Skip to contentSkip to conversation

imx: imx8qm-rom7720: switch to binman

RFC In review Oliver Graute 5 participants 8 messages Jan 10, 2022 – Jan 26, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

RFC 1/1 imx: imx8qm-rom7720: switch to binman

Switch to use binman to pack images

---

Run into this issue on the first try to get binman working:

make[1]: Nothing to be done for 'SPL'.
BINMAN flash.bin
MKIMAGE flash.bin
Error: spl/u-boot-spl.cfgout[16] - Invalid command (LOADER) arch/arm/mach-imx/Makefile:190: recipe for target 'flash.bin' failed make[1]: *** [flash.bin] Error 1
make[1]: *** Deleting file 'flash.bin'
Makefile:1519: recipe for target 'flash.bin' failed
make: *** [flash.bin] Error 2

Some clue howto fix that?

 arch/arm/dts/imx8qm-rom7720-a1.dts            |  1 +
 arch/arm/dts/imx8qm-u-boot.dtsi               | 95 +++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig                |  1 +
 .../advantech/imx8qm_rom7720_a1/imximage.cfg  | 16 +---
 configs/imx8qm_rom7720_a1_4G_defconfig        |  2 +-
 5 files changed, 100 insertions(+), 15 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-u-boot.dtsi
arch/arm/dts/imx8qm-rom7720-a1.dts +1 -0
index d1f2fff869..332d441c6d 100644
@@ -10,6 +10,7 @@
 /memreserve/ 0x80000000 0x00020000;
 
 #include "fsl-imx8qm.dtsi"
+#include "imx8qm-u-boot.dtsi"
 
 / {
 	model = "Advantech iMX8QM Qseven series";
arch/arm/dts/imx8qm-u-boot.dtsi new file +95 -0

95 lines not on this page · raw message

arch/arm/mach-imx/imx8/Kconfig +1 -0
index b43739e5c6..b42b985cdf 100644
@@ -81,6 +81,7 @@ config TARGET_CONGA_QMX8
 
 config TARGET_IMX8QM_ROM7720_A1
 	bool "Support i.MX8QM ROM-7720-A1"
+	select BINMAN
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
 	select IMX8QM
board/advantech/imx8qm_rom7720_a1/imximage.cfg +2 -14
index e324c7ca37..30556ff9d7 100644
@@ -5,17 +5,5 @@
 
 #define __ASSEMBLY__
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000
+BOOT_FROM	sd
+LOADER		u-boot-dtb.bin	0x10000
configs/imx8qm_rom7720_a1_4G_defconfig +1 -1
index fb43fa1962..07ea6e191d 100644
@@ -18,7 +18,7 @@ CONFIG_SPL=y
 CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_SPL_FIT_GENERATOR is not set
 CONFIG_BOOTDELAY=3
 CONFIG_LOG=y
 CONFIG_BOARD_EARLY_INIT_F=y
Signature · 1 line
2.17.1
#1 lore raw

Hello Oliver,

Quoted 11 lines

-----Original Message-----
From: Oliver Graute <[email protected]>
Sent: Monday, January 10, 2022 11:31 AM
To: Oliver Graute <[email protected]>; Stefano Babic <[email protected]>; Fabio Estevam <[email protected]>; NXP i.MX U-Boot Team <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; ZHIZHIKIN Andrey <[email protected]>; [email protected]
Subject: [RFC] imx: imx8qm-rom7720: switch to binman

Quoted 1 line

Switch to use binman to pack images

Please don't forget S-o-B, checkpatch does complain about it. ;)

Quoted 15 lines

---

Run into this issue on the first try to get binman working:

make[1]: Nothing to be done for 'SPL'.
BINMAN flash.bin
MKIMAGE flash.bin
Error: spl/u-boot-spl.cfgout[16] - Invalid command (LOADER) arch/arm/mach-imx/Makefile:190: recipe for target 'flash.bin' failed make[1]: *** [flash.bin] Error 1
make[1]: *** Deleting file 'flash.bin'
Makefile:1519: recipe for target 'flash.bin' failed
make: *** [flash.bin] Error 2

Quoted 1 line

Some clue howto fix that?

This might be due to the fact that you're using the same u-boot-nodtb.bin binary twice: once in binman section, and once in ITB. You can try to rename the binman entry to a different name, this might do the trick. See [1] for sample of imx8mq_evk conversion.

Quoted 6 lines
 arch/arm/dts/imx8qm-rom7720-a1.dts            |  1 +
 arch/arm/dts/imx8qm-u-boot.dtsi               | 95 +++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig                |  1 +
 .../advantech/imx8qm_rom7720_a1/imximage.cfg  | 16 +---
 configs/imx8qm_rom7720_a1_4G_defconfig        |  2 +-

Is there any documentation available for this board that needs adaptions with new build instructions? I was not able to locate any doc for this board at all...

Quoted 34 lines
 5 files changed, 100 insertions(+), 15 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-u-boot.dtsi
arch/arm/dts/imx8qm-rom7720- renamed from arch/arm/dts/imx8qm-rom7720-a1.dts +0 -0

a1.dts
index d1f2fff869..332d441c6d 100644

arch/arm/dts/imx8qm-rom7720-a1.dts +1 -0
@@ -10,6 +10,7 @@
 /memreserve/ 0x80000000 0x00020000;
 
 #include "fsl-imx8qm.dtsi"
+#include "imx8qm-u-boot.dtsi"
 
 / {
        model = "Advantech iMX8QM Qseven series";
arch/arm/dts/imx8qm-u-boot.dtsi new file +12 -0
new file mode 100644
index 0000000000..77e5cd6989
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ */
+
+/ {
+       binman: binman {
+               multiple-images;
+       };
+
+};
+

arch/arm/dts/imx8qm-u-boot.dtsi line 22

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +10 -0
+&binman {
+       u-boot-nodtb {
+               filename = "u-boot-nodtb.bin";
+               pad-byte = <0xff>;
+               align-size = <4>;
+               align = <4>;
+
+               u-boot-spl {
+                       align-end = <4>;
+               };

What I see is missing in this section is SECO and SCFW binaries.

Can i.MX8QM boot without those? Otherwise generated image will be unusable.

Quoted 42 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +6 -0
+
+       };
+
+       flash {
+               mkimage {
+                       args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e

0x100000";

arch/arm/dts/imx8qm-u-boot.dtsi new file +35 -0
+
+                       blob {
+                               filename = "u-boot-nodtb.bin";
+                       };
+
+               };
+
+       };
+
+       itb {
+               filename = "u-boot.itb";
+
+               fit {
+                       description = "Configuration to load ATF before U-Boot";
+                       #address-cells = <1>;
+                       fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+
+                       images {
+                               uboot {
+                                       description = "U-Boot (64-bit)";
+                                       type = "standalone";
+                                       arch = "arm64";
+                                       compression = "none";
+                                       load = <CONFIG_SYS_TEXT_BASE>;
+
+                                       uboot_blob: blob-ext {
+                                               filename = "u-boot-nodtb.bin";
+                                       };
+                               };
+
+                               atf {
+                                       description = "ARM Trusted Firmware";
+                                       type = "firmware";
+                                       arch = "arm64";
+                                       compression = "none";

arch/arm/dts/imx8qm-u-boot.dtsi line 73

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +10 -0
+                                       load = <0x80000000>;
+                                       entry = <0x80000000>;
+
+                                       atf_blob: blob-ext {
+                                               filename = "bl31.bin";
+                                       };
+                               };
+
+                               fdt {
+                                       description = "imx8qm-rom7720-a1";

You can use "NAME" here I suppose.

Quoted 4 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +4 -0
+                                       type = "flat_dt";
+                                       compression = "none";
+
+                                       uboot_fdt_blob: blob-ext {

arch/arm/dts/imx8qm-u-boot.dtsi line 87

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +10 -0
+                                               filename = "u-boot.dtb";
+                                       };
+                               };
+                       };
+
+                       configurations {
+                               default = "conf";
+
+                               conf {
+                                       description = "imx8qm-rom7720-a1";

And as well here, "NAME".

arch/arm/dts/imx8qm-u-boot.dtsi line 95

Quoted 8 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +8 -0
+                                       firmware = "uboot";
+                                       loadables = "atf";
+                                       fdt = "fdt";
+                               };
+                       };
+               };
+       };
+};

This binman configuration suggests that there are 2 binaries that should be populated onto the bootable media: flash.bin and u-boot.itb. Can you please convert them to use a single binary? Sample code for this is also in [1].

Quoted 52 lines
arch/arm/mach-imx/imx8/Kconfig +1 -0
index b43739e5c6..b42b985cdf 100644
@@ -81,6 +81,7 @@ config TARGET_CONGA_QMX8
 
 config TARGET_IMX8QM_ROM7720_A1
        bool "Support i.MX8QM ROM-7720-A1"
+       select BINMAN
        select BOARD_LATE_INIT
        select SUPPORT_SPL
        select IMX8QM
board/advantech/imx8qm_rom7720_a1/imximage.cfg +2 -14
index e324c7ca37..30556ff9d7 100644
@@ -5,17 +5,5 @@
 
 #define __ASSEMBLY__
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000
+BOOT_FROM      sd
+LOADER         u-boot-dtb.bin  0x10000
configs/imx8qm_rom7720_a1_4G_defconfig +1 -2
index fb43fa1962..07ea6e191d 100644
@@ -18,7 +18,7 @@ CONFIG_SPL=y
 CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_SPL_FIT_GENERATOR is not set
 CONFIG_BOOTDELAY=3
 CONFIG_LOG=y
 CONFIG_BOARD_EARLY_INIT_F=y
--
Quoted 1 line

2.17.1

-- andrey

#2 lore raw
Quoted 13 lines · ZHIZHIKIN Andrey

Hello Oliver,

Quoted 11 lines

-----Original Message-----
From: Oliver Graute <[email protected]>
Sent: Monday, January 10, 2022 11:31 AM
To: Oliver Graute <[email protected]>; Stefano Babic <[email protected]>; Fabio Estevam <[email protected]>; NXP i.MX U-Boot Team <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; ZHIZHIKIN Andrey <[email protected]>; [email protected]
Subject: [RFC] imx: imx8qm-rom7720: switch to binman

Quoted 3 lines
Quoted 1 line

Switch to use binman to pack images

Please don't forget S-o-B, checkpatch does complain about it. ;)

will do it on next submission

Quoted 15 lines
Quoted 15 lines

---

Run into this issue on the first try to get binman working:

make[1]: Nothing to be done for 'SPL'.
BINMAN flash.bin
MKIMAGE flash.bin
Error: spl/u-boot-spl.cfgout[16] - Invalid command (LOADER) arch/arm/mach-imx/Makefile:190: recipe for target 'flash.bin' failed make[1]: *** [flash.bin] Error 1
make[1]: *** Deleting file 'flash.bin'
Makefile:1519: recipe for target 'flash.bin' failed
make: *** [flash.bin] Error 2

Quoted 3 lines
Quoted 1 line

Some clue howto fix that?

This might be due to the fact that you're using the same u-boot-nodtb.bin binary twice: once in binman section, and once in ITB. You can try to rename the binman entry to a different name, this might do the trick. See [1] for sample of imx8mq_evk conversion.

ok I think I fixed that. I dropped additionally the following statements:

make u-boot.bin
make flash.bin

just make is enough here or?

But still get this warning even if CONFIG_SPL_FIT_GENERATOR is disabled.

make imx8qm_rom7720_a1_4G_defconfig && make
#

# configuration written to .config
#
scripts/kconfig/conf  --syncconfig Kconfig
  CFG     u-boot.cfg
  GEN     include/autoconf.mk
  GEN     include/autoconf.mk.dep
  CFG     spl/u-boot.cfg
  GEN     spl/include/autoconf.mk
===================== WARNING ======================
This board uses CONFIG_SPL_FIT_GENERATOR. Please migrate
to binman instead, to avoid the proliferation of
arch-specific scripts with no tests.
====================================================
Quoted 3 lines

Is there any documentation available for this board that needs adaptions with new build instructions? I was not able to locate any doc for this board at all...

You find the doc here:

doc/board/advantech/imx8qm-rom7720-a1.rst

Quoted 4 lines

What I see is missing in this section is SECO and SCFW binaries.

Can i.MX8QM boot without those? Otherwise generated image will be unusable.

you are right. This is still missing. Can you point me to a example with SECO and SCFW?

Quoted 6 lines

This binman configuration suggests that there are 2 binaries that should be populated onto the bootable media: flash.bin and u-boot.itb. Can you please convert them to use a single binary? Sample code for this is also in [1].

thx for your suggestions

Best regards,

Oliver

#3 lore raw
In reply to ZHIZHIKIN Andrey

Hi Oliver

Quoted 13 lines · ZHIZHIKIN Andrey

Hello Oliver,

Quoted 11 lines

-----Original Message-----
From: Oliver Graute <[email protected]>
Sent: Monday, January 10, 2022 11:31 AM
To: Oliver Graute <[email protected]>; Stefano Babic <[email protected]>; Fabio Estevam <[email protected]>; NXP i.MX U-Boot Team <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; ZHIZHIKIN Andrey <[email protected]>; [email protected]
Subject: [RFC] imx: imx8qm-rom7720: switch to binman

Quoted 9 lines
Quoted 1 line

Switch to use binman to pack images

Please don't forget S-o-B, checkpatch does complain about it. ;)

Quoted 6 lines

---

Run into this issue on the first try to get binman working:

make[1]: Nothing to be done for 'SPL'.

You may need something similar to [1]

Quoted 9 lines
Quoted 9 lines

  BINMAN  flash.bin
  MKIMAGE flash.bin
Error: spl/u-boot-spl.cfgout[16] - Invalid command (LOADER) arch/arm/mach-imx/Makefile:190: recipe for target 'flash.bin' failed make[1]: *** [flash.bin] Error 1
make[1]: *** Deleting file 'flash.bin'
Makefile:1519: recipe for target 'flash.bin' failed
make: *** [flash.bin] Error 2

Quoted 5 lines
Quoted 1 line

Some clue howto fix that?

This might be due to the fact that you're using the same u-boot-nodtb.bin binary twice: once in binman section, and once in ITB. You can try to rename the binman entry to a different name, this might do the trick. See [1] for sample of imx8mq_evk conversion.

Yep, adding the imx-boot/flash.bin binman section combining them two should avoid this.

To be honest, even on imx8mm it currently fails if doing make flash.bin rather than just make which will call BINMAN ALL. I guess, that might be some kind of a remnant resp. clash with before binman stuff.

⬢[zim@toolbox u-boot.git]$ make verdin-imx8mm_defconfig ⬢[zim@toolbox u-boot.git]$ make -j12 flash.bin
...
BINMAN flash.bin
MKIMAGE flash.bin
./tools/mkimage: Can't open spl/u-boot-spl-ddr.bin: No such file or directory make[1]: *** [arch/arm/mach-imx/Makefile:167: flash.bin] Error 1 make[1]: *** Deleting file 'flash.bin'
make: *** [Makefile:1521: flash.bin] Error 2

Quoted 34 lines
Quoted 5 lines

 arch/arm/dts/imx8qm-rom7720-a1.dts            |  1 + arch/arm/dts/imx8qm-u-boot.dtsi               | 95 +++++++++++++++++++ arch/arm/mach-imx/imx8/Kconfig                |  1 + .../advantech/imx8qm_rom7720_a1/imximage.cfg  | 16 +--- configs/imx8qm_rom7720_a1_4G_defconfig        |  2 +-

Is there any documentation available for this board that needs adaptions with new build instructions? I was not able to locate any doc for this board at all...

Quoted 24 lines
 5 files changed, 100 insertions(+), 15 deletions(-)

 create mode 100644 arch/arm/dts/imx8qm-u-boot.dtsi

arch/arm/dts/imx8qm-rom7720- renamed from arch/arm/dts/imx8qm-rom7720-a1.dts +0 -0

a1.dts
index d1f2fff869..332d441c6d 100644

arch/arm/dts/imx8qm-rom7720-a1.dts +1 -0
@@ -10,6 +10,7 @@
  /memreserve/ 0x80000000 0x00020000;
 
  #include "fsl-imx8qm.dtsi"
+#include "imx8qm-u-boot.dtsi"
 
  / {
         model = "Advantech iMX8QM Qseven series";
arch/arm/dts/imx8qm-u-boot.dtsi new file +2 -0
new file mode 100644
index 0000000000..77e5cd6989
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
Quoted 8 lines

arch/arm/dts/imx8qm-u-boot.dtsi line 10

Quoted 8 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +8 -0
+ * Copyright 2021 NXP
+ */
+
+/ {
+       binman: binman {
+               multiple-images;
+       };
+

Please avoid such empty lines before closing curly braces.

Quoted 63 lines

arch/arm/dts/imx8qm-u-boot.dtsi line 22

Quoted 12 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +12 -0
+};
+
+&binman {
+       u-boot-nodtb {
+               filename = "u-boot-nodtb.bin";
+               pad-byte = <0xff>;
+               align-size = <4>;
+               align = <4>;
+
+               u-boot-spl {
+                       align-end = <4>;
+               };

What I see is missing in this section is SECO and SCFW binaries.

Can i.MX8QM boot without those? Otherwise generated image will be unusable.

Quoted 46 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +6 -0
+
+       };
+
+       flash {
+               mkimage {
+                       args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e

0x100000";

arch/arm/dts/imx8qm-u-boot.dtsi new file +39 -0
+
+                       blob {
+                               filename = "u-boot-nodtb.bin";
+                       };
+
+               };
+
+       };
+
+       itb {
+               filename = "u-boot.itb";
+
+               fit {
+                       description = "Configuration to load ATF before U-Boot";
+                       #address-cells = <1>;
+                       fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;
+
+                       images {
+                               uboot {
+                                       description = "U-Boot (64-bit)";
+                                       type = "standalone";
+                                       arch = "arm64";
+                                       compression = "none";
+                                       load = <CONFIG_SYS_TEXT_BASE>;
+
+                                       uboot_blob: blob-ext {
+                                               filename = "u-boot-nodtb.bin";
+                                       };
+                               };
+
+                               atf {
+                                       description = "ARM Trusted Firmware";
+                                       type = "firmware";
+                                       arch = "arm64";
+                                       compression = "none";
+                                       load = <0x80000000>;
+                                       entry = <0x80000000>;
+
+                                       atf_blob: blob-ext {
Quoted 8 lines
Quoted 6 lines

+                                               filename = "bl31.bin"; +                                       };
+                               };
+
+                               fdt {
+                                       description = "imx8qm-rom7720-a1";

You can use "NAME" here I suppose.

I guess, Andrey meant filename, right?

Anyway, you may want to look at the latest clean-up I did here [2] et al. Otherwise I will have to go through that same clean-up for imx8qm later yet again :-p.

Quoted 26 lines
Quoted 4 lines

+                                       type = "flat_dt"; +                                       compression = "none";

arch/arm/dts/imx8qm-u-boot.dtsi new file +2 -0
+
+                                       uboot_fdt_blob: blob-ext {

arch/arm/dts/imx8qm-u-boot.dtsi line 87

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +10 -0
+                                               filename = "u-boot.dtb";
+                                       };
+                               };
+                       };
+
+                       configurations {
+                               default = "conf";
+
+                               conf {
+                                       description = "imx8qm-rom7720-a1";

And as well here, "NAME".

Quoted 8 lines

+                                       firmware = "uboot"; +                                       loadables = "atf"; +                                       fdt = "fdt"; +                               };
+                       };
+               };
+       };
+};

Quoted 4 lines

This binman configuration suggests that there are 2 binaries that should be populated onto the bootable media: flash.bin and u-boot.itb. Can you please convert them to use a single binary? Sample code for this is also in [1].

I also could not really find such information as at least the address where to put the second part will be crucial.

Quoted 40 lines
Quoted 40 lines
arch/arm/mach-imx/imx8/Kconfig +0 -0
index b43739e5c6..b42b985cdf 100644
@@ -81,6 +81,7 @@ config TARGET_CONGA_QMX8
 

 config TARGET_IMX8QM_ROM7720_A1
        bool "Support i.MX8QM ROM-7720-A1"
+       select BINMAN
        select BOARD_LATE_INIT
        select SUPPORT_SPL
        select IMX8QM

board/advantech/imx8qm_rom7720_a1/imximage.cfg +2 -14
index e324c7ca37..30556ff9d7 100644
@@ -5,17 +5,5 @@
 
  #define __ASSEMBLY__
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000
+BOOT_FROM      sd
+LOADER         u-boot-dtb.bin  0x10000
configs/imx8qm_rom7720_a1_4G_defconfig +0 -0
index fb43fa1962..07ea6e191d 100644
Quoted 8 lines

configs/imx8qm_rom7720_a1_4G_defconfig CONFIG_SPL=y · line 21

Quoted 8 lines
configs/imx8qm_rom7720_a1_4G_defconfig +0 -0
@@ -18,7 +18,7 @@ CONFIG_SPL=y

 CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y

configs/imx8qm_rom7720_a1_4G_defconfig +1 -1
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_SPL_FIT_GENERATOR is not set

I guess, that would likely rather need to be as follows:

# CONFIG_USE_SPL_FIT_GENERATOR is not set

Quoted 9 lines
Quoted 5 lines

 CONFIG_BOOTDELAY=3
 CONFIG_LOG=y
 CONFIG_BOARD_EARLY_INIT_F=y
--
2.17.1

-- andrey

[1] https://source.denx.de/u-boot/u-boot/-/commit/68de913c12c4d091f51009ad6f179fab825d3d82
[2] https://source.denx.de/u-boot/u-boot/-/commit/f17fb6cae4ddaa539f2a49851b112f2d547bbada

Cheers

Marcel

#4 lore raw
Quoted 55 lines · Marcel Ziswiler

Hi Oliver

Quoted 7 lines · ZHIZHIKIN Andrey

Hello Oliver,

Quoted 5 lines

-----Original Message-----
From: Oliver Graute <[email protected]>
Sent: Monday, January 10, 2022 11:31 AM
To: Oliver Graute <[email protected]>; Stefano Babic <[email protected]>; Fabio Estevam <[email protected]>; NXP i.MX U-Boot

Team

Quoted 3 lines
Quoted 3 lines

<[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; ZHIZHIKIN Andrey <

[email protected]>;

Quoted 12 lines
Quoted 4 lines

[email protected]
Subject: [RFC] imx: imx8qm-rom7720: switch to binman

Switch to use binman to pack images

Please don't forget S-o-B, checkpatch does complain about it. ;)

Quoted 6 lines

---

Run into this issue on the first try to get binman working:

make[1]: Nothing to be done for 'SPL'.

You may need something similar to [1]

Quoted 9 lines
Quoted 9 lines

BINMAN flash.bin
MKIMAGE flash.bin
Error: spl/u-boot-spl.cfgout[16] - Invalid command (LOADER) arch/arm/mach-imx/Makefile:190: recipe for target 'flash.bin' failed make[1]: *** [flash.bin] Error 1
make[1]: *** Deleting file 'flash.bin'
Makefile:1519: recipe for target 'flash.bin' failed
make: *** [flash.bin] Error 2

Quoted 3 lines
Quoted 1 line

Some clue howto fix that?

This might be due to the fact that you're using the same

u-boot-nodtb.bin binary twice: once in binman

Quoted 1 line

section, and once in ITB. You can try to rename the binman entry to a

different name, this might do the

Quoted 1 line

trick. See [1] for sample of imx8mq_evk conversion.

Yep, adding the imx-boot/flash.bin binman section combining them two should avoid this.

To be honest, even on imx8mm it currently fails if doing make flash.bin rather than just make which will call
BINMAN ALL. I guess, that might be some kind of a remnant resp. clash with before binman stuff.

Quoted 8 lines

⬢[zim@toolbox u-boot.git]$ make verdin-imx8mm_defconfig ⬢[zim@toolbox u-boot.git]$ make -j12 flash.bin
...
BINMAN flash.bin
MKIMAGE flash.bin
./tools/mkimage: Can't open spl/u-boot-spl-ddr.bin: No such file or directory

When I got this error, I had to double check the imximage-8mm-lpddr4.cfg file referenced from the Kconfig. Beacon has a custom one [1] that doesn't point to spl, and that made this error go away.

[1]
https://source.denx.de/u-boot/u-boot/-/blob/master/board/beacon/imx8mm/imximage-8mm-lpddr4.cfg

Quoted 248 lines

make[1]: *** [arch/arm/mach-imx/Makefile:167: flash.bin] Error 1 make[1]: *** Deleting file 'flash.bin'
make: *** [Makefile:1521: flash.bin] Error 2

Quoted 6 lines
Quoted 5 lines
 arch/arm/dts/imx8qm-rom7720-a1.dts            |  1 +
 arch/arm/dts/imx8qm-u-boot.dtsi               | 95 +++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig                |  1 +
 .../advantech/imx8qm_rom7720_a1/imximage.cfg  | 16 +---
 configs/imx8qm_rom7720_a1_4G_defconfig        |  2 +-
Quoted 8 lines

Is there any documentation available for this board that needs adaptions with new build instructions? I was not able to locate any doc for this board at all...

Review

Quoted 4 lines
 5 files changed, 100 insertions(+), 15 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-u-boot.dtsi
(quoted diff) +0 -0

b/arch/arm/dts/imx8qm-rom7720-

Quoted 7 lines
Quoted 7 lines

a1.dts
index d1f2fff869..332d441c6d 100644

arch/arm/dts/imx8qm-rom7720-a1.dts +0 -0
@@ -10,6 +10,7 @@
 /memreserve/ 0x80000000 0x00020000;
 
Quoted 6 lines

Review

Quoted 6 lines
arch/arm/dts/imx8qm-rom7720-a1.dts +1 -0
 #include "fsl-imx8qm.dtsi"
+#include "imx8qm-u-boot.dtsi"
 
 / {
        model = "Advantech iMX8QM Qseven series";
(quoted diff) +0 -0

b/arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 7 lines
Quoted 7 lines

new file mode 100644
index 0000000000..77e5cd6989

arch/arm/dts/imx8qm-u-boot.dtsi new file +2 -0
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
Quoted 8 lines

arch/arm/dts/imx8qm-u-boot.dtsi line 10

Quoted 8 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +8 -0
+ * Copyright 2021 NXP
+ */
+
+/ {
+       binman: binman {
+               multiple-images;
+       };
+

Please avoid such empty lines before closing curly braces.

Quoted 15 lines

arch/arm/dts/imx8qm-u-boot.dtsi line 22

Quoted 12 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +12 -0
+};
+
+&binman {
+       u-boot-nodtb {
+               filename = "u-boot-nodtb.bin";
+               pad-byte = <0xff>;
+               align-size = <4>;
+               align = <4>;
+
+               u-boot-spl {
+                       align-end = <4>;
+               };

What I see is missing in this section is SECO and SCFW binaries.

Quoted 1 line

Can i.MX8QM boot without those? Otherwise generated image will be

unusable.

Quoted 7 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 7 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +6 -0
+
+       };
+
+       flash {
+               mkimage {
+                       args = "-n spl/u-boot-spl.cfgout -T imx8mimage

-e

Quoted 7 lines
Quoted 7 lines

0x100000";

arch/arm/dts/imx8qm-u-boot.dtsi new file +6 -0
+
+                       blob {
+                               filename = "u-boot-nodtb.bin";
+                       };
+
+               };
Quoted 8 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 8 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +8 -0
+
+       };
+
+       itb {
+               filename = "u-boot.itb";
+
+               fit {
+                       description = "Configuration to load ATF

before U-Boot";

Quoted 2 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 2 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +2 -0
+                       #address-cells = <1>;
+                       fit,external-offset =

<CONFIG_FIT_EXTERNAL_OFFSET>;

Quoted 4 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 4 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +4 -0
+
+                       images {
+                               uboot {
+                                       description = "U-Boot

(64-bit)";

Quoted 7 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 7 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +7 -0
+                                       type = "standalone";
+                                       arch = "arm64";
+                                       compression = "none";
+                                       load = <CONFIG_SYS_TEXT_BASE>;
+
+                                       uboot_blob: blob-ext {
+                                               filename =

"u-boot-nodtb.bin";

Quoted 5 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 5 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +5 -0
+                                       };
+                               };
+
+                               atf {
+                                       description = "ARM Trusted

Firmware";

Quoted 5 lines
Quoted 5 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +5 -0
+                                       type = "firmware";
+                                       arch = "arm64";
+                                       compression = "none";
+                                       load = <0x80000000>;
+                                       entry = <0x80000000>;
Quoted 8 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 8 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +8 -0
+
+                                       atf_blob: blob-ext {
+                                               filename = "bl31.bin";
+                                       };
+                               };
+
+                               fdt {
+                                       description =

"imx8qm-rom7720-a1";

Quoted 2 lines

You can use "NAME" here I suppose.

I guess, Andrey meant filename, right?

Anyway, you may want to look at the latest clean-up I did here [2] et al. Otherwise I will have to go through
that same clean-up for imx8qm later yet again :-p.

Quoted 5 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 5 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +5 -0
+                                       type = "flat_dt";
+                                       compression = "none";
+
+                                       uboot_fdt_blob: blob-ext {
+                                               filename =

"u-boot.dtb";

Quoted 9 lines

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 9 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +9 -0
+                                       };
+                               };
+                       };
+
+                       configurations {
+                               default = "conf";
+
+                               conf {
+                                       description =

"imx8qm-rom7720-a1";

Quoted 12 lines

And as well here, "NAME".

arch/arm/dts/imx8qm-u-boot.dtsi line 95

Quoted 8 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +8 -0
+                                       firmware = "uboot";
+                                       loadables = "atf";
+                                       fdt = "fdt";
+                               };
+                       };
+               };
+       };
+};
Quoted 4 lines

This binman configuration suggests that there are 2 binaries that should be populated onto the bootable media: flash.bin and u-boot.itb. Can you please convert them to use a single binary? Sample code for this is also in [1].

I also could not really find such information as at least the address where to put the second part will be
crucial.

Quoted 1 line

Review

Quoted 1 line
(quoted diff) +0 -0

b/arch/arm/mach-imx/imx8/Kconfig

Quoted 39 lines
Quoted 39 lines

index b43739e5c6..b42b985cdf 100644

arch/arm/mach-imx/imx8/Kconfig +1 -0
@@ -81,6 +81,7 @@ config TARGET_CONGA_QMX8
 
 config TARGET_IMX8QM_ROM7720_A1
        bool "Support i.MX8QM ROM-7720-A1"
+       select BINMAN
        select BOARD_LATE_INIT
        select SUPPORT_SPL
        select IMX8QM
board/advantech/imx8qm_rom7720_a1/imximage.cfg +2 -14
index e324c7ca37..30556ff9d7 100644
@@ -5,17 +5,5 @@
 
 #define __ASSEMBLY__
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000
+BOOT_FROM      sd
+LOADER         u-boot-dtb.bin  0x10000
configs/imx8qm_rom7720_a1_4G_defconfig +0 -0
index fb43fa1962..07ea6e191d 100644
Quoted 8 lines

configs/imx8qm_rom7720_a1_4G_defconfig CONFIG_SPL=y · line 21

Quoted 8 lines
configs/imx8qm_rom7720_a1_4G_defconfig +1 -1
@@ -18,7 +18,7 @@ CONFIG_SPL=y
 CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_SPL_FIT_GENERATOR is not set

I guess, that would likely rather need to be as follows:

# CONFIG_USE_SPL_FIT_GENERATOR is not set

Quoted 9 lines
Quoted 5 lines
configs/imx8qm_rom7720_a1_4G_defconfig +0 -1
 CONFIG_BOOTDELAY=3
 CONFIG_LOG=y
 CONFIG_BOARD_EARLY_INIT_F=y
--

2.17.1

-- andrey

Link [1]:

https://lore.kernel.org/u-boot/[email protected]/

[1]
https://source.denx.de/u-boot/u-boot/-/commit/68de913c12c4d091f51009ad6f179fab825d3d82
[2]
https://source.denx.de/u-boot/u-boot/-/commit/f17fb6cae4ddaa539f2a49851b112f2d547bbada

Cheers

Marcel

#5 lore raw

RFC 1/1 imx: imx8qm-rom7720: switch to binman

In reply to Oliver Graute

Switch to use binman to pack images

---

A flash.bin is now generated by binman but its now bigger then with mkimage_fit_atf.sh 800K vs. 1.1M and is currently NOT booting. So something is still messed up.

 arch/arm/dts/imx8qm-rom7720-a1.dts            |   1 +
 arch/arm/dts/imx8qm-u-boot.dtsi               | 136 ++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig                |   1 +
 .../advantech/imx8qm_rom7720_a1/imximage.cfg  |  16 +--
 configs/imx8qm_rom7720_a1_4G_defconfig        |   2 +-
 doc/board/advantech/imx8qm-rom7720-a1.rst     |   3 +-
 6 files changed, 142 insertions(+), 17 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-u-boot.dtsi
arch/arm/dts/imx8qm-rom7720-a1.dts +1 -0
index d1f2fff869..332d441c6d 100644
@@ -10,6 +10,7 @@
 /memreserve/ 0x80000000 0x00020000;
 
 #include "fsl-imx8qm.dtsi"
+#include "imx8qm-u-boot.dtsi"
 
 / {
 	model = "Advantech iMX8QM Qseven series";
arch/arm/dts/imx8qm-u-boot.dtsi new file +136 -0

136 lines not on this page · raw message

arch/arm/mach-imx/imx8/Kconfig +1 -0
index b43739e5c6..b42b985cdf 100644
@@ -81,6 +81,7 @@ config TARGET_CONGA_QMX8
 
 config TARGET_IMX8QM_ROM7720_A1
 	bool "Support i.MX8QM ROM-7720-A1"
+	select BINMAN
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
 	select IMX8QM
board/advantech/imx8qm_rom7720_a1/imximage.cfg +2 -14
index e324c7ca37..30556ff9d7 100644
@@ -5,17 +5,5 @@
 
 #define __ASSEMBLY__
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000
+BOOT_FROM	sd
+LOADER		u-boot-dtb.bin	0x10000
configs/imx8qm_rom7720_a1_4G_defconfig +1 -1
index fb43fa1962..26afa4f8d7 100644
@@ -18,7 +18,7 @@ CONFIG_SPL=y
 CONFIG_SYS_LOAD_ADDR=0x80280000
 CONFIG_FIT=y
 CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+# CONFIG_USE_SPL_FIT_GENERATOR is not set
 CONFIG_BOOTDELAY=3
 CONFIG_LOG=y
 CONFIG_BOARD_EARLY_INIT_F=y
doc/board/advantech/imx8qm-rom7720-a1.rst +1 -2
index bd4be1dbeb..953cf01fde 100644
@@ -57,8 +57,7 @@ Build U-Boot
      $ export ATF_LOAD_ADDR=0x80000000
      $ export BL33_LOAD_ADDR=0x80020000
      $ make imx8qm_rom7720_a1_4G_defconfig
-     $ make u-boot.bin
-     $ make flash.bin
+     $ make
 
 Flash the binary into the SD card
 ---------------------------------
Signature · 1 line
2.17.1
#6 lore raw
Quoted 57 lines · Oliver Graute

Switch to use binman to pack images

arch/arm/dts/imx8qm-u-boot.dtsi new file +54 -0
+
+			images {
+				uboot {
+					arch = "arm64";
+					compression = "none";
+					description = "U-Boot (64-bit)";
+					load = <CONFIG_SYS_TEXT_BASE>;
+					type = "standalone";
+
+					uboot_blob {
+						filename = "u-boot-nodtb.bin";
+						type = "blob-ext";
+					};
+				};
+
+				atf {
+					arch = "arm64";
+					compression = "none";
+					description = "ARM Trusted Firmware";
+					entry = <0x00910000>;
+					load =  <0x00091000>;
+					type = "firmware";
+
+					atf_blob {
+						filename = "bl31.bin";
+						type = "blob-ext";
+					};
+				};
+
+				scfw {
+					arch = "arm64";
+					compression = "none";
+					description = "System Controler Firmware";
+					type = "firmware";
+
+					scfw_blob {
+						filename = "mx8qm-val-scfw-tcm.bin";
+						type = "blob-ext";
+					};
+				};
+
+				seco {
+					arch = "arm64";
+					compression = "none";
+					description = "Seco Firmware";
+					type = "firmware";
+
+					seco_blob {
+						filename = "mx8qm-ahab-container.img";
+						type = "blob-ext";
+					};
+				};
+
+				fdt {

arch/arm/dts/imx8qm-u-boot.dtsi line 105

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +10 -0
+					filename = "imx8qm-rom7720-a1";
+					type = "flat_dt";
+					compression = "none";
+
+					uboot_fdt_blob {
+						filename = "u-boot.dtb";
+						type = "blob-ext";
+					};
+				};
+			};

As far as I now the order of the blobs for imx8qm is:

1.SECO
2.scfw
3.ATF
4.U-Boot

So do I need to reorder the blobs nodes above? How is the order determined?

Quoted 7 lines

#define __ASSEMBLY__

board/advantech/imx8qm_rom7720_a1/imximage.cfg +0 -4
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM

board/advantech/imx8qm_rom7720_a1/imximage.cfg line 21

Quoted 10 lines
board/advantech/imx8qm_rom7720_a1/imximage.cfg +0 -10
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000

this is what imx-image is doing before. Can someone comment on this?

Best Regards,

Oliver

#7 lore raw
In reply to Oliver Graute
Quoted 53 lines · Oliver Graute

Switch to use binman to pack images

---

A flash.bin is now generated by binman but its now bigger then with mkimage_fit_atf.sh 800K vs. 1.1M and is currently NOT booting. So something is still messed up.

 arch/arm/dts/imx8qm-rom7720-a1.dts            |   1 +
 arch/arm/dts/imx8qm-u-boot.dtsi               | 136 ++++++++++++++++++
 arch/arm/mach-imx/imx8/Kconfig                |   1 +
 .../advantech/imx8qm_rom7720_a1/imximage.cfg  |  16 +--
 configs/imx8qm_rom7720_a1_4G_defconfig        |   2 +-
 doc/board/advantech/imx8qm-rom7720-a1.rst     |   3 +-
 6 files changed, 142 insertions(+), 17 deletions(-)
 create mode 100644 arch/arm/dts/imx8qm-u-boot.dtsi
arch/arm/dts/imx8qm-rom7720-a1.dts +1 -0
index d1f2fff869..332d441c6d 100644
@@ -10,6 +10,7 @@
 /memreserve/ 0x80000000 0x00020000;
 
 #include "fsl-imx8qm.dtsi"
+#include "imx8qm-u-boot.dtsi"
 
 / {
 	model = "Advantech iMX8QM Qseven series";
arch/arm/dts/imx8qm-u-boot.dtsi new file +17 -0
new file mode 100644
index 0000000000..98379516cc
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ */
+
+/ {
+	binman: binman {
+		multiple-images;
+	};
+};
+
+&binman {
+	u-boot {
+		align-size = <4>;
+		align = <4>;
+		filename = "u-boot.bin";
+		pad-byte = <0xff>;

arch/arm/dts/imx8qm-u-boot.dtsi line 27

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +10 -0
+
+		u-boot-spl {
+			align-end = <4>;
+		};
+	};
+
+	spl {
+		filename = "spl.bin";
+		mkimage {
+			args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x100000";

this refers to the wrong container format for imx8qm!
So replacing s/imx8mimage/imx8image/ does help to get a working image.

Quoted 7 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +0 -4
 #define __ASSEMBLY__
 
-/* Boot from SD, sector size 0x400 */
-BOOT_FROM SD 0x400
-/* SoC type IMX8QM */
-SOC_TYPE IMX8QM

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 10 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +0 -10
-/* Append seco container image */
-APPEND mx8qm-ahab-container.img
-/* Create the 2nd container */
-CONTAINER
-/* Add scfw image with exec attribute */
-IMAGE SCU mx8qm-val-scfw-tcm.bin
-/* Add ATF image with exec attribute */
-IMAGE A35 bl31.bin 0x80000000
-/* Add U-Boot image with load attribute */
-DATA A35 u-boot-dtb.bin 0x80020000

I need to keep this here to.

arch/arm/dts/imx8qm-u-boot.dtsi

Quoted 2 lines
arch/arm/dts/imx8qm-u-boot.dtsi new file +2 -0
+BOOT_FROM	sd
+LOADER		u-boot-dtb.bin	0x10000

with this changes the resulting flash.bin is as big as before and its booting flawlessly.

I 'll ppst later a patch v1 for this.

Best regards,

Oliver