Skip to contentSkip to conversation

WIP: Nokia RX-51: Convert to CONFIG_DM_VIDEO

PATCH In review Pali Rohár 3 participants 22 messages Feb 16, 2022 – Mar 14, 2022 Framebuffer layer

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 WIP: Nokia RX-51: Convert to CONFIG_DM_VIDEO

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Othwise framebuffer works.

---
 board/nokia/rx51/rx51.c      | 41 ++++++++++++++++++++++--------------
 configs/nokia_rx51_defconfig |  7 ++++--
 drivers/video/video-uclass.c |  4 +++-
 include/configs/nokia_rx51.h | 11 ++--------
 4 files changed, 35 insertions(+), 28 deletions(-)
board/nokia/rx51/rx51.c +25 -16
index a52691509da4..e2fe411b34be 100644
@@ -30,7 +30,7 @@
 #include <malloc.h>
 #include <twl4030.h>
 #include <i2c.h>
-#include <video_fb.h>
+#include <video.h>
 #include <keyboard.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
@@ -62,8 +62,6 @@ struct emu_hal_params_rx51 {
 
 DECLARE_GLOBAL_DATA_PTR;
 
-GraphicDevice gdev;
-
 const omap3_sysinfo sysinfo = {
 	DDR_STACKED,
 	"Nokia RX-51",
@@ -342,22 +340,29 @@ void setup_board_tags(struct tag **in_params)
 	*in_params = params;
 }
 
-/*
- * Routine: video_hw_init
- * Description: Set up the GraphicDevice depending on sys_boot.
- */
-void *video_hw_init(void)
+static int rx51_video_probe(struct udevice *dev)
 {
-	/* fill in Graphic Device */
-	gdev.frameAdrs = 0x8f9c0000;
-	gdev.winSizeX = 800;
-	gdev.winSizeY = 480;
-	gdev.gdfBytesPP = 2;
-	gdev.gdfIndex = GDF_16BIT_565RGB;
-	memset((void *)gdev.frameAdrs, 0, 0xbb800);
-	return (void *) &gdev;
+	struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+	struct video_priv *uc_priv = dev_get_uclass_priv(dev);
+
+	uc_plat->base = 0x8f9c0000;
+	uc_plat->size = 800 * 480 * sizeof(u16);
+	uc_priv->xsize = 800;
+	uc_priv->ysize = 480;
+	uc_priv->bpix = VIDEO_BPP16;
+
+	video_set_flush_dcache(dev, true);
+
+	return 0;
 }
 
+U_BOOT_DRIVER(rx51_video) = {
+	.name = "rx51_video",
+	.id = UCLASS_VIDEO,
+	.probe = rx51_video_probe,
+	.flags = DM_FLAG_PRE_RELOC,
+};
+
 /*
  * Routine: twl4030_regulator_set_mode
  * Description: Set twl4030 regulator mode over i2c powerbus.
@@ -777,6 +782,10 @@ U_BOOT_DRVINFOS(rx51_watchdog) = {
 	{ "rx51_watchdog" },
 };
 
+U_BOOT_DRVINFOS(rx51_video) = {
+	{ "rx51_video" },
+};
+
 U_BOOT_DRVINFOS(rx51_kp) = {
 	{ "rx51_kp" },
 };
configs/nokia_rx51_defconfig +5 -2
index 47b7bc3b4f03..1d64981afc46 100644
@@ -77,8 +77,11 @@ CONFIG_SPI=y
 CONFIG_USB=y
 CONFIG_USB_MUSB_UDC=y
 CONFIG_USB_OMAP3=y
-CONFIG_CFB_CONSOLE=y
-CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_LOGO=y
+# CONFIG_VIDEO_BPP8 is not set
+# CONFIG_VIDEO_BPP32 is not set
+CONFIG_SYS_WHITE_ON_BLACK=y
 CONFIG_SPLASH_SCREEN=y
 CONFIG_WATCHDOG_TIMEOUT_MSECS=31000
 CONFIG_WDT=y
drivers/video/video-uclass.c +3 -1
index 7d499bcec51d..98cc5c0b17da 100644
@@ -3,6 +3,8 @@
  * Copyright (c) 2015 Google, Inc
  */
 
+#define DEBUG
+
 #define LOG_CATEGORY UCLASS_VIDEO
 
 #include <common.h>
@@ -438,7 +440,7 @@ static int video_post_bind(struct udevice *dev)
 		 */
 		printf("Video device '%s' cannot allocate frame buffer memory -ensure the device is set up before relocation\n",
 		       dev->name);
-		return -ENOSPC;
+//		return -ENOSPC;
 	}
 	debug("%s: Claiming %lx bytes at %lx for video device '%s'\n",
 	      __func__, size, addr, dev->name);
include/configs/nokia_rx51.h +2 -9
index 9be64c3d3f87..e837b12b568f 100644
@@ -70,19 +70,12 @@
 
 #define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
 
-/*
- * Framebuffer
- */
-/* Video console */
-#define VIDEO_FB_16BPP_PIXEL_SWAP
-#define VIDEO_FB_16BPP_WORD_SWAP
-
 /* Environment information */
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"usbtty=cdc_acm\0" \
 	"stdin=usbtty,serial,keyboard\0" \
-	"stdout=usbtty,serial,vga\0" \
-	"stderr=usbtty,serial,vga\0" \
+	"stdout=usbtty,serial,vidconsole\0" \
+	"stderr=usbtty,serial,vidconsole\0" \
 	"slide=gpio input " __stringify(GPIO_SLIDE) "\0" \
 	"switchmmc=mmc dev ${mmcnum}\0" \
 	"kernaddr=0x82008000\0" \
Signature · 1 line
2.20.1
#1 lore raw

Hi Pali,

Quoted 5 lines · On Wed, 16 Feb 2022 21:42:19 +0100 Pali Rohár [email protected] wrote:

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Probably the frame buffer memory allocation did not work. Could you please try with a bind callback, i.e.:

static int rx51_video_bind(struct udevice *dev)

{
	struct video_uc_plat *plat = dev_get_uclass_plat(dev);

	plat->size = 800 * 480 * 2;
	return 0;
}
...
U_BOOT_DRIVER(rx51_video) = {
	.name = "rx51_video",
	.id = UCLASS_VIDEO,
	.bind = rx51_video_bind,
	.probe = rx51_video_probe,
	.flags = DM_FLAG_PRE_RELOC,
};
Quoted 5 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

--
Anatolij

#2 lore raw
Quoted 15 lines · On Thursday 17 February 2022 09:53:39 Anatolij Gustschin wrote:

Hi Pali,

Quoted 5 lines · On Wed, 16 Feb 2022 21:42:19 +0100 Pali Rohár [email protected] wrote:

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Probably the frame buffer memory allocation did not work. Could you please try with a bind callback, i.e.:

static int rx51_video_bind(struct udevice *dev)

Quoted 14 lines
{
	struct video_uc_plat *plat = dev_get_uclass_plat(dev);

	plat->size = 800 * 480 * 2;
	return 0;
}
...
U_BOOT_DRIVER(rx51_video) = {
	.name = "rx51_video",
	.id = UCLASS_VIDEO,
	.bind = rx51_video_bind,
	.probe = rx51_video_probe,
	.flags = DM_FLAG_PRE_RELOC,
};

Hello! It does not work too. Here is the output:

U-Boot 2022.04-rc2-00002-ga2c1a9878375-dirty (Jan 01 1970 - 00:00:00 +0000)

OMAP35XX-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz
DRAM: Video frame buffers from 8fe30000 to 8fe30000
256 MiB
Video device 'rx51_video' cannot allocate frame buffer memory -ensure the device is set up before relocation

If "return -ENOSPC;" is not commented then this is the last printed line. If it is commented then output continues with:

video_post_bind: Claiming 130000 bytes at 8fd00000 for video device 'rx51_video'

And framebuffer is working fine like without above rx51_video_bind() change.

Quoted 12 lines
Quoted 5 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

--
Anatolij

#3 lore raw

PING?

Quoted 60 lines · On Thursday 17 February 2022 13:20:43 Pali Rohár wrote:
Quoted 15 lines · On Thursday 17 February 2022 09:53:39 Anatolij Gustschin wrote:

Hi Pali,

Quoted 5 lines · On Wed, 16 Feb 2022 21:42:19 +0100 Pali Rohár [email protected] wrote:

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Probably the frame buffer memory allocation did not work. Could you please try with a bind callback, i.e.:

static int rx51_video_bind(struct udevice *dev)

Quoted 14 lines
{
	struct video_uc_plat *plat = dev_get_uclass_plat(dev);

	plat->size = 800 * 480 * 2;
	return 0;
}
...
U_BOOT_DRIVER(rx51_video) = {
	.name = "rx51_video",
	.id = UCLASS_VIDEO,
	.bind = rx51_video_bind,
	.probe = rx51_video_probe,
	.flags = DM_FLAG_PRE_RELOC,
};

Hello! It does not work too. Here is the output:

U-Boot 2022.04-rc2-00002-ga2c1a9878375-dirty (Jan 01 1970 - 00:00:00 +0000)

OMAP35XX-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz
DRAM: Video frame buffers from 8fe30000 to 8fe30000
256 MiB
Video device 'rx51_video' cannot allocate frame buffer memory -ensure the device is set up before relocation

If "return -ENOSPC;" is not commented then this is the last printed line. If it is commented then output continues with:

video_post_bind: Claiming 130000 bytes at 8fd00000 for video device 'rx51_video'

And framebuffer is working fine like without above rx51_video_bind() change.

Quoted 12 lines
Quoted 5 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

--
Anatolij

#4 lore raw

Hi Pali,

Quoted 51 lines · Pali Rohár

PING?

Quoted 47 lines · On Thursday 17 February 2022 13:20:43 Pali Rohár wrote:
Quoted 15 lines · On Thursday 17 February 2022 09:53:39 Anatolij Gustschin wrote:

Hi Pali,

Quoted 5 lines · On Wed, 16 Feb 2022 21:42:19 +0100 Pali Rohár [email protected] wrote:

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Probably the frame buffer memory allocation did not work. Could you please try with a bind callback, i.e.:

static int rx51_video_bind(struct udevice *dev)

Quoted 14 lines
{
    struct video_uc_plat *plat = dev_get_uclass_plat(dev);

    plat->size = 800 * 480 * 2;
    return 0;
}
...
U_BOOT_DRIVER(rx51_video) = {
    .name = "rx51_video",
    .id = UCLASS_VIDEO,
    .bind = rx51_video_bind,
    .probe = rx51_video_probe,
    .flags = DM_FLAG_PRE_RELOC,
};

Hello! It does not work too. Here is the output:

U-Boot 2022.04-rc2-00002-ga2c1a9878375-dirty (Jan 01 1970 - 00:00:00 +0000)

OMAP35XX-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz
DRAM: Video frame buffers from 8fe30000 to 8fe30000
256 MiB
Video device 'rx51_video' cannot allocate frame buffer memory -ensure the device is set up before relocation

If "return -ENOSPC;" is not commented then this is the last printed line. If it is commented then output continues with:

video_post_bind: Claiming 130000 bytes at 8fd00000 for video device 'rx51_video'

And framebuffer is working fine like without above rx51_video_bind() change.

It looks like you are hard-coding the address of the video buffers. Is that intentional? If so, you may need to disable U-Boot's automatic allocation.

One way to do that is to set the frame buffer address and size in your bind() routine (post relocation) and update video_post_bind() to check if the address is non-zero (plat->base I mean) and skip its allocation if so.

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 6 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Regards,
Simon

#5 lore raw
Quoted 50 lines · On Sunday 06 March 2022 05:51:34 Simon Glass wrote:

Hi Pali,

Quoted 47 lines · Pali Rohár

PING?

Quoted 43 lines · On Thursday 17 February 2022 13:20:43 Pali Rohár wrote:
Quoted 15 lines · On Thursday 17 February 2022 09:53:39 Anatolij Gustschin wrote:

Hi Pali,

Quoted 5 lines · On Wed, 16 Feb 2022 21:42:19 +0100 Pali Rohár [email protected] wrote:

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Probably the frame buffer memory allocation did not work. Could you please try with a bind callback, i.e.:

static int rx51_video_bind(struct udevice *dev)

Quoted 14 lines
{
    struct video_uc_plat *plat = dev_get_uclass_plat(dev);

    plat->size = 800 * 480 * 2;
    return 0;
}
...
U_BOOT_DRIVER(rx51_video) = {
    .name = "rx51_video",
    .id = UCLASS_VIDEO,
    .bind = rx51_video_bind,
    .probe = rx51_video_probe,
    .flags = DM_FLAG_PRE_RELOC,
};

Hello! It does not work too. Here is the output:

U-Boot 2022.04-rc2-00002-ga2c1a9878375-dirty (Jan 01 1970 - 00:00:00 +0000)

OMAP35XX-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz
DRAM: Video frame buffers from 8fe30000 to 8fe30000
256 MiB
Video device 'rx51_video' cannot allocate frame buffer memory -ensure the device is set up before relocation

If "return -ENOSPC;" is not commented then this is the last printed line. If it is commented then output continues with:

Quoted 8 lines
Quoted 4 lines
Quoted 4 lines

video_post_bind: Claiming 130000 bytes at 8fd00000 for video device 'rx51_video'

And framebuffer is working fine like without above rx51_video_bind() change.

It looks like you are hard-coding the address of the video buffers. Is that intentional? If so, you may need to disable U-Boot's automatic allocation.

This is how it works, signed bootloader which loads U-Boot initialize and prepare framebuffer.

Quoted 4 lines

One way to do that is to set the frame buffer address and size in your bind() routine (post relocation) and update video_post_bind() to check if the address is non-zero (plat->base I mean) and skip its allocation if so.

Ok, I have tried it and following change makes framebuffer in qemu working:

drivers/video/video-uclass.c +3 -0
index 7d499bcec51d..f4d8d395e714 100644
@@ -78,6 +80,9 @@ static ulong alloc_fb(struct udevice *dev, ulong *addrp)
 	if (!plat->size)
 		return 0;
 
+	if (plat->base)
+		return 0;
+
 	align = plat->align ? plat->align : 1 << 20;
 	base = *addrp - plat->size;
 	base &= ~(align - 1);

Is this what you mean?

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 1 line

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Does not work, logo is not drown on the screen.

#6 lore raw

Hi Pali,

Quoted 77 lines · Pali Rohár
Quoted 50 lines · On Sunday 06 March 2022 05:51:34 Simon Glass wrote:

Hi Pali,

Quoted 47 lines · Pali Rohár

PING?

Quoted 43 lines · On Thursday 17 February 2022 13:20:43 Pali Rohár wrote:
Quoted 15 lines · On Thursday 17 February 2022 09:53:39 Anatolij Gustschin wrote:

Hi Pali,

Quoted 5 lines · On Wed, 16 Feb 2022 21:42:19 +0100 Pali Rohár [email protected] wrote:

---
I had to comment "return -ENOSPC;" in video-uclass.c because without it DM_VIDEO does not work and I do not know why. This looks like either false-positive test or a bug in DM_VIDEO code. I have already set PRE_RELOC flag but it has no effect on that code.

Probably the frame buffer memory allocation did not work. Could you please try with a bind callback, i.e.:

static int rx51_video_bind(struct udevice *dev)

Quoted 14 lines
{
    struct video_uc_plat *plat = dev_get_uclass_plat(dev);

    plat->size = 800 * 480 * 2;
    return 0;
}
...
U_BOOT_DRIVER(rx51_video) = {
    .name = "rx51_video",
    .id = UCLASS_VIDEO,
    .bind = rx51_video_bind,
    .probe = rx51_video_probe,
    .flags = DM_FLAG_PRE_RELOC,
};

Hello! It does not work too. Here is the output:

U-Boot 2022.04-rc2-00002-ga2c1a9878375-dirty (Jan 01 1970 - 00:00:00 +0000)

OMAP35XX-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 600 MHz
DRAM: Video frame buffers from 8fe30000 to 8fe30000
256 MiB
Video device 'rx51_video' cannot allocate frame buffer memory -ensure the device is set up before relocation

If "return -ENOSPC;" is not commented then this is the last printed line. If it is commented then output continues with:

Quoted 8 lines
Quoted 4 lines
Quoted 4 lines

video_post_bind: Claiming 130000 bytes at 8fd00000 for video device 'rx51_video'

And framebuffer is working fine like without above rx51_video_bind() change.

It looks like you are hard-coding the address of the video buffers. Is that intentional? If so, you may need to disable U-Boot's automatic allocation.

This is how it works, signed bootloader which loads U-Boot initialize and prepare framebuffer.

Quoted 4 lines

One way to do that is to set the frame buffer address and size in your bind() routine (post relocation) and update video_post_bind() to check if the address is non-zero (plat->base I mean) and skip its allocation if so.

Ok, I have tried it and following change makes framebuffer in qemu working:

drivers/video/video-uclass.c +0 -0
index 7d499bcec51d..f4d8d395e714 100644

drivers/video/video-uclass.c static ulong alloc_fb(struct udevice *dev, ulong *addrp) · line 85

Quoted 6 lines
drivers/video/video-uclass.c +3 -0
@@ -78,6 +80,9 @@ static ulong alloc_fb(struct udevice *dev, ulong *addrp)
        if (!plat->size)
                return 0;
 
+       if (plat->base)
+               return 0;
+

Yes let's go with that.

Quoted 13 lines
drivers/video/video-uclass.c +0 -0
        align = plat->align ? plat->align : 1 << 20;
        base = *addrp - plat->size;
        base &= ~(align - 1);

Is this what you mean?

Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 6 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported? Anyway you should be able to debug it there or using the bmp command. The file is drivers/video/u_boot_logo.bmp

Regards,
Simon

#14 lore raw

PATCH 1/1 Nokia RX-51: Convert to CONFIG_DM_VIDEO

In reply to Pali Rohár

Mechanically convert video_hw_init() function to UCLASS_VIDEO probe callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.

As framebuffer base address is setup by the bootloader which loads U-Boot, set it into plat->base. And do not allocate framebuffer in video_post_bind function when base address is already specified.

This change was tested in qemu n900 machine and is working fine.

What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.

---
 board/nokia/rx51/rx51.c      | 40 +++++++++++++++++++++---------------
 configs/nokia_rx51_defconfig |  7 +++++--
 drivers/video/video-uclass.c |  3 +++
 include/configs/nokia_rx51.h | 11 ++--------
 4 files changed, 34 insertions(+), 27 deletions(-)
board/nokia/rx51/rx51.c +24 -16
index a52691509da4..621cff095619 100644
@@ -30,7 +30,7 @@
 #include <malloc.h>
 #include <twl4030.h>
 #include <i2c.h>
-#include <video_fb.h>
+#include <video.h>
 #include <keyboard.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
@@ -62,8 +62,6 @@ struct emu_hal_params_rx51 {
 
 DECLARE_GLOBAL_DATA_PTR;
 
-GraphicDevice gdev;
-
 const omap3_sysinfo sysinfo = {
 	DDR_STACKED,
 	"Nokia RX-51",
@@ -342,22 +340,28 @@ void setup_board_tags(struct tag **in_params)
 	*in_params = params;
 }
 
-/*
- * Routine: video_hw_init
- * Description: Set up the GraphicDevice depending on sys_boot.
- */
-void *video_hw_init(void)
+static int rx51_video_probe(struct udevice *dev)
 {
-	/* fill in Graphic Device */
-	gdev.frameAdrs = 0x8f9c0000;
-	gdev.winSizeX = 800;
-	gdev.winSizeY = 480;
-	gdev.gdfBytesPP = 2;
-	gdev.gdfIndex = GDF_16BIT_565RGB;
-	memset((void *)gdev.frameAdrs, 0, 0xbb800);
-	return (void *) &gdev;
+	struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+	struct video_priv *uc_priv = dev_get_uclass_priv(dev);
+
+	uc_plat->base = 0x8f9c0000;
+	uc_plat->size = 800 * 480 * sizeof(u16);
+	uc_priv->xsize = 800;
+	uc_priv->ysize = 480;
+	uc_priv->bpix = VIDEO_BPP16;
+
+	video_set_flush_dcache(dev, true);
+
+	return 0;
 }
 
+U_BOOT_DRIVER(rx51_video) = {
+	.name = "rx51_video",
+	.id = UCLASS_VIDEO,
+	.probe = rx51_video_probe,
+};
+
 /*
  * Routine: twl4030_regulator_set_mode
  * Description: Set twl4030 regulator mode over i2c powerbus.
@@ -777,6 +781,10 @@ U_BOOT_DRVINFOS(rx51_watchdog) = {
 	{ "rx51_watchdog" },
 };
 
+U_BOOT_DRVINFOS(rx51_video) = {
+	{ "rx51_video" },
+};
+
 U_BOOT_DRVINFOS(rx51_kp) = {
 	{ "rx51_kp" },
 };
configs/nokia_rx51_defconfig +5 -2
index 47b7bc3b4f03..1d64981afc46 100644
@@ -77,8 +77,11 @@ CONFIG_SPI=y
 CONFIG_USB=y
 CONFIG_USB_MUSB_UDC=y
 CONFIG_USB_OMAP3=y
-CONFIG_CFB_CONSOLE=y
-CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_LOGO=y
+# CONFIG_VIDEO_BPP8 is not set
+# CONFIG_VIDEO_BPP32 is not set
+CONFIG_SYS_WHITE_ON_BLACK=y
 CONFIG_SPLASH_SCREEN=y
 CONFIG_WATCHDOG_TIMEOUT_MSECS=31000
 CONFIG_WDT=y
drivers/video/video-uclass.c +3 -0
index 7d499bcec51d..c2f7d97e93e3 100644
@@ -78,6 +78,9 @@ static ulong alloc_fb(struct udevice *dev, ulong *addrp)
 	if (!plat->size)
 		return 0;
 
+	if (plat->base)
+		return 0;
+
 	align = plat->align ? plat->align : 1 << 20;
 	base = *addrp - plat->size;
 	base &= ~(align - 1);
include/configs/nokia_rx51.h +2 -9
index 9be64c3d3f87..e837b12b568f 100644
@@ -70,19 +70,12 @@
 
 #define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
 
-/*
- * Framebuffer
- */
-/* Video console */
-#define VIDEO_FB_16BPP_PIXEL_SWAP
-#define VIDEO_FB_16BPP_WORD_SWAP
-
 /* Environment information */
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"usbtty=cdc_acm\0" \
 	"stdin=usbtty,serial,keyboard\0" \
-	"stdout=usbtty,serial,vga\0" \
-	"stderr=usbtty,serial,vga\0" \
+	"stdout=usbtty,serial,vidconsole\0" \
+	"stderr=usbtty,serial,vidconsole\0" \
 	"slide=gpio input " __stringify(GPIO_SLIDE) "\0" \
 	"switchmmc=mmc dev ${mmcnum}\0" \
 	"kernaddr=0x82008000\0" \
Signature · 1 line
2.20.1
#7 lore raw
In reply to Simon Glass
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Quoted 6 lines
Quoted 3 lines
Quoted 1 line

Can you be more specific than 'broken'? What is broken about it?

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

Quoted 2 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

#15 lore raw

Re: [PATCH] Nokia RX-51: Convert to CONFIG_DM_VIDEO

In reply to Pali Rohár

Hi Pali,

Quoted 55 lines · Pali Rohár

Mechanically convert video_hw_init() function to UCLASS_VIDEO probe callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.

As framebuffer base address is setup by the bootloader which loads U-Boot, set it into plat->base. And do not allocate framebuffer in video_post_bind function when base address is already specified.

This change was tested in qemu n900 machine and is working fine.

What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.

---
 board/nokia/rx51/rx51.c      | 40 +++++++++++++++++++++---------------
 configs/nokia_rx51_defconfig |  7 +++++--
 drivers/video/video-uclass.c |  3 +++
 include/configs/nokia_rx51.h | 11 ++--------
 4 files changed, 34 insertions(+), 27 deletions(-)
board/nokia/rx51/rx51.c +2 -10
index a52691509da4..621cff095619 100644
@@ -30,7 +30,7 @@
 #include <malloc.h>
 #include <twl4030.h>
 #include <i2c.h>
-#include <video_fb.h>
+#include <video.h>
 #include <keyboard.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
@@ -62,8 +62,6 @@ struct emu_hal_params_rx51 {
 
 DECLARE_GLOBAL_DATA_PTR;
 
-GraphicDevice gdev;
-
 const omap3_sysinfo sysinfo = {
        DDR_STACKED,
        "Nokia RX-51",
@@ -342,22 +340,28 @@ void setup_board_tags(struct tag **in_params)
        *in_params = params;
 }
 
-/*
- * Routine: video_hw_init
- * Description: Set up the GraphicDevice depending on sys_boot.
- */
-void *video_hw_init(void)
+static int rx51_video_probe(struct udevice *dev)
 {
-       /* fill in Graphic Device */
-       gdev.frameAdrs = 0x8f9c0000;

board/nokia/rx51/rx51.c void setup_board_tags(struct tag **in_params) · line 348

Quoted 10 lines
board/nokia/rx51/rx51.c +4 -6
-       gdev.winSizeX = 800;
-       gdev.winSizeY = 480;
-       gdev.gdfBytesPP = 2;
-       gdev.gdfIndex = GDF_16BIT_565RGB;
-       memset((void *)gdev.frameAdrs, 0, 0xbb800);
-       return (void *) &gdev;
+       struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+       struct video_priv *uc_priv = dev_get_uclass_priv(dev);
+
+       uc_plat->base = 0x8f9c0000;

How is this calculated?

board/nokia/rx51/rx51.c void setup_board_tags(struct tag **in_params) · line 349

Quoted 1 line
board/nokia/rx51/rx51.c +1 -0
+       uc_plat->size = 800 * 480 * sizeof(u16);

More correctly this should be in the bind() method, but in fact I don't think it matters. We can always adjust it later if needed.

Quoted 52 lines
board/nokia/rx51/rx51.c +17 -0
+       uc_priv->xsize = 800;
+       uc_priv->ysize = 480;
+       uc_priv->bpix = VIDEO_BPP16;
+
+       video_set_flush_dcache(dev, true);
+
+       return 0;
 }
 
+U_BOOT_DRIVER(rx51_video) = {
+       .name = "rx51_video",
+       .id = UCLASS_VIDEO,
+       .probe = rx51_video_probe,
+};
+
 /*
  * Routine: twl4030_regulator_set_mode
  * Description: Set twl4030 regulator mode over i2c powerbus.
@@ -777,6 +781,10 @@ U_BOOT_DRVINFOS(rx51_watchdog) = {
        { "rx51_watchdog" },
 };
 
+U_BOOT_DRVINFOS(rx51_video) = {
+       { "rx51_video" },
+};
+
 U_BOOT_DRVINFOS(rx51_kp) = {
        { "rx51_kp" },
 };
configs/nokia_rx51_defconfig +5 -2
index 47b7bc3b4f03..1d64981afc46 100644
@@ -77,8 +77,11 @@ CONFIG_SPI=y
 CONFIG_USB=y
 CONFIG_USB_MUSB_UDC=y
 CONFIG_USB_OMAP3=y
-CONFIG_CFB_CONSOLE=y
-CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_LOGO=y
+# CONFIG_VIDEO_BPP8 is not set
+# CONFIG_VIDEO_BPP32 is not set
+CONFIG_SYS_WHITE_ON_BLACK=y
 CONFIG_SPLASH_SCREEN=y
 CONFIG_WATCHDOG_TIMEOUT_MSECS=31000
 CONFIG_WDT=y
drivers/video/video-uclass.c +0 -0
index 7d499bcec51d..c2f7d97e93e3 100644

drivers/video/video-uclass.c static ulong alloc_fb(struct udevice *dev, ulong *addrp) · line 83

Quoted 6 lines
drivers/video/video-uclass.c +3 -0
@@ -78,6 +78,9 @@ static ulong alloc_fb(struct udevice *dev, ulong *addrp)
        if (!plat->size)
                return 0;
 
+       if (plat->base)
+               return 0;
+

How about a comment there like:

/* Allow drivers to allocate the frame buffer themselves */

Please put this change in its own video: patch and update the comment at the top of video-uclass.c and the comment for @base in video.h so the next person can figure this out.

Quoted 30 lines
drivers/video/video-uclass.c +0 -0
        align = plat->align ? plat->align : 1 << 20;
        base = *addrp - plat->size;
        base &= ~(align - 1);
include/configs/nokia_rx51.h +2 -10
index 9be64c3d3f87..e837b12b568f 100644
@@ -70,19 +70,12 @@
 
 #define CONFIG_SYS_ONENAND_BASE                ONENAND_MAP
 
-/*
- * Framebuffer
- */
-/* Video console */
-#define VIDEO_FB_16BPP_PIXEL_SWAP
-#define VIDEO_FB_16BPP_WORD_SWAP
-
 /* Environment information */
 #define CONFIG_EXTRA_ENV_SETTINGS \
        "usbtty=cdc_acm\0" \
        "stdin=usbtty,serial,keyboard\0" \
-       "stdout=usbtty,serial,vga\0" \
-       "stderr=usbtty,serial,vga\0" \
+       "stdout=usbtty,serial,vidconsole\0" \
+       "stderr=usbtty,serial,vidconsole\0" \
        "slide=gpio input " __stringify(GPIO_SLIDE) "\0" \
        "switchmmc=mmc dev ${mmcnum}\0" \
        "kernaddr=0x82008000\0" \
--
Quoted 2 lines

2.20.1

Regards,
Simon

#8 lore raw
In reply to Pali Rohár

Hi Pali,

Quoted 15 lines · Pali Rohár
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
Quoted 1 line

Can you be more specific than 'broken'? What is broken about it?

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

But apparently isn't , at least in this case :-)

Quoted 6 lines
Quoted 3 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

OK I'm not sure why, but please investigate if you have time.

Regards,
Simon

#16 lore raw

Re: [PATCH] Nokia RX-51: Convert to CONFIG_DM_VIDEO

In reply to Simon Glass
Quoted 14 lines · On Sunday 06 March 2022 11:43:21 Simon Glass wrote:
Quoted 13 lines · Pali Rohár
board/nokia/rx51/rx51.c +1 -11
-/*
- * Routine: video_hw_init
- * Description: Set up the GraphicDevice depending on sys_boot.
- */
-void *video_hw_init(void)
+static int rx51_video_probe(struct udevice *dev)
 {
-       /* fill in Graphic Device */
-       gdev.frameAdrs = 0x8f9c0000;
-       gdev.winSizeX = 800;
-       gdev.winSizeY = 480;
-       gdev.gdfBytesPP = 2;
-       gdev.gdfIndex = GDF_16BIT_565RGB;
Quoted 8 lines

board/nokia/rx51/rx51.c void setup_board_tags(struct tag **in_params) · line 348

Quoted 6 lines
board/nokia/rx51/rx51.c +4 -2
-       memset((void *)gdev.frameAdrs, 0, 0xbb800);
-       return (void *) &gdev;
+       struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+       struct video_priv *uc_priv = dev_get_uclass_priv(dev);
+
+       uc_plat->base = 0x8f9c0000;

How is this calculated?

I do not remember. This seems to be fixed address set by the code which loads U-Boot. I do not have any notes about this stuff.

Quoted 4 lines
Quoted 1 line

+ uc_plat->size = 800 * 480 * sizeof(u16);

More correctly this should be in the bind() method, but in fact I don't think it matters. We can always adjust it later if needed.

Ok. I let it in probe, so all initialization is done at one place. If something is needed to adjust, it can be done later.

#9 lore raw
In reply to Simon Glass
Quoted 20 lines · On Sunday 06 March 2022 11:44:22 Simon Glass wrote:

Hi Pali,

Quoted 17 lines · Pali Rohár
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 11 lines
Quoted 11 lines
Quoted 10 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

But apparently isn't , at least in this case :-)

Yea, something is broken there.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

OK I'm not sure why, but please investigate if you have time.

I have looked at it and do not know. But probably it is because I somehow have not caught how this new video code works...

Anyway, I sent documentation update how to run u-boot for n900 in qemu:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

So it could help other people to look at issues which do not work correctly in n900's u-boot without need to have n900 hardware.

#17 lore raw

PATCH v2 1/2 video: Allow drivers to allocate the frame buffer themselves

In reply to Pali Rohár

When plat->base is set by driver then skip frame buffer reservation and allocation.

---
 drivers/video/video-uclass.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
drivers/video/video-uclass.c +6 -1
index 7d499bcec51d..88797d4a21c2 100644
@@ -33,7 +33,8 @@
  * information represents the requires size and alignment of the frame buffer
  * for the device. The values can be an over-estimate but cannot be too
  * small. The actual values will be suppled (in the same manner) by the bind()
- * method after relocation.
+ * method after relocation. Additionally driver can allocate frame buffer
+ * itself by setting plat->base.
  *
  * This information is then picked up by video_reserve() which works out how
  * much memory is needed for all devices. This is allocated between
@@ -78,6 +79,10 @@ static ulong alloc_fb(struct udevice *dev, ulong *addrp)
 	if (!plat->size)
 		return 0;
 
+	/* Allow drivers to allocate the frame buffer themselves */
+	if (plat->base)
+		return 0;
+
 	align = plat->align ? plat->align : 1 << 20;
 	base = *addrp - plat->size;
 	base &= ~(align - 1);
Signature · 1 line
2.20.1
#18 lore raw

PATCH v2 2/2 Nokia RX-51: Convert to CONFIG_DM_VIDEO

Mechanically convert video_hw_init() function to UCLASS_VIDEO probe callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.

As framebuffer base address is setup by the bootloader which loads U-Boot, set plat->base to that fixed framebuffer address.

This change was tested in qemu n900 machine and is working fine.

What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.

---
 board/nokia/rx51/rx51.c      | 40 +++++++++++++++++++++---------------
 configs/nokia_rx51_defconfig |  7 +++++--
 include/configs/nokia_rx51.h | 11 ++--------
 3 files changed, 31 insertions(+), 27 deletions(-)
board/nokia/rx51/rx51.c +24 -16
index a52691509da4..621cff095619 100644
@@ -30,7 +30,7 @@
 #include <malloc.h>
 #include <twl4030.h>
 #include <i2c.h>
-#include <video_fb.h>
+#include <video.h>
 #include <keyboard.h>
 #include <asm/global_data.h>
 #include <asm/io.h>
@@ -62,8 +62,6 @@ struct emu_hal_params_rx51 {
 
 DECLARE_GLOBAL_DATA_PTR;
 
-GraphicDevice gdev;
-
 const omap3_sysinfo sysinfo = {
 	DDR_STACKED,
 	"Nokia RX-51",
@@ -342,22 +340,28 @@ void setup_board_tags(struct tag **in_params)
 	*in_params = params;
 }
 
-/*
- * Routine: video_hw_init
- * Description: Set up the GraphicDevice depending on sys_boot.
- */
-void *video_hw_init(void)
+static int rx51_video_probe(struct udevice *dev)
 {
-	/* fill in Graphic Device */
-	gdev.frameAdrs = 0x8f9c0000;
-	gdev.winSizeX = 800;
-	gdev.winSizeY = 480;
-	gdev.gdfBytesPP = 2;
-	gdev.gdfIndex = GDF_16BIT_565RGB;
-	memset((void *)gdev.frameAdrs, 0, 0xbb800);
-	return (void *) &gdev;
+	struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+	struct video_priv *uc_priv = dev_get_uclass_priv(dev);
+
+	uc_plat->base = 0x8f9c0000;
+	uc_plat->size = 800 * 480 * sizeof(u16);
+	uc_priv->xsize = 800;
+	uc_priv->ysize = 480;
+	uc_priv->bpix = VIDEO_BPP16;
+
+	video_set_flush_dcache(dev, true);
+
+	return 0;
 }
 
+U_BOOT_DRIVER(rx51_video) = {
+	.name = "rx51_video",
+	.id = UCLASS_VIDEO,
+	.probe = rx51_video_probe,
+};
+
 /*
  * Routine: twl4030_regulator_set_mode
  * Description: Set twl4030 regulator mode over i2c powerbus.
@@ -777,6 +781,10 @@ U_BOOT_DRVINFOS(rx51_watchdog) = {
 	{ "rx51_watchdog" },
 };
 
+U_BOOT_DRVINFOS(rx51_video) = {
+	{ "rx51_video" },
+};
+
 U_BOOT_DRVINFOS(rx51_kp) = {
 	{ "rx51_kp" },
 };
configs/nokia_rx51_defconfig +5 -2
index 47b7bc3b4f03..1d64981afc46 100644
@@ -77,8 +77,11 @@ CONFIG_SPI=y
 CONFIG_USB=y
 CONFIG_USB_MUSB_UDC=y
 CONFIG_USB_OMAP3=y
-CONFIG_CFB_CONSOLE=y
-CONFIG_CFB_CONSOLE_ANSI=y
+CONFIG_DM_VIDEO=y
+CONFIG_VIDEO_LOGO=y
+# CONFIG_VIDEO_BPP8 is not set
+# CONFIG_VIDEO_BPP32 is not set
+CONFIG_SYS_WHITE_ON_BLACK=y
 CONFIG_SPLASH_SCREEN=y
 CONFIG_WATCHDOG_TIMEOUT_MSECS=31000
 CONFIG_WDT=y
include/configs/nokia_rx51.h +2 -9
index 9be64c3d3f87..e837b12b568f 100644
@@ -70,19 +70,12 @@
 
 #define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP
 
-/*
- * Framebuffer
- */
-/* Video console */
-#define VIDEO_FB_16BPP_PIXEL_SWAP
-#define VIDEO_FB_16BPP_WORD_SWAP
-
 /* Environment information */
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"usbtty=cdc_acm\0" \
 	"stdin=usbtty,serial,keyboard\0" \
-	"stdout=usbtty,serial,vga\0" \
-	"stderr=usbtty,serial,vga\0" \
+	"stdout=usbtty,serial,vidconsole\0" \
+	"stderr=usbtty,serial,vidconsole\0" \
 	"slide=gpio input " __stringify(GPIO_SLIDE) "\0" \
 	"switchmmc=mmc dev ${mmcnum}\0" \
 	"kernaddr=0x82008000\0" \
Signature · 1 line
2.20.1
#10 lore raw
In reply to Pali Rohár

Hi Pali,

Quoted 41 lines · On Wed, 9 Mar 2022 20:44:50 +0100 Pali Rohár [email protected] wrote:
Quoted 20 lines · On Sunday 06 March 2022 11:44:22 Simon Glass wrote:

Hi Pali,

Quoted 17 lines · Pali Rohár
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 11 lines
Quoted 11 lines
Quoted 10 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

But apparently isn't , at least in this case :-)

Yea, something is broken there.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

OK I'm not sure why, but please investigate if you have time.

Quoted 8 lines

I have looked at it and do not know. But probably it is because I somehow have not caught how this new video code works...

Anyway, I sent documentation update how to run u-boot for n900 in qemu:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

So it could help other people to look at issues which do not work correctly in n900's u-boot without need to have n900 hardware.

I've tested your v2 patches, and logo drawing works, but the logo appears for short time. Then it is later overwritten by boot menu.

--
Anatolij

#11 lore raw
Quoted 52 lines · On Wednesday 09 March 2022 23:20:11 Anatolij Gustschin wrote:

Hi Pali,

Quoted 47 lines · On Wed, 9 Mar 2022 20:44:50 +0100 Pali Rohár [email protected] wrote:
Quoted 20 lines · On Sunday 06 March 2022 11:44:22 Simon Glass wrote:

Hi Pali,

Quoted 17 lines · Pali Rohár
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 11 lines
Quoted 11 lines
Quoted 10 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

But apparently isn't , at least in this case :-)

Yea, something is broken there.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

OK I'm not sure why, but please investigate if you have time.

I have looked at it and do not know. But probably it is because I somehow have not caught how this new video code works...

Anyway, I sent documentation update how to run u-boot for n900 in qemu:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

Quoted 8 lines
Quoted 2 lines

So it could help other people to look at issues which do not work correctly in n900's u-boot without need to have n900 hardware.

I've tested your v2 patches, and logo drawing works, but the logo appears for short time. Then it is later overwritten by boot menu.

--
Anatolij

Hello! Thank you for checking. It is possible that qemu rending is slower and reason why I did not see any logo.

Anyway, this is now how CONFIG_VIDEO_LOGO worked. In previous U-Boot version it drew logo on the screen and it was visible also in the boot menu.

Any idea what was changed? Or is there missing some another config option to make logo visible?

#12 lore raw
In reply to Pali Rohár

Hi Pali,

Quoted 66 lines · Pali Rohár
Quoted 52 lines · On Wednesday 09 March 2022 23:20:11 Anatolij Gustschin wrote:

Hi Pali,

Quoted 47 lines · On Wed, 9 Mar 2022 20:44:50 +0100 Pali Rohár [email protected] wrote:
Quoted 20 lines · On Sunday 06 March 2022 11:44:22 Simon Glass wrote:

Hi Pali,

Quoted 17 lines · Pali Rohár
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 11 lines
Quoted 11 lines
Quoted 10 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

But apparently isn't , at least in this case :-)

Yea, something is broken there.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

OK I'm not sure why, but please investigate if you have time.

I have looked at it and do not know. But probably it is because I somehow have not caught how this new video code works...

Anyway, I sent documentation update how to run u-boot for n900 in qemu:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

Quoted 8 lines
Quoted 2 lines

So it could help other people to look at issues which do not work correctly in n900's u-boot without need to have n900 hardware.

I've tested your v2 patches, and logo drawing works, but the logo appears for short time. Then it is later overwritten by boot menu.

--
Anatolij

Hello! Thank you for checking. It is possible that qemu rending is slower and reason why I did not see any logo.

Quoted 6 lines

Anyway, this is now how CONFIG_VIDEO_LOGO worked. In previous U-Boot version it drew logo on the screen and it was visible also in the boot menu.

Any idea what was changed? Or is there missing some another config option to make logo visible?

I believe the cfb_console code had a way to keep the logo at the top with the text scrolling underneath. This has not been implemented in the video/vidconsole uclasses, although I suppose it could be.

Regards,
Simon

#13 lore raw
Quoted 76 lines · On Friday 11 March 2022 22:02:39 Simon Glass wrote:

Hi Pali,

Quoted 66 lines · Pali Rohár
Quoted 52 lines · On Wednesday 09 March 2022 23:20:11 Anatolij Gustschin wrote:

Hi Pali,

Quoted 47 lines · On Wed, 9 Mar 2022 20:44:50 +0100 Pali Rohár [email protected] wrote:
Quoted 20 lines · On Sunday 06 March 2022 11:44:22 Simon Glass wrote:

Hi Pali,

Quoted 17 lines · Pali Rohár
Quoted 1 line · On Sunday 06 March 2022 07:42:03 Simon Glass wrote:

Yes let's go with that.

Done, I sent final version of the patch.

Quoted 11 lines
Quoted 11 lines
Quoted 10 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines

Second thing is that CONFIG_VIDEO_LOGO is broken and does not work even it
is enabled in config file. I do not know why too.

Any idea?

Not yet. There were some logo related changes recently, but if I remember correctly, I tested them on wandboard and nitrogen6q targets and with sandbox, and logo drawing worked there.

Can you be more specific than 'broken'? What is broken about it?

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 1 line

Does not work, logo is not drown on the screen.

See video_bmp_display() - I wonder if the particular depth you are using is not supported?

Depth is 16bit which should be supported.

But apparently isn't , at least in this case :-)

Yea, something is broken there.

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

Anyway you should be able to debug it there or
using the bmp command. The file is drivers/video/u_boot_logo.bmp

CONFIG_CMD_BMP=y is broken too. When I enable it then U-Boot freeze after the line 'Loading Environment from <NULL>... OK'.

OK I'm not sure why, but please investigate if you have time.

I have looked at it and do not know. But probably it is because I somehow have not caught how this new video code works...

Anyway, I sent documentation update how to run u-boot for n900 in qemu:
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

Quoted 8 lines
Quoted 2 lines

So it could help other people to look at issues which do not work correctly in n900's u-boot without need to have n900 hardware.

I've tested your v2 patches, and logo drawing works, but the logo appears for short time. Then it is later overwritten by boot menu.

--
Anatolij

Hello! Thank you for checking. It is possible that qemu rending is slower and reason why I did not see any logo.

Quoted 6 lines

Anyway, this is now how CONFIG_VIDEO_LOGO worked. In previous U-Boot version it drew logo on the screen and it was visible also in the boot menu.

Any idea what was changed? Or is there missing some another config option to make logo visible?

Quoted 6 lines

I believe the cfb_console code had a way to keep the logo at the top with the text scrolling underneath. This has not been implemented in the video/vidconsole uclasses, although I suppose it could be.

Regards,
Simon

Ok!

#21 lore raw

Re: [PATCH v2 1/2] video: Allow drivers to allocate the frame buffer themselves

In reply to Pali Rohár
Quoted 6 lines · On Wed, 9 Mar 2022 20:46:00 +0100 Pali Rohár [email protected] wrote:

When plat->base is set by driver then skip frame buffer reservation and allocation.

---
 drivers/video/video-uclass.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

applied to u-boot-video/master, thanks!

--
Anatolij

#19 lore raw

Re: [PATCH v2 2/2] Nokia RX-51: Convert to CONFIG_DM_VIDEO

In reply to Pali Rohár

On Wed, 9 Mar 2022 20:46:01 +0100
Pali Rohár [email protected] wrote:
...

Quoted 5 lines
---
 board/nokia/rx51/rx51.c      | 40 +++++++++++++++++++++---------------
 configs/nokia_rx51_defconfig |  7 +++++--
 include/configs/nokia_rx51.h | 11 ++--------
 3 files changed, 31 insertions(+), 27 deletions(-)

applied to u-boot-video/master, thanks!

--
Anatolij