arm: kirkwood: Dreamplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
PATCH 1/1 arm: kirkwood: Dreamplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
The Globalscale Technologies Dreamplug board has the network chip Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310 driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood boards with mv8831116 PHY, with each board defines the function reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned, could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file board/Marvell/dreamplug/dreamplug.h, cleanup comments.
---
board/Marvell/dreamplug/MAINTAINERS | 1 + board/Marvell/dreamplug/dreamplug.c | 94 +++++------------------------ board/Marvell/dreamplug/dreamplug.h | 25 -------- configs/dreamplug_defconfig | 1 + include/configs/dreamplug.h | 20 ++---- 5 files changed, 21 insertions(+), 120 deletions(-) delete mode 100644 board/Marvell/dreamplug/dreamplug.h
board/Marvell/dreamplug/MAINTAINERS +1 -0
@@ -1,4 +1,5 @@ DREAMPLUG BOARD +M: Tony Dinh <[email protected]> M: Jason Cooper <[email protected]> S: Maintained F: board/Marvell/dreamplug/
board/Marvell/dreamplug/dreamplug.c +14 -80
121 lines not on this page · raw message
board/Marvell/dreamplug/dreamplug.h deleted +0 -25
@@ -1,25 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> -* -* Based on work by: -* Marvell Semiconductor <www.marvell.com> -* Written-by: Siddarth Gore <[email protected]> -*/ - -#ifndef __DREAMPLUG_H -#define __DREAMPLUG_H - -#define DREAMPLUG_OE_LOW (~(0)) -#define DREAMPLUG_OE_HIGH (~(0)) -#define DREAMPLUG_OE_VAL_LOW 0 -#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ - -/* PHY related */ -#define MV88E1116_MAC_CTRL2_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __DREAMPLUG_H */
configs/dreamplug_defconfig +1 -0
@@ -45,6 +45,7 @@ CONFIG_SATA_MV=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_PHY_MARVELL=y CONFIG_DM_ETH=y CONFIG_MVGBE=y CONFIG_MII=y
include/configs/dreamplug.h +5 -15
@@ -1,7 +1,7 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* (C) Copyright 2022 Tony Dinh <[email protected]> +* (C) Copyright 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com>
@@ -13,15 +13,6 @@#include "mv-common.h" -/* -* Environment variables configurations -*/ - -/* -* max 4k env size is enough, but in case of nand -* it has to be rounded to sector size -*/ -/* * Default environment variables */
@@ -36,17 +27,16 @@/* * Ethernet Driver configuration */ -#ifdef CONFIG_CMD_NET #define CONFIG_MVGBE_PORTS {1, 1}/* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#endif /* CONFIG_CMD_NET */ +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R/* remove legacy reset_phy() */ +#endif /* * SATA Driver configuration */ -#ifdef CONFIG_SATA #define CONFIG_SYS_SATA_MAX_DEVICE 1#define CONFIG_LBA48 -#endif /* CONFIG_SATA */ #endif /* _CONFIG_DREAMPLUG_H */
Signature · 1 line
2.30.2
Quoted 16 lines · Tony Dinh
The Globalscale Technologies Dreamplug board has the network chip Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310 driver to bring up Ethernet.
- Currently,
CONFIG_RESET_PHY_Rsymbol is used inarch/arm/mach-kirkwood/include/mach/config.hfor all Kirkwood boards with mv8831116 PHY, with each board defines the functionreset_phy(). Undefine it for this board.
- Addboard_eth_init()to use uclass mvgbe to bring up both network port 0 and 1. And remove ad-hoc code.
- EnableCONFIG_PHY_MARVELLto properly configure the network.
- Add myself as maintainer (this board seems to be orphaned, could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header fileboard/Marvell/dreamplug/dreamplug.h, cleanup comments.
Quoted 1 line
Signed-off-by Tony Dinh <[email protected]>
Thanks,
Stefan
Quoted 232 lines
---
board/Marvell/dreamplug/MAINTAINERS | 1 + board/Marvell/dreamplug/dreamplug.c | 94 +++++------------------------ board/Marvell/dreamplug/dreamplug.h | 25 -------- configs/dreamplug_defconfig | 1 + include/configs/dreamplug.h | 20 ++---- 5 files changed, 21 insertions(+), 120 deletions(-)delete mode 100644
board/Marvell/dreamplug/dreamplug.hboard/Marvell/dreamplug/MAINTAINERS +1
-0@@ -1,4 +1,5 @@ DREAMPLUG BOARD +M: Tony Dinh <[email protected]> M: Jason Cooper <[email protected]> S: Maintained F: board/Marvell/dreamplug/board/Marvell/dreamplug/dreamplug.c +14
-80@@ -1,8 +1,7 @@// SPDX-License-Identifier: GPL-2.0+ /* -* Copyright (C) 2021 Tony Dinh <[email protected]> -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* Copyright (C) 2021-2022 Tony Dinh <[email protected]> +* Copyright (C) 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com> @@ -11,16 +10,19 @@#include <common.h> #include <init.h> -#include <miiphy.h> -#include <net.h> +#include <netdev.h> #include <asm/arch/cpu.h> #include <asm/arch/soc.h> #include <asm/arch/mpp.h> #include <asm/global_data.h> -#include "dreamplug.h" DECLARE_GLOBAL_DATA_PTR ; +#define DREAMPLUG_OE_LOW (~(0)) +#define DREAMPLUG_OE_HIGH (~(0)) +#define DREAMPLUG_OE_VAL_LOW 0 +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ +int board_early_init_f (void ) {/* @@ -90,83 +92,15 @@ int board_early_init_f(void)return 0 ; } -int board_init (void ) -{ -/* adress of boot parameters */ - gd->bd->bi_boot_params =mvebu_sdram_bar (0 ) +0x100 ; - -return 0 ; -} - -static int fdt_get_phy_addr (const char *path) -{ -const void *fdt = gd->fdt_blob; -const u32 *reg; -const u32 *val; -int node, phandle, addr; - -/* Find the node by its full path */ - node =fdt_path_offset (fdt, path); -if (node >=0 ) { -/* Look up phy-handle */ - val =fdt_getprop (fdt, node,"phy-handle" ,NULL ); -if (val) { - phandle =fdt32_to_cpu (*val); -if (!phandle) -return -1 ; -/* Follow it to its node */ - node =fdt_node_offset_by_phandle (fdt, phandle); -if (node) { -/* Look up reg */ - reg =fdt_getprop (fdt, node,"reg" ,NULL ); -if (reg) { - addr =fdt32_to_cpu (*reg); -return addr; - } - } - } - } -return -1 ; -} - -#ifdef CONFIG_RESET_PHY_R -void mv_phy_88e1116_init (const char *name,const char *path) +int board_eth_init (struct bd_info *bis) { -u16 reg; -int phyaddr; - -if (miiphy_set_current_dev (name)) -return ; - - phyaddr =fdt_get_phy_addr (path); -if (phyaddr <0 ) -return ; - -/* -* Enable RGMII delay on Tx and Rx for CPU port -* Ref: sec 4.7.2 of chip datasheet -*/ -miiphy_write (name, phyaddr,MV88E1116_PGADR_REG ,2 ); -miiphy_read (name, phyaddr,MV88E1116_MAC_CTRL2_REG , ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL |MV88E1116_RGMII_TXTM_CTRL ); -miiphy_write (name, phyaddr,MV88E1116_MAC_CTRL2_REG , reg); -miiphy_write (name, phyaddr,MV88E1116_PGADR_REG ,0 ); - -/* reset the phy */ -miiphy_reset (name, phyaddr); - -printf ("88E1116 Initialized on %s\n" , name); +return cpu_eth_init (bis); } -void reset_phy (void ) +int board_init (void ) { -char *eth0_name ="ethernet-controller@72000" ; -char *eth0_path ="/ocp@f1000000/ethernet-controller@72000/ethernet0-port@0" ; -char *eth1_name ="ethernet-controller@76000" ; -char *eth1_path ="/ocp@f1000000/ethernet-controller@76000/ethernet1-port@0" ; +/* address of boot parameters */ + gd->bd->bi_boot_params =mvebu_sdram_bar (0 ) +0x100 ; -/* configure and initialize both PHY's */ -mv_phy_88e1116_init (eth0_name, eth0_path); -mv_phy_88e1116_init (eth1_name, eth1_path); +return 0 ; } -#endif /* CONFIG_RESET_PHY_R */ board/Marvell/dreamplug/dreamplug.h deleted +0
-25@@ -1,25 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> -* -* Based on work by: -* Marvell Semiconductor <www.marvell.com> -* Written-by: Siddarth Gore <[email protected]> -*/ - -#ifndef __DREAMPLUG_H -#define __DREAMPLUG_H - -#define DREAMPLUG_OE_LOW (~(0)) -#define DREAMPLUG_OE_HIGH (~(0)) -#define DREAMPLUG_OE_VAL_LOW 0 -#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ - -/* PHY related */ -#define MV88E1116_MAC_CTRL2_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __DREAMPLUG_H */ configs/dreamplug_defconfig +1
-0@@ -45,6 +45,7 @@ CONFIG_SATA_MV=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_PHY_MARVELL=y CONFIG_DM_ETH=y CONFIG_MVGBE=y CONFIG_MII=yinclude/configs/dreamplug.h +5
-13@@ -1,7 +1,7 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* (C) Copyright 2022 Tony Dinh <[email protected]> +* (C) Copyright 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com> @@ -13,15 +13,6 @@#include "mv-common.h" -/* -* Environment variables configurations -*/ - -/* -* max 4k env size is enough, but in case of nand -* it has to be rounded to sector size -*/ -/* * Default environment variables */ @@ -36,17 +27,16 @@/* * Ethernet Driver configuration */ -#ifdef CONFIG_CMD_NET #define CONFIG_MVGBE_PORTS {1, 1}/* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#endif /* CONFIG_CMD_NET */ +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R/* remove legacy reset_phy() */ +#endif
include/configs/dreamplug.h line 42
Quoted 10 lines
include/configs/dreamplug.h +0
-2/* * SATA Driver configuration */ -#ifdef CONFIG_SATA #define CONFIG_SYS_SATA_MAX_DEVICE 1#define CONFIG_LBA48 -#endif /* CONFIG_SATA */ #endif /* _CONFIG_DREAMPLUG_H */
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
Quoted 16 lines · On Sunday 30 January 2022 15:02:30 Tony Dinh wrote:
The Globalscale Technologies Dreamplug board has the network chip Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310 driver to bring up Ethernet.
- Currently,
CONFIG_RESET_PHY_Rsymbol is used inarch/arm/mach-kirkwood/include/mach/config.hfor all Kirkwood boards with mv8831116 PHY, with each board defines the functionreset_phy(). Undefine it for this board.
- Addboard_eth_init()to use uclass mvgbe to bring up both network port 0 and 1. And remove ad-hoc code.
- EnableCONFIG_PHY_MARVELLto properly configure the network.
- Add myself as maintainer (this board seems to be orphaned, could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header fileboard/Marvell/dreamplug/dreamplug.h, cleanup comments.
Quoted 1 line
Signed-off-by Tony Dinh <[email protected]>
Quoted 245 lines
---
board/Marvell/dreamplug/MAINTAINERS | 1 + board/Marvell/dreamplug/dreamplug.c | 94 +++++------------------------ board/Marvell/dreamplug/dreamplug.h | 25 -------- configs/dreamplug_defconfig | 1 + include/configs/dreamplug.h | 20 ++---- 5 files changed, 21 insertions(+), 120 deletions(-) delete mode 100644 board/Marvell/dreamplug/dreamplug.hboard/Marvell/dreamplug/MAINTAINERS +1
-0@@ -1,4 +1,5 @@ DREAMPLUG BOARD +M: Tony Dinh <[email protected]> M: Jason Cooper <[email protected]> S: Maintained F: board/Marvell/dreamplug/board/Marvell/dreamplug/dreamplug.c +14
-80@@ -1,8 +1,7 @@// SPDX-License-Identifier: GPL-2.0+ /* -* Copyright (C) 2021 Tony Dinh <[email protected]> -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* Copyright (C) 2021-2022 Tony Dinh <[email protected]> +* Copyright (C) 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com> @@ -11,16 +10,19 @@#include <common.h> #include <init.h> -#include <miiphy.h> -#include <net.h> +#include <netdev.h> #include <asm/arch/cpu.h> #include <asm/arch/soc.h> #include <asm/arch/mpp.h> #include <asm/global_data.h> -#include "dreamplug.h" DECLARE_GLOBAL_DATA_PTR ; +#define DREAMPLUG_OE_LOW (~(0)) +#define DREAMPLUG_OE_HIGH (~(0)) +#define DREAMPLUG_OE_VAL_LOW 0 +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ +int board_early_init_f (void ) {/* @@ -90,83 +92,15 @@ int board_early_init_f(void)return 0 ; } -int board_init (void ) -{ -/* adress of boot parameters */ - gd->bd->bi_boot_params =mvebu_sdram_bar (0 ) +0x100 ; - -return 0 ; -} - -static int fdt_get_phy_addr (const char *path) -{ -const void *fdt = gd->fdt_blob; -const u32 *reg; -const u32 *val; -int node, phandle, addr; - -/* Find the node by its full path */ - node =fdt_path_offset (fdt, path); -if (node >=0 ) { -/* Look up phy-handle */ - val =fdt_getprop (fdt, node,"phy-handle" ,NULL ); -if (val) { - phandle =fdt32_to_cpu (*val); -if (!phandle) -return -1 ; -/* Follow it to its node */ - node =fdt_node_offset_by_phandle (fdt, phandle); -if (node) { -/* Look up reg */ - reg =fdt_getprop (fdt, node,"reg" ,NULL ); -if (reg) { - addr =fdt32_to_cpu (*reg); -return addr; - } - } - } - } -return -1 ; -} - -#ifdef CONFIG_RESET_PHY_R -void mv_phy_88e1116_init (const char *name,const char *path) +int board_eth_init (struct bd_info *bis) { -u16 reg; -int phyaddr; - -if (miiphy_set_current_dev (name)) -return ; - - phyaddr =fdt_get_phy_addr (path); -if (phyaddr <0 ) -return ; - -/* -* Enable RGMII delay on Tx and Rx for CPU port -* Ref: sec 4.7.2 of chip datasheet -*/ -miiphy_write (name, phyaddr,MV88E1116_PGADR_REG ,2 ); -miiphy_read (name, phyaddr,MV88E1116_MAC_CTRL2_REG , ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL |MV88E1116_RGMII_TXTM_CTRL ); -miiphy_write (name, phyaddr,MV88E1116_MAC_CTRL2_REG , reg); -miiphy_write (name, phyaddr,MV88E1116_PGADR_REG ,0 ); - -/* reset the phy */ -miiphy_reset (name, phyaddr); - -printf ("88E1116 Initialized on %s\n" , name); +return cpu_eth_init (bis); } -void reset_phy (void ) +int board_init (void ) { -char *eth0_name ="ethernet-controller@72000" ; -char *eth0_path ="/ocp@f1000000/ethernet-controller@72000/ethernet0-port@0" ; -char *eth1_name ="ethernet-controller@76000" ; -char *eth1_path ="/ocp@f1000000/ethernet-controller@76000/ethernet1-port@0" ; +/* address of boot parameters */ + gd->bd->bi_boot_params =mvebu_sdram_bar (0 ) +0x100 ; -/* configure and initialize both PHY's */ -mv_phy_88e1116_init (eth0_name, eth0_path); -mv_phy_88e1116_init (eth1_name, eth1_path); +return 0 ; } -#endif /* CONFIG_RESET_PHY_R */ board/Marvell/dreamplug/dreamplug.h deleted +0
-25@@ -1,25 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> -* -* Based on work by: -* Marvell Semiconductor <www.marvell.com> -* Written-by: Siddarth Gore <[email protected]> -*/ - -#ifndef __DREAMPLUG_H -#define __DREAMPLUG_H - -#define DREAMPLUG_OE_LOW (~(0)) -#define DREAMPLUG_OE_HIGH (~(0)) -#define DREAMPLUG_OE_VAL_LOW 0 -#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ - -/* PHY related */ -#define MV88E1116_MAC_CTRL2_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __DREAMPLUG_H */ configs/dreamplug_defconfig +1
-0@@ -45,6 +45,7 @@ CONFIG_SATA_MV=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_PHY_MARVELL=y CONFIG_DM_ETH=y CONFIG_MVGBE=y CONFIG_MII=yinclude/configs/dreamplug.h +5
-15@@ -1,7 +1,7 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* (C) Copyright 2022 Tony Dinh <[email protected]> +* (C) Copyright 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com> @@ -13,15 +13,6 @@#include "mv-common.h" -/* -* Environment variables configurations -*/ - -/* -* max 4k env size is enough, but in case of nand -* it has to be rounded to sector size -*/ -/* * Default environment variables */ @@ -36,17 +27,16 @@/* * Ethernet Driver configuration */ -#ifdef CONFIG_CMD_NET #define CONFIG_MVGBE_PORTS {1, 1}/* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#endif /* CONFIG_CMD_NET */ +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R/* remove legacy reset_phy() */ +#endif /* * SATA Driver configuration */ -#ifdef CONFIG_SATA #define CONFIG_SYS_SATA_MAX_DEVICE 1#define CONFIG_LBA48 -#endif /* CONFIG_SATA */ #endif /* _CONFIG_DREAMPLUG_H */ Signature · 1 line
2.30.2
Quoted 16 lines · Tony Dinh
The Globalscale Technologies Dreamplug board has the network chip Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310 driver to bring up Ethernet.
- Currently,
CONFIG_RESET_PHY_Rsymbol is used inarch/arm/mach-kirkwood/include/mach/config.hfor all Kirkwood boards with mv8831116 PHY, with each board defines the functionreset_phy(). Undefine it for this board.
- Addboard_eth_init()to use uclass mvgbe to bring up both network port 0 and 1. And remove ad-hoc code.
- EnableCONFIG_PHY_MARVELLto properly configure the network.
- Add myself as maintainer (this board seems to be orphaned, could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header fileboard/Marvell/dreamplug/dreamplug.h, cleanup comments.
Quoted 1 line
Signed-off-by Tony Dinh <[email protected]>
Applied to u-boot-marvell/master
Thanks,
Stefan
Quoted 232 lines
---
board/Marvell/dreamplug/MAINTAINERS | 1 + board/Marvell/dreamplug/dreamplug.c | 94 +++++------------------------ board/Marvell/dreamplug/dreamplug.h | 25 -------- configs/dreamplug_defconfig | 1 + include/configs/dreamplug.h | 20 ++---- 5 files changed, 21 insertions(+), 120 deletions(-)delete mode 100644
board/Marvell/dreamplug/dreamplug.hboard/Marvell/dreamplug/MAINTAINERS +1
-0@@ -1,4 +1,5 @@ DREAMPLUG BOARD +M: Tony Dinh <[email protected]> M: Jason Cooper <[email protected]> S: Maintained F: board/Marvell/dreamplug/board/Marvell/dreamplug/dreamplug.c +14
-80@@ -1,8 +1,7 @@// SPDX-License-Identifier: GPL-2.0+ /* -* Copyright (C) 2021 Tony Dinh <[email protected]> -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* Copyright (C) 2021-2022 Tony Dinh <[email protected]> +* Copyright (C) 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com> @@ -11,16 +10,19 @@#include <common.h> #include <init.h> -#include <miiphy.h> -#include <net.h> +#include <netdev.h> #include <asm/arch/cpu.h> #include <asm/arch/soc.h> #include <asm/arch/mpp.h> #include <asm/global_data.h> -#include "dreamplug.h" DECLARE_GLOBAL_DATA_PTR ; +#define DREAMPLUG_OE_LOW (~(0)) +#define DREAMPLUG_OE_HIGH (~(0)) +#define DREAMPLUG_OE_VAL_LOW 0 +#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ +int board_early_init_f (void ) {/* @@ -90,83 +92,15 @@ int board_early_init_f(void)return 0 ; } -int board_init (void ) -{ -/* adress of boot parameters */ - gd->bd->bi_boot_params =mvebu_sdram_bar (0 ) +0x100 ; - -return 0 ; -} - -static int fdt_get_phy_addr (const char *path) -{ -const void *fdt = gd->fdt_blob; -const u32 *reg; -const u32 *val; -int node, phandle, addr; - -/* Find the node by its full path */ - node =fdt_path_offset (fdt, path); -if (node >=0 ) { -/* Look up phy-handle */ - val =fdt_getprop (fdt, node,"phy-handle" ,NULL ); -if (val) { - phandle =fdt32_to_cpu (*val); -if (!phandle) -return -1 ; -/* Follow it to its node */ - node =fdt_node_offset_by_phandle (fdt, phandle); -if (node) { -/* Look up reg */ - reg =fdt_getprop (fdt, node,"reg" ,NULL ); -if (reg) { - addr =fdt32_to_cpu (*reg); -return addr; - } - } - } - } -return -1 ; -} - -#ifdef CONFIG_RESET_PHY_R -void mv_phy_88e1116_init (const char *name,const char *path) +int board_eth_init (struct bd_info *bis) { -u16 reg; -int phyaddr; - -if (miiphy_set_current_dev (name)) -return ; - - phyaddr =fdt_get_phy_addr (path); -if (phyaddr <0 ) -return ; - -/* -* Enable RGMII delay on Tx and Rx for CPU port -* Ref: sec 4.7.2 of chip datasheet -*/ -miiphy_write (name, phyaddr,MV88E1116_PGADR_REG ,2 ); -miiphy_read (name, phyaddr,MV88E1116_MAC_CTRL2_REG , ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL |MV88E1116_RGMII_TXTM_CTRL ); -miiphy_write (name, phyaddr,MV88E1116_MAC_CTRL2_REG , reg); -miiphy_write (name, phyaddr,MV88E1116_PGADR_REG ,0 ); - -/* reset the phy */ -miiphy_reset (name, phyaddr); - -printf ("88E1116 Initialized on %s\n" , name); +return cpu_eth_init (bis); } -void reset_phy (void ) +int board_init (void ) { -char *eth0_name ="ethernet-controller@72000" ; -char *eth0_path ="/ocp@f1000000/ethernet-controller@72000/ethernet0-port@0" ; -char *eth1_name ="ethernet-controller@76000" ; -char *eth1_path ="/ocp@f1000000/ethernet-controller@76000/ethernet1-port@0" ; +/* address of boot parameters */ + gd->bd->bi_boot_params =mvebu_sdram_bar (0 ) +0x100 ; -/* configure and initialize both PHY's */ -mv_phy_88e1116_init (eth0_name, eth0_path); -mv_phy_88e1116_init (eth1_name, eth1_path); +return 0 ; } -#endif /* CONFIG_RESET_PHY_R */ board/Marvell/dreamplug/dreamplug.h deleted +0
-25@@ -1,25 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> -* -* Based on work by: -* Marvell Semiconductor <www.marvell.com> -* Written-by: Siddarth Gore <[email protected]> -*/ - -#ifndef __DREAMPLUG_H -#define __DREAMPLUG_H - -#define DREAMPLUG_OE_LOW (~(0)) -#define DREAMPLUG_OE_HIGH (~(0)) -#define DREAMPLUG_OE_VAL_LOW 0 -#define DREAMPLUG_OE_VAL_HIGH (0xf << 16)/* 4 LED Pins high */ - -/* PHY related */ -#define MV88E1116_MAC_CTRL2_REG 21 -#define MV88E1116_PGADR_REG 22 -#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) -#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) - -#endif /* __DREAMPLUG_H */ configs/dreamplug_defconfig +1
-0@@ -45,6 +45,7 @@ CONFIG_SATA_MV=y CONFIG_MTD=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_PHY_MARVELL=y CONFIG_DM_ETH=y CONFIG_MVGBE=y CONFIG_MII=yinclude/configs/dreamplug.h +5
-13@@ -1,7 +1,7 @@/* SPDX-License-Identifier: GPL-2.0+ */ /* -* (C) Copyright 2011 -* Jason Cooper <[email protected]> +* (C) Copyright 2022 Tony Dinh <[email protected]> +* (C) Copyright 2011 Jason Cooper <[email protected]> * * Based on work by: * Marvell Semiconductor <www.marvell.com> @@ -13,15 +13,6 @@#include "mv-common.h" -/* -* Environment variables configurations -*/ - -/* -* max 4k env size is enough, but in case of nand -* it has to be rounded to sector size -*/ -/* * Default environment variables */ @@ -36,17 +27,16 @@/* * Ethernet Driver configuration */ -#ifdef CONFIG_CMD_NET #define CONFIG_MVGBE_PORTS {1, 1}/* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#endif /* CONFIG_CMD_NET */ +#ifdef CONFIG_RESET_PHY_R +#undef CONFIG_RESET_PHY_R/* remove legacy reset_phy() */ +#endif
include/configs/dreamplug.h line 42
Quoted 10 lines
include/configs/dreamplug.h +0
-2/* * SATA Driver configuration */ -#ifdef CONFIG_SATA #define CONFIG_SYS_SATA_MAX_DEVICE 1#define CONFIG_LBA48 -#endif /* CONFIG_SATA */ #endif /* _CONFIG_DREAMPLUG_H */
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]