Multiple addition to ipq8064 dtsi
Subsystems (2)
cover Multiple addition to ipq8064 dtsi
This try to complete the ipq8064 dtsi and introduce 2 new dtsi ipq8064-v2 and ipq8065. While some node are still missing (cpufreq node, l2 scale node, fab scale node) this would add most of the missing node to make ipq8064 actually usable.
Some of the changes are the fix for the pci IO that cause any secondary wifi card with ath10k to fail init.
Adds regulators definition for RPM.
Adds many missing gsbi nodes used by all the devices.
Enable the usb phy by default as they are actually enabled internally by xlate only if the dwc3 driver is used.
Add opp table and declare idle state for ipq8064.
Fix some dtc warning.
This also add the ipq8064-v2.0 dtsi and the ipq8065 dtsi used by more recent devices based on this SoC.
Ansuel Smith (17):
ARM: dts: qcom: add multiple missing pin definition for ipq8064
ARM: dts: qcom: add gsbi6 missing definition for ipq8064
ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
ARM: dts: qcom: add missing snps,dwmac compatible for gmac ipq8064
ARM: dts: qcom: enable usb phy by default for ipq8064
ARM: dts: qcom: reduce pci IO size to 64K for ipq8064
ARM: dts: qcom: fix dtc warning for missing #address-cells for ipq8064
ARM: dts: qcom: add smem node for ipq8064
ARM: dts: qcom: add saw for l2 cache and kraitcc for ipq8064
ARM: dts: qcom: add sic non secure node for ipq8064
ARM: dts: qcom: fix and add some missing gsbi node for ipq8064
ARM: dts: qcom: add opp table for cpu and l2 for ipq8064
ARM: dts: qcom: add speedbin efuse nvmem binding
ARM: dts: qcom: add multiple missing binding for cpu and l2 for
ipq8064
ARM: dts: qcom: remove redundant binding from ipq8064 rb3011 dts
ARM: dts: qcom: add ipq8064-v2.0 dtsi
ARM: dts: qcom: add ipq8065 dtsi
arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 17 -- arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi | 70 +++++ arch/arm/boot/dts/qcom-ipq8064.dtsi | 344 +++++++++++++++++++++- arch/arm/boot/dts/qcom-ipq8065.dtsi | 168 +++++++++++ 4 files changed, 568 insertions(+), 31 deletions(-) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi create mode 100644 arch/arm/boot/dts/qcom-ipq8065.dtsi
Signature · 1 line
2.33.1
PATCH 1/17 ARM: dts: qcom: add multiple missing pin definition for ipq8064
Add missing definition for mdio0 pins used for gpio-bitbang driver,i2c4 pins and rgmii2 pins for ipq8064.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 34 +++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +34 -0
@@ -382,6 +382,15 @@ mux { }; }; + i2c4_pins: i2c4_pinmux { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + spi_pins: spi_pins { mux { pins = "gpio18", "gpio19", "gpio21";
@@ -424,6 +433,8 @@ mux { pullups { pins = "gpio39"; + function = "nand"; + drive-strength = <10>; bias-pull-up; };
@@ -431,9 +442,32 @@ hold { pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44", "gpio45", "gpio46", "gpio47"; + function = "nand"; + drive-strength = <10>; bias-bus-hold; }; }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "mdio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", + "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", + "gpio60", "gpio61", "gpio62"; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; }; intc: interrupt-controller@2000000 {
Signature · 1 line
2.33.1
PATCH 2/17 ARM: dts: qcom: add gsbi6 missing definition for ipq8064
In reply to Ansuel SmithAdd gsbi6 missing definition for ipq8064.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +27 -0
@@ -665,6 +665,33 @@ spi@1a280000 { }; }; + gsbi6: gsbi@16500000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <6>; + reg = <0x16500000 0x100>; + clocks = <&gcc GSBI6_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon-tcsr = <&tcsr>; + + gsbi6_i2c: i2c@16580000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16580000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; + }; + gsbi7: gsbi@16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0";
Signature · 1 line
2.33.1
Re: [PATCH 02/17] ARM: dts: qcom: add gsbi6 missing definition for ipq8064
Quoted 30 lines · Ansuel Smith
Add gsbi6 missing definition for ipq8064.
Signed-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 27 +++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +15
-0@@ -665,6 +665,33 @@ spi@1a280000 { }; }; + gsbi6: gsbi@16500000 { + status = "disabled"; + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <6>; + reg = <0x16500000 0x100>; + clocks = <&gcc GSBI6_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + syscon-tcsr = <&tcsr>; + + gsbi6_i2c: i2c@16580000 { + compatible = "qcom,i2c-qup-v1.1.1";
arch/arm/boot/dts/qcom-ipq8064.dtsi spi@1a280000 { · line 692
Quoted 10 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +10
-0+ reg = <0x16580000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + };
Can you include the SPI definition too? The RB3011 has its SPI LCD living here.
gsbi6_spi: spi@16580000 {
compatible = "qcom,spi-qup-v1.1.1";
reg = <0x16580000 0x1000>;
interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};Quoted 8 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +2
-0+ }; + gsbi7: gsbi@16600000 { status = "disabled"; compatible = "qcom,gsbi-v1.0.0";Signature · 1 line
2.33.1
J.
Signature · 4 lines
] https://www.earth.li/~noodles/ [] "send me the rhubarb" -- Martin [ ] PGP/GPG Key @ the.earth.li [] Brooks on the risks of dog poo in [ ] via keyserver, web or email. [] compost [ ] RSA: 4096/0x94FA372B2DA8B985 [] [
PATCH 3/17 ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
In reply to Ansuel SmithAdd cells definition for rpm node and add missing regulators for the 4 regulator present on ipq8064. There regulators are controlled by rpm and to correctly works gsbi4_i2c require to be NEVER disabled or rpm will reject any regulator change request.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +35 -0
@@ -829,10 +829,45 @@ rpm: rpm@108000 { clocks = <&gcc RPM_MSG_RAM_H_CLK>; clock-names = "ram"; + #address-cells = <1>; + #size-cells = <0>; + rpmcc: clock-controller { compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; #clock-cells = <1>; }; + + regulators { + compatible = "qcom,rpm-smb208-regulators"; + + smb208_s1a: s1a { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s1b: s1b { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2a: s2a { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2b: s2b { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + }; }; tcsr: syscon@1a400000 {
Signature · 1 line
2.33.1
Re: [PATCH 03/17] ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
Quoted 5 lines · Ansuel Smith
Add cells definition for rpm node and add missing regulators for the 4 regulator present on ipq8064. There regulators are controlled by rpm and to correctly works
gsbi4_i2crequire to be NEVER disabled or rpm will reject any regulator change request.
Is the SMB208 mandatory on all ipq8064 designs, or should this be pushed out to the device dts?
Regards,
Bjorn
Quoted 58 lines
Signed-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +35
-0@@ -829,10 +829,45 @@ rpm: rpm@108000 { clocks = <&gcc RPM_MSG_RAM_H_CLK>; clock-names = "ram"; + #address-cells = <1>; + #size-cells = <0>; + rpmcc: clock-controller { compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; #clock-cells = <1>; }; + + regulators { + compatible = "qcom,rpm-smb208-regulators"; + + smb208_s1a: s1a { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s1b: s1b { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2a: s2a { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2b: s2b { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + }; }; tcsr: syscon@1a400000 {Signature · 1 line
2.33.1
Re: [PATCH 03/17] ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
Quoted 10 lines · Bjorn Andersson
Quoted 5 lines · Ansuel Smith
Add cells definition for rpm node and add missing regulators for the 4 regulator present on ipq8064. There regulators are controlled by rpm and to correctly works
gsbi4_i2crequire to be NEVER disabled or rpm will reject any regulator change request.Is the SMB208 mandatory on all ipq8064 designs, or should this be pushed out to the device dts?
It's not; the RB3011 uses a different regulator (a TPS563900).
Quoted 54 lines
Quoted 54 lines
Signed-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +35
-0@@ -829,10 +829,45 @@ rpm: rpm@108000 { clocks = <&gcc RPM_MSG_RAM_H_CLK>; clock-names = "ram"; + #address-cells = <1>; + #size-cells = <0>; + rpmcc: clock-controller { compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; #clock-cells = <1>; }; + + regulators { + compatible = "qcom,rpm-smb208-regulators"; + + smb208_s1a: s1a { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s1b: s1b { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2a: s2a { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2b: s2b { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + }; };
Quoted 4 lines
Quoted 4 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +0
-0tcsr: syscon@1a400000 {Signature · 1 line
2.33.1
J.
Signature · 2 lines
... "There's no money, there's no weed. It's all been replaced by a fucking
big pile of corpses." -- Lock, Stock and Two Smoking BarrelsRe: [PATCH 03/17] ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
Quoted 9 lines · Jonathan McDowell
Quoted 8 lines · Bjorn Andersson
Quoted 5 lines · Ansuel Smith
Add cells definition for rpm node and add missing regulators for the 4 regulator present on ipq8064. There regulators are controlled by rpm and to correctly works
gsbi4_i2crequire to be NEVER disabled or rpm will reject any regulator change request.
Quoted 5 lines
Quoted 2 lines
Is the SMB208 mandatory on all ipq8064 designs, or should this be pushed out to the device dts?
It's not; the RB3011 uses a different regulator (a TPS563900).
Fact is that that's a special case. We have 20 devices based on ipq806x and they all have smb208 regulators.
Is the TPS563900 also controlled by rpm?
Anyway should we use a dedicated dtsi to declare the correct regulators?
Quoted 64 lines
Quoted 54 lines
Quoted 54 lines
Signed-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +35
-0@@ -829,10 +829,45 @@ rpm: rpm@108000 { clocks = <&gcc RPM_MSG_RAM_H_CLK>; clock-names = "ram"; + #address-cells = <1>; + #size-cells = <0>; + rpmcc: clock-controller { compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; #clock-cells = <1>; }; + + regulators { + compatible = "qcom,rpm-smb208-regulators"; + + smb208_s1a: s1a { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s1b: s1b { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2a: s2a { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2b: s2b { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + }; };Quoted 4 lines
Quoted 4 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +0
-0tcsr: syscon@1a400000 {Signature · 1 line
2.33.1J.
Signature · 2 lines
... "There's no money, there's no weed. It's all been replaced by a fucking big pile of corpses." -- Lock, Stock and Two Smoking Barrels
Signature · 1 line
Ansuel
Re: [PATCH 03/17] ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
Quoted 10 lines · Ansuel Smith
Quoted 9 lines · Jonathan McDowell
Quoted 8 lines · Bjorn Andersson
Quoted 5 lines · Ansuel Smith
Add cells definition for rpm node and add missing regulators for the 4 regulator present on ipq8064. There regulators are controlled by rpm and to correctly works
gsbi4_i2crequire to be NEVER disabled or rpm will reject any regulator change request.
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
Is the SMB208 mandatory on all ipq8064 designs, or should this be pushed out to the device dts?
It's not; the RB3011 uses a different regulator (a TPS563900).
Fact is that that's a special case. We have 20 devices based on ipq806x and they all have smb208 regulators.
Indeed, it's another Mikrotik special unfortunately (I haven't managed to get the SMEM driver to work on the platform either).
Quoted 1 line
Is the TPS563900 also controlled by rpm?
AFAICT it's CPU controlled via I2C. It looks like one output is shared for the CPU cores etc and the other is for the NSS cores, rather than the full control the smb208 offers.
Quoted 1 line
Anyway should we use a dedicated dtsi to declare the correct regulators?
I've got no problem with smb208 being the default, but please add any appropriate disabling of it to the RB3011 DTS.
Quoted 54 lines
Quoted 54 lines
Quoted 54 lines
Quoted 54 lines
Signed-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +35
-0@@ -829,10 +829,45 @@ rpm: rpm@108000 { clocks = <&gcc RPM_MSG_RAM_H_CLK>; clock-names = "ram"; + #address-cells = <1>; + #size-cells = <0>; + rpmcc: clock-controller { compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; #clock-cells = <1>; }; + + regulators { + compatible = "qcom,rpm-smb208-regulators"; + + smb208_s1a: s1a { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s1b: s1b { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1150000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2a: s2a { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + + smb208_s2b: s2b { + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1250000>; + + qcom,switch-mode-frequency = <1200000>; + }; + }; };
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
arch/arm/boot/dts/qcom-ipq8064.dtsi +0
-0tcsr: syscon@1a400000 {Signature · 1 line
2.33.1
J.
Signature · 3 lines
/-\ | 101 things you can't have too much |@/ Debian GNU/Linux Developer | of : 13 - Holidays. \- |
PATCH 4/17 ARM: dts: qcom: add missing snps,dwmac compatible for gmac ipq8064
In reply to Ansuel SmithAdd missing snps,dwmac compatible for gmac ipq8064 dtsi.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +4 -4
@@ -1061,7 +1061,7 @@ stmmac_axi_setup: stmmac-axi-config { gmac0: ethernet@37000000 { device_type = "network"; - compatible = "qcom,ipq806x-gmac"; + compatible = "qcom,ipq806x-gmac", "snps,dwmac"; reg = <0x37000000 0x200000>; interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq";
@@ -1085,7 +1085,7 @@ gmac0: ethernet@37000000 { gmac1: ethernet@37200000 { device_type = "network"; - compatible = "qcom,ipq806x-gmac"; + compatible = "qcom,ipq806x-gmac", "snps,dwmac"; reg = <0x37200000 0x200000>; interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq";
@@ -1109,7 +1109,7 @@ gmac1: ethernet@37200000 { gmac2: ethernet@37400000 { device_type = "network"; - compatible = "qcom,ipq806x-gmac"; + compatible = "qcom,ipq806x-gmac", "snps,dwmac"; reg = <0x37400000 0x200000>; interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq";
@@ -1133,7 +1133,7 @@ gmac2: ethernet@37400000 { gmac3: ethernet@37600000 { device_type = "network"; - compatible = "qcom,ipq806x-gmac"; + compatible = "qcom,ipq806x-gmac", "snps,dwmac"; reg = <0x37600000 0x200000>; interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq";
Signature · 1 line
2.33.1
PATCH 5/17 ARM: dts: qcom: enable usb phy by default for ipq8064
In reply to Ansuel SmithEnable usb phy by default. When the usb phy were pushed, half of them were flagged as disabled by mistake. Fix this to correctly init dwc3 node on any ipq8064 based SoC.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 4 ---- 1 file changed, 4 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +0 -4
@@ -1161,8 +1161,6 @@ hs_phy_0: phy@100f8800 { clocks = <&gcc USB30_0_UTMI_CLK>; clock-names = "ref"; #phy-cells = <0>; - - status = "disabled"; }; ss_phy_0: phy@100f8830 {
@@ -1171,8 +1169,6 @@ ss_phy_0: phy@100f8830 { clocks = <&gcc USB30_0_MASTER_CLK>; clock-names = "ref"; #phy-cells = <0>; - - status = "disabled"; }; usb3_0: usb3@100f8800 {
Signature · 1 line
2.33.1
PATCH 6/17 ARM: dts: qcom: reduce pci IO size to 64K for ipq8064
In reply to Ansuel SmithThe current value for pci IO is problematic for ath10k wifi card commonly connected to ipq8064 SoC.
The current value is probably a typo and is actually uncommon to find 1MB IO space even on a x86 arch. Also with recent changes to the pci driver, pci1 and pci2 now fails to function as any connected device fails any reg read/write. Reduce this to 64K as it should be more than enough and 3 * 64K of total IO space doesn't exceed the IO_SPACE_LIMIT hardcoded for the ARM arch.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +3 -3
@@ -904,7 +904,7 @@ pcie0: pci@1b500000 { #address-cells = <3>; #size-cells = <2>; - ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ + ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
@@ -955,7 +955,7 @@ pcie1: pci@1b700000 { #address-cells = <3>; #size-cells = <2>; - ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ + ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
@@ -1006,7 +1006,7 @@ pcie2: pci@1b900000 { #address-cells = <3>; #size-cells = <2>; - ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ + ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
Signature · 1 line
2.33.1
PATCH 7/17 ARM: dts: qcom: fix dtc warning for missing #address-cells for ipq8064
In reply to Ansuel SmithFix dtc warning for missing #address-cells for ipq8064.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +2 -0
@@ -352,6 +352,7 @@ qcom_pinmux: pinmux@800000 { gpio-ranges = <&qcom_pinmux 0 0 69>; #gpio-cells = <2>; interrupt-controller; + #address-cells = <0>; #interrupt-cells = <2>; interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
@@ -473,6 +474,7 @@ mux { intc: interrupt-controller@2000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; + #address-cells = <0>; #interrupt-cells = <3>; reg = <0x02000000 0x1000>, <0x02002000 0x1000>;
Signature · 1 line
2.33.1
PATCH 8/17 ARM: dts: qcom: add smem node for ipq8064
In reply to Ansuel SmithAdd missing smem node for ipq8064.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +18 -0
@@ -892,6 +892,11 @@ lcc: clock-controller@28000000 { #reset-cells = <1>; }; + sfpb_mutex_block: syscon@1200600 { + compatible = "syscon"; + reg = <0x01200600 0x100>; + }; + pcie0: pci@1b500000 { compatible = "qcom,pcie-ipq8064"; reg = <0x1b500000 0x1000
@@ -1316,4 +1321,17 @@ sdcc3: mmc@12180000 { }; }; }; + + sfpb_mutex: sfpb-mutex { + compatible = "qcom,sfpb-mutex"; + syscon = <&sfpb_mutex_block 4 4>; + + #hwlock-cells = <1>; + }; + + smem { + compatible = "qcom,smem"; + memory-region = <&smem>; + hwlocks = <&sfpb_mutex 3>; + }; };
Signature · 1 line
2.33.1
PATCH 9/17 ARM: dts: qcom: add saw for l2 cache and kraitcc for ipq8064
In reply to Ansuel SmithAdd saw compatible for l2 cache and kraitcc node for ipq8064 dtsi. Also declare clock-output-names for acc0 and acc1.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 17 +++++++++++++++-- 1 file changed, 15 insertions(+), 2 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +15 -2
@@ -504,11 +504,13 @@ IRQ_TYPE_EDGE_RISING)>, acc0: clock-controller@2088000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02088000 0x1000>, <0x02008000 0x1000>; + clock-output-names = "acpu0_aux"; }; acc1: clock-controller@2098000 { compatible = "qcom,kpss-acc-v1"; reg = <0x02098000 0x1000>, <0x02008000 0x1000>; + clock-output-names = "acpu1_aux"; }; adm_dma: dma-controller@18300000 {
@@ -532,17 +534,23 @@ adm_dma: dma-controller@18300000 { }; saw0: regulator@2089000 { - compatible = "qcom,saw2"; + compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; reg = <0x02089000 0x1000>, <0x02009000 0x1000>; regulator; }; saw1: regulator@2099000 { - compatible = "qcom,saw2"; + compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon"; reg = <0x02099000 0x1000>, <0x02009000 0x1000>; regulator; }; + saw_l2: regulator@02012000 { + compatible = "qcom,saw2", "syscon"; + reg = <0x02012000 0x1000>; + regulator; + }; + gsbi2: gsbi@12480000 { compatible = "qcom,gsbi-v1.0.0"; cell-index = <2>;
@@ -885,6 +893,11 @@ l2cc: clock-controller@2011000 { clock-output-names = "acpu_l2_aux"; }; + kraitcc: clock-controller { + compatible = "qcom,krait-cc-v1"; + #clock-cells = <1>; + }; + lcc: clock-controller@28000000 { compatible = "qcom,lcc-ipq8064"; reg = <0x28000000 0x1000>;
Signature · 1 line
2.33.1
PATCH 10/17 ARM: dts: qcom: add sic non secure node for ipq8064
In reply to Ansuel SmithAdd missing sic non secure node for ipq8064.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +5 -0
@@ -551,6 +551,11 @@ saw_l2: regulator@02012000 { regulator; }; + sic_non_secure: sic-non-secure@12100000 { + compatible = "syscon"; + reg = <0x12100000 0x10000>; + }; + gsbi2: gsbi@12480000 { compatible = "qcom,gsbi-v1.0.0"; cell-index = <2>;
Signature · 1 line
2.33.1
PATCH 11/17 ARM: dts: qcom: fix and add some missing gsbi node for ipq8064
In reply to Ansuel SmithAdd some tag for gsbi to make them usable for ipq8064 SoC. Add missing gsbi7 i2c node and gsbi1 node.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 50 ++++++++++++++++++++++++++++- 1 file changed, 49 insertions(+), 1 deletion(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +49 -1
@@ -556,6 +556,41 @@ sic_non_secure: sic-non-secure@12100000 { reg = <0x12100000 0x10000>; }; + gsbi1: gsbi@12440000 { + compatible = "qcom,gsbi-v1.0.0"; + cell-index = <1>; + reg = <0x12440000 0x100>; + clocks = <&gcc GSBI1_H_CLK>; + clock-names = "iface"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + status = "disabled"; + + syscon-tcsr = <&tcsr>; + + gsbi1_serial: serial@12450000 { + compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; + reg = <0x12450000 0x100>, + <0x12400000 0x03>; + interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + gsbi1_i2c: i2c@12460000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x12460000 0x1000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + gsbi2: gsbi@12480000 { compatible = "qcom,gsbi-v1.0.0"; cell-index = <2>;
@@ -579,7 +614,7 @@ gsbi2_serial: serial@12490000 { status = "disabled"; }; - i2c@124a0000 { + gsbi2_i2c: i2c@124a0000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x124a0000 0x1000>; interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
@@ -728,6 +763,19 @@ gsbi7_serial: serial@16640000 { clock-names = "core", "iface"; status = "disabled"; }; + + gsbi7_i2c: i2c@16680000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x16680000 0x1000>; + interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + }; }; rng@1a500000 {
Signature · 1 line
2.33.1
PATCH 12/17 ARM: dts: qcom: add opp table for cpu and l2 for ipq8064
In reply to Ansuel SmithAdd opp table for cpu and l2 cache. The l2 cache won't work as it would require a dedicated cpufreq driver to scale cache with core.
Opp-level is set based on the logic of
0: idle level
1: normal level
2: turbo level
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 99 +++++++++++++++++++++++++++++ 1 file changed, 99 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +99 -0
@@ -48,6 +48,105 @@ L2: l2-cache { }; }; + opp_table_l2: opp_table_l2 { + compatible = "operating-points-v2"; + + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <100000>; + opp-level = <0>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <1150000>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + }; + + opp_table0: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + + /* + * Voltage thresholds are <target min max> + */ + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>; + opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <0>; + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>; + opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>; + opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>; + opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + }; + thermal-zones { sensor0-thermal { polling-delay-passive = <0>;
Signature · 1 line
2.33.1
Re: [PATCH 12/17] ARM: dts: qcom: add opp table for cpu and l2 for ipq8064
Quoted 3 lines · Ansuel Smith
Add opp table for cpu and l2 cache. The l2 cache won't work as it would require a dedicated cpufreq driver to scale cache with core.
Are you saying that the L2 cache frequency scaling doesn't work so you put it there for completeness sake, or that it doesn't work without this patch?
Could you please rewrite this to make it clear in the git history?
Thanks,
Bjorn
Quoted 123 lines
Opp-level is set based on the logic of
0: idle level
1: normal level
2: turbo levelSigned-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 99 +++++++++++++++++++++++++++++ 1 file changed, 99 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +99
-0@@ -48,6 +48,105 @@ L2: l2-cache { }; }; + opp_table_l2: opp_table_l2 { + compatible = "operating-points-v2"; + + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <100000>; + opp-level = <0>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <1150000>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + }; + + opp_table0: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + + /* + * Voltage thresholds are <target min max> + */ + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>; + opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <0>; + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>; + opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>; + opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>; + opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + }; + thermal-zones { sensor0-thermal { polling-delay-passive = <0>;Signature · 1 line
2.33.1
Re: [PATCH 12/17] ARM: dts: qcom: add opp table for cpu and l2 for ipq8064
Quoted 10 lines · Bjorn Andersson
Quoted 3 lines · Ansuel Smith
Add opp table for cpu and l2 cache. The l2 cache won't work as it would require a dedicated cpufreq driver to scale cache with core.
Are you saying that the L2 cache frequency scaling doesn't work so you put it there for completeness sake, or that it doesn't work without this patch?
I put it here for completeness sake. A driver should use the opp table anyway, so I case I manage to make the cpufreq accepted upstream this is already present and can be used directly.
Quoted 2 lines
Could you please rewrite this to make it clear in the git history?
Hope it's not a problem, in theory should be correct to put it anyway as it does describe how the device works.
Quoted 126 lines
Thanks,
BjornQuoted 123 lines
Opp-level is set based on the logic of
0: idle level
1: normal level
2: turbo levelSigned-off-by Ansuel Smith <[email protected]>--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 99 +++++++++++++++++++++++++++++ 1 file changed, 99 insertions(+)arch/arm/boot/dts/qcom-ipq8064.dtsi +99
-0@@ -48,6 +48,105 @@ L2: l2-cache { }; }; + opp_table_l2: opp_table_l2 { + compatible = "operating-points-v2"; + + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <100000>; + opp-level = <0>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt = <1100000>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt = <1150000>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + }; + + opp_table0: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + + /* + * Voltage thresholds are <target min max> + */ + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs1-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs2-v0 = <875000 831250 918750>; + opp-microvolt-speed0-pvs3-v0 = <800000 760000 840000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <0>; + }; + + opp-600000000 { + opp-hz = /bits/ 64 <600000000>; + opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs3-v0 = <850000 807500 892500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-800000000 { + opp-hz = /bits/ 64 <800000000>; + opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs2-v0 = <995000 945250 1044750>; + opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1000000000 { + opp-hz = /bits/ 64 <1000000000>; + opp-microvolt-speed0-pvs0-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs2-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs3-v0 = <950000 902500 997500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <1>; + }; + + opp-1200000000 { + opp-hz = /bits/ 64 <1200000000>; + opp-microvolt-speed0-pvs0-v0 = <1200000 1140000 1260000>; + opp-microvolt-speed0-pvs1-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs2-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs3-v0 = <1000000 950000 1050000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt-speed0-pvs0-v0 = <1250000 1187500 1312500>; + opp-microvolt-speed0-pvs1-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs3-v0 = <1050000 997500 1102500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; + }; + thermal-zones { sensor0-thermal { polling-delay-passive = <0>;Signature · 1 line
2.33.1
Signature · 1 line
Ansuel
PATCH 13/16 ARM: dts: qcom: add multiple missing binding for cpu and l2 for ipq8064
In reply to Ansuel SmithAdd multiple binding for cpu node, l2 node and add idle-states definition for ipq8064 dtsi.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 36 +++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +36 -0
@@ -30,6 +30,16 @@ cpu0: cpu@0 { next-level-cache = <&L2>; qcom,acc = <&acc0>; qcom,saw = <&saw0>; + clocks = <&kraitcc 0>, <&kraitcc 4>; + clock-names = "cpu", "l2"; + clock-latency = <100000>; + cpu-supply = <&smb208_s2a>; + operating-points-v2 = <&opp_table0>; + voltage-tolerance = <5>; + cooling-min-state = <0>; + cooling-max-state = <10>; + #cooling-cells = <2>; + cpu-idle-states = <&CPU_SPC>; }; cpu1: cpu@1 {
@@ -40,11 +50,37 @@ cpu1: cpu@1 { next-level-cache = <&L2>; qcom,acc = <&acc1>; qcom,saw = <&saw1>; + clocks = <&kraitcc 1>, <&kraitcc 4>; + clock-names = "cpu", "l2"; + clock-latency = <100000>; + cpu-supply = <&smb208_s2b>; + operating-points-v2 = <&opp_table0>; + voltage-tolerance = <5>; + cooling-min-state = <0>; + cooling-max-state = <10>; + #cooling-cells = <2>; + cpu-idle-states = <&CPU_SPC>; + }; + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc"; + status = "disabled"; + entry-latency-us = <400>; + exit-latency-us = <900>; + min-residency-us = <3000>; + }; }; L2: l2-cache { compatible = "cache"; cache-level = <2>; + qcom,saw = <&saw_l2>; + + clocks = <&kraitcc 4>; + clock-names = "l2"; + l2-supply = <&smb208_s1a>; + operating-points-v2 = <&opp_table_l2>; }; };
Signature · 1 line
2.33.1
PATCH 13/17 ARM: dts: qcom: add speedbin efuse nvmem binding
In reply to Ansuel SmithAdd speedbin efuse nvmem binding needed for the opp table for the CPU freqs.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +3 -0
@@ -956,6 +956,9 @@ tsens_calib: calib@400 { tsens_calib_backup: calib_backup@410 { reg = <0x410 0xb>; }; + speedbin_efuse: speedbin@0c0 { + reg = <0x0c0 0x4>; + }; }; gcc: clock-controller@900000 {
Signature · 1 line
2.33.1
PATCH 14/17 ARM: dts: qcom: add multiple missing binding for cpu and l2 for ipq8064
In reply to Ansuel SmithAdd multiple binding for cpu node, l2 node and add idle-states definition for ipq8064 dtsi.
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 36 +++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+)
arch/arm/boot/dts/qcom-ipq8064.dtsi +36 -0
@@ -30,6 +30,16 @@ cpu0: cpu@0 { next-level-cache = <&L2>; qcom,acc = <&acc0>; qcom,saw = <&saw0>; + clocks = <&kraitcc 0>, <&kraitcc 4>; + clock-names = "cpu", "l2"; + clock-latency = <100000>; + cpu-supply = <&smb208_s2a>; + operating-points-v2 = <&opp_table0>; + voltage-tolerance = <5>; + cooling-min-state = <0>; + cooling-max-state = <10>; + #cooling-cells = <2>; + cpu-idle-states = <&CPU_SPC>; }; cpu1: cpu@1 {
@@ -40,11 +50,37 @@ cpu1: cpu@1 { next-level-cache = <&L2>; qcom,acc = <&acc1>; qcom,saw = <&saw1>; + clocks = <&kraitcc 1>, <&kraitcc 4>; + clock-names = "cpu", "l2"; + clock-latency = <100000>; + cpu-supply = <&smb208_s2b>; + operating-points-v2 = <&opp_table0>; + voltage-tolerance = <5>; + cooling-min-state = <0>; + cooling-max-state = <10>; + #cooling-cells = <2>; + cpu-idle-states = <&CPU_SPC>; + }; + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc"; + status = "disabled"; + entry-latency-us = <400>; + exit-latency-us = <900>; + min-residency-us = <3000>; + }; }; L2: l2-cache { compatible = "cache"; cache-level = <2>; + qcom,saw = <&saw_l2>; + + clocks = <&kraitcc 4>; + clock-names = "l2"; + l2-supply = <&smb208_s1a>; + operating-points-v2 = <&opp_table_l2>; }; };
Signature · 1 line
2.33.1
PATCH 14/16 ARM: dts: qcom: remove redundant binding from ipq8064 rb3011 dts
In reply to Ansuel SmithMdio0_pins are now declared in ipq8064 dtsi. Usb phy are enabled by default.
--- arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 17 ----------------- 1 file changed, 17 deletions(-)
arch/arm/boot/dts/qcom-ipq8064-rb3011.dts +0 -17
@@ -255,10 +255,6 @@ &gsbi7_serial { status = "okay"; }; -&hs_phy_1 { - status = "okay"; -}; - &nand { status = "okay";
@@ -305,15 +301,6 @@ mux { }; }; - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - mdio1_pins: mdio1_pins { mux { pins = "gpio10", "gpio11";
@@ -354,10 +341,6 @@ mux { }; }; -&ss_phy_1 { - status = "okay"; -}; - &usb3_1 { pinctrl-0 = <&usb1_pwr_en_pins>; pinctrl-names = "default";
Signature · 1 line
2.33.1
PATCH 15/16 ARM: dts: qcom: add ipq8064-v2.0 dtsi
In reply to Ansuel SmithMany devices are based on the v2.0 of the ipq8064 SoC. Main difference is a change in the pci compatible and different way to configre the usb phy.
--- arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi | 70 ++++++++++++++++++++++++ 1 file changed, 70 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi
arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi new file +70 -0
@@ -0,0 +1,70 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "qcom-ipq8064.dtsi" + +/ { + aliases { + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&gsbi4 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "okay"; + + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&CPU_SPC { + status = "okay"; +}; + +&pcie0 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie1 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie2 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&sata { + ports-implemented = <0x1>; +}; + +&ss_phy_0 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&ss_phy_1 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +};
Signature · 1 line
2.33.1
PATCH 15/17 ARM: dts: qcom: remove redundant binding from ipq8064 rb3011 dts
In reply to Ansuel SmithMdio0_pins are now declared in ipq8064 dtsi. Usb phy are enabled by default.
--- arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 17 ----------------- 1 file changed, 17 deletions(-)
arch/arm/boot/dts/qcom-ipq8064-rb3011.dts +0 -17
@@ -255,10 +255,6 @@ &gsbi7_serial { status = "okay"; }; -&hs_phy_1 { - status = "okay"; -}; - &nand { status = "okay";
@@ -305,15 +301,6 @@ mux { }; }; - mdio0_pins: mdio0_pins { - mux { - pins = "gpio0", "gpio1"; - function = "gpio"; - drive-strength = <8>; - bias-disable; - }; - }; - mdio1_pins: mdio1_pins { mux { pins = "gpio10", "gpio11";
@@ -354,10 +341,6 @@ mux { }; }; -&ss_phy_1 { - status = "okay"; -}; - &usb3_1 { pinctrl-0 = <&usb1_pwr_en_pins>; pinctrl-names = "default";
Signature · 1 line
2.33.1
PATCH 16/17 ARM: dts: qcom: add ipq8064-v2.0 dtsi
In reply to Ansuel SmithMany devices are based on the v2.0 of the ipq8064 SoC. Main difference is a change in the pci compatible and different way to configre the usb phy.
--- arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi | 70 ++++++++++++++++++++++++ 1 file changed, 70 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi
arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi new file +70 -0
@@ -0,0 +1,70 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "qcom-ipq8064.dtsi" + +/ { + aliases { + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&gsbi4 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "okay"; + + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&CPU_SPC { + status = "okay"; +}; + +&pcie0 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie1 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie2 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&sata { + ports-implemented = <0x1>; +}; + +&ss_phy_0 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&ss_phy_1 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +};
Signature · 1 line
2.33.1
PATCH 16/16 ARM: dts: qcom: add ipq8065 dtsi
In reply to Ansuel SmithMany device are based on ipq8065 SoC. Ipq8065 is an evolution of the ipq8064 SoC (also named ipq8064-v3.0 from qsdk) that has all the improvement from ipq8064-v2.0 with the addition of a more powerful CPU that can now be clocked to 1.7Ghz, a quicker L2 cache that can be clocked to 1.4Ghz. It also shipped with more powerful regulators to provide the required voltage to the CPUs and L2.
--- arch/arm/boot/dts/qcom-ipq8065.dtsi | 168 ++++++++++++++++++++++++++++ 1 file changed, 168 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8065.dtsi
arch/arm/boot/dts/qcom-ipq8065.dtsi new file +168 -0
@@ -0,0 +1,168 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "qcom-ipq8064.dtsi" + +/ { + model = "Qualcomm IPQ8065"; + compatible = "qcom,ipq8065", "qcom,ipq8064"; + + aliases { + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&gsbi4 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "okay"; + + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&pcie0 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie1 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie2 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&sata { + ports-implemented = <0x1>; +}; + +&smb208_s2a { + regulator-min-microvolt = <775000>; + regulator-max-microvolt = <1275000>; +}; + +&smb208_s2b { + regulator-min-microvolt = <775000>; + regulator-max-microvolt = <1275000>; +}; + +&ss_phy_0 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&ss_phy_1 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&opp_table_l2 { + /delete-node/opp-1200000000; + + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <1150000>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; +}; + +&opp_table0 { + /* + * On ipq8065 1.2 ghz freq is not present + * Remove it to make cpufreq work and not + * complain for missing definition + */ + + /delete-node/opp-1200000000; + + /* + * Voltage thresholds are <target min max> + */ + opp-384000000 { + opp-microvolt-speed0-pvs0-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs1-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; + opp-microvolt-speed0-pvs4-v0 = <875000 831250 918750>; + opp-microvolt-speed0-pvs5-v0 = <825000 783750 866250>; + opp-microvolt-speed0-pvs6-v0 = <775000 736250 813750>; + }; + + opp-600000000 { + opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs2-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs3-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs4-v0 = <900000 855000 945000>; + opp-microvolt-speed0-pvs5-v0 = <850000 807500 892500>; + opp-microvolt-speed0-pvs6-v0 = <800000 760000 840000>; + }; + + opp-800000000 { + opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs2-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs3-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs4-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs5-v0 = <900000 855000 945000>; + opp-microvolt-speed0-pvs6-v0 = <850000 807500 892500>; + }; + + opp-1000000000 { + opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs2-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs3-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs4-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs5-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs6-v0 = <900000 855000 945000>; + }; + + opp-1400000000 { + opp-microvolt-speed0-pvs0-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs1-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs3-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs4-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs5-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs6-v0 = <975000 926250 1023750>; + opp-level = <1>; + }; + + opp-1725000000 { + opp-hz = /bits/ 64 <1725000000>; + opp-microvolt-speed0-pvs0-v0 = <1262500 1199375 1325625>; + opp-microvolt-speed0-pvs1-v0 = <1225000 1163750 1286250>; + opp-microvolt-speed0-pvs2-v0 = <1200000 1140000 1260000>; + opp-microvolt-speed0-pvs3-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs4-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs5-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs6-v0 = <1050000 997500 1102500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; +};
Signature · 1 line
2.33.1
PATCH 17/17 ARM: dts: qcom: add ipq8065 dtsi
In reply to Ansuel SmithMany device are based on ipq8065 SoC. Ipq8065 is an evolution of the ipq8064 SoC (also named ipq8064-v3.0 from qsdk) that has all the improvement from ipq8064-v2.0 with the addition of a more powerful CPU that can now be clocked to 1.7Ghz, a quicker L2 cache that can be clocked to 1.4Ghz. It also shipped with more powerful regulators to provide the required voltage to the CPUs and L2.
--- arch/arm/boot/dts/qcom-ipq8065.dtsi | 168 ++++++++++++++++++++++++++++ 1 file changed, 168 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq8065.dtsi
arch/arm/boot/dts/qcom-ipq8065.dtsi new file +168 -0
@@ -0,0 +1,168 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "qcom-ipq8064.dtsi" + +/ { + model = "Qualcomm IPQ8065"; + compatible = "qcom,ipq8065", "qcom,ipq8064"; + + aliases { + serial0 = &gsbi4_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; +}; + +&gsbi4 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "okay"; + + serial@16340000 { + status = "okay"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ +}; + +&pcie0 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie1 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&pcie2 { + compatible = "qcom,pcie-ipq8064-v2"; +}; + +&sata { + ports-implemented = <0x1>; +}; + +&smb208_s2a { + regulator-min-microvolt = <775000>; + regulator-max-microvolt = <1275000>; +}; + +&smb208_s2b { + regulator-min-microvolt = <775000>; + regulator-max-microvolt = <1275000>; +}; + +&ss_phy_0 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&ss_phy_1 { + qcom,rx-eq = <2>; + qcom,tx-deamp_3_5db = <32>; + qcom,mpll = <5>; +}; + +&opp_table_l2 { + /delete-node/opp-1200000000; + + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <1150000>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; +}; + +&opp_table0 { + /* + * On ipq8065 1.2 ghz freq is not present + * Remove it to make cpufreq work and not + * complain for missing definition + */ + + /delete-node/opp-1200000000; + + /* + * Voltage thresholds are <target min max> + */ + opp-384000000 { + opp-microvolt-speed0-pvs0-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs1-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs2-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs3-v0 = <900000 855000 945000>; + opp-microvolt-speed0-pvs4-v0 = <875000 831250 918750>; + opp-microvolt-speed0-pvs5-v0 = <825000 783750 866250>; + opp-microvolt-speed0-pvs6-v0 = <775000 736250 813750>; + }; + + opp-600000000 { + opp-microvolt-speed0-pvs0-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs1-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs2-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs3-v0 = <925000 878750 971250>; + opp-microvolt-speed0-pvs4-v0 = <900000 855000 945000>; + opp-microvolt-speed0-pvs5-v0 = <850000 807500 892500>; + opp-microvolt-speed0-pvs6-v0 = <800000 760000 840000>; + }; + + opp-800000000 { + opp-microvolt-speed0-pvs0-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs1-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs2-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs3-v0 = <975000 926250 1023750>; + opp-microvolt-speed0-pvs4-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs5-v0 = <900000 855000 945000>; + opp-microvolt-speed0-pvs6-v0 = <850000 807500 892500>; + }; + + opp-1000000000 { + opp-microvolt-speed0-pvs0-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs1-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs2-v0 = <1050000 997500 1102500>; + opp-microvolt-speed0-pvs3-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs4-v0 = <1000000 950000 1050000>; + opp-microvolt-speed0-pvs5-v0 = <950000 902500 997500>; + opp-microvolt-speed0-pvs6-v0 = <900000 855000 945000>; + }; + + opp-1400000000 { + opp-microvolt-speed0-pvs0-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs1-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs2-v0 = <1125000 1068750 1181250>; + opp-microvolt-speed0-pvs3-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs4-v0 = <1075000 1021250 1128750>; + opp-microvolt-speed0-pvs5-v0 = <1025000 973750 1076250>; + opp-microvolt-speed0-pvs6-v0 = <975000 926250 1023750>; + opp-level = <1>; + }; + + opp-1725000000 { + opp-hz = /bits/ 64 <1725000000>; + opp-microvolt-speed0-pvs0-v0 = <1262500 1199375 1325625>; + opp-microvolt-speed0-pvs1-v0 = <1225000 1163750 1286250>; + opp-microvolt-speed0-pvs2-v0 = <1200000 1140000 1260000>; + opp-microvolt-speed0-pvs3-v0 = <1175000 1116250 1233750>; + opp-microvolt-speed0-pvs4-v0 = <1150000 1092500 1207500>; + opp-microvolt-speed0-pvs5-v0 = <1100000 1045000 1155000>; + opp-microvolt-speed0-pvs6-v0 = <1050000 997500 1102500>; + opp-supported-hw = <0x1>; + clock-latency-ns = <100000>; + opp-level = <2>; + }; +};
Signature · 1 line
2.33.1
Quoted 14 lines · Ansuel Smith
This try to complete the ipq8064 dtsi and introduce 2 new dtsi ipq8064-v2 and ipq8065. While some node are still missing (cpufreq node, l2 scale node, fab scale node) this would add most of the missing node to make ipq8064 actually usable.
Some of the changes are the fix for the pci IO that cause any secondary wifi card with ath10k to fail init.
Adds regulators definition for RPM.
Adds many missing gsbi nodes used by all the devices.
Enable the usb phy by default as they are actually enabled internally by xlate only if the dwc3 driver is used.
Add opp table and declare idle state for ipq8064.
Fix some dtc warning.
Quoted 3 lines
This also add the ipq8064-v2.0 dtsi and the ipq8065 dtsi used by more recent devices based on this SoC.
From the look of the series I suspect that you format-patch'ed a series with 16 patches, then fixed something and re-ran it now with 17 patches.
Can you please resubmit the series to make it clear what you would like me to apply. (Preferably with that one commit message clarified)
Regards,
Bjorn
Quoted 31 lines
Ansuel Smith (17):
ARM: dts: qcom: add multiple missing pin definition for ipq8064
ARM: dts: qcom: add gsbi6 missing definition for ipq8064
ARM: dts: qcom: add missing rpm regulators and cells for ipq8064
ARM: dts: qcom: add missing snps,dwmac compatible for gmac ipq8064
ARM: dts: qcom: enable usb phy by default for ipq8064
ARM: dts: qcom: reduce pci IO size to 64K for ipq8064
ARM: dts: qcom: fix dtc warning for missing #address-cells for ipq8064
ARM: dts: qcom: add smem node for ipq8064
ARM: dts: qcom: add saw for l2 cache and kraitcc for ipq8064
ARM: dts: qcom: add sic non secure node for ipq8064
ARM: dts: qcom: fix and add some missing gsbi node for ipq8064
ARM: dts: qcom: add opp table for cpu and l2 for ipq8064
ARM: dts: qcom: add speedbin efuse nvmem binding
ARM: dts: qcom: add multiple missing binding for cpu and l2 foripq8064ARM: dts: qcom: remove redundant binding from ipq8064 rb3011 dts
ARM: dts: qcom: add ipq8064-v2.0 dtsi
ARM: dts: qcom: add ipq8065 dtsiarch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 17 -- arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi | 70 +++++ arch/arm/boot/dts/qcom-ipq8064.dtsi | 344 +++++++++++++++++++++- arch/arm/boot/dts/qcom-ipq8065.dtsi | 168 +++++++++++ 4 files changed, 568 insertions(+), 31 deletions(-) create mode 100644 arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi create mode 100644 arch/arm/boot/dts/qcom-ipq8065.dtsiSignature · 1 line
2.33.1