_VRAM_WRITE_MODE_BITMAP ); +visfx_writel (info,VISFX_WRITE_MASK ,0xffffffff ); +visfx_writel (info,VISFX_VRAM_MASK ,0xffffffff ); +#ifdef __BIG_ENDIAN +visfx_writel (info,VISFX_VRAM_ENDIANESS_READ ,VISFX_VRAM_ENDIANESS_BIG ); +visfx_writel (info,VISFX_VRAM_ENDIANESS_WRITE ,VISFX_VRAM_ENDIANESS_BIG ); +#else +visfx_writel (info,VISFX_VRAM_ENDIANESS_READ ,VISFX_VRAM_ENDIANESS_LITTLE ); +visfx_writel (info,VISFX_VRAM_ENDIANESS_WRITE ,VISFX_VRAM_ENDIANESS_LITTLE ); +#endif +} + +static void visfx_imageblit (struct fb_info *info,const struct fb_image *image) +{ +int x, y; + +visfx_bmove_wait (info); +visfx_writel (info,VISFX_WRITE_MASK ,0xffffffff ); + +switch (image->depth) { +case 1 : +visfx_imageblit_mono (info, image->data, image->dx, image->dy, + image->width, image->height, + image->fg_color, image->bg_color); +break ; +case 8 : +visfx_writel (info,VISFX_VRAM_WRITE_MODE ,VISFX_VRAM_WRITE_MODE_BITMAP ); + +for (y =0 ; y < image->height; y++) { +u32 data =0 ; +int pos =0 ; + +visfx_writel (info,VISFX_WRITE_MASK ,0xffffffff ); +visfx_set_vram_addr (info, image->dx, image->dy + y); + +for (x =0 ; x < image->width; x++) { + pos = x &3 ; + data |= ((u8 *)image->data)[y * image->height + x] << (pos *8 ); +if (pos ==3 ) { +visfx_write_vram (info,VISFX_VRAM_WRITE_DATA_INCRX , data); + data =0 ; + } + } + +if (x && pos !=3 ) { +visfx_write_vram (info,VISFX_WRITE_MASK , (1 << ((pos+1 ) *8 ))-1 ); +visfx_write_vram (info,VISFX_VRAM_WRITE_DATA_INCRX , data); + } + } +break ; + +default : +break ; + } +} + +static void visfx_fillrect (struct fb_info *info,const struct fb_fillrect *fr) +{ +visfx_bmove_wait (info); +visfx_writel (info,VISFX_WRITE_MASK ,0xffffffff ); +visfx_writel (info,VISFX_VRAM_WRITE_MODE ,VISFX_VRAM_WRITE_MODE_FILL ); +visfx_set_bmove_color (info, fr->color,0 ); +visfx_writel (info,VISFX_START , (fr->dx <<16 ) | fr->dy); +visfx_writel (info,VISFX_SIZE , (fr->width <<16 ) | fr->height); +} + +static u32 visfx_cmap_entry (struct fb_cmap *cmap,int color) +{ +return (((cmap->blue[color] &0xff )) | + ((cmap->green[color] &0xff ) <<8 ) | + (cmap->red[color] &0xff ) <<16 ); +} + +static int visfx_setcmap (struct fb_cmap *cmap,struct fb_info *info) +{ +int i; + +visfx_writel (info,VISFX_COLOR_INDEX , cmap->start); + +for (i =0 ; i < cmap->len; i++) +visfx_writel (info,VISFX_COLOR_VALUE ,visfx_cmap_entry (cmap, i)); + +visfx_writel (info,VISFX_COLOR_MASK ,0xff ); +visfx_writel (info,0x80004c ,0xc ); +visfx_writel (info,0x800000 ,0 ); +return 0 ; +} + +static void visfx_get_video_mode (struct fb_info *info) +{ +struct fb_var_screeninfo *var = &info->var; +unsigned long n, d; +u32 tmp; + + tmp =visfx_readl (info,VISFX_SYNC_VISIBLE_SIZE ); + var->xres = (tmp &0xffff ) +1 ; + var->yres = (tmp >>16 ) +1 ; + + tmp =visfx_readl (info,VISFX_SYNC_MASTER_PLL ); + n = (tmp &0xff ) +1 ; + d = ((tmp >>8 ) &0xff ) +1 ; + var->pixclock = (VISFX_SYNC_PLL_BASE / d) * n; + + tmp =visfx_readl (info,VISFX_SYNC_HORIZ_CONF ); + var->left_margin = ((tmp >>20 ) &0x1ff ) +1 ; + var->hsync_len = (((tmp >>12 ) &0xff ) +1 ) *4 ; + var->right_margin = (tmp &0x1ff ) +1 ; + + tmp =visfx_readl (info,VISFX_SYNC_VERT_CONF ); + var->upper_margin = ((tmp >>16 ) &0xff ) +1 ; + var->vsync_len = ((tmp >>8 ) &0xff ) +1 ; + var->lower_margin = (tmp &0xff ) +1 ; + + tmp =visfx_readl (info,VISFX_SYNC_POLARITY ); +if (tmp &VISFX_HSYNC_POSITIVE ) + var->sync |=FB_SYNC_HOR_HIGH_ACT ; +if (tmp &VISFX_VSYNC_POSITIVE ) + var->sync |=FB_SYNC_VERT_HIGH_ACT ; + + var->red.length =8 ; + var->green.length =8 ; + var->blue.length =8 ; + var->bits_per_pixel =8 ; + var->grayscale =0 ; + var->xres_virtual = var->xres; + var->yres_virtual = var->yres; + info->screen_size =2048 * var->yres; +} + +static void visfx_set_pll (struct fb_info *info,unsigned long clock) +{ +unsigned long n, d, tmp; + +rational_best_approximation (clock,VISFX_SYNC_PLL_BASE ,0x3f ,0x3f , &n, &d); + tmp = (((d *4 ) -1 ) <<8 ) | ((n *4 ) -1 ); +visfx_writel (info,VISFX_SYNC_MASTER_PLL ,0x520000 | tmp); +while (visfx_readl (info,VISFX_SYNC_PLL_STATUS ) &0xffffff ) +udelay (10 ); +visfx_writel (info,VISFX_SYNC_MASTER_PLL ,0x530000 | tmp); +while (visfx_readl (info,VISFX_SYNC_PLL_STATUS ) &0xffffff ) +udelay (10 ); +} + +static int visfx_set_par (struct fb_info *info) +{ +u32 xres, yres, hbp, hsw, hfp, vbp, vsw, vfp, tmp; +struct fb_var_screeninfo *var = &info->var; + + + xres = var->xres; + yres = var->yres; + hsw = var->hsync_len /4 -1 ; + hfp = var->right_margin -1 ; + hbp = var->left_margin -1 ; + vsw = var->vsync_len -1 ; + vfp = var->lower_margin -1 ; + vbp = var->upper_margin -1 ; + +visfx_set_pll (info, var->pixclock); +visfx_writel (info,VISFX_SYNC_VISIBLE_SIZE , ((yres -1 ) <<16 ) | (xres -1 )); +visfx_writel (info,VISFX_SYNC_HORIZ_CONF , (hbp <<20 ) | (hsw <<12 ) | (0xc <<8 ) | hfp); +visfx_writel (info,VISFX_SYNC_VERT_CONF , (vbp <<16 ) | (vsw <<8 ) | vfp); +visfx_writel (info,VISFX_SCREEN_SIZE , (xres <<16 ) | yres); + + tmp =VISFX_DFP_ENABLE ; +if (var->sync &FB_SYNC_HOR_HIGH_ACT ) + tmp |=VISFX_HSYNC_POSITIVE ; +if (var->sync &FB_SYNC_VERT_HIGH_ACT ) + tmp |=VISFX_VSYNC_POSITIVE ; +visfx_writel (info,VISFX_SYNC_POLARITY , tmp); + +visfx_writel (info,VISFX_VRAM_WRITE_MODE ,VISFX_VRAM_WRITE_MODE_BITMAP ); + +visfx_get_video_mode (info); +return 0 ; +} + +static int visfx_check_var (struct fb_var_screeninfo *var,struct fb_info *info) +{ +if (var->pixclock >VISFX_SYNC_PLL_BASE || + var->left_margin >512 || + var->right_margin >512 || + var->hsync_len >512 || + var->lower_margin >256 || + var->upper_margin >256 || + var->vsync_len >256 || + var->xres >2048 || + var->yres >2048 ) +return -EINVAL ; +return 0 ; +} + +static void visfx_update_cursor_image_line (struct fb_info *info, +struct fb_cursor *cursor,int y) +{ +unsigned int x, bytecnt; +u32 data[2 ] = {0 }; +u8 d, m; + + bytecnt = cursor->image.width /8 ; + +for (x =0 ; x < bytecnt && x <8 ; x++) { + m = cursor->mask[y * bytecnt + x]; + d = cursor->image.data[y * bytecnt + x]; + +if (cursor->rop ==ROP_XOR ) + ((u8 *)data)[x] = d ^ m; +else + ((u8 *)data)[x] = d & m; + } + +visfx_writel (info,VISFX_CURSOR_DATA , data[0 ]); +visfx_writel (info,VISFX_CURSOR_DATA , data[1 ]); +} + +static void visfx_update_cursor_image (struct fb_info *info, +struct fb_cursor *cursor) +{ +int y, height = cursor->image.height; + +if (height >128 ) + height =128 ; + +visfx_writel (info,VISFX_CURSOR_INDEX ,0 ); +for (y =0 ; y < height; y++) +visfx_update_cursor_image_line (info, cursor, y); + +for (; y <256 ; y++) +visfx_writel (info,VISFX_CURSOR_DATA ,0 ); +} + +static int visfx_cursor (struct fb_info *info,struct fb_cursor *cursor) +{ +u32 tmp; + +if (cursor->set & (FB_CUR_SETIMAGE |FB_CUR_SETSHAPE )) +visfx_update_cursor_image (info, cursor); + +if (cursor->set &FB_CUR_SETCMAP ) { + tmp =visfx_cmap_entry (&info->cmap, cursor->image.fg_color); +visfx_writel (info,VISFX_CURSOR_COLOR , tmp); + } + + tmp = (cursor->image.dx <<16 ) | (cursor->image.dy &0xffff ); +if (cursor->enable) + tmp |=VISFX_CURSOR_ENABLE ; +visfx_writel (info,VISFX_CURSOR_POS , tmp); +return 0 ; +} + +static int visfx_open (struct fb_info *info,int user) +{ +struct visfx_par *par = info->par; + +if (user && par->open_count++ ==0 ) +visfx_writel (info,VISFX_VRAM_WRITE_MODE ,VISFX_VRAM_WRITE_MODE_BITMAP ); + +return 0 ; +} + +static int visfx_release (struct fb_info *info,int user) +{ +struct visfx_par *par = info->par; + +if (user) + par->open_count--; + +return 0 ; +} + +static const struct fb_ops visfx_ops = { + .owner =THIS_MODULE , + .fb_open = visfx_open, + .fb_release = visfx_release, + .fb_setcmap = visfx_setcmap, + .fb_fillrect = visfx_fillrect, + .fb_imageblit = visfx_imageblit, + .fb_set_par = visfx_set_par, + .fb_check_var = visfx_check_var, + .fb_cursor = visfx_cursor, +}; + +static struct fb_fix_screeninfo visfx_fix = { + .type =FB_TYPE_PACKED_PIXELS , + .visual =FB_VISUAL_PSEUDOCOLOR , + .id ="Visualize FX" , +}; + +static int visfx_probe (struct pci_dev *pdev, +const struct pci_device_id *ent) +{ +struct visfx_par *par; +struct fb_info *info; +int ret; + + info =framebuffer_alloc (sizeof (struct visfx_par ), &pdev->dev); +if (!info) +return -ENOMEM ; + + par = info->par; + + ret =pci_enable_device (pdev); +if (ret) + goto err_out_free; + + ret =pci_request_regions (pdev,KBUILD_MODNAME ); +if (ret) + goto err_out_disable; + + par->reg_size =pci_resource_len (pdev,0 ); + par->reg_base =pci_ioremap_bar (pdev,0 ); + par->open_count =0 ; + +if (!par->reg_base) { + ret = -ENOMEM ; + goto err_out_release; + } + +pci_set_drvdata (pdev, info); + + info->fbops = &visfx_ops; + info->flags =FBINFO_DEFAULT |FBINFO_HWACCEL_FILLRECT |FBINFO_HWACCEL_IMAGEBLIT ; + info->fix = visfx_fix; + info->pseudo_palette = par->pseudo_palette; + info->fix.smem_start =pci_resource_start (pdev,0 ) +VISFX_FB_OFFSET ; + info->fix.smem_len =VISFX_FB_LENGTH ; + info->screen_base = par->reg_base +VISFX_FB_OFFSET ; + info->fix.type =FB_TYPE_PACKED_PIXELS ; + info->fix.visual =FB_VISUAL_PSEUDOCOLOR ; + info->fix.line_length =2048 ; + info->fix.accel =FB_ACCEL_NONE ; + +visfx_setup_unknown (info); +visfx_get_video_mode (info); + info->var.accel_flags = info->flags; + + ret =device_create_file (&pdev->dev, &dev_attr_reg); +if (ret) + goto err_out_iounmap; + + ret =fb_alloc_cmap (&info->cmap,NR_PALETTE ,0 ); +if (ret) + goto err_out_remove; + + ret =register_framebuffer (info); +if (ret) + goto err_out_dealloc_cmap; +return 0 ; + +err_out_dealloc_cmap: +fb_dealloc_cmap (&info->cmap); +err_out_remove: +device_remove_file (&pdev->dev, &dev_attr_reg); +err_out_iounmap: +pci_iounmap (pdev, par->reg_base); +err_out_release: +pci_release_regions (pdev); +err_out_disable: +pci_disable_device (pdev); +err_out_free: +framebuffer_release (info); +return ret; +} + +static void __exit visfx_remove(struct pci_dev *pdev) +{ +struct fb_info *info =pci_get_drvdata (pdev); +struct visfx_par *par = info->par; + +device_remove_file (&pdev->dev, &dev_attr_reg); +unregister_framebuffer (info); +pci_iounmap (pdev, par->reg_base); +framebuffer_release (info); +pci_release_regions (pdev); +pci_disable_device (pdev); +} + +static const struct pci_device_id visfx_pci_tbl[] = { + {PCI_DEVICE (PCI_VENDOR_ID_HP ,0x1008 ) }, + {0 }, +}; +MODULE_DEVICE_TABLE (pci, visfx_pci_tbl); + +static struct pci_driver visfx_driver = { + .name =KBUILD_MODNAME , + .id_table = visfx_pci_tbl, + .probe = visfx_probe, + .remove = visfx_remove, +}; + +static int __init visfx_init (void ) +{ +return pci_register_driver (&visfx_driver); +} +module_init (visfx_init); + +static void __exit visfx_exit(void) +{ +pci_unregister_driver (&visfx_driver); +} +module_exit (visfx_exit); + +MODULE_AUTHOR ("Sven Schnelle <[email protected]>" ); +MODULE_DESCRIPTION ("Framebuffer driver for HP Visualize FX cards" ); +MODULE_LICENSE ("GPL" );
Re: [PATCH] video: fbdev: add HP Visualize FX driver
In reply to Sven SchnelleAm Sonntag, 31. Oktober 2021, 21:49:52 CET schrieb Sven Schnelle:
Quoted 6 lines
This adds a framebuffer driver for HP's visualize series of cards. The aim is to support all FX2 - FX10 types but currently only FX5 is tested as i don't have any other card.
Currently no mmap of video memory is supported as i haven't figured out how to access VRAM directly.
Besides the DRM things here are a few more things I spotted.
Quoted 1 line
+struct
visfx_par{
What is "par"? Maybe a little more descriptive name would help, _param or something?
drivers/video/fbdev/visualizefx.c line 78
Quoted 6 lines
drivers/video/fbdev/visualizefx.c new file +6
-0+u32 pseudo_palette[256 ]; +unsigned long debug_reg; +void __iomem *reg_base; +unsigned long reg_size; +int open_count; +};
I would move the more often used members to the top, that should make accesses of the often used members slightly more efficient as there is no offset needed.
drivers/video/fbdev/visualizefx.c
Quoted 5 lines
drivers/video/fbdev/visualizefx.c new file +5
-0+static ssize_t visfx_sysfs_show_reg (struct device *dev, +struct device_attribute *attr, +char *buf) +{ + struct fb_info *info = pci_get_drvdata(container_of(dev, struct
pci_dev,
drivers/video/fbdev/visualizefx.c
Quoted 7 lines
dev)); + struct
visfx_par*par =info->par;drivers/video/fbdev/visualizefx.c new file +6
-0+ +return sprintf (buf,"%08x\n" ,visfx_readl (info, par->debug_reg)); +} + +static ssize_t visfx_sysfs_store_reg (struct device *dev, + struct device_attribute
*attr,
Review
Quoted 1 line
(quoted diff) +1
-0+ const char *buf, size_t
count)
Review
Quoted 2 lines
(quoted diff) +2
-0+{ + struct fb_info *info = pci_get_drvdata(container_of(dev, struct
pci_dev,
drivers/video/fbdev/visualizefx.c line 127
Quoted 7 lines
dev)); + struct
visfx_par*par =info->par;drivers/video/fbdev/visualizefx.c new file +6
-0+unsigned long data; +char *p; + + p =strchr (buf,'=' ); +if (p) + *p ='\0' ;
No -EINVAL without '='?
drivers/video/fbdev/visualizefx.c line 136
Quoted 8 lines
drivers/video/fbdev/visualizefx.c new file +8
-0+if (kstrtoul (buf,16 , &par->debug_reg)) +return -EINVAL ; + +if (par->debug_reg > par->reg_size) +return -EINVAL ; + +if (p) { +if (kstrtoul (p+1 ,16 , &data))
Spaces around +
drivers/video/fbdev/visualizefx.c line 143
Quoted 7 lines
drivers/video/fbdev/visualizefx.c new file +7
-0+return -EINVAL ; +visfx_writel (info, par->debug_reg, data); + } +return count; +} + +static DEVICE_ATTR(reg, 0600, visfx_sysfs_show_reg, visfx_sysfs_store_reg);
Sysfs API is public API, so it needs to be documented and such. Also I bet there are helpers to do this better. But I think this should be debugfs attributes, not sysfs ones.
Quoted 2 lines
+static void visfx_imageblit_mono(struct
fb_info*info, const char *data,
int dx, int dy, + int width, int
height, int fg_color, int bg_color)
Review
Quoted 2 lines
(quoted diff) +2
-0+{ + int _width, x, y;
Having variables named width and _width is just asking for future trouble IMHO. Maybe just call the local one "w" or something.
Review
Quoted 1 line
(quoted diff) +1
-0+ u32 tmp;
You can move that into a more local scope to make it more obvious it doesn't carry and state between loop iterations.
Review
Quoted 2 lines
(quoted diff) +2
-0+ visfx_set_bmove_color(info, fg_color, bg_color); + visfx_writel(info, VISFX_VRAM_WRITE_MODE,
VISFX_VRAM_WRITE_MODE_COLOR);
drivers/video/fbdev/visualizefx.c
Quoted 7 lines
drivers/video/fbdev/visualizefx.c new file +7
-0+ visfx_writel(info, VISFX_VRAM_MASK, 0xffffffff); + + for (x = 0, _width = width; _width > 0; _width -= 32, x += 4) { + visfx_set_vram_addr(info, dx + x * 8, dy); + if (_width >= 32) { + for (y = 0; y < height; y++) { + memcpy(&tmp, &data[y * (width / 8)
+ x], 4);
Review
Quoted 1 line
(quoted diff) +1
-0+ visfx_write_vram(info,
VISFX_VRAM_WRITE_DATA_INCRY, tmp);
drivers/video/fbdev/visualizefx.c
Quoted 3 lines
drivers/video/fbdev/visualizefx.c new file +3
-0+ } + }else { + visfx_writel(info, VISFX_VRAM_MASK,
GENMASK(31, 31 - _width + 1));
drivers/video/fbdev/visualizefx.c
Quoted 3 lines
drivers/video/fbdev/visualizefx.c new file +3
-0+ for (y = 0; y < height; y++) { + tmp = 0; + memcpy(&tmp, &data[y * (width / 8)
+ x], ((_width-1)/8)+1);
Review
Quoted 1 line
(quoted diff) +1
-0+ visfx_write_vram(info,
VISFX_VRAM_WRITE_DATA_INCRY, tmp);
Quoted 8 lines
drivers/video/fbdev/visualizefx.c new file +8
-0+ } + } + } +} + +static void visfx_setup_unknown (struct fb_info *info) +{ +visfx_writel (info,0xb08044 ,0x1b );
drivers/video/fbdev/visualizefx.c line 196
Quoted 10 lines
drivers/video/fbdev/visualizefx.c new file +10
-0+visfx_writel (info,0xb08048 ,0x1b ); +visfx_writel (info,0x920860 ,0xe4 ); +visfx_writel (info,0xa00818 ,0 ); +visfx_writel (info,0xa00404 ,0 ); +visfx_writel (info,0x921110 ,0 ); +visfx_writel (info,0x9211d8 ,0 ); +visfx_writel (info,0xa0086c ,0 ); +visfx_writel (info,0x921114 ,0 ); +visfx_writel (info,0xac1050 ,0 ); +visfx_writel (info,0xa00858 ,0xb0 );
A little comment about these numbers would be good, even if it is just "recorded from HP-UX driver, no idea what it does".
drivers/video/fbdev/visualizefx.c line 386
Quoted 12 lines
+static int
visfx_check_var(struct fb_var_screeninfo *var, struct fb_info *info)+{drivers/video/fbdev/visualizefx.c new file +10
-0+if (var->pixclock >VISFX_SYNC_PLL_BASE || + var->left_margin >512 || + var->right_margin >512 || + var->hsync_len >512 || + var->lower_margin >256 || + var->upper_margin >256 || + var->vsync_len >256 || + var->xres >2048 || + var->yres >2048 ) +return -EINVAL ;
Something went wrong with the indentation here.
drivers/video/fbdev/visualizefx.c line 463
Quoted 6 lines
drivers/video/fbdev/visualizefx.c new file +6
-0+static int visfx_release (struct fb_info *info,int user) +{ +struct visfx_par *par = info->par; + +if (user) + par->open_count--;
Check for underflow, just out of paranoia?
drivers/video/fbdev/visualizefx.c line 493
Quoted 8 lines
drivers/video/fbdev/visualizefx.c new file +8
-0+static int visfx_probe (struct pci_dev *pdev, +const struct pci_device_id *ent) +{ +struct visfx_par *par; +struct fb_info *info; +int ret; + + info =framebuffer_alloc (sizeof (struct visfx_par ), &pdev->dev);
sizeof(*par)
drivers/video/fbdev/visualizefx.c line 499
Quoted 6 lines
drivers/video/fbdev/visualizefx.c new file +6
-0+if (!info) +return -ENOMEM ; + + par = info->par; + + ret =pci_enable_device (pdev);
If you don't have a really good reason to do so you should used pcim_enable_device(), which will do half of the following error cleanups and the remove handling for you.
drivers/video/fbdev/visualizefx.c line 598
Quoted 11 lines
drivers/video/fbdev/visualizefx.c new file +11
-0+static int __init visfx_init (void ) +{ +return pci_register_driver (&visfx_driver); +} +module_init (visfx_init); + +static void __exit visfx_exit(void) +{ +pci_unregister_driver (&visfx_driver); +} +module_exit (visfx_exit);
module_pci_driver(&visfx_driver);
Greetings,
Eike