Skip to contentSkip to conversation

TI: Add support for AM62 SoC

PATCH Superseded Vignesh Raghavendra 4 participants 24 messages Apr 15, 2022 – Apr 18, 2022

Subsystems (10)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Vignesh Raghavendra

author maintainer
#0 lore raw

cover TI: Add support for AM62 SoC

This adds basic support for TI's new AM62 family of SoCs and AM625 Starter Kit EVM with SD boot and networking support at U-Boot prompt

Aswath Govindraju (1):
drivers: mmc: am654_sdhci: Add new compatible for AM62 SoC

Nishanth Menon (1):
arm: dts: Add support for AM62-SK

Suman Anna (6):
dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62
soc: ti: k3-socinfo: Add entry for AM62X SoC family
arm: mach-k3: Introduce the basic files to support AM62
arm: mach-k3: am62: Introduce autogenerated SoC data
arm: dts: Introduce base AM62 SoC dtsi files
board: ti: Introduce the basic files to support AM62 SK board

Vignesh Raghavendra (3):
dma: ti: Add PSIL data for AM62x DMASS
configs: Add configs for AM62x SK
doc: ti: Add readme for AM62x SK

 arch/arm/dts/Makefile                         |    3 +
 arch/arm/dts/k3-am62-ddr.dtsi                 |   11 +
 arch/arm/dts/k3-am62-main.dtsi                |  533 ++++
 arch/arm/dts/k3-am62-mcu.dtsi                 |   56 +
 arch/arm/dts/k3-am62-wakeup.dtsi              |   41 +
 arch/arm/dts/k3-am62.dtsi                     |  105 +
 arch/arm/dts/k3-am625-r5-sk.dts               |  130 +
 arch/arm/dts/k3-am625-sk-u-boot.dtsi          |  124 +
 arch/arm/dts/k3-am625-sk.dts                  |  469 ++++
 arch/arm/dts/k3-am625.dtsi                    |  103 +
 arch/arm/dts/k3-am62x-sk-ddr4-1600MTs.dtsi    | 2189 +++++++++++++++++
 arch/arm/mach-k3/Kconfig                      |   10 +-
 arch/arm/mach-k3/Makefile                     |    1 +
 arch/arm/mach-k3/am625_init.c                 |  254 ++
 arch/arm/mach-k3/am62x/Makefile               |    6 +
 arch/arm/mach-k3/am62x/clk-data.c             |  366 +++
 arch/arm/mach-k3/am62x/dev-data.c             |   78 +
 arch/arm/mach-k3/arm64-mmu.c                  |    4 +-
 arch/arm/mach-k3/include/mach/am62_hardware.h |   66 +
 arch/arm/mach-k3/include/mach/am62_spl.h      |   44 +
 arch/arm/mach-k3/include/mach/hardware.h      |    4 +
 arch/arm/mach-k3/include/mach/spl.h           |    5 +
 board/ti/am62x/Kconfig                        |   63 +
 board/ti/am62x/MAINTAINERS                    |    8 +
 board/ti/am62x/Makefile                       |    8 +
 board/ti/am62x/evm.c                          |  149 ++
 configs/am62x_evm_a53_defconfig               |  110 +
 configs/am62x_evm_r5_defconfig                |  114 +
 doc/board/ti/am62x_sk.rst                     |  231 ++
 doc/board/ti/index.rst                        |    1 +
 drivers/clk/ti/clk-k3.c                       |    6 +
 drivers/dma/ti/Makefile                       |    1 +
 drivers/dma/ti/k3-psil-am62.c                 |   50 +
 drivers/dma/ti/k3-psil-priv.h                 |    1 +
 drivers/dma/ti/k3-psil.c                      |    2 +
 drivers/firmware/ti_sci_static_data.h         |    7 +
 drivers/mmc/am654_sdhci.c                     |    4 +
 drivers/power/domain/ti-power-domain.c        |    6 +
 drivers/ram/Kconfig                           |    1 +
 drivers/soc/soc_ti_k3.c                       |    4 +
 include/configs/am62x_evm.h                   |  106 +
 include/dt-bindings/pinctrl/k3.h              |    3 +
 include/k3-clk.h                              |    1 +
 include/k3-dev.h                              |    1 +
 44 files changed, 5476 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/dts/k3-am62-ddr.dtsi
 create mode 100644 arch/arm/dts/k3-am62-main.dtsi
 create mode 100644 arch/arm/dts/k3-am62-mcu.dtsi
 create mode 100644 arch/arm/dts/k3-am62-wakeup.dtsi
 create mode 100644 arch/arm/dts/k3-am62.dtsi
 create mode 100644 arch/arm/dts/k3-am625-r5-sk.dts
 create mode 100644 arch/arm/dts/k3-am625-sk-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-am625-sk.dts
 create mode 100644 arch/arm/dts/k3-am625.dtsi
 create mode 100644 arch/arm/dts/k3-am62x-sk-ddr4-1600MTs.dtsi
 create mode 100644 arch/arm/mach-k3/am625_init.c
 create mode 100644 arch/arm/mach-k3/am62x/Makefile
 create mode 100644 arch/arm/mach-k3/am62x/clk-data.c
 create mode 100644 arch/arm/mach-k3/am62x/dev-data.c
 create mode 100644 arch/arm/mach-k3/include/mach/am62_hardware.h
 create mode 100644 arch/arm/mach-k3/include/mach/am62_spl.h
 create mode 100644 board/ti/am62x/Kconfig
 create mode 100644 board/ti/am62x/MAINTAINERS
 create mode 100644 board/ti/am62x/Makefile
 create mode 100644 board/ti/am62x/evm.c
 create mode 100644 configs/am62x_evm_a53_defconfig
 create mode 100644 configs/am62x_evm_r5_defconfig
 create mode 100644 doc/board/ti/am62x_sk.rst
 create mode 100644 drivers/dma/ti/k3-psil-am62.c
 create mode 100644 include/configs/am62x_evm.h
Signature · 1 line
2.35.3
author maintainer
#1 lore raw

PATCH 1/11 drivers: mmc: am654_sdhci: Add new compatible for AM62 SoC

From: Aswath Govindraju <[email protected]>

The phy used in the 8 bit instance has been changed to the phy used in 4 bit instance on AM62 SoC. This implies the phy configuration required for both the instances of mmc are similar. Therefore, add a new compatible for AM62 SoC using the driver data of am64 4 bit instance.

---
 drivers/mmc/am654_sdhci.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/mmc/am654_sdhci.c +4 -0
index 4305967d78..42a6134364 100644
@@ -670,6 +670,10 @@ static const struct udevice_id am654_sdhci_ids[] = {
 		.compatible = "ti,am64-sdhci-4bit",
 		.data = (ulong)&sdhci_am64_4bit_drvdata,
 	},
+	{
+		.compatible = "ti,am62-sdhci",
+		.data = (ulong)&sdhci_am64_4bit_drvdata,
+	},
 	{ }
 };
 
Signature · 1 line
2.35.3
author maintainer
#2 lore raw

PATCH 2/11 dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62

In reply to Vignesh Raghavendra

From: Suman Anna <[email protected]>

Add pinctrl macros for AM62x SoCs. These macro definitions are similar to that of previous platforms, but adding new definitions to avoid any naming confusions in the SoC dts files.

checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses

However, we do not need parentheses enclosing the values for this macro as we do intend it to generate two separate values as has been
done for other similar platforms.

---
 include/dt-bindings/pinctrl/k3.h | 3 +++
 1 file changed, 3 insertions(+)
include/dt-bindings/pinctrl/k3.h +3 -0
index 63e038e36c..a5204ab91d 100644
@@ -41,4 +41,7 @@
 #define J721S2_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
 #define J721S2_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
 
+#define AM62X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
 #endif
Signature · 1 line
2.35.3
#3 lore raw

Re: [PATCH 02/11] dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62

Quoted 24 lines · Vignesh Raghavendra

From: Suman Anna <[email protected]>

Add pinctrl macros for AM62x SoCs. These macro definitions are similar to that of previous platforms, but adding new definitions to avoid any naming confusions in the SoC dts files.

checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses

However, we do not need parentheses enclosing the values for this macro as we do intend it to generate two separate values as has been
done for other similar platforms.

---
 include/dt-bindings/pinctrl/k3.h | 3 +++
 1 file changed, 3 insertions(+)
include/dt-bindings/pinctrl/k3.h +0 -0
index 63e038e36c..a5204ab91d 100644

include/dt-bindings/pinctrl/k3.h line 47

Quoted 7 lines
include/dt-bindings/pinctrl/k3.h +3 -0
@@ -41,4 +41,7 @@
 #define J721S2_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
 #define J721S2_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
 
+#define AM62X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
 #endif

I assume this is being submitted to upstream linux as well?

Signature · 1 line
Tom
author maintainer
#4 lore raw

Re: [PATCH 02/11] dt-bindings: pinctrl: k3: Introduce pinmux definitions for AM62

Quoted 28 lines · Tom Rini
Quoted 27 lines · Vignesh Raghavendra

From: Suman Anna <[email protected]>

Add pinctrl macros for AM62x SoCs. These macro definitions are similar to that of previous platforms, but adding new definitions to avoid any naming confusions in the SoC dts files.

checkpatch insists the following error exists:
ERROR: Macros with complex values should be enclosed in parentheses

However, we do not need parentheses enclosing the values for this macro as we do intend it to generate two separate values as has been
done for other similar platforms.

---
 include/dt-bindings/pinctrl/k3.h | 3 +++
 1 file changed, 3 insertions(+)
include/dt-bindings/pinctrl/k3.h +0 -0
index 63e038e36c..a5204ab91d 100644
@@ -41,4 +41,7 @@
 #define J721S2_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
 #define J721S2_WKUP_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
 
Quoted 7 lines

include/dt-bindings/pinctrl/k3.h line 47

Quoted 4 lines
include/dt-bindings/pinctrl/k3.h +3 -0
+#define AM62X_IOPAD(pa, val, muxmode)		(((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62X_MCU_IOPAD(pa, val, muxmode)	(((pa) & 0x1fff)) ((val) | (muxmode))
+
 #endif

I assume this is being submitted to upstream linux as well?

Sorry, forgot to include upstream ref.:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/dt-bindings/pinctrl/k3.h#n44

author maintainer
#5 lore raw

PATCH 3/11 soc: ti: k3-socinfo: Add entry for AM62X SoC family

In reply to Vignesh Raghavendra

From: Suman Anna <[email protected]>

Add support for AM62x SoC identification.

---
 drivers/soc/soc_ti_k3.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/soc/soc_ti_k3.c +4 -0
index 965728e818..42344145f9 100644
@@ -15,6 +15,7 @@
 #define J7200			0xbb6d
 #define AM64X			0xbb38
 #define J721S2			0xbb75
+#define AM62X			0xbb7e
 
 #define JTAG_ID_VARIANT_SHIFT	28
 #define JTAG_ID_VARIANT_MASK	(0xf << 28)
@@ -49,6 +50,9 @@ static const char *get_family_string(u32 idreg)
 	case J721S2:
 		family = "J721S2";
 		break;
+	case AM62X:
+		family = "AM62X";
+		break;
 	default:
 		family = "Unknown Silicon";
 	};
Signature · 1 line
2.35.3
author maintainer
#7 lore raw

PATCH 4/11 arm: mach-k3: Introduce the basic files to support AM62

In reply to Vignesh Raghavendra

From: Suman Anna <[email protected]>

The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC architecture platform, providing ultra-low-power modes, dual display, multi-sensor edge compute, security and other BOM-saving integration. The AM62 SoC targets broad market to enable applications such as Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building Automation, Appliances and more.

Some highlights of this SoC are:

* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster. Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio, 1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only, enabling battery powered system design.

AM625 is the first device of the family. Add DT bindings for the same.

More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7

---
 arch/arm/mach-k3/Kconfig                      |   9 +-
 arch/arm/mach-k3/Makefile                     |   1 +
 arch/arm/mach-k3/am625_init.c                 | 254 ++++++++++++++++++
 arch/arm/mach-k3/arm64-mmu.c                  |   4 +-
 arch/arm/mach-k3/include/mach/am62_hardware.h |  66 +++++
 arch/arm/mach-k3/include/mach/am62_spl.h      |  44 +++
 arch/arm/mach-k3/include/mach/hardware.h      |   4 +
 arch/arm/mach-k3/include/mach/spl.h           |   5 +
 drivers/ram/Kconfig                           |   1 +
 9 files changed, 385 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm/mach-k3/am625_init.c
 create mode 100644 arch/arm/mach-k3/include/mach/am62_hardware.h
 create mode 100644 arch/arm/mach-k3/include/mach/am62_spl.h
arch/arm/mach-k3/Kconfig +8 -1
index a01bf23514..0dc4f44fdd 100644
@@ -16,6 +16,9 @@ config SOC_K3_J721S2
 config SOC_K3_AM642
 	bool "TI's K3 based AM642 SoC Family Support"
 
+config SOC_K3_AM625
+	bool "TI's K3 based AM625 SoC Family Support"
+
 endchoice
 
 config SYS_SOC
@@ -26,6 +29,7 @@ config SYS_K3_NON_SECURE_MSRAM_SIZE
 	default 0x80000 if SOC_K3_AM6
 	default 0x100000 if SOC_K3_J721E || SOC_K3_J721S2
 	default 0x1c0000 if SOC_K3_AM642
+	default 0x3c000 if SOC_K3_AM625
 	help
 	  Describes the total size of the MCU or OCMC MSRAM present on
 	  the SoC in use. This doesn't specify the total size of SPL as
@@ -37,6 +41,7 @@ config SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE
 	default 0x58000 if SOC_K3_AM6
 	default 0xc0000 if SOC_K3_J721E || SOC_K3_J721S2
 	default 0x180000 if SOC_K3_AM642
+	default 0x38000 if SOC_K3_AM625
 	help
 	  Describes the maximum size of the image that ROM can download
 	  from any boot media.
@@ -61,6 +66,7 @@ config SYS_K3_BOOT_PARAM_TABLE_INDEX
 	default 0x41cffbfc if SOC_K3_J721E
 	default 0x41cfdbfc if SOC_K3_J721S2
 	default 0x701bebfc if SOC_K3_AM642
+	default 0x43c3f290 if SOC_K3_AM625
 	help
 	  Address at which ROM stores the value which determines if SPL
 	  is booted up by primary boot media or secondary boot media.
@@ -129,6 +135,7 @@ config K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART
 config K3_SYSFW_IMAGE_SIZE_MAX
 	int "Amount of memory dynamically allocated for loading SYSFW blob"
 	depends on K3_LOAD_SYSFW
+	default 163840 if SOC_K3_AM625
 	default	278000
 	help
 	  Amount of memory (in bytes) reserved through dynamic allocation at
@@ -160,7 +167,7 @@ config K3_ATF_LOAD_ADDR
 
 config K3_DM_FW
 	bool "Separate DM firmware image"
-	depends on SPL && CPU_V7R && (SOC_K3_J721E || SOC_K3_J721S2) && !CLK_TI_SCI && !TI_SCI_POWER_DOMAIN
+	depends on SPL && CPU_V7R && (SOC_K3_J721E || SOC_K3_J721S2 || SOC_K3_AM625) && !CLK_TI_SCI && !TI_SCI_POWER_DOMAIN
 	default y
 	help
 	  Enabling this will indicate that the system has separate DM
arch/arm/mach-k3/Makefile +1 -0
index c0a6a9c87d..8459bef93b 100644
@@ -7,6 +7,7 @@ obj-$(CONFIG_SOC_K3_AM6) += am6_init.o
 obj-$(CONFIG_SOC_K3_J721E) += j721e_init.o j721e/ j7200/
 obj-$(CONFIG_SOC_K3_J721S2) += j721s2_init.o j721s2/
 obj-$(CONFIG_SOC_K3_AM642) += am642_init.o
+obj-$(CONFIG_SOC_K3_AM625) += am625_init.o am62x/
 obj-$(CONFIG_ARM64) += arm64-mmu.o
 obj-$(CONFIG_CPU_V7R) += r5_mpu.o lowlevel_init.o
 obj-$(CONFIG_TI_SECURE_DEVICE) += security.o
arch/arm/mach-k3/am625_init.c new file +254 -0

254 lines not on this page · raw message

arch/arm/mach-k3/arm64-mmu.c +2 -2
index 527e664318..12cb89335a 100644
@@ -222,7 +222,7 @@ struct mm_region *mem_map = j721s2_mem_map;
 
 #endif /* CONFIG_SOC_K3_J721S2 */
 
-#ifdef CONFIG_SOC_K3_AM642
+#if (CONFIG_IS_ENABLED(SOC_K3_AM642) || CONFIG_IS_ENABLED(SOC_K3_AM625))
 /* NR_DRAM_BANKS + 32bit IO + 64bit IO + terminator */
 #define NR_MMU_REGIONS	(CONFIG_NR_DRAM_BANKS + 3)
 
@@ -261,4 +261,4 @@ struct mm_region am64_mem_map[NR_MMU_REGIONS] = {
 };
 
 struct mm_region *mem_map = am64_mem_map;
-#endif /* CONFIG_SOC_K3_AM642 */
+#endif /* CONFIG_SOC_K3_AM642 || CONFIG_SOC_K3_AM625 */
arch/arm/mach-k3/include/mach/am62_hardware.h new file +66 -0

66 lines not on this page · raw message

arch/arm/mach-k3/include/mach/am62_spl.h new file +44 -0

44 lines not on this page · raw message

arch/arm/mach-k3/include/mach/hardware.h +4 -0
index 5c1265ffe9..7c6928d5da 100644
@@ -22,6 +22,10 @@
 #include "am64_hardware.h"
 #endif
 
+#ifdef CONFIG_SOC_K3_AM625
+#include "am62_hardware.h"
+#endif
+
 /* Assuming these addresses and definitions stay common across K3 devices */
 #define CTRLMMR_WKUP_JTAG_ID	0x43000014
 #define JTAG_ID_VARIANT_SHIFT	28
arch/arm/mach-k3/include/mach/spl.h +5 -0
index 8a61398529..17996f2938 100644
@@ -21,4 +21,9 @@
 #ifdef CONFIG_SOC_K3_AM642
 #include "am64_spl.h"
 #endif
+
+#ifdef CONFIG_SOC_K3_AM625
+#include "am62_spl.h"
+#endif
+
 #endif /* _ASM_ARCH_SPL_H_ */
drivers/ram/Kconfig +1 -0
index 709c916a2a..a4f9f1aad2 100644
@@ -64,6 +64,7 @@ choice
 
 	default K3_J721E_DDRSS if SOC_K3_J721E || SOC_K3_J721S2
 	default K3_AM64_DDRSS if SOC_K3_AM642
+	default K3_AM64_DDRSS if SOC_K3_AM625
 
 config K3_J721E_DDRSS
 	bool "Enable J721E DDRSS support"
Signature · 1 line
2.35.3
#8 lore raw

Re: [PATCH 04/11] arm: mach-k3: Introduce the basic files to support AM62

On Fri, Apr 15, 2022 at 07:39:24PM +0530, Vignesh Raghavendra wrote:

[snip]

Quoted 13 lines
arch/arm/mach-k3/am625_init.c new file +7 -0
new file mode 100644
index 0000000000..ee902a774e
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AM625: SoC specific initialization
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <[email protected]>
+ */

arch/arm/mach-k3/am625_init.c line 17

Quoted 10 lines
arch/arm/mach-k3/am625_init.c new file +10 -0
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
+#include "common.h"
+#include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>

Er, common.h twice? Please re-check this, and then also drop common.h (here and elsewhere) as it only includes other headers and we should avoid it when possible. In fact, checkpatch.pl complains about both dm.h and common.h so please address series-wide, thanks.

Signature · 1 line
Tom
author maintainer
#9 lore raw

Re: [PATCH 04/11] arm: mach-k3: Introduce the basic files to support AM62

Quoted 20 lines · Tom Rini

On Fri, Apr 15, 2022 at 07:39:24PM +0530, Vignesh Raghavendra wrote:

[snip]

Quoted 17 lines
arch/arm/mach-k3/am625_init.c new file +11 -0
new file mode 100644
index 0000000000..ee902a774e
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AM625: SoC specific initialization
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <[email protected]>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
Quoted 8 lines

arch/arm/mach-k3/am625_init.c line 17

Quoted 6 lines
arch/arm/mach-k3/am625_init.c new file +6 -0
+#include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
+#include "common.h"
+#include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>

Er, common.h twice?

Second one refers to arch/arm/mach-k3/common.h

Quoted 3 lines

Please re-check this, and then also drop common.h
(here and elsewhere) as it only includes other headers and we should avoid it when possible.

Sure, will do.

Quoted 3 lines

In fact, checkpatch.pl complains about both dm.h and common.h so please address series-wide, thanks.

Unfortunately, it doesn't ;(

Regards
Vignesh

#10 lore raw

Re: [PATCH 04/11] arm: mach-k3: Introduce the basic files to support AM62

Quoted 32 lines · Vignesh Raghavendra
Quoted 20 lines · Tom Rini

On Fri, Apr 15, 2022 at 07:39:24PM +0530, Vignesh Raghavendra wrote:

[snip]

Quoted 17 lines
arch/arm/mach-k3/am625_init.c new file +11 -0
new file mode 100644
index 0000000000..ee902a774e
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AM625: SoC specific initialization
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <[email protected]>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
Quoted 8 lines

arch/arm/mach-k3/am625_init.c line 17

Quoted 6 lines
arch/arm/mach-k3/am625_init.c new file +6 -0
+#include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
+#include "common.h"
+#include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>

Er, common.h twice?

Quoted 1 line

Second one refers to arch/arm/mach-k3/common.h

OK, lets rename that, and see what info there we can put elsewhere.

Quoted 11 lines
Quoted 3 lines

Please re-check this, and then also drop common.h
(here and elsewhere) as it only includes other headers and we should avoid it when possible.

Sure, will do.

Quoted 3 lines

In fact, checkpatch.pl complains about both dm.h and common.h so please address series-wide, thanks.

Unfortunately, it doesn't ;(

Ah, right. It only checks for inside of headers. But still should be avoided.

Signature · 1 line
Tom
author maintainer
#11 lore raw

Re: [PATCH 04/11] arm: mach-k3: Introduce the basic files to support AM62

Hi,

Quoted 33 lines · Tom Rini
Quoted 32 lines · Vignesh Raghavendra
Quoted 28 lines · Tom Rini

On Fri, Apr 15, 2022 at 07:39:24PM +0530, Vignesh Raghavendra wrote:

[snip]

Quoted 13 lines
arch/arm/mach-k3/am625_init.c new file +7 -0
new file mode 100644
index 0000000000..ee902a774e
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AM625: SoC specific initialization
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *	Suman Anna <[email protected]>
+ */

arch/arm/mach-k3/am625_init.c line 17

Quoted 10 lines
arch/arm/mach-k3/am625_init.c new file +10 -0
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
+#include "common.h"
+#include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>

Er, common.h twice?

Quoted 3 lines
Quoted 1 line

Second one refers to arch/arm/mach-k3/common.h

OK, lets rename that, and see what info there we can put elsewhere.

arch/arm/mach-k3/common.c which contains set of helper functions that are used across the K3 family of devices and this header exports those helpers (and is local to arch/arm/mach-k3/).

We may have split into multiple files according to functions in a separate series.

Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Please re-check this, and then also drop common.h
(here and elsewhere) as it only includes other headers and we should avoid it when possible.

Sure, will do.

Quoted 9 lines
Quoted 5 lines
Quoted 3 lines

In fact, checkpatch.pl complains about both dm.h and common.h so please address series-wide, thanks.

Unfortunately, it doesn't ;(

Ah, right. It only checks for inside of headers. But still should be avoided.

Yes, I will drop including <common.h> in next version.

Regards
Vignesh

author maintainer
#12 lore raw

PATCH 5/11 arm: mach-k3: am62: Introduce autogenerated SoC data

In reply to Vignesh Raghavendra

From: Suman Anna <[email protected]>

Introduce autogenerated SoC data support clk and device data for the AM62. Hook it upto to power-domain and clk frameworks of U-Boot.

---
 arch/arm/mach-k3/am62x/Makefile        |   6 +
 arch/arm/mach-k3/am62x/clk-data.c      | 366 +++++++++++++++++++++++++
 arch/arm/mach-k3/am62x/dev-data.c      |  78 ++++++
 drivers/clk/ti/clk-k3.c                |   6 +
 drivers/power/domain/ti-power-domain.c |   6 +
 include/k3-clk.h                       |   1 +
 include/k3-dev.h                       |   1 +
 7 files changed, 464 insertions(+)
 create mode 100644 arch/arm/mach-k3/am62x/Makefile
 create mode 100644 arch/arm/mach-k3/am62x/clk-data.c
 create mode 100644 arch/arm/mach-k3/am62x/dev-data.c
arch/arm/mach-k3/am62x/Makefile new file +6 -0
new file mode 100644
index 0000000000..d6c876df66
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier:	GPL-2.0+
+#
+# Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+
+obj-y += clk-data.o
+obj-y += dev-data.o
arch/arm/mach-k3/am62x/clk-data.c new file +366 -0

366 lines not on this page · raw message

arch/arm/mach-k3/am62x/dev-data.c new file +78 -0

78 lines not on this page · raw message

drivers/clk/ti/clk-k3.c +6 -0
index 74beb4d8eb..0dd65934b3 100644
@@ -73,6 +73,12 @@ static const struct soc_attr ti_k3_soc_clk_data[] = {
 		.family = "J721S2",
 		.data = &j721s2_clk_platdata,
 	},
+#endif
+#ifdef CONFIG_SOC_K3_AM625
+	{
+		.family = "AM62X",
+		.data = &am62x_clk_platdata,
+	},
 #endif
 	{ /* sentinel */ }
 };
drivers/power/domain/ti-power-domain.c +6 -0
index 752e76b399..4b8a319307 100644
@@ -86,6 +86,12 @@ static const struct soc_attr ti_k3_soc_pd_data[] = {
 		.family = "J721S2",
 		.data = &j721s2_pd_platdata,
 	},
+#endif
+#ifdef CONFIG_SOC_K3_AM625
+	{
+		.family = "AM62X",
+		.data = &am62x_pd_platdata,
+	},
 #endif
 	{ /* sentinel */ }
 };
include/k3-clk.h +1 -0
index 31292b59f2..371f077c44 100644
@@ -174,6 +174,7 @@ struct ti_k3_clk_platdata {
 extern const struct ti_k3_clk_platdata j721e_clk_platdata;
 extern const struct ti_k3_clk_platdata j7200_clk_platdata;
 extern const struct ti_k3_clk_platdata j721s2_clk_platdata;
+extern const struct ti_k3_clk_platdata am62x_clk_platdata;
 
 struct clk *clk_register_ti_pll(const char *name, const char *parent_name,
 				void __iomem *reg);
include/k3-dev.h +1 -0
index b46b8c3aab..87e873b9ce 100644
@@ -78,6 +78,7 @@ struct ti_k3_pd_platdata {
 extern const struct ti_k3_pd_platdata j721e_pd_platdata;
 extern const struct ti_k3_pd_platdata j7200_pd_platdata;
 extern const struct ti_k3_pd_platdata j721s2_pd_platdata;
+extern const struct ti_k3_pd_platdata am62x_pd_platdata;
 
 u8 ti_pd_state(struct ti_pd *pd);
 u8 lpsc_get_state(struct ti_lpsc *lpsc);
Signature · 1 line
2.35.3
author maintainer
#13 lore raw

PATCH 6/11 dma: ti: Add PSIL data for AM62x DMASS

In reply to Vignesh Raghavendra

Add PSIL data for AM62x SoC

---
 drivers/dma/ti/Makefile       |  1 +
 drivers/dma/ti/k3-psil-am62.c | 50 +++++++++++++++++++++++++++++++++++
 drivers/dma/ti/k3-psil-priv.h |  1 +
 drivers/dma/ti/k3-psil.c      |  2 ++
 4 files changed, 54 insertions(+)
 create mode 100644 drivers/dma/ti/k3-psil-am62.c
drivers/dma/ti/Makefile +1 -0
index 6a4f4f1365..56f348700d 100644
@@ -7,3 +7,4 @@ k3-psil-data-$(CONFIG_SOC_K3_AM6) += k3-psil-am654.o
 k3-psil-data-$(CONFIG_SOC_K3_J721E) += k3-psil-j721e.o
 k3-psil-data-$(CONFIG_SOC_K3_J721S2) += k3-psil-j721s2.o
 k3-psil-data-$(CONFIG_SOC_K3_AM642) += k3-psil-am64.o
+k3-psil-data-$(CONFIG_SOC_K3_AM625) += k3-psil-am62.o
drivers/dma/ti/k3-psil-am62.c new file +50 -0

50 lines not on this page · raw message

drivers/dma/ti/k3-psil-priv.h +1 -0
index 77acaf2139..28078c6bd8 100644
@@ -41,5 +41,6 @@ extern struct psil_ep_map am654_ep_map;
 extern struct psil_ep_map j721e_ep_map;
 extern struct psil_ep_map j721s2_ep_map;
 extern struct psil_ep_map am64_ep_map;
+extern struct psil_ep_map am62_ep_map;
 
 #endif /* K3_PSIL_PRIV_H_ */
drivers/dma/ti/k3-psil.c +2 -0
index 8b2129d4f5..f1330bf4b0 100644
@@ -24,6 +24,8 @@ struct psil_endpoint_config *psil_get_ep_config(u32 thread_id)
 			soc_ep_map = &j721s2_ep_map;
 		else if (IS_ENABLED(CONFIG_SOC_K3_AM642))
 			soc_ep_map = &am64_ep_map;
+		else if (IS_ENABLED(CONFIG_SOC_K3_AM625))
+			soc_ep_map = &am62_ep_map;
 	}
 
 	if (thread_id & K3_PSIL_DST_THREAD_ID_OFFSET && soc_ep_map->dst) {
Signature · 1 line
2.35.3
author maintainer
#14 lore raw

PATCH 7/11 arm: dts: Introduce base AM62 SoC dtsi files

In reply to Vignesh Raghavendra

From: Suman Anna <[email protected]>

Introduce the basic AM62 SoC description dtsi files. While doing this, lets reuse the DDR controller definition from AM64 as the instance is the same

---
 arch/arm/dts/k3-am62-ddr.dtsi    |  11 +
 arch/arm/dts/k3-am62-main.dtsi   | 503 +++++++++++++++++++++++++++++++
 arch/arm/dts/k3-am62-mcu.dtsi    |  36 +++
 arch/arm/dts/k3-am62-wakeup.dtsi |  41 +++
 arch/arm/dts/k3-am62.dtsi        | 105 +++++++
 arch/arm/dts/k3-am625.dtsi       | 103 +++++++
 6 files changed, 799 insertions(+)
 create mode 100644 arch/arm/dts/k3-am62-ddr.dtsi
 create mode 100644 arch/arm/dts/k3-am62-main.dtsi
 create mode 100644 arch/arm/dts/k3-am62-mcu.dtsi
 create mode 100644 arch/arm/dts/k3-am62-wakeup.dtsi
 create mode 100644 arch/arm/dts/k3-am62.dtsi
 create mode 100644 arch/arm/dts/k3-am625.dtsi
arch/arm/dts/k3-am62-ddr.dtsi new file +11 -0
new file mode 100644
index 0000000000..0a8ced8f38
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include "k3-am64-ddr.dtsi"
+&memorycontroller {
+	power-domains = <&k3_pds 170 TI_SCI_PD_SHARED>,
+			<&k3_pds 55 TI_SCI_PD_SHARED>;
+	clocks = <&k3_clks 170 0>, <&k3_clks 16 4>;
+};
arch/arm/dts/k3-am62-main.dtsi new file +503 -0

503 lines not on this page · raw message

arch/arm/dts/k3-am62-mcu.dtsi new file +36 -0
new file mode 100644
index 0000000000..9d210d55fc
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM625 SoC Family MCU Domain peripherals
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_mcu {
+	mcu_pmx0: pinctrl@4084000 {
+		compatible = "pinctrl-single";
+		reg = <0x00 0x04084000 0x00 0x88>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	mcu_uart0: serial@4a00000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x04a00000 0x00 0x100>;
+		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 149 0>;
+		clock-names = "fclk";
+	};
+
+	mcu_i2c0: i2c@4900000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x04900000 0x00 0x100>;
+		interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 106 2>;
+		clock-names = "fck";
+	};
+};
arch/arm/dts/k3-am62-wakeup.dtsi new file +41 -0

41 lines not on this page · raw message

arch/arm/dts/k3-am62.dtsi new file +105 -0

105 lines not on this page · raw message

arch/arm/dts/k3-am625.dtsi new file +103 -0

103 lines not on this page · raw message

Signature · 1 line
2.35.3
#15 lore raw

Re: [PATCH 07/11] arm: dts: Introduce base AM62 SoC dtsi files

Quoted 9 lines · Vignesh Raghavendra

From: Suman Anna <[email protected]>

Introduce the basic AM62 SoC description dtsi files. While doing this, lets reuse the DDR controller definition from AM64 as the instance is the same

Quoted 8 lines
---
 arch/arm/dts/k3-am62-ddr.dtsi    |  11 +
 arch/arm/dts/k3-am62-main.dtsi   | 503 +++++++++++++++++++++++++++++++
 arch/arm/dts/k3-am62-mcu.dtsi    |  36 +++
 arch/arm/dts/k3-am62-wakeup.dtsi |  41 +++
 arch/arm/dts/k3-am62.dtsi        | 105 +++++++
 arch/arm/dts/k3-am625.dtsi       | 103 +++++++
 6 files changed, 799 insertions(+)

Since the commit doesn't say, what is the status of this with upstream Linux kernel? Thanks.

Signature · 1 line
Tom
author maintainer
#16 lore raw

Re: [PATCH 07/11] arm: dts: Introduce base AM62 SoC dtsi files

Quoted 19 lines · Tom Rini
Quoted 9 lines · Vignesh Raghavendra

From: Suman Anna <[email protected]>

Introduce the basic AM62 SoC description dtsi files. While doing this, lets reuse the DDR controller definition from AM64 as the instance is the same

Quoted 8 lines
---
 arch/arm/dts/k3-am62-ddr.dtsi    |  11 +
 arch/arm/dts/k3-am62-main.dtsi   | 503 +++++++++++++++++++++++++++++++
 arch/arm/dts/k3-am62-mcu.dtsi    |  36 +++
 arch/arm/dts/k3-am62-wakeup.dtsi |  41 +++
 arch/arm/dts/k3-am62.dtsi        | 105 +++++++
 arch/arm/dts/k3-am625.dtsi       | 103 +++++++
 6 files changed, 799 insertions(+)
Quoted 3 lines

Since the commit doesn't say, what is the status of this with upstream Linux kernel? Thanks.

Base dts with UART support is upstream[1]. Rest of peripherals are under review [2]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/ti/k3-am625-sk.dts
[2] https://lore.kernel.org/linux-arm-kernel/[email protected]/T/#t

author maintainer
#17 lore raw

PATCH 8/11 board: ti: Introduce the basic files to support AM62 SK board

In reply to Vignesh Raghavendra

From: Suman Anna <[email protected]>

Add basic support for AM64 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from BSS and does not step on BSS section

---
 arch/arm/mach-k3/Kconfig              |   1 +
 board/ti/am62x/Kconfig                |  63 +++++++++++
 board/ti/am62x/Makefile               |   8 ++
 board/ti/am62x/evm.c                  | 149 ++++++++++++++++++++++++++
 drivers/firmware/ti_sci_static_data.h |   7 ++
 5 files changed, 228 insertions(+)
 create mode 100644 board/ti/am62x/Kconfig
 create mode 100644 board/ti/am62x/Makefile
 create mode 100644 board/ti/am62x/evm.c
arch/arm/mach-k3/Kconfig +1 -0
index 0dc4f44fdd..57f693e9a1 100644
@@ -178,6 +178,7 @@ config K3_DM_FW
 
 source "board/ti/am65x/Kconfig"
 source "board/ti/am64x/Kconfig"
+source "board/ti/am62x/Kconfig"
 source "board/ti/j721e/Kconfig"
 source "board/siemens/iot2050/Kconfig"
 source "board/ti/j721s2/Kconfig"
board/ti/am62x/Kconfig new file +63 -0

63 lines not on this page · raw message

board/ti/am62x/Makefile new file +8 -0
new file mode 100644
index 0000000000..f4c35edffa
@@ -0,0 +1,8 @@
+#
+# Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+#	Suman Anna <[email protected]>
+#
+# SPDX-License-Identifier:     GPL-2.0+
+#
+
+obj-y	+= evm.o
board/ti/am62x/evm.c new file +149 -0

149 lines not on this page · raw message

drivers/firmware/ti_sci_static_data.h +7 -0
index e6a3b66c03..21e783cc45 100644
@@ -118,6 +118,13 @@ static struct ti_sci_resource_static_data rm_static_data[] = {
 };
 #endif /* CONFIG_TARGET_J721S2_R5_EVM */
 
+#if IS_ENABLED(CONFIG_TARGET_AM625_R5_EVM)
+static struct ti_sci_resource_static_data rm_static_data[] = {
+	{ },
+};
+
+#endif /* CONFIG_TARGET_AM625_R5_EVM */
+
 #else
 static struct ti_sci_resource_static_data rm_static_data[] = {
 	{ },
Signature · 1 line
2.35.3
author maintainer
#18 lore raw

PATCH 9/11 arm: dts: Add support for AM62-SK

In reply to Vignesh Raghavendra

From: Nishanth Menon <[email protected]>

AM62 StarterKit (SK) board is a low cost, small form factor board designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header

Add basic support for AM62-SK.

Schematics: https://www.ti.com/lit/zip/sprr448

---
 arch/arm/dts/Makefile                      |    3 +
 arch/arm/dts/k3-am62-main.dtsi             |   44 +-
 arch/arm/dts/k3-am62-mcu.dtsi              |   20 +
 arch/arm/dts/k3-am625-r5-sk.dts            |  130 ++
 arch/arm/dts/k3-am625-sk-u-boot.dtsi       |  124 ++
 arch/arm/dts/k3-am625-sk.dts               |  469 +++++
 arch/arm/dts/k3-am62x-sk-ddr4-1600MTs.dtsi | 2189 ++++++++++++++++++++
 7 files changed, 2972 insertions(+), 7 deletions(-)
 create mode 100644 arch/arm/dts/k3-am625-r5-sk.dts
 create mode 100644 arch/arm/dts/k3-am625-sk-u-boot.dtsi
 create mode 100644 arch/arm/dts/k3-am625-sk.dts
 create mode 100644 arch/arm/dts/k3-am62x-sk-ddr4-1600MTs.dtsi
arch/arm/dts/Makefile +3 -0
index df7b4addf9..fdfdefc5e4 100644
@@ -1162,6 +1162,9 @@ dtb-$(CONFIG_SOC_K3_AM642) += k3-am642-evm.dtb \
 			      k3-am642-sk.dtb \
 			      k3-am642-r5-sk.dtb
 
+dtb-$(CONFIG_SOC_K3_AM625) += k3-am625-sk.dtb \
+			      k3-am625-r5-sk.dtb
+
 dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt7622-rfb.dtb \
 	mt7623a-unielec-u7623-02-emmc.dtb \
arch/arm/dts/k3-am62-main.dtsi +37 -7

87 lines not on this page · raw message

arch/arm/dts/k3-am62-mcu.dtsi +20 -0
index 9d210d55fc..d103824c96 100644
@@ -33,4 +33,24 @@
 		clocks = <&k3_clks 106 2>;
 		clock-names = "fck";
 	};
+
+	mcu_spi0: spi@4b00000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x04b00000 0x00 0x400>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 147 0>;
+	};
+
+	mcu_spi1: spi@4b10000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x04b10000 0x00 0x400>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 148 0>;
+	};
 };
arch/arm/dts/k3-am625-r5-sk.dts new file +130 -0

130 lines not on this page · raw message

arch/arm/dts/k3-am625-sk-u-boot.dtsi new file +124 -0

124 lines not on this page · raw message

arch/arm/dts/k3-am625-sk.dts new file +469 -0

469 lines not on this page · raw message

arch/arm/dts/k3-am62x-sk-ddr4-1600MTs.dtsi new file +2189 -0

2,157 lines not on this page · raw message

The rest of this diff is not shown. View the raw message.

Signature · 1 line
2.35.3

Part of the diff is not shown here. View the raw message.

author maintainer
#19 lore raw

PATCH 10/11 configs: Add configs for AM62x SK

In reply to Vignesh Raghavendra

Add am62x_evm_r5_defconfig for R5 SPL and am62x_evm_a53_defconfig for A53 SPL and U-Boot support.

---
 board/ti/am62x/MAINTAINERS      |   8 +++
 configs/am62x_evm_a53_defconfig | 110 ++++++++++++++++++++++++++++++
 configs/am62x_evm_r5_defconfig  | 114 ++++++++++++++++++++++++++++++++
 include/configs/am62x_evm.h     | 106 +++++++++++++++++++++++++++++
 4 files changed, 338 insertions(+)
 create mode 100644 board/ti/am62x/MAINTAINERS
 create mode 100644 configs/am62x_evm_a53_defconfig
 create mode 100644 configs/am62x_evm_r5_defconfig
 create mode 100644 include/configs/am62x_evm.h
board/ti/am62x/MAINTAINERS new file +8 -0
new file mode 100644
index 0000000000..8942876cba
@@ -0,0 +1,8 @@
+AM64x BOARD
+M:	Dave Gerlach <[email protected]>
+M:	Tom Rini <[email protected]>
+S:	Maintained
+F:	board/ti/am62x/
+F:	include/configs/am62x_evm.h
+F:	configs/am62x_evm_r5_defconfig
+F:	configs/am62x_evm_a53_defconfig
configs/am62x_evm_a53_defconfig new file +110 -0

110 lines not on this page · raw message

configs/am62x_evm_r5_defconfig new file +114 -0

114 lines not on this page · raw message

include/configs/am62x_evm.h new file +106 -0

106 lines not on this page · raw message

Signature · 1 line
2.35.3
author maintainer
#20 lore raw

PATCH 11/11 doc: ti: Add readme for AM62x SK

In reply to Vignesh Raghavendra

Add info of boot flow and build steps for AM62x SK.

---
 doc/board/ti/am62x_sk.rst | 231 ++++++++++++++++++++++++++++++++++++++
 doc/board/ti/index.rst    |   1 +
 2 files changed, 232 insertions(+)
 create mode 100644 doc/board/ti/am62x_sk.rst
doc/board/ti/am62x_sk.rst new file +231 -0
new file mode 100644
index 0000000000..4e68c2018a
@@ -0,0 +1,231 @@
+.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+.. sectionauthor:: Vignesh Raghavendra <[email protected]>
+
+Texas Instruments AM62 Platforms
+================================
+
+Introduction:
+-------------
+The AM62 SoC family is the follow on AM335x built on the K3 Multicore
+SoC architecture platform, providing ultra-low-power modes, dual
+display, multi-sensor edge compute, security and other BOM-saving
+integrations.  The AM62 SoC targets a broad market to enable
+applications such as Industrial HMI, PLC/CNC/Robot control, Medical
+Equipment, Building Automation, Appliances and more.
+
+Some highlights of this SoC are:
+
+* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
+  Pin-to-pin compatible options for single and quad core are available.
+* Cortex-M4F for general-purpose or safety usage.
+* Dual display support, providing 24-bit RBG parallel interface and
+  OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
+  resolution.
+* Selectable GPU support, up to 8GFLOPS, providing better user experience
+  in 3D graphic display case and Android.
+* PRU(Programmable Realtime Unit) support for customized programmable
+  interfaces/IOs.
+* Integrated Giga-bit Ethernet switch supporting up to a total of two
+  external ports (TSN capable).
+* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
+  NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
+  1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
+* Dedicated Centralized System Controller for Security, Power, and
+  Resource Management.
+* Multiple low power modes support, ex: Deep sleep, Standby, MCU-only,
+  enabling battery powered system design.
+
+More details can be found in the Technical Reference Manual:
+https://www.ti.com/lit/pdf/spruiv7
+
+Boot Flow:
+----------
+Below is the pictorial representation of boot flow:
+
+.. code-block:: text
+
+ +------------------------------------------------------------------------+
+ |        TIFS            |      Main R5          |        A53            |
+ +------------------------------------------------------------------------+
+ |    +--------+          |                       |                       |
+ |    |  Reset |          |                       |                       |
+ |    +--------+          |                       |                       |
+ |         :              |                       |                       |
+ |    +--------+          |   +-----------+       |                       |
+ |    | *ROM*  |----------|-->| Reset rls |       |                       |
+ |    +--------+          |   +-----------+       |                       |
+ |    |        |          |         :             |                       |
+ |    |  ROM   |          |         :             |                       |
+ |    |services|          |         :             |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |   |  *R5 ROM*   |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |<---------|---|Load and auth|     |                       |
+ |    |        |          |   | tiboot3.bin |     |                       |
+ |    +--------+          |   +-------------+     |                       |
+ |    |        |<---------|---| Load sysfw  |     |                       |
+ |    |        |          |   | part to TIFS|     |                       |
+ |    |        |          |   | core        |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |         :             |                       |
+ |    |        |          |         :             |                       |
+ |    |        |          |         :             |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |   |  *R5 SPL*   |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |   |    DDR      |     |                       |
+ |    |        |          |   |   config    |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |   |    Load     |     |                       |
+ |    |        |          |   |  tispl.bin  |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |   |   Load R5   |     |                       |
+ |    |        |          |   |   firmware  |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |<---------|---| Start A53   |     |                       |
+ |    |        |          |   | and jump to |     |                       |
+ |    |        |          |   | DM fw image |     |                       |
+ |    |        |          |   +-------------+     |                       |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |----------|-----------------------|---->| Reset rls |     |
+ |    |        |          |                       |     +-----------+     |
+ |    |  TIFS  |          |                       |          :            |
+ |    |Services|          |                       |     +-----------+     |
+ |    |        |<---------|-----------------------|---->|*ATF/OPTEE*|     |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |          |                       |          :            |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |<---------|-----------------------|---->| *A53 SPL* |     |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |          |                       |     |   Load    |     |
+ |    |        |          |                       |     | u-boot.img|     |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |          |                       |          :            |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |<---------|-----------------------|---->| *U-Boot*  |     |
+ |    |        |          |                       |     +-----------+     |
+ |    |        |          |                       |     |  prompt   |     |
+ |    |        |----------|-----------------------|-----+-----------+-----|
+ |    +--------+          |                       |                       |
+ |                        |                       |                       |
+ +------------------------------------------------------------------------+
+
+- Here TIFS acts as master and provides all the critical services. R5/A53
+  requests TIFS to get these services done as shown in the above diagram.
+
+Sources:
+--------
+1. SYSFW:
+	Tree: git://git.ti.com/k3-image-gen/k3-image-gen.git
+	Branch: master
+
+2. ATF:
+	Tree: https://github.com/ARM-software/arm-trusted-firmware.git
+	Branch: master
+
+3. OPTEE:
+	Tree: https://github.com/OP-TEE/optee_os.git
+	Branch: master
+
+4. U-Boot:
+	Tree: https://source.denx.de/u-boot/u-boot
+	Branch: master
+
+5. TI Linux Firmware:
+	Tree: git://git.ti.com/processor-firmware/ti-linux-firmware.git
+	Branch: ti-linux-firmware
+
+Build procedure:
+----------------
+1. ATF:
+
+.. code-block:: text
+
+ $ make CROSS_COMPILE=aarch64-none-linux-gnu- ARCH=aarch64 PLAT=k3 TARGET_BOARD=lite SPD=opteed
+
+2. OPTEE:
+
+.. code-block:: text
+
+ $ make PLATFORM=k3 CFG_ARM64_core=y CROSS_COMPILE=arm-none-linux-gnueabihf- CROSS_COMPILE64=aarch64-none-linux-gnu-
+
+3. U-Boot:
+
+* 3.1 R5:
+
+.. code-block:: text
+
+ $ make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabihf- am62x_evm_r5_defconfig O=/tmp/r5
+ $ make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabihf- O=/tmp/r5
+ $ cd <k3-image-gen>
+ $ make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabihf- SOC=am62x SBL=/tmp/r5/spl/u-boot-spl.bin SYSFW_PATH=<path to ti-linux-firmware>/ti-sysfw/ti-fs-firmware-am62x-gp.bin
+
+Use the tiboot3.bin generated from last command
+
+* 3.2 A53:
+
+.. code-block:: text
+
+ $ make ARCH=arm CROSS_COMPILE=aarch64-none-linux-gnu- am62x_evm_a53_defconfig O=/tmp/a53
+ $ make ARCH=arm CROSS_COMPILE=aarch64-none-linux-gnu- ATF=<path to ATF dir>/build/k3/lite/release/bl31.bin TEE=<path to OPTEE OS dir>/out/arm-plat-k3/core/tee-pager_v2.bin DM=<path to ti-linux-firmware>/ti-dm/am62xx/ipc_echo_testb_mcu1_0_release_strip.xer5f O=/tmp/a53
+
+Target Images
+--------------
+Copy the below images to an SD card and boot:
+ - tiboot3.bin from step 3.1
+ - tispl.bin, u-boot.img from 3.2
+
+Image formats:
+--------------
+
+- tiboot3.bin:
+
+.. code-block:: text
+
+                +-----------------------+
+                |        X.509          |
+                |      Certificate      |
+                | +-------------------+ |
+                | |                   | |
+                | |        R5         | |
+                | |   u-boot-spl.bin  | |
+                | |                   | |
+                | +-------------------+ |
+                | |                   | |
+                | |TIFS with board cfg| |
+                | |                   | |
+                | +-------------------+ |
+                | |                   | |
+                | |                   | |
+                | |     FIT header    | |
+                | | +---------------+ | |
+                | | |               | | |
+                | | |   DTB 1...N   | | |
+                | | +---------------+ | |
+                | +-------------------+ |
+                +-----------------------+
+
+- tispl.bin
+
+.. code-block:: text
+
+                +-----------------------+
+                |                       |
+                |       FIT HEADER      |
+                | +-------------------+ |
+                | |                   | |
+                | |      A53 ATF      | |
+                | +-------------------+ |
+                | |                   | |
+                | |     A53 OPTEE     | |
+                | +-------------------+ |
+                | |                   | |
+                | |      R5 DM FW     | |
+                | +-------------------+ |
+                | |                   | |
+                | |      A53 SPL      | |
+                | +-------------------+ |
+                | |                   | |
+                | |   SPL DTB 1...N   | |
+                | +-------------------+ |
+                +-----------------------+
doc/board/ti/index.rst +1 -0
index 014a097178..250d9242e8 100644
@@ -8,3 +8,4 @@ Texas Instruments
 
    am335x_evm
    j721e_evm
+   am62x_sk
Signature · 1 line
2.35.3
#22 lore raw

Re: [PATCH 11/11] doc: ti: Add readme for AM62x SK

In reply to Vignesh Raghavendra
Quoted 5 lines · Vignesh Raghavendra

Add info of boot flow and build steps for AM62x SK.

---
  doc/board/ti/am62x_sk.rst | 231 ++++++++++++++++++++++++++++++++++++++

This isn't specific to the SK, more the AM62x in general, suggest name am62x.rst.

[...]

doc/board/ti/am62x_sk.rst line 145

Quoted 8 lines
doc/board/ti/am62x_sk.rst new file +8 -0
+Build procedure:
+----------------
+1. ATF:
+
+.. code-block:: text
+
+ $ make CROSS_COMPILE=aarch64-none-linux-gnu- ARCH=aarch64 PLAT=k3 TARGET_BOARD=lite SPD=opteed
+

These compiler names might not be the same as installed by some current package managers (-none), maybe we start by setting up two env vars to point to the two compilers we use:

export CROSS_COMPILE32=arm-none-linux-gnueabihf-
export CROSS_COMPILE64=aarch64-none-linux-gnu-

Then just use those below, that way we only have to switch these first two commands if we have a different compiler.

CROSS_COMPILE=$CROSS_COMPILE32

etc..

doc/board/ti/am62x_sk.rst line 158

Quoted 13 lines

+2. OPTEE:

doc/board/ti/am62x_sk.rst new file +12 -0
+
+.. code-block:: text
+
+ $ make PLATFORM=k3 CFG_ARM64_core=y CROSS_COMPILE=arm-none-linux-gnueabihf- CROSS_COMPILE64=aarch64-none-linux-gnu-
+
+3. U-Boot:
+
+* 3.1 R5:
+
+.. code-block:: text
+
+ $ make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabihf- am62x_evm_r5_defconfig O=/tmp/r5

Lets not pollute directories outside of the current one, suggest O=build/r5 and the same below.

Andrew

author maintainer
#23 lore raw

Re: [PATCH 11/11] doc: ti: Add readme for AM62x SK

Quoted 11 lines · Andrew Davis
Quoted 5 lines · Vignesh Raghavendra

Add info of boot flow and build steps for AM62x SK.

---
  doc/board/ti/am62x_sk.rst | 231 ++++++++++++++++++++++++++++++++++++++

This isn't specific to the SK, more the AM62x in general, suggest name am62x.rst.

Agreed

Quoted 19 lines

[...]

Quoted 9 lines
doc/board/ti/am62x_sk.rst new file +7 -0
+Build procedure:
+----------------
+1. ATF:
+
+.. code-block:: text
+
+ $ make CROSS_COMPILE=aarch64-none-linux-gnu- ARCH=aarch64 PLAT=k3

TARGET_BOARD=lite SPD=opteed
+

These compiler names might not be the same as installed by some current package managers (-none),
maybe we start by setting up two env vars to point to the two compilers we use:

Quoted 9 lines

export CROSS_COMPILE32=arm-none-linux-gnueabihf-
export CROSS_COMPILE64=aarch64-none-linux-gnu-

Then just use those below, that way we only have to switch these first two commands if we
have a different compiler.

CROSS_COMPILE=$CROSS_COMPILE32

Good idea, thanks!

Quoted 16 lines

etc..

Quoted 13 lines

+2. OPTEE:

doc/board/ti/am62x_sk.rst new file +4 -0
+
+.. code-block:: text
+
+ $ make PLATFORM=k3 CFG_ARM64_core=y

CROSS_COMPILE=arm-none-linux-gnueabihf-
CROSS_COMPILE64=aarch64-none-linux-gnu-

doc/board/ti/am62x_sk.rst new file +6 -0
+
+3. U-Boot:
+
+* 3.1 R5:
+
+.. code-block:: text
Quoted 8 lines
Quoted 3 lines

+
+ $ make ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabihf- am62x_evm_r5_defconfig O=/tmp/r5

Lets not pollute directories outside of the current one, suggest O=build/r5
and the same below.

Sure, will fix!

Regards
Vignesh