Skip to contentSkip to conversation

ARM: dts: stm32: Synchronize DHCOR DTs with Linux 5.15.12

PATCH In review Marek Vasut 3 participants 7 messages Dec 30, 2021 – Jan 24, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 ARM: dts: stm32: Synchronize DHCOR DTs with Linux 5.15.12

Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias is now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96 u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
 arch/arm/dts/Makefile                         |   1 -
 arch/arm/dts/stm32mp157a-avenger96.dts        |   8 -
 arch/arm/dts/stm32mp157a-dhcor-avenger96.dts  |  38 ++
 .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi   |   2 +
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts  | 202 +-------
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi | 431 ++++++++++++++++++
 arch/arm/dts/stm32mp15xx-dhcor-io1v8.dtsi     |   7 +-
 ...-io3v3.dtsi => stm32mp15xx-dhcor-som.dtsi} |  30 +-
 arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi    |   8 +
 9 files changed, 503 insertions(+), 224 deletions(-)
 delete mode 100644 arch/arm/dts/stm32mp157a-avenger96.dts
 create mode 100644 arch/arm/dts/stm32mp157a-dhcor-avenger96.dts
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi
 rename arch/arm/dts/{stm32mp15xx-dhcor-io3v3.dtsi => stm32mp15xx-dhcor-som.dtsi} (91%)
arch/arm/dts/Makefile +0 -1
index b3e2a9c9d77..03064632999 100644
@@ -1098,7 +1098,6 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 
 dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-dk1.dtb \
-	stm32mp157a-avenger96.dtb \
 	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
 	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
 	stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
arch/arm/dts/stm32mp157a-avenger96.dts deleted +0 -8
deleted file mode 100644
index 9c165104fbe..00000000000
@@ -1,8 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <[email protected]>
- */
-
-/* This is kept for backward compatibility and will be removed */
-#include "stm32mp15xx-dhcor-avenger96.dts"
arch/arm/dts/stm32mp157a-dhcor-avenger96.dts new file +38 -0
new file mode 100644
index 00000000000..2e3c9fbb4eb
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * Avenger96 PCB number: 588-200 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP157A Avenger96 board";
+	compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som",
+		     "st,stm32mp157";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "disabled";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "disabled";
+};
arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi +2 -0
index c96eba99c5e..6e6543b5e4a 100644
@@ -21,6 +21,8 @@
 
 
 &ethernet0 {
+	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+
 	mdio0 {
 		ethernet-phy@7 {
 			reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts +4 -198

210 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi new file +431 -0

431 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcor-io1v8.dtsi +3 -4
index 75435424d67..75172314d7a 100644
@@ -1,12 +1,12 @@
 // SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
 /*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
 
-#include "stm32mp15xx-dhcor-io3v3.dtsi"
-
 / {
-	/* Enpirion EP3A8LQI U2 on the 1V8 IO DHCOR */
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
 	vdd_io: regulator-buck-io {
 		compatible = "regulator-fixed";
 		regulator-name = "buck-io";
@@ -20,5 +20,4 @@
 
 &pwr_regulators {
 	vdd-supply = <&vdd_io>;
-	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
arch/arm/dts/stm32mp15xx-dhcor-som.dtsi renamed from arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi +17 -13
similarity index 91%
rename from arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcor-som.dtsi
index 94cf80dbede..44ecc470858 100644
@@ -4,9 +4,7 @@
  * Author: Manivannan Sadhasivam <[email protected]>
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
-/dts-v1/;
 
-#include "stm32mp157.dtsi"
 #include "stm32mp15-pinctrl.dtsi"
 #include "stm32mp15xxac-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
@@ -23,6 +21,14 @@
 	};
 };
 
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
 &i2c4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c4_pins_a>;
@@ -35,7 +41,7 @@
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
-		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		status = "okay";
@@ -53,7 +59,7 @@
 
 			vddcore: buck1 {
 				regulator-name = "vddcore";
-				regulator-min-microvolt = <800000>;
+				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
@@ -92,7 +98,6 @@
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO1 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			v2v8: ldo2 {
@@ -100,7 +105,6 @@
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
 				interrupts = <IT_CURLIM_LDO2 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vtt_ddr: ldo3 {
@@ -114,7 +118,6 @@
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
 				interrupts = <IT_CURLIM_LDO4 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vdd_sd: ldo5 {
@@ -122,7 +125,6 @@
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO5 0>;
-				interrupt-parent = <&pmic>;
 				regulator-boot-on;
 			};
 
@@ -131,7 +133,6 @@
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				interrupts = <IT_CURLIM_LDO6 0>;
-				interrupt-parent = <&pmic>;
 				regulator-enable-ramp-delay = <300000>;
 			};
 
@@ -143,20 +144,17 @@
 			bst_out: boost {
 				regulator-name = "bst_out";
 				interrupts = <IT_OCP_BOOST 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				interrupt-parent = <&pmic>;
 				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				interrupt-parent = <&pmic>;
 				regulator-active-discharge = <1>;
 			};
 		};
@@ -173,6 +171,12 @@
 			status = "disabled";
 		};
 	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
 };
 
 &iwdg2 {
@@ -194,7 +198,7 @@
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: spi-flash@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi +8 -0
index 71375510b4a..338b674368a 100644
@@ -15,6 +15,11 @@
 
 / {
 	u-boot,dm-pre-reloc;
+
+	aliases {
+		eeprom0 = &eeprom0;
+	};
+
 	config {
 		dh,ddr3-coding-gpios = <&gpiog 0 0>, <&gpiog 1 0>;
 		dh,som-coding-gpios = <&gpioz 7 0>, <&gpiof 3 0>;
@@ -28,6 +33,9 @@
 &i2c4 {
 	u-boot,dm-pre-reloc;
 	u-boot,dm-spl;
+
+	eeprom0: eeprom@53 {
+	};
 };
 
 &i2c4_pins_a {
Signature · 1 line
2.34.1
#1 lore raw

PATCH 2/2 ARM: dts: stm32: Synchronize DHCOM DTs with Linux 5.15.12

Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias and PHY reset GPIO are now reinstated in SoM u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
 arch/arm/dts/stm32mp15xx-dhcom-drc02.dts      | 162 +-------
 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi     | 165 ++++++++
 .../dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi    |   4 +
 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts       |  14 +-
 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi      | 325 +++++++++++++++
 .../dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi |   6 +-
 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts    |  88 +---
 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi   | 147 +++++++
 ...-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} | 387 +++++++++++-------
 arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi    |  43 +-
 10 files changed, 917 insertions(+), 424 deletions(-)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi
 rename arch/arm/dts/{stm32mp15xx-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} (56%)
arch/arm/dts/stm32mp15xx-dhcom-drc02.dts +5 -157
index 4948ccd4014..1ef9ac29cea 100644
@@ -2,166 +2,14 @@
 /*
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
 
 / {
 	model = "DH Electronics STM32MP15xx DHCOM DRC02";
 	compatible = "dh,stm32mp15xx-dhcom-drc02", "st,stm32mp1xx";
-
-	aliases {
-		serial0 = &uart4;
-		serial1 = &usart3;
-		serial2 = &uart8;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&adc {
-	status = "disabled";
-};
-
-&dac {
-	status = "disabled";
-};
-
-&gpiob {
-	/*
-	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
-	 * GPIO line, however the STM32 UART driver assumes RX happens
-	 * during TX anyway and that it only controls drive enable DE
-	 * line. Hence, the RX is always enabled here.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <8 0>;
-		output-high;
-		line-name = "rs485-rx-en";
-	};
-};
-
-&gpiod {
-	gpio-line-names = "", "", "", "",
-			  "", "", "", "",
-			  "", "", "", "Out1",
-			  "Out2", "", "", "";
-};
-
-&gpioi {
-	gpio-line-names = "In1", "", "", "",
-			  "", "", "", "",
-			  "In2", "", "", "",
-			  "", "", "", "";
-
-	/*
-	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
-	 * pulled high in order to be detected by the USB Controller.
-	 * This signal should be handled by USB power sequencing in
-	 * order to reset the Hub when USB bus is powered down, but
-	 * so far there is no such functionality.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <2 0>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c04";
-		reg = <0x50>;
-		pagesize = <16>;
-	};
-};
-
-&i2c5 {	/* TP7/TP8 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&sdmmc3 {
-	/*
-	 * On DRC02, the SoM does not have SDIO WiFi. The pins
-	 * are used for on-board microSD slot instead.
-	 */
-	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc3_b4_pins_a>;
-	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
-	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
-	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
-	disable-wp;
-	st,neg-edge;
-	bus-width = <4>;
-	vmmc-supply = <&v3v3>;
-	vqmmc-supply = <&v3v3>;
-	mmc-ddr-3_3v;
-	status = "okay";
-};
-
-&spi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi1_pins_a>;
-	cs-gpios = <&gpioz 3 0>;
-	/* Use PIO for the display */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";	/* Enable once there is display driver */
-	/*
-	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
-	 * also connected to the display board connector.
-	 */
-};
-
-&usart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usart3_pins_a>;
-	status = "okay";
-};
-
-/*
- * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
- *       however the STM32MP1 pinmux cannot map them to UART4 .
- */
-
-&uart8 {	/* RS485 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart8_pins_a>;
-	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi new file +165 -0

165 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi +4 -0
index 12f89b33987..2324926f9df 100644
@@ -4,3 +4,7 @@
  */
 
 #include "stm32mp15xx-dhcom-u-boot.dtsi"
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts +5 -9
index 52a77c41231..e2e01e2146c 100644
@@ -2,18 +2,14 @@
 /*
  * Copyright (C) 2019 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
 
 / {
 	model = "STMicroelectronics STM32MP15xx DHCOM Premium Developer Kit (2)";
 	compatible = "dh,stm32mp15xx-dhcom-pdk2", "st,stm32mp15x";
-
-	aliases {
-		serial0 = &uart4;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
 };
arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi new file +325 -0

325 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi +5 -1
index 3cac663d987..5bc6698f87f 100644
@@ -11,4 +11,8 @@
 	};
 };
 
-/delete-node/ &ksz8851;
+/delete-node/ &ks8851;
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts +5 -83

97 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi new file +147 -0

147 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcom-som.dtsi renamed from arch/arm/dts/stm32mp15xx-dhcom.dtsi +228 -159

541 lines not on this page · raw message

arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +28 -15

75 lines not on this page · raw message

Signature · 1 line
2.34.1
Reviewed-by on v1 2/2
#2 lore raw

Re: [PATCH 2/2] ARM: dts: stm32: Synchronize DHCOM DTs with Linux 5.15.12

Hi Marek,

Quoted 19 lines · Marek Vasut

Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias and PHY reset GPIO are now reinstated in SoM u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
  arch/arm/dts/stm32mp15xx-dhcom-drc02.dts      | 162 +-------
  arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi     | 165 ++++++++
  .../dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi    |   4 +
  arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts       |  14 +-
  arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi      | 325 +++++++++++++++
  .../dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi |   6 +-
  arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts    |  88 +---
  arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi   | 147 +++++++
  ...-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} | 387 +++++++++++-------
  arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi    |  43 +-
  10 files changed, 917 insertions(+), 424 deletions(-)
Quoted 5 lines

create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi
create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi
create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi rename arch/arm/dts/{stm32mp15xx-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} (56%)

Thanks
Patrick

#3 lore raw

Re: [PATCH 2/2] ARM: dts: stm32: Synchronize DHCOM DTs with Linux 5.15.12

In reply to Marek Vasut

Hi Marek

Quoted 1,649 lines · Marek Vasut

Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias and PHY reset GPIO are now reinstated in SoM u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
 arch/arm/dts/stm32mp15xx-dhcom-drc02.dts      | 162 +-------
 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi     | 165 ++++++++
 .../dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi    |   4 +
 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts       |  14 +-
 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi      | 325 +++++++++++++++
 .../dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi |   6 +-
 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts    |  88 +---
 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi   | 147 +++++++
 ...-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} | 387 +++++++++++-------
 arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi    |  43 +-
 10 files changed, 917 insertions(+), 424 deletions(-)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi
 rename arch/arm/dts/{stm32mp15xx-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} (56%)
arch/arm/dts/stm32mp15xx-dhcom-drc02.dts +5 -157
index 4948ccd4014..1ef9ac29cea 100644
@@ -2,166 +2,14 @@
 /*
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
 
 / {
 	model = "DH Electronics STM32MP15xx DHCOM DRC02";
 	compatible = "dh,stm32mp15xx-dhcom-drc02", "st,stm32mp1xx";
-
-	aliases {
-		serial0 = &uart4;
-		serial1 = &usart3;
-		serial2 = &uart8;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&adc {
-	status = "disabled";
-};
-
-&dac {
-	status = "disabled";
-};
-
-&gpiob {
-	/*
-	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
-	 * GPIO line, however the STM32 UART driver assumes RX happens
-	 * during TX anyway and that it only controls drive enable DE
-	 * line. Hence, the RX is always enabled here.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <8 0>;
-		output-high;
-		line-name = "rs485-rx-en";
-	};
-};
-
-&gpiod {
-	gpio-line-names = "", "", "", "",
-			  "", "", "", "",
-			  "", "", "", "Out1",
-			  "Out2", "", "", "";
-};
-
-&gpioi {
-	gpio-line-names = "In1", "", "", "",
-			  "", "", "", "",
-			  "In2", "", "", "",
-			  "", "", "", "";
-
-	/*
-	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
-	 * pulled high in order to be detected by the USB Controller.
-	 * This signal should be handled by USB power sequencing in
-	 * order to reset the Hub when USB bus is powered down, but
-	 * so far there is no such functionality.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <2 0>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c04";
-		reg = <0x50>;
-		pagesize = <16>;
-	};
-};
-
-&i2c5 {	/* TP7/TP8 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&sdmmc3 {
-	/*
-	 * On DRC02, the SoM does not have SDIO WiFi. The pins
-	 * are used for on-board microSD slot instead.
-	 */
-	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc3_b4_pins_a>;
-	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
-	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
-	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
-	disable-wp;
-	st,neg-edge;
-	bus-width = <4>;
-	vmmc-supply = <&v3v3>;
-	vqmmc-supply = <&v3v3>;
-	mmc-ddr-3_3v;
-	status = "okay";
-};
-
-&spi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi1_pins_a>;
-	cs-gpios = <&gpioz 3 0>;
-	/* Use PIO for the display */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";	/* Enable once there is display driver */
-	/*
-	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
-	 * also connected to the display board connector.
-	 */
-};
-
-&usart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usart3_pins_a>;
-	status = "okay";
-};
-
-/*
- * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
- *       however the STM32MP1 pinmux cannot map them to UART4 .
- */
-
-&uart8 {	/* RS485 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart8_pins_a>;
-	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi new file +165 -0
new file mode 100644
index 00000000000..4b10b013ffd
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&gpiob {
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the STM32 UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <8 0>;
+		output-low;
+		line-name = "rs485-rx-en";
+	};
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DRC02-Out1",
+			  "DRC02-Out2", "", "", "";
+};
+
+&gpioi {
+	gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "DRC02-In2", "", "", "",
+			  "", "", "", "";
+
+	/*
+	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
+	 * pulled high in order to be detected by the USB Controller.
+	 * This signal should be handled by USB power sequencing in
+	 * order to reset the Hub when USB bus is powered down, but
+	 * so far there is no such functionality.
+	 */
+	usb-hub-hog {
+		gpio-hog;
+		gpios = <2 0>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c4 {
+	touchscreen@49 {
+		status = "disabled";
+	};
+};
+
+&i2c5 {	/* TP7/TP8 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc3 {
+	/*
+	 * On DRC02, the SoM does not have SDIO WiFi. The pins
+	 * are used for on-board microSD slot instead.
+	 */
+	/delete-property/broken-cd;
+	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	/* Use PIO for the display */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";	/* Enable once there is display driver */
+	/*
+	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
+	 * also connected to the display board connector.
+	 */
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+/*
+ * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
+ *       however the STM32MP1 pinmux cannot map them to UART4 .
+ */
+
+&uart8 {	/* RS485 */
+	linux,rs485-enabled-at-boot-time;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi +4 -0
index 12f89b33987..2324926f9df 100644
@@ -4,3 +4,7 @@
  */
 
 #include "stm32mp15xx-dhcom-u-boot.dtsi"
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts +5 -9
index 52a77c41231..e2e01e2146c 100644
@@ -2,18 +2,14 @@
 /*
  * Copyright (C) 2019 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
 
 / {
 	model = "STMicroelectronics STM32MP15xx DHCOM Premium Developer Kit (2)";
 	compatible = "dh,stm32mp15xx-dhcom-pdk2", "st,stm32mp15x";
-
-	aliases {
-		serial0 = &uart4;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
 };
arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi new file +325 -0
new file mode 100644
index 00000000000..fbf3826933e
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 3 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_panel_bl>;
+		status = "okay";
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		/*
+		 * The EXTi IRQ line 3 is shared with ethernet,
+		 * so mark this as polled GPIO key.
+		 */
+		button-0 {
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 6 is shared with touchscreen,
+		 * so mark this as polled GPIO key.
+		 */
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 0 is shared with PMIC,
+		 * so mark this as polled GPIO key.
+		 */
+		button-2 {
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-3 {
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "green:led5";
+			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "disabled";
+		};
+
+		led-1 {
+			label = "green:led6";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "green:led7";
+			gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "green:led8";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+		power-supply = <&reg_panel_bl>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_panel_bl: regulator-panel-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_backlight";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_panel_supply>;
+	};
+
+	reg_panel_supply: regulator-panel-supply {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_supply";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		routing =
+			"MIC_IN", "Capture",
+			"Capture", "Mic Bias",
+			"Playback", "HP_OUT";
+		dais = <&sai2a_port &sai2b_port>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {	/* Header X22 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&i2c5 {	/* Header X21 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&v3v3>;
+		VDDIO-supply = <&vdd>;
+
+		sgtl5000_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sgtl5000_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&sgtl5000_tx_endpoint>;
+				bitclock-master = <&sgtl5000_tx_endpoint>;
+			};
+
+			sgtl5000_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&sgtl5000_rx_endpoint>;
+				bitclock-master = <&sgtl5000_rx_endpoint>;
+			};
+		};
+
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-1 = <&ltdc_sleep_pins_b>;
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_tx_endpoint>;
+				format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_rx_endpoint>;
+				format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+	pwm2: pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi +5 -1
index 3cac663d987..5bc6698f87f 100644
@@ -11,4 +11,8 @@
 	};
 };
 
-/delete-node/ &ksz8851;
+/delete-node/ &ks8851;
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts +5 -83
index 59d13713d88..06770b47873 100644
@@ -2,92 +2,14 @@
 /*
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-picoitx.dtsi"
 
 / {
 	model = "DH Electronics STM32MP15xx DHCOM PicoITX";
 	compatible = "dh,stm32mp15xx-dhcom-picoitx", "st,stm32mp1xx";
-
-	aliases {
-		serial0 = &uart4;
-		serial1 = &usart3;
-		serial2 = &uart8;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&adc {
-	status = "disabled";
-};
-
-&dac {
-	status = "disabled";
-};
-
-&gpioa {
-	/*
-	 * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
-	 * port power. This signal should be handled by USB power sequencing
-	 * in order to turn on port power when USB bus is powered up, but so
-	 * far there is no such functionality.
-	 */
-	usb-port-power {
-		gpio-hog;
-		gpios = <13 0>;
-		output-low;
-		line-name = "usb-port-power";
-	};
-};
-
-&i2c2 {	/* On board-to-board connector (optional) */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c5 {	/* On board-to-board connector */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&usart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usart3_pins_a>;
-	status = "okay";
-};
-
-&uart8 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart8_pins_a>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi new file +147 -0
new file mode 100644
index 00000000000..ba816ef8b9b
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "yellow:led";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&fmc {
+	status = "disabled";
+};
+
+&gpioa {
+	/*
+	 * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
+	 * port power. This signal should be handled by USB power sequencing
+	 * in order to turn on port power when USB bus is powered up, but so
+	 * far there is no such functionality.
+	 */
+	usb-port-power-hog {
+		gpio-hog;
+		gpios = <13 0>;
+		output-low;
+		line-name = "usb-port-power";
+	};
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "PicoITX-In1", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "PicoITX-Out1",
+			  "PicoITX-Out2", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "PicoITX-In2", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c2 {	/* On board-to-board connector (optional) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c5 {	/* On board-to-board connector */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ksz8851 {
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcom-som.dtsi renamed from arch/arm/dts/stm32mp15xx-dhcom.dtsi +228 -159
similarity index 56%
rename from arch/arm/dts/stm32mp15xx-dhcom.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcom-som.dtsi
index a1d1b8dec76..8c41f819f77 100644
@@ -1,11 +1,8 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /*
- * Copyright (C) 2019 Marek Vasut <[email protected]>
+ * Copyright (C) 2019-2020 Marek Vasut <[email protected]>
  */
-/dts-v1/;
 
-#include "stm32mp157.dtsi"
-#include "stm32mp15xc.dtsi"
 #include "stm32mp15-pinctrl.dtsi"
 #include "stm32mp15xxaa-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
@@ -13,8 +10,10 @@
 
 / {
 	aliases {
-		eeprom0 = &eeprom0;
 		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
 	};
 
 	memory@c0000000 {
@@ -22,6 +21,48 @@
 		reg = <0xC0000000 0x40000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
 	ethernet_vio: vioregulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vio";
@@ -30,20 +71,45 @@
 		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
 		regulator-always-on;
 		regulator-boot-on;
+		vin-supply = <&vdd>;
 	};
 };
 
-&cec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&cec_pins_a>;
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
 	status = "okay";
+
+	adc1: adc@0 {
+		st,min-sample-time-nsecs = <5000>;
+		st,adc-channels = <0>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <1>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
 };
 
-&dcmi {
+&crc1 {
 	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dcmi_pins_a>;
-	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
 };
 
 &dts {
@@ -53,12 +119,12 @@
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rmii";
 	max-speed = <100>;
 	phy-handle = <&phy0>;
-	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+	st,eth-ref-clk-sel;
 
 	mdio0 {
 		#address-cells = <1>;
@@ -67,16 +133,112 @@
 
 		phy0: ethernet-phy@1 {
 			reg = <1>;
+			/* LAN8710Ai */
+			compatible = "ethernet-phy-id0007.c0f0",
+				     "ethernet-phy-ieee802.3-c22";
+			clocks = <&rcc ETHCK_K>;
+			reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			smsc,disable-energy-detect;
+			interrupt-parent = <&gpioi>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
 };
 
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
 	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-K", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-Q", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-E", "",
+			  "", "", "", "",
+			  "", "", "", "";
+	status = "okay";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DHCOM-F",
+			  "DHCOM-D", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-P", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "DHCOM-A",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "DHCOM-C", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DHCOM-N",
+			  "DHCOM-J", "DHCOM-W", "DHCOM-V", "DHCOM-U",
+			  "DHCOM-T", "", "DHCOM-S", "";
+};
+
+&gpioi {
+	gpio-line-names = "DHCOM-G", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
 };
 
 &i2c4 {
@@ -89,6 +251,11 @@
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
@@ -146,6 +313,7 @@
 
 			vdda: ldo1 {
 				regulator-name = "vdda";
+				regulator-always-on;
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO1 0>;
@@ -168,8 +336,6 @@
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -191,24 +357,23 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
-			 bst_out: boost {
+			bst_out: boost {
 				regulator-name = "bst_out";
 				interrupts = <IT_OCP_BOOST 0>;
-			 };
+			};
 
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-			 };
+			};
 
-			 vbus_sw: pwr_sw2 {
+			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
-			 };
+				regulator-active-discharge = <1>;
+			};
 		};
 
 		onkey {
@@ -225,21 +390,20 @@
 		};
 	};
 
-	eeprom0: eeprom@50 {
+	touchscreen@49 {
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&v3v3>;
+		interrupts-extended = <&gpioh 15 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 	};
 };
 
-&i2c5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-};
-
 &ipcc {
 	status = "okay";
 };
@@ -250,8 +414,12 @@
 };
 
 &m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
 	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
 	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
 	status = "okay";
 };
 
@@ -260,42 +428,6 @@
 	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
 
-&pinctrl {
-	ethernet0_rmii_pins_a: rmii-0 {
-		pins1 {
-			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
-				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
-				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
-				 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
-				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
-				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
-			bias-disable;
-			drive-push-pull;
-			slew-rate = <2>;
-		};
-		pins2 {
-			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
-				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
-				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
-			bias-disable;
-		};
-	};
-
-	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
-		pins1 {
-			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
-				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
-				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
-				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
-				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
-				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
-				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
-				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
-				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
-		};
-	};
-};
-
 &qspi {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
@@ -305,7 +437,7 @@
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
@@ -324,14 +456,19 @@
 };
 
 &sdmmc1 {
-	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-names = "default", "opendrain", "sleep", "init";
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>;
 	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
+	st,use-ckin;
+	st,cmd-gpios = <&gpiod 2 0>;
+	st,ck-gpios = <&gpioc 12 0>;
+	st,ckin-gpios = <&gpioe 4 0>;
 	bus-width = <4>;
 	vmmc-supply = <&vdd_sd>;
 	status = "okay";
@@ -352,75 +489,33 @@
 };
 
 &sdmmc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
 	non-removable;
 	no-sd;
 	no-sdio;
-	st,sig-dir;
 	st,neg-edge;
 	bus-width = <8>;
 	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
 	status = "okay";
 };
 
-&spi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi1_pins_a>;
-	status = "disabled";
-};
-
-&timers2 {
-	/* spare dmas for other usage (un-delete to enable pwm capture) */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";
-	pwm {
-		pinctrl-0 = <&pwm2_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@1 {
-		status = "okay";
-	};
-};
-
-&timers6 {
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
 	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	timer@5 {
-		status = "okay";
-	};
-};
-
-&timers8 {
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";
-	pwm {
-		pinctrl-0 = <&pwm8_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@7 {
-		status = "okay";
-	};
-};
-
-&timers12 {
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";
-	pwm {
-		pinctrl-0 = <&pwm12_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@11 {
-		status = "okay";
-	};
 };
 
 &uart4 {
@@ -428,29 +523,3 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	status = "okay";
 };
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	phy-names = "usb";
-	status = "okay";
-};
-
-&usbotg_hs {
-	dr_mode = "peripheral";
-	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
-	vbus-supply = <&vbus_otg>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
-};
arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +24 -15
index 5b2b09bcfb9..f09f4290f62 100644
@@ -9,6 +9,8 @@
 #include "stm32mp15-ddr3-dhsom-2x2Gb-1066-binG.dtsi"
 #include "stm32mp15-ddr3-dhsom-2x4Gb-1066-binG.dtsi"
 
+/delete-node/ &ksz8851;
+
 / {
 	aliases {
 		i2c1 = &i2c2;
@@ -18,7 +20,8 @@
 		mmc1 = &sdmmc2;
 		spi0 = &qspi;
 		usb0 = &usbotg_hs;
-		ethernet1 = &ksz8851;
+		eeprom0 = &eeprom0;
+		ethernet1 = &ks8851;
 	};
 
 	config {
@@ -30,28 +33,34 @@
 		dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>;
 	};
 
-	led {
-		red {
-			label = "error";
-			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-			status = "okay";
-		};
-
-		blue {
-			default-state = "on";
-		};
-	};
-
 	/* This is actually on FMC2, but we do not have bus driver for that */
-	ksz8851: ks8851mll@64000000 {
+	ks8851: ks8851mll@64000000 {
 		compatible = "micrel,ks8851-mll";
 		reg = <0x64000000 0x20000>;
 	};
 };
 
+&ethernet0 {
+	phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+	/delete-property/ st,eth-ref-clk-sel;
+};
+
+&ethernet0_rmii_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+			 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
+			 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+			 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+	};
+};
+
 &i2c4 {
 	u-boot,dm-pre-reloc;
+
+	eeprom0: eeprom@50 {
+	};
 };
 
 &i2c4_pins_a {

arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi line 79

Quoted 10 lines
arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +4 -0
@@ -61,6 +70,10 @@
 	};
 };
 
+&phy0 {
+	/delete-property/ reset-gpios;
+};
+
 &pinctrl {
 	/* These should bound to FMC2 bus driver, but we do not have one */
 	pinctrl-0 = <&fmc_pins_b &mco2_pins_a>;

Applied to u-boot-stm/master

Thanks
Patrice

#4 lore raw

Re: [PATCH 2/2] ARM: dts: stm32: Synchronize DHCOM DTs with Linux 5.15.12

In reply to Marek Vasut

Hi Marek

Quoted 1,649 lines · Marek Vasut

Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias and PHY reset GPIO are now reinstated in SoM u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
 arch/arm/dts/stm32mp15xx-dhcom-drc02.dts      | 162 +-------
 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi     | 165 ++++++++
 .../dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi    |   4 +
 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts       |  14 +-
 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi      | 325 +++++++++++++++
 .../dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi |   6 +-
 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts    |  88 +---
 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi   | 147 +++++++
 ...-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} | 387 +++++++++++-------
 arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi    |  43 +-
 10 files changed, 917 insertions(+), 424 deletions(-)
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi
 rename arch/arm/dts/{stm32mp15xx-dhcom.dtsi => stm32mp15xx-dhcom-som.dtsi} (56%)
arch/arm/dts/stm32mp15xx-dhcom-drc02.dts +5 -157
index 4948ccd4014..1ef9ac29cea 100644
@@ -2,166 +2,14 @@
 /*
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
 
 / {
 	model = "DH Electronics STM32MP15xx DHCOM DRC02";
 	compatible = "dh,stm32mp15xx-dhcom-drc02", "st,stm32mp1xx";
-
-	aliases {
-		serial0 = &uart4;
-		serial1 = &usart3;
-		serial2 = &uart8;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&adc {
-	status = "disabled";
-};
-
-&dac {
-	status = "disabled";
-};
-
-&gpiob {
-	/*
-	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
-	 * GPIO line, however the STM32 UART driver assumes RX happens
-	 * during TX anyway and that it only controls drive enable DE
-	 * line. Hence, the RX is always enabled here.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <8 0>;
-		output-high;
-		line-name = "rs485-rx-en";
-	};
-};
-
-&gpiod {
-	gpio-line-names = "", "", "", "",
-			  "", "", "", "",
-			  "", "", "", "Out1",
-			  "Out2", "", "", "";
-};
-
-&gpioi {
-	gpio-line-names = "In1", "", "", "",
-			  "", "", "", "",
-			  "In2", "", "", "",
-			  "", "", "", "";
-
-	/*
-	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
-	 * pulled high in order to be detected by the USB Controller.
-	 * This signal should be handled by USB power sequencing in
-	 * order to reset the Hub when USB bus is powered down, but
-	 * so far there is no such functionality.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <2 0>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c04";
-		reg = <0x50>;
-		pagesize = <16>;
-	};
-};
-
-&i2c5 {	/* TP7/TP8 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&sdmmc3 {
-	/*
-	 * On DRC02, the SoM does not have SDIO WiFi. The pins
-	 * are used for on-board microSD slot instead.
-	 */
-	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc3_b4_pins_a>;
-	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
-	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
-	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
-	disable-wp;
-	st,neg-edge;
-	bus-width = <4>;
-	vmmc-supply = <&v3v3>;
-	vqmmc-supply = <&v3v3>;
-	mmc-ddr-3_3v;
-	status = "okay";
-};
-
-&spi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi1_pins_a>;
-	cs-gpios = <&gpioz 3 0>;
-	/* Use PIO for the display */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";	/* Enable once there is display driver */
-	/*
-	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
-	 * also connected to the display board connector.
-	 */
-};
-
-&usart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usart3_pins_a>;
-	status = "okay";
-};
-
-/*
- * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
- *       however the STM32MP1 pinmux cannot map them to UART4 .
- */
-
-&uart8 {	/* RS485 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart8_pins_a>;
-	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
arch/arm/dts/stm32mp15xx-dhcom-drc02.dtsi new file +165 -0
new file mode 100644
index 00000000000..4b10b013ffd
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&gpiob {
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the STM32 UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <8 0>;
+		output-low;
+		line-name = "rs485-rx-en";
+	};
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DRC02-Out1",
+			  "DRC02-Out2", "", "", "";
+};
+
+&gpioi {
+	gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "DRC02-In2", "", "", "",
+			  "", "", "", "";
+
+	/*
+	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
+	 * pulled high in order to be detected by the USB Controller.
+	 * This signal should be handled by USB power sequencing in
+	 * order to reset the Hub when USB bus is powered down, but
+	 * so far there is no such functionality.
+	 */
+	usb-hub-hog {
+		gpio-hog;
+		gpios = <2 0>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c4 {
+	touchscreen@49 {
+		status = "disabled";
+	};
+};
+
+&i2c5 {	/* TP7/TP8 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc3 {
+	/*
+	 * On DRC02, the SoM does not have SDIO WiFi. The pins
+	 * are used for on-board microSD slot instead.
+	 */
+	/delete-property/broken-cd;
+	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	/* Use PIO for the display */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";	/* Enable once there is display driver */
+	/*
+	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
+	 * also connected to the display board connector.
+	 */
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+/*
+ * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
+ *       however the STM32MP1 pinmux cannot map them to UART4 .
+ */
+
+&uart8 {	/* RS485 */
+	linux,rs485-enabled-at-boot-time;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcom-pdk2-u-boot.dtsi +4 -0
index 12f89b33987..2324926f9df 100644
@@ -4,3 +4,7 @@
  */
 
 #include "stm32mp15xx-dhcom-u-boot.dtsi"
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
arch/arm/dts/stm32mp15xx-dhcom-pdk2.dts +5 -9
index 52a77c41231..e2e01e2146c 100644
@@ -2,18 +2,14 @@
 /*
  * Copyright (C) 2019 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
 
 / {
 	model = "STMicroelectronics STM32MP15xx DHCOM Premium Developer Kit (2)";
 	compatible = "dh,stm32mp15xx-dhcom-pdk2", "st,stm32mp15x";
-
-	aliases {
-		serial0 = &uart4;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
 };
arch/arm/dts/stm32mp15xx-dhcom-pdk2.dtsi new file +325 -0
new file mode 100644
index 00000000000..fbf3826933e
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 3 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_panel_bl>;
+		status = "okay";
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		/*
+		 * The EXTi IRQ line 3 is shared with ethernet,
+		 * so mark this as polled GPIO key.
+		 */
+		button-0 {
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 6 is shared with touchscreen,
+		 * so mark this as polled GPIO key.
+		 */
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 0 is shared with PMIC,
+		 * so mark this as polled GPIO key.
+		 */
+		button-2 {
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-3 {
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "green:led5";
+			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "disabled";
+		};
+
+		led-1 {
+			label = "green:led6";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "green:led7";
+			gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "green:led8";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+		power-supply = <&reg_panel_bl>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_panel_bl: regulator-panel-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_backlight";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_panel_supply>;
+	};
+
+	reg_panel_supply: regulator-panel-supply {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_supply";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		routing =
+			"MIC_IN", "Capture",
+			"Capture", "Mic Bias",
+			"Playback", "HP_OUT";
+		dais = <&sai2a_port &sai2b_port>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {	/* Header X22 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&i2c5 {	/* Header X21 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&v3v3>;
+		VDDIO-supply = <&vdd>;
+
+		sgtl5000_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sgtl5000_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&sgtl5000_tx_endpoint>;
+				bitclock-master = <&sgtl5000_tx_endpoint>;
+			};
+
+			sgtl5000_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&sgtl5000_rx_endpoint>;
+				bitclock-master = <&sgtl5000_rx_endpoint>;
+			};
+		};
+
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-1 = <&ltdc_sleep_pins_b>;
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_tx_endpoint>;
+				format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_rx_endpoint>;
+				format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+	pwm2: pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcom-picoitx-u-boot.dtsi +5 -1
index 3cac663d987..5bc6698f87f 100644
@@ -11,4 +11,8 @@
 	};
 };
 
-/delete-node/ &ksz8851;
+/delete-node/ &ks8851;
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+};
arch/arm/dts/stm32mp15xx-dhcom-picoitx.dts +5 -83
index 59d13713d88..06770b47873 100644
@@ -2,92 +2,14 @@
 /*
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
+/dts-v1/;
 
-#include "stm32mp15xx-dhcom.dtsi"
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-picoitx.dtsi"
 
 / {
 	model = "DH Electronics STM32MP15xx DHCOM PicoITX";
 	compatible = "dh,stm32mp15xx-dhcom-picoitx", "st,stm32mp1xx";
-
-	aliases {
-		serial0 = &uart4;
-		serial1 = &usart3;
-		serial2 = &uart8;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&adc {
-	status = "disabled";
-};
-
-&dac {
-	status = "disabled";
-};
-
-&gpioa {
-	/*
-	 * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
-	 * port power. This signal should be handled by USB power sequencing
-	 * in order to turn on port power when USB bus is powered up, but so
-	 * far there is no such functionality.
-	 */
-	usb-port-power {
-		gpio-hog;
-		gpios = <13 0>;
-		output-low;
-		line-name = "usb-port-power";
-	};
-};
-
-&i2c2 {	/* On board-to-board connector (optional) */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c5 {	/* On board-to-board connector */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&usart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usart3_pins_a>;
-	status = "okay";
-};
-
-&uart8 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart8_pins_a>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-	vdda1v1-supply = <&reg11>;
-	vdda1v8-supply = <&reg18>;
 };
arch/arm/dts/stm32mp15xx-dhcom-picoitx.dtsi new file +147 -0
new file mode 100644
index 00000000000..ba816ef8b9b
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "yellow:led";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&fmc {
+	status = "disabled";
+};
+
+&gpioa {
+	/*
+	 * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
+	 * port power. This signal should be handled by USB power sequencing
+	 * in order to turn on port power when USB bus is powered up, but so
+	 * far there is no such functionality.
+	 */
+	usb-port-power-hog {
+		gpio-hog;
+		gpios = <13 0>;
+		output-low;
+		line-name = "usb-port-power";
+	};
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "PicoITX-In1", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "PicoITX-Out1",
+			  "PicoITX-Out2", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "PicoITX-In2", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c2 {	/* On board-to-board connector (optional) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c5 {	/* On board-to-board connector */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ksz8851 {
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcom-som.dtsi renamed from arch/arm/dts/stm32mp15xx-dhcom.dtsi +228 -159
similarity index 56%
rename from arch/arm/dts/stm32mp15xx-dhcom.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcom-som.dtsi
index a1d1b8dec76..8c41f819f77 100644
@@ -1,11 +1,8 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /*
- * Copyright (C) 2019 Marek Vasut <[email protected]>
+ * Copyright (C) 2019-2020 Marek Vasut <[email protected]>
  */
-/dts-v1/;
 
-#include "stm32mp157.dtsi"
-#include "stm32mp15xc.dtsi"
 #include "stm32mp15-pinctrl.dtsi"
 #include "stm32mp15xxaa-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
@@ -13,8 +10,10 @@
 
 / {
 	aliases {
-		eeprom0 = &eeprom0;
 		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
 	};
 
 	memory@c0000000 {
@@ -22,6 +21,48 @@
 		reg = <0xC0000000 0x40000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
 	ethernet_vio: vioregulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vio";
@@ -30,20 +71,45 @@
 		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
 		regulator-always-on;
 		regulator-boot-on;
+		vin-supply = <&vdd>;
 	};
 };
 
-&cec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&cec_pins_a>;
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
 	status = "okay";
+
+	adc1: adc@0 {
+		st,min-sample-time-nsecs = <5000>;
+		st,adc-channels = <0>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <1>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
 };
 
-&dcmi {
+&crc1 {
 	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&dcmi_pins_a>;
-	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
 };
 
 &dts {
@@ -53,12 +119,12 @@
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rmii";
 	max-speed = <100>;
 	phy-handle = <&phy0>;
-	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+	st,eth-ref-clk-sel;
 
 	mdio0 {
 		#address-cells = <1>;
@@ -67,16 +133,112 @@
 
 		phy0: ethernet-phy@1 {
 			reg = <1>;
+			/* LAN8710Ai */
+			compatible = "ethernet-phy-id0007.c0f0",
+				     "ethernet-phy-ieee802.3-c22";
+			clocks = <&rcc ETHCK_K>;
+			reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			smsc,disable-energy-detect;
+			interrupt-parent = <&gpioi>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
 };
 
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
 	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-K", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-Q", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-E", "",
+			  "", "", "", "",
+			  "", "", "", "";
+	status = "okay";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DHCOM-F",
+			  "DHCOM-D", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-P", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "DHCOM-A",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "DHCOM-C", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DHCOM-N",
+			  "DHCOM-J", "DHCOM-W", "DHCOM-V", "DHCOM-U",
+			  "DHCOM-T", "", "DHCOM-S", "";
+};
+
+&gpioi {
+	gpio-line-names = "DHCOM-G", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
 };
 
 &i2c4 {
@@ -89,6 +251,11 @@
 	/delete-property/dmas;
 	/delete-property/dma-names;
 
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
@@ -146,6 +313,7 @@
 
 			vdda: ldo1 {
 				regulator-name = "vdda";
+				regulator-always-on;
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO1 0>;
@@ -168,8 +336,6 @@
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -191,24 +357,23 @@
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
-			 bst_out: boost {
+			bst_out: boost {
 				regulator-name = "bst_out";
 				interrupts = <IT_OCP_BOOST 0>;
-			 };
+			};
 
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-			 };
+			};
 
-			 vbus_sw: pwr_sw2 {
+			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
-			 };
+				regulator-active-discharge = <1>;
+			};
 		};
 
 		onkey {
@@ -225,21 +390,20 @@
 		};
 	};
 
-	eeprom0: eeprom@50 {
+	touchscreen@49 {
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&v3v3>;
+		interrupts-extended = <&gpioh 15 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 	};
 };
 
-&i2c5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c5_pins_a>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-};
-
 &ipcc {
 	status = "okay";
 };
@@ -250,8 +414,12 @@
 };
 
 &m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
 	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
 	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
 	status = "okay";
 };
 
@@ -260,42 +428,6 @@
 	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
 
-&pinctrl {
-	ethernet0_rmii_pins_a: rmii-0 {
-		pins1 {
-			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
-				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
-				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
-				 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
-				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
-				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
-			bias-disable;
-			drive-push-pull;
-			slew-rate = <2>;
-		};
-		pins2 {
-			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
-				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
-				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
-			bias-disable;
-		};
-	};
-
-	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
-		pins1 {
-			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
-				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
-				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
-				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
-				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
-				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
-				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
-				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
-				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
-		};
-	};
-};
-
 &qspi {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
@@ -305,7 +437,7 @@
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
@@ -324,14 +456,19 @@
 };
 
 &sdmmc1 {
-	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-names = "default", "opendrain", "sleep", "init";
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>;
 	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	disable-wp;
 	st,sig-dir;
 	st,neg-edge;
+	st,use-ckin;
+	st,cmd-gpios = <&gpiod 2 0>;
+	st,ck-gpios = <&gpioc 12 0>;
+	st,ckin-gpios = <&gpioe 4 0>;
 	bus-width = <4>;
 	vmmc-supply = <&vdd_sd>;
 	status = "okay";
@@ -352,75 +489,33 @@
 };
 
 &sdmmc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "opendrain", "sleep";
 	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
 	non-removable;
 	no-sd;
 	no-sdio;
-	st,sig-dir;
 	st,neg-edge;
 	bus-width = <8>;
 	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
 	status = "okay";
 };
 
-&spi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi1_pins_a>;
-	status = "disabled";
-};
-
-&timers2 {
-	/* spare dmas for other usage (un-delete to enable pwm capture) */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";
-	pwm {
-		pinctrl-0 = <&pwm2_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@1 {
-		status = "okay";
-	};
-};
-
-&timers6 {
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
 	status = "okay";
-	/* spare dmas for other usage */
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	timer@5 {
-		status = "okay";
-	};
-};
-
-&timers8 {
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";
-	pwm {
-		pinctrl-0 = <&pwm8_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@7 {
-		status = "okay";
-	};
-};
-
-&timers12 {
-	/delete-property/dmas;
-	/delete-property/dma-names;
-	status = "disabled";
-	pwm {
-		pinctrl-0 = <&pwm12_pins_a>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-	timer@11 {
-		status = "okay";
-	};
 };
 
 &uart4 {
@@ -428,29 +523,3 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	status = "okay";
 };
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	phy-names = "usb";
-	status = "okay";
-};
-
-&usbotg_hs {
-	dr_mode = "peripheral";
-	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
-	vbus-supply = <&vbus_otg>;
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
-};
arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +24 -15
index 5b2b09bcfb9..f09f4290f62 100644
@@ -9,6 +9,8 @@
 #include "stm32mp15-ddr3-dhsom-2x2Gb-1066-binG.dtsi"
 #include "stm32mp15-ddr3-dhsom-2x4Gb-1066-binG.dtsi"
 
+/delete-node/ &ksz8851;
+
 / {
 	aliases {
 		i2c1 = &i2c2;
@@ -18,7 +20,8 @@
 		mmc1 = &sdmmc2;
 		spi0 = &qspi;
 		usb0 = &usbotg_hs;
-		ethernet1 = &ksz8851;
+		eeprom0 = &eeprom0;
+		ethernet1 = &ks8851;
 	};
 
 	config {
@@ -30,28 +33,34 @@
 		dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>;
 	};
 
-	led {
-		red {
-			label = "error";
-			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-			status = "okay";
-		};
-
-		blue {
-			default-state = "on";
-		};
-	};
-
 	/* This is actually on FMC2, but we do not have bus driver for that */
-	ksz8851: ks8851mll@64000000 {
+	ks8851: ks8851mll@64000000 {
 		compatible = "micrel,ks8851-mll";
 		reg = <0x64000000 0x20000>;
 	};
 };
 
+&ethernet0 {
+	phy-reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+	/delete-property/ st,eth-ref-clk-sel;
+};
+
+&ethernet0_rmii_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+			 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
+			 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+			 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+	};
+};
+
 &i2c4 {
 	u-boot,dm-pre-reloc;
+
+	eeprom0: eeprom@50 {
+	};
 };
 
 &i2c4_pins_a {

arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi line 79

Quoted 10 lines
arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi +4 -0
@@ -61,6 +70,10 @@
 	};
 };
 
+&phy0 {
+	/delete-property/ reset-gpios;
+};
+
 &pinctrl {
 	/* These should bound to FMC2 bus driver, but we do not have one */
 	pinctrl-0 = <&fmc_pins_b &mco2_pins_a>;

Applied to u-boot-stm/master

Thanks
Patrice

Reviewed-by on v1 1/2
#5 lore raw
In reply to Marek Vasut

Hi Marek,

Quoted 19 lines · Marek Vasut

Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias is now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96 u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
  arch/arm/dts/Makefile                         |   1 -
  arch/arm/dts/stm32mp157a-avenger96.dts        |   8 -
  arch/arm/dts/stm32mp157a-dhcor-avenger96.dts  |  38 ++
  .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi   |   2 +
  arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts  | 202 +-------
  arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi | 431 ++++++++++++++++++
  arch/arm/dts/stm32mp15xx-dhcor-io1v8.dtsi     |   7 +-
  ...-io3v3.dtsi => stm32mp15xx-dhcor-som.dtsi} |  30 +-
  arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi    |   8 +
  9 files changed, 503 insertions(+), 224 deletions(-)
Quoted 5 lines

delete mode 100644 arch/arm/dts/stm32mp157a-avenger96.dts
create mode 100644 arch/arm/dts/stm32mp157a-dhcor-avenger96.dts
create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi
rename arch/arm/dts/{stm32mp15xx-dhcor-io3v3.dtsi => stm32mp15xx-dhcor-som.dtsi} (91%)

Thanks
Patrick

#6 lore raw
In reply to Marek Vasut

Hi Marek

Quoted 935 lines · Marek Vasut

Synchronize DH DHCOR DTs with Linux commit 25960cafa06e ("Linux 5.15.12"). There is no functional change to the resulting DTs. The eeprom0 alias is now reinstated in SoM u-boot dtsi, the PHY reset GPIO is reinstated in AV96 u-boot dtsi.

Cc Patrice Chotard <[email protected]>
Cc Patrick Delaunay <[email protected]>
---
 arch/arm/dts/Makefile                         |   1 -
 arch/arm/dts/stm32mp157a-avenger96.dts        |   8 -
 arch/arm/dts/stm32mp157a-dhcor-avenger96.dts  |  38 ++
 .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi   |   2 +
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts  | 202 +-------
 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi | 431 ++++++++++++++++++
 arch/arm/dts/stm32mp15xx-dhcor-io1v8.dtsi     |   7 +-
 ...-io3v3.dtsi => stm32mp15xx-dhcor-som.dtsi} |  30 +-
 arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi    |   8 +
 9 files changed, 503 insertions(+), 224 deletions(-)
 delete mode 100644 arch/arm/dts/stm32mp157a-avenger96.dts
 create mode 100644 arch/arm/dts/stm32mp157a-dhcor-avenger96.dts
 create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi
 rename arch/arm/dts/{stm32mp15xx-dhcor-io3v3.dtsi => stm32mp15xx-dhcor-som.dtsi} (91%)
arch/arm/dts/Makefile +0 -1
index b3e2a9c9d77..03064632999 100644
@@ -1098,7 +1098,6 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 
 dtb-$(CONFIG_STM32MP15x) += \
 	stm32mp157a-dk1.dtb \
-	stm32mp157a-avenger96.dtb \
 	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
 	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
 	stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
arch/arm/dts/stm32mp157a-avenger96.dts deleted +0 -8
deleted file mode 100644
index 9c165104fbe..00000000000
@@ -1,8 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
-/*
- * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
- * Author: Manivannan Sadhasivam <[email protected]>
- */
-
-/* This is kept for backward compatibility and will be removed */
-#include "stm32mp15xx-dhcor-avenger96.dts"
arch/arm/dts/stm32mp157a-dhcor-avenger96.dts new file +38 -0
new file mode 100644
index 00000000000..2e3c9fbb4eb
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * Avenger96 PCB number: 588-200 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP157A Avenger96 board";
+	compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som",
+		     "st,stm32mp157";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "disabled";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "disabled";
+};
arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi +2 -0
index c96eba99c5e..6e6543b5e4a 100644
@@ -21,6 +21,8 @@
 
 
 &ethernet0 {
+	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+
 	mdio0 {
 		ethernet-phy@7 {
 			reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts +4 -198
index 0e860e5cf88..76ac5a873c1 100644
@@ -7,206 +7,12 @@
 
 /dts-v1/;
 
-#include "stm32mp15xx-dhcor-io1v8.dtsi"
-#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
+#include "stm32mp151.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
 
 / {
 	model = "Arrow Electronics STM32MP15xx Avenger96 board";
 	compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
-
-	aliases {
-		eeprom0 = &eeprom0;
-		ethernet0 = &ethernet0;
-		mmc0 = &sdmmc1;
-		serial0 = &uart4;
-		serial1 = &uart7;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	led {
-		compatible = "gpio-leds";
-		led1 {
-			label = "green:user0";
-			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led2 {
-			label = "green:user1";
-			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led3 {
-			label = "green:user2";
-			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc1";
-			default-state = "off";
-		};
-
-		led4 {
-			label = "green:user3";
-			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "none";
-			default-state = "off";
-			panic-indicator;
-		};
-
-		led5 {
-			label = "yellow:wifi";
-			gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "phy0tx";
-			default-state = "off";
-		};
-
-		led6 {
-			label = "blue:bt";
-			gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "bluetooth-power";
-			default-state = "off";
-		};
-	};
-
-	sd_switch: regulator-sd_switch {
-		compatible = "regulator-gpio";
-		regulator-name = "sd_switch";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <2900000>;
-		regulator-type = "voltage";
-		regulator-always-on;
-
-		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
-		gpios-states = <0>;
-		states = <1800000 0x1>,
-			 <2900000 0x0>;
-	};
-};
-
-&ethernet0 {
-	status = "okay";
-	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
-	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
-	pinctrl-names = "default", "sleep";
-	phy-mode = "rgmii";
-	max-speed = <1000>;
-	phy-handle = <&phy0>;
-	phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
-
-	mdio0 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-		phy0: ethernet-phy@7 {
-			reg = <7>;
-		};
-	};
-};
-
-&i2c1 {	/* X6 I2C1 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_b>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c2 {	/* X6 I2C2 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins_c>;
-	i2c-scl-rising-time-ns = <185>;
-	i2c-scl-falling-time-ns = <20>;
-	status = "okay";
-	/delete-property/dmas;
-	/delete-property/dma-names;
-};
-
-&i2c4 {
-	eeprom0: eeprom@53 {
-		compatible = "atmel,24c02";
-		reg = <0x53>;
-		pagesize = <16>;
-	};
-};
-
-&sdmmc1 {
-	pinctrl-names = "default", "opendrain", "sleep";
-	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
-	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
-	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
-	disable-wp;
-	st,sig-dir;
-	st,neg-edge;
-	st,use-ckin;
-	bus-width = <4>;
-	vmmc-supply = <&vdd_sd>;
-	vqmmc-supply = <&sd_switch>;
-	status = "okay";
-};
-
-&sdmmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
-	non-removable;
-	no-sd;
-	no-sdio;
-	st,neg-edge;
-	bus-width = <8>;
-	vmmc-supply = <&v3v3>;
-	mmc-ddr-3_3v;
-	status = "okay";
-};
-
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>;
-	status = "okay";
-};
-
-&uart4 {
-	/* On Low speed expansion header */
-	label = "LS-UART1";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart4_pins_b>;
-	status = "okay";
-};
-
-&uart7 {
-	/* On Low speed expansion header */
-	label = "LS-UART0";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart7_pins_a>;
-	status = "okay";
-};
-
-&usbh_ehci {
-	phys = <&usbphyc_port0>;
-	phy-names = "usb";
-	status = "okay";
-};
-
-&usbotg_hs {
-	pinctrl-0 = <&usbotg_hs_pins_a>;
-	pinctrl-names = "default";
-	phys = <&usbphyc_port1 0>;
-	phy-names = "usb2-phy";
-	status = "okay";
-};
-
-&usbphyc {
-	status = "okay";
-};
-
-&usbphyc_port0 {
-	phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
-	phy-supply = <&vdd_usb>;
 };
arch/arm/dts/stm32mp15xx-dhcor-avenger96.dtsi new file +431 -0
new file mode 100644
index 00000000000..6885948f302
@@ -0,0 +1,431 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
+ * Copyright (C) 2020 Marek Vasut <[email protected]>
+ */
+
+/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
+#include "stm32mp15xx-dhcor-io1v8.dtsi"
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		serial0 = &uart4;
+		serial1 = &uart7;
+		serial2 = &usart2;
+		spi0 = &qspi;
+	};
+
+	/* XTal Q1 */
+	cec_clock: clk-cec-fixed {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7513_out>;
+			};
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "green:user0";
+			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:user1";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "green:user2";
+			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "green:user3";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP1-AV96-HDMI";
+		dais = <&sai2a_port>;
+		status = "okay";
+	};
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,adc-channels = <0 1 6>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <0 1 2>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "AV96-K",
+			  "AV96-I", "", "AV96-A", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "AV96-J", "", "",
+			  "", "", "", "AV96-B",
+			  "", "AV96-L", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "AV96-C",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "AV96-D", "", "", "",
+			  "", "", "AV96-E", "AV96-F";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "AV96-G", "AV96-H", "", "";
+};
+
+&i2c1 {	/* X6 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c2 {	/* X6 I2C2 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_c>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	hdmi-transmitter@3d {
+		compatible = "adi,adv7513";
+		reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
+		reg-names = "main", "edid", "cec", "packet";
+		clocks = <&cec_clock>;
+		clock-names = "cec";
+
+		avdd-supply = <&v3v3>;
+		dvdd-supply = <&v3v3>;
+		pvdd-supply = <&v3v3>;
+		dvdd-3v-supply = <&v3v3>;
+		bgvdd-supply = <&v3v3>;
+
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+
+		status = "okay";
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7513_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7513_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				adv7513_i2s0: endpoint {
+					remote-endpoint = <&sai2a_endpoint>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_d>;
+	pinctrl-1 = <&ltdc_sleep_pins_d>;
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ltdc_ep0_out: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&adv7513_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_c>;
+	pinctrl-1 = <&sai2a_sleep_pins_c>;
+	clock-names = "pclk", "x8k", "x11k";
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&adv7513_i2s0>;
+				format = "i2s";
+				mclk-fs = <256>;
+			};
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd_io>;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	/* On Low speed expansion header */
+	label = "LS-UART1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	status = "okay";
+};
+
+&uart7 {
+	/* On Low speed expansion header */
+	label = "LS-UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* Bluetooth */
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	st,hw-flow-ctrl;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	status = "okay";
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
arch/arm/dts/stm32mp15xx-dhcor-io1v8.dtsi +3 -4
index 75435424d67..75172314d7a 100644
@@ -1,12 +1,12 @@
 // SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
 /*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <[email protected]>
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
 
-#include "stm32mp15xx-dhcor-io3v3.dtsi"
-
 / {
-	/* Enpirion EP3A8LQI U2 on the 1V8 IO DHCOR */
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
 	vdd_io: regulator-buck-io {
 		compatible = "regulator-fixed";
 		regulator-name = "buck-io";
@@ -20,5 +20,4 @@
 
 &pwr_regulators {
 	vdd-supply = <&vdd_io>;
-	vdd_3v3_usbfs-supply = <&vdd_usb>;
 };
arch/arm/dts/stm32mp15xx-dhcor-som.dtsi renamed from arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi +17 -13
similarity index 91%
rename from arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi
rename to arch/arm/dts/stm32mp15xx-dhcor-som.dtsi
index 94cf80dbede..44ecc470858 100644
@@ -4,9 +4,7 @@
  * Author: Manivannan Sadhasivam <[email protected]>
  * Copyright (C) 2020 Marek Vasut <[email protected]>
  */
-/dts-v1/;
 
-#include "stm32mp157.dtsi"
 #include "stm32mp15-pinctrl.dtsi"
 #include "stm32mp15xxac-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
@@ -23,6 +21,14 @@
 	};
 };
 
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
 &i2c4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c4_pins_a>;
@@ -35,7 +41,7 @@
 	pmic: stpmic@33 {
 		compatible = "st,stpmic1";
 		reg = <0x33>;
-		interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		status = "okay";
@@ -53,7 +59,7 @@
 
 			vddcore: buck1 {
 				regulator-name = "vddcore";
-				regulator-min-microvolt = <800000>;
+				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1350000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
@@ -92,7 +98,6 @@
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO1 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			v2v8: ldo2 {
@@ -100,7 +105,6 @@
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
 				interrupts = <IT_CURLIM_LDO2 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vtt_ddr: ldo3 {
@@ -114,7 +118,6 @@
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
 				interrupts = <IT_CURLIM_LDO4 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vdd_sd: ldo5 {
@@ -122,7 +125,6 @@
 				regulator-min-microvolt = <2900000>;
 				regulator-max-microvolt = <2900000>;
 				interrupts = <IT_CURLIM_LDO5 0>;
-				interrupt-parent = <&pmic>;
 				regulator-boot-on;
 			};
 
@@ -131,7 +133,6 @@
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				interrupts = <IT_CURLIM_LDO6 0>;
-				interrupt-parent = <&pmic>;
 				regulator-enable-ramp-delay = <300000>;
 			};
 
@@ -143,20 +144,17 @@
 			bst_out: boost {
 				regulator-name = "bst_out";
 				interrupts = <IT_OCP_BOOST 0>;
-				interrupt-parent = <&pmic>;
 			};
 
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				interrupt-parent = <&pmic>;
 				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				interrupt-parent = <&pmic>;
 				regulator-active-discharge = <1>;
 			};
 		};
@@ -173,6 +171,12 @@
 			status = "disabled";
 		};
 	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
 };
 
 &iwdg2 {
@@ -194,7 +198,7 @@
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: spi-flash@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi +5 -0
index 71375510b4a..338b674368a 100644
@@ -15,6 +15,11 @@
 
 / {
 	u-boot,dm-pre-reloc;
+
+	aliases {
+		eeprom0 = &eeprom0;
+	};
+
 	config {
 		dh,ddr3-coding-gpios = <&gpiog 0 0>, <&gpiog 1 0>;
 		dh,som-coding-gpios = <&gpioz 7 0>, <&gpiof 3 0>;

arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi line 41

Quoted 9 lines
arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi +3 -0
@@ -28,6 +33,9 @@
 &i2c4 {
 	u-boot,dm-pre-reloc;
 	u-boot,dm-spl;
+
+	eeprom0: eeprom@53 {
+	};
 };
 
 &i2c4_pins_a {

Applied to u-boot-stm/master

Thanks
Patrice