Skip to contentSkip to conversation

i2c: at91: add compatible with microchip,sama7g5-i2c

PATCH In review Eugen Hristev 2 participants 9 messages Jan 4, 2022 – Jan 17, 2022

Subsystems (3)
lore
Share & tools
lore
#1 lore raw

PATCH 2/4 ARM: dts: at91: sama7g5: add flx8 and required nodes

In reply to Eugen Hristev

Add Flexcom8 node with required referenced nodes as phandles. Since Flexcom8 is present in Linux, take the node exactly as-is from Linux. Some nodes are referenced in Linux as phandles, the dma and the gic. Add them as well to the file, even if they are unused by Uboot. This is a step towards having the U-boot DT equivalent with the DT in Linux.

---
 arch/arm/dts/sama7g5.dtsi | 50 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)
arch/arm/dts/sama7g5.dtsi +50 -0
index 4a3c675d34..2505a2f83d 100644
@@ -10,11 +10,15 @@
  */
 
 #include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clk/at91.h>
+#include <dt-bindings/dma/at91.h>
 
 / {
 	model = "Microchip SAMA7G5 family SoC";
 	compatible = "microchip,sama7g5";
+	interrupt-parent = <&gic>;
 
 	clocks {
 		slow_rc_osc: slow_rc_osc {
@@ -191,6 +195,52 @@
 				clock-names = "pclk", "hclk";
 				status = "disabled";
 			};
+
+			dma0: dma-controller@e2808000 {
+				compatible = "microchip,sama7g5-dma";
+				reg = <0xe2808000 0x1000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				#dma-cells = <1>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+				clock-names = "dma_clk";
+				status = "disabled";
+			};
+
+			flx8: flexcom@e2818000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xe2818000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xe2818000 0x800>;
+				status = "disabled";
+
+				i2c8: i2c@600 {
+					compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
+					atmel,fifo-size = <32>;
+					dmas = <&dma0 AT91_XDMAC_DT_PERID(21)>,
+						<&dma0 AT91_XDMAC_DT_PERID(22)>;
+					dma-names = "rx", "tx";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					status = "disabled";
+				};
+			};
+
+			gic: interrupt-controller@e8c11000 {
+				compatible = "arm,cortex-a7-gic";
+				#interrupt-cells = <3>;
+				#address-cells = <0>;
+				interrupt-controller;
+				interrupt-parent;
+				reg = <0xe8c11000 0x1000>,
+					<0xe8c12000 0x2000>;
+			};
 		};
 	};
 };
Signature · 1 line
2.25.1
#0 lore raw

PATCH 1/4 i2c: at91: add compatible with microchip,sama7g5-i2c

Add compatible and data platform struct for sama7g5 SoC.

---
 drivers/i2c/at91_i2c.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/i2c/at91_i2c.c +6 -0
index 6b4c0e4804..400a3786ca 100644
@@ -305,6 +305,11 @@ static const struct at91_i2c_pdata sama5d2_config = {
 	.clk_offset = 3,
 };
 
+static const struct at91_i2c_pdata sama7g5_config = {
+	.clk_max_div = 7,
+	.clk_offset = 3,
+};
+
 static const struct udevice_id at91_i2c_ids[] = {
 { .compatible = "atmel,at91rm9200-i2c", .data = (long)&at91rm9200_config },
 { .compatible = "atmel,at91sam9260-i2c", .data = (long)&at91sam9260_config },
@@ -314,6 +319,7 @@ static const struct udevice_id at91_i2c_ids[] = {
 { .compatible = "atmel,at91sam9x5-i2c", .data = (long)&at91sam9x5_config },
 { .compatible = "atmel,sama5d4-i2c", .data = (long)&sama5d4_config },
 { .compatible = "atmel,sama5d2-i2c", .data = (long)&sama5d2_config },
+{ .compatible = "microchip,sama7g5-i2c", .data = (long)&sama7g5_config },
 { }
 };
 
Signature · 1 line
2.25.1
#2 lore raw

PATCH 3/4 ARM: dts: at91: sama7g5ek: move eeproms to flexcom8

The rev4 of the board sama7g5ek has the eeproms on flexcom8 instead of flexcom1.
Initialize flexcom8 with required pincontrol and move the eeproms accordingly.

---
 arch/arm/dts/sama7g5ek.dts | 39 +++++++++++++++++++++++++++++---------
 1 file changed, 30 insertions(+), 9 deletions(-)
arch/arm/dts/sama7g5ek.dts +30 -9
index 16192ca0b1..6adb044258 100644
@@ -20,6 +20,7 @@
 	aliases {
 		serial0 = &uart0;
 		i2c0 = &i2c1;
+		i2c1 = &i2c8;
 	};
 
 	chosen {
@@ -92,17 +93,31 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flx1_default>;
 	status = "okay";
+};
 
-	eeprom@52 {
-		compatible = "microchip,24aa02e48";
-		reg = <0x52>;
-		pagesize = <16>;
-	};
+&flx8 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c8: i2c@600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c8_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
 
-	eeprom@53 {
-		compatible = "microchip,24aa02e48";
-		reg = <0x53>;
-		pagesize = <16>;
+		eeprom@52 {
+			compatible = "microchip,24aa02e48";
+			reg = <0x52>;
+			pagesize = <16>;
+		};
+
+		eeprom@53 {
+			compatible = "microchip,24aa02e48";
+			reg = <0x53>;
+			pagesize = <16>;
+		};
 	};
 };
 
@@ -145,6 +160,12 @@
 		bias-pull-up;
 	};
 
+	pinctrl_i2c8_default: i2c8_default {
+		pinmux = <PIN_PC14__FLEXCOM8_IO0>,
+			 <PIN_PC13__FLEXCOM8_IO1>;
+		bias-disable;
+	};
+
 	pinctrl_qspi: qspi {
 		pinmux = <PIN_PB12__QSPI0_IO0>,
 			 <PIN_PB11__QSPI0_IO1>,
Signature · 1 line
2.25.1
#3 lore raw

PATCH 4/4 configs: at91: sama7g5ek: enable CONFIG_PHANDLE_CHECK_SEQ

In reply to Eugen Hristev

CONFIG_PHANDLE_CHECK_SEQ will allow different sequence number for nodes that have the same name, but they are different.
In sama7g5ek case, there are multiple 'i2c@600' nodes which are child nodes of different parent 'flexcom' nodes.
These are different i2c busses even if the node is the same, and have to be differentiated.
Without this config, the sequence number 0 is reused for two i2c busses, and this is something that we have to avoid:

Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
Looking for 'i2c' at 6236, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0

After this patch:

Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
- i2c1, /ahb/apb/flexcom@e2818000/i2c@600
Found seq 1

Before the patch:
=> i2c bus

Bus 0:  i2c@600
Bus 0:  i2c@600  (active 0)

52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
=>

After the patch:
=> i2c bus

Bus 0:  i2c@600
Bus 1:  i2c@600  (active 1)

52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0

---
 configs/sama7g5ek_mmc1_defconfig | 1 +
 configs/sama7g5ek_mmc_defconfig  | 1 +
 2 files changed, 2 insertions(+)
configs/sama7g5ek_mmc1_defconfig +1 -0
index e297489900..15a5c54e75 100644
@@ -72,3 +72,4 @@ CONFIG_TIMER=y
 CONFIG_MCHP_PIT64B_TIMER=y
 CONFIG_OF_LIBFDT_OVERLAY=y
 # CONFIG_EFI_LOADER_HII is not set
+CONFIG_PHANDLE_CHECK_SEQ=y
configs/sama7g5ek_mmc_defconfig +1 -0
index 4f68a46456..7abd5c8a38 100644
@@ -72,3 +72,4 @@ CONFIG_TIMER=y
 CONFIG_MCHP_PIT64B_TIMER=y
 CONFIG_OF_LIBFDT_OVERLAY=y
 # CONFIG_EFI_LOADER_HII is not set
+CONFIG_PHANDLE_CHECK_SEQ=y
Signature · 1 line
2.25.1
#4 lore raw
In reply to Eugen Hristev

Hi,

Quoted 24 lines

Add compatible and data platform struct for sama7g5 SoC.

---
 drivers/i2c/at91_i2c.c | 6 ++++++
 1 file changed, 6 insertions(+)
drivers/i2c/at91_i2c.c +5 -0
index 6b4c0e4804..400a3786ca 100644
@@ -305,6 +305,11 @@ static const struct at91_i2c_pdata sama5d2_config = {
 	.clk_offset = 3,
 };
 
+static const struct at91_i2c_pdata sama7g5_config = {
+	.clk_max_div = 7,
+	.clk_offset = 3,
+};
+
 static const struct udevice_id at91_i2c_ids[] = {
 { .compatible = "atmel,at91rm9200-i2c", .data = (long)&at91rm9200_config },
 { .compatible = "atmel,at91sam9260-i2c", .data = (long)&at91sam9260_config },

drivers/i2c/at91_i2c.c static const struct udevice_id at91_i2c_ids[] = { · line 322

Quoted 4 lines
drivers/i2c/at91_i2c.c +1 -0
@@ -314,6 +319,7 @@ static const struct udevice_id at91_i2c_ids[] = {
 { .compatible = "atmel,at91sam9x5-i2c", .data = (long)&at91sam9x5_config },
 { .compatible = "atmel,sama5d4-i2c", .data = (long)&sama5d4_config },
 { .compatible = "atmel,sama5d2-i2c", .data = (long)&sama5d2_config },
+{ .compatible = "microchip,sama7g5-i2c", .data = (long)&sama7g5_config },

I see that this compatible string is is also used in the linux device tree, but there is no dt binding for it in linux. Could you add it, so the binding is approved by Rob?

-michael

#5 lore raw
Quoted 26 lines · Michael Walle

Hi,

Quoted 24 lines

Add compatible and data platform struct for sama7g5 SoC.

---
  drivers/i2c/at91_i2c.c | 6 ++++++
  1 file changed, 6 insertions(+)
drivers/i2c/at91_i2c.c +5 -0
index 6b4c0e4804..400a3786ca 100644
@@ -305,6 +305,11 @@ static const struct at91_i2c_pdata sama5d2_config = {
       .clk_offset = 3,
  };
 
+static const struct at91_i2c_pdata sama7g5_config = {
+     .clk_max_div = 7,
+     .clk_offset = 3,
+};
+
  static const struct udevice_id at91_i2c_ids[] = {
  { .compatible = "atmel,at91rm9200-i2c", .data = (long)&at91rm9200_config },
  { .compatible = "atmel,at91sam9260-i2c", .data = (long)&at91sam9260_config },
@@ -314,6 +319,7 @@ static const struct udevice_id at91_i2c_ids[] = {
Quoted 8 lines

drivers/i2c/at91_i2c.c static const struct udevice_id at91_i2c_ids[] = { · line 322

Quoted 4 lines
drivers/i2c/at91_i2c.c +1 -0
  { .compatible = "atmel,at91sam9x5-i2c", .data = (long)&at91sam9x5_config },
  { .compatible = "atmel,sama5d4-i2c", .data = (long)&sama5d4_config },
  { .compatible = "atmel,sama5d2-i2c", .data = (long)&sama5d2_config },
+{ .compatible = "microchip,sama7g5-i2c", .data = (long)&sama7g5_config },

I see that this compatible string is is also used in the linux device tree, but there is no dt binding for it in linux. Could you add it, so the binding is approved by Rob?

I can, for sure, but the current binding format is txt. I am not sure if we have to convert to yaml first, in which case it would be a little more difficult than just adding a new compatible string.
The current DT node in Linux is also compatible with sam9x60, and this string is already in the Linux binding file.
I could add the sam9x60 compatible instead, and it will still work, as 9x60 type of i2c is the same as in sama7g5.
You think this option would be better for now ?

Quoted 3 lines

-michael

#6 lore raw

Am 2022-01-05 11:37, schrieb [email protected]:

Quoted 43 lines · Michael Walle
Quoted 33 lines

Hi,

Quoted 31 lines

Add compatible and data platform struct for sama7g5 SoC.

---
  drivers/i2c/at91_i2c.c | 6 ++++++
  1 file changed, 6 insertions(+)
drivers/i2c/at91_i2c.c +5 -0
index 6b4c0e4804..400a3786ca 100644
@@ -305,6 +305,11 @@ static const struct at91_i2c_pdata 
 sama5d2_config = {
       .clk_offset = 3,
  };
 
+static const struct at91_i2c_pdata sama7g5_config = {
+     .clk_max_div = 7,
+     .clk_offset = 3,
+};
+
  static const struct udevice_id at91_i2c_ids[] = {
  { .compatible = "atmel,at91rm9200-i2c", .data = 

(long)&at91rm9200_config },
{ .compatible = "atmel,at91sam9260-i2c", .data =
(long)&at91sam9260_config },

drivers/i2c/at91_i2c.c +0 -0
@@ -314,6 +319,7 @@ static const struct udevice_id at91_i2c_ids[] = {
  { .compatible = "atmel,at91sam9x5-i2c", .data = 
 (long)&at91sam9x5_config },
  { .compatible = "atmel,sama5d4-i2c", .data = (long)&sama5d4_config 
 },
Quoted 8 lines
Quoted 4 lines
drivers/i2c/at91_i2c.c +1 -0
  { .compatible = "atmel,sama5d2-i2c", .data = (long)&sama5d2_config 
 },
+{ .compatible = "microchip,sama7g5-i2c", .data = 

(long)&sama7g5_config },

I see that this compatible string is is also used in the linux device tree, but there is no dt binding for it in linux. Could you add it, so the binding is approved by Rob?

Quoted 8 lines

I can, for sure, but the current binding format is txt. I am not sure if we have to convert to yaml first, in which case it would be a little more difficult than just adding a new compatible string.
The current DT node in Linux is also compatible with sam9x60, and this string is already in the Linux binding file.
I could add the sam9x60 compatible instead, and it will still work, as 9x60 type of i2c is the same as in sama7g5.
You think this option would be better for now ?

It's at least better than adding an undocumented string. But TBH, this looks like "what can I do to avoid converting the dt binding to yaml". Which eventually has to be done anyway, so now might be a good opportunity for that :)

But looking at sama7g5_config above again, will that also be the correct values for the generic sam9x60?

-michael

#7 lore raw
Quoted 54 lines · Michael Walle

Am 2022-01-05 11:37, schrieb [email protected]:

Quoted 43 lines · Michael Walle
Quoted 33 lines

Hi,

Quoted 31 lines

Add compatible and data platform struct for sama7g5 SoC.

---
  drivers/i2c/at91_i2c.c | 6 ++++++

  1 file changed, 6 insertions(+)
drivers/i2c/at91_i2c.c +5 -0
index 6b4c0e4804..400a3786ca 100644
@@ -305,6 +305,11 @@ static const struct at91_i2c_pdata
 sama5d2_config = {
        .clk_offset = 3,
   };
 
+static const struct at91_i2c_pdata sama7g5_config = {
+     .clk_max_div = 7,
+     .clk_offset = 3,
+};
+
   static const struct udevice_id at91_i2c_ids[] = {

  { .compatible = "atmel,at91rm9200-i2c", .data = (long)&at91rm9200_config },
  { .compatible = "atmel,at91sam9260-i2c", .data = (long)&at91sam9260_config },

drivers/i2c/at91_i2c.c +0 -0
@@ -314,6 +319,7 @@ static const struct udevice_id at91_i2c_ids[] = {

  { .compatible = "atmel,at91sam9x5-i2c", .data = (long)&at91sam9x5_config },
  { .compatible = "atmel,sama5d4-i2c", .data = (long)&sama5d4_config },

Quoted 8 lines
Quoted 4 lines

  { .compatible = "atmel,sama5d2-i2c", .data = (long)&sama5d2_config },
+{ .compatible = "microchip,sama7g5-i2c", .data = (long)&sama7g5_config },

I see that this compatible string is is also used in the linux device tree, but there is no dt binding for it in linux. Could you add it, so the binding is approved by Rob?

Quoted 9 lines

I can, for sure, but the current binding format is txt. I am not sure if
we have to convert to yaml first, in which case it would be a little more difficult than just adding a new compatible string. The current DT node in Linux is also compatible with sam9x60, and this string is already in the Linux binding file.
I could add the sam9x60 compatible instead, and it will still work, as 9x60 type of i2c is the same as in sama7g5.
You think this option would be better for now ?

Quoted 4 lines

It's at least better than adding an undocumented string. But TBH, this looks like "what can I do to avoid converting the dt binding to yaml". Which eventually has to be done anyway, so now might be a good opportunity for that :)

You are right. It has to be done anyway, but I would not like to stop the addition to u-boot because of that.
Converting the i2c to yaml might open several other issues, and this might delay a simple compatible string in uboot a lot. sam9x60 compatible has to be added anyway, since it's supported and it's already in the binding tree.
So I see this like an intermediary step.

Quoted 3 lines

But looking at sama7g5_config above again, will that also be the correct values for the generic sam9x60?

That's right.
I will follow up with a patch to add sam9x60, and think of converting the i2c binding later on.

Quoted 2 lines

-michael