RK3568 PCIe V3 support
Subsystems (4)
v3 cover RK3568 PCIe V3 support
From: Frank Wunderlich <[email protected]>
This series adds Rockchip PCIe V3 support found on rk3568 SOC.
It is based on "Enable rk356x PCIe controller" series of Peter Geis
v9: https://patchwork.kernel.org/project/linux-rockchip/list/?series=636944
Compared to PCIeV2 which uses the Naneng combphy, PCIe v3 uses a dedicated PCI-phy.
New in this version is that lane-map is no separate patch and moved from PCIe- to phy-driver.
Peter has tested m2-slot too and so the bifurcation.
The Phy-Patch is now changed to original author, but our changes are squashed in.
Frank Wunderlich (4):
dt-bindings: phy: rockchip: add PCIe v3 phy
dt-bindings: soc: grf: add pcie30-{phy,pipe}-grf
arm64: dts: rockchip: rk3568: Add PCIe v3 nodes
arm64: dts: rockchip: Add PCIe v3 nodes to BPI-R2-Pro
Shawn Lin (1):
phy: rockchip: Support PCIe v3
.../bindings/phy/rockchip,pcie3-phy.yaml | 82 +++++ .../devicetree/bindings/soc/rockchip/grf.yaml | 3 + .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts | 90 +++++ arch/arm64/boot/dts/rockchip/rk3568.dtsi | 122 +++++++ drivers/phy/rockchip/Kconfig | 9 + drivers/phy/rockchip/Makefile | 1 + .../phy/rockchip/phy-rockchip-snps-pcie3.c | 317 ++++++++++++++++++ include/linux/phy/pcie.h | 12 + 8 files changed, 636 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml create mode 100644 drivers/phy/rockchip/phy-rockchip-snps-pcie3.c create mode 100644 include/linux/phy/pcie.h
Signature · 1 line
2.25.1
RFC v3 1/5 dt-bindings: phy: rockchip: add PCIe v3 phy
From: Frank Wunderlich <[email protected]>
Add a new binding file for Rockchip PCIe v3 phy driver.
---
v3:
- drop quotes
- drop rk3588
- make clockcount fixed to 3
- full path for binding header file
- drop phy-mode and its header and add lane-map
v2:
dt-bindings: rename yaml for PCIe v3 rockchip-pcie3-phy.yaml => rockchip,pcie3-phy.yaml
changes in pcie3 phy yaml
- change clock names to ordered const list
- extend pcie30-phymode description
- add phy-cells to required properties
- drop unevaluatedProperties
- example with 1 clock each line
- use default property instead of text describing it
- update license
--- .../bindings/phy/rockchip,pcie3-phy.yaml | 82 +++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml new file +82 -0
@@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip,pcie3-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip PCIe v3 phy + +maintainers: + - Heiko Stuebner <[email protected]> + +properties: + compatible: + enum: + - rockchip,rk3568-pcie3-phy + + reg: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + items: + - const: refclk_m + - const: refclk_n + - const: pclk + + minItems: 3 + + lane-map: + description: which lanes (by position) should be mapped to which + controller (value). 0 means lane unused, higher value means used. + (controller-number +1 ) + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 16 + items: + minimum: 0 + maximum: 16 + + "#phy-cells": + const: 0 + + resets: + maxItems: 1 + + reset-names: + const: phy + + rockchip,phy-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the syscon managing the phy "general register files" + + rockchip,pipe-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the syscon managing the pipe "general register files" + +required: + - compatible + - reg + - rockchip,phy-grf + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + pcie30phy: phy@fe8c0000 { + compatible = "rockchip,rk3568-pcie3-phy"; + reg = <0x0 0xfe8c0000 0x0 0x20000>; + #phy-cells = <0>; + clocks = <&pmucru CLK_PCIE30PHY_REF_M>, + <&pmucru CLK_PCIE30PHY_REF_N>, + <&cru PCLK_PCIE30PHY>; + clock-names = "refclk_m", "refclk_n", "pclk"; + resets = <&cru SRST_PCIE30PHY>; + reset-names = "phy"; + rockchip,phy-grf = <&pcie30_phy_grf>; + };
Signature · 1 line
2.25.1
RFC v3 2/5 dt-bindings: soc: grf: add pcie30-{phy,pipe}-grf
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add compatibles for PCIe v3 General Register Files.
---
v3:
- fix order of grf-bindings
v2:
- add soc-part to pcie3-phy-grf
--- Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 3 +++ 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/soc/rockchip/grf.yaml +3 -0
@@ -16,7 +16,10 @@ properties: - enum: - rockchip,rk3288-sgrf - rockchip,rk3566-pipe-grf + - rockchip,rk3568-pcie3-phy-grf - rockchip,rk3568-usb2phy-grf + - rockchip,rk3588-pcie3-phy-grf + - rockchip,rk3588-pcie3-pipe-grf - rockchip,rv1108-usbgrf - const: syscon - items:
Signature · 1 line
2.25.1
RFC v3 3/5 phy: rockchip: Support PCIe v3
In reply to Frank WunderlichFrom: Shawn Lin <[email protected]>
RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566. It use a dedicated PCIe-phy. Add support for this.
Initial support by Shawn Lin, modifications by Peter Geis and Frank Wunderlich.
Add lane-map support for splitting pcie-lanes across controllers.
The lane-map is an array where x=0 means lane is disabled and x > 0 means controller x is assigned to phy lane.
---
v3:
- change dt-binding include
- change reset to devm_reset_control_get_optional_exclusive exit on error and lower severity of message if unset
- fix from peter: disable reg-write for phy-mode in rockchip_p3phy_probe
- move bifurcation/lane-map support from PCIe to phy driver
v2:
- move dt-bindings header into separate patch
- use BIT-macro
- make constants better readable
- use dev_err instead of pr_*
- change dt-binding include due to renaming (phy-snps-pcie3.h => phy-rockchip-pcie3.h)
- use exclusive variant of devm_reset_control_get{,_exclusive}
- fix semicolon.cocci warnings reported by kernel test robot <[email protected]>
---
driver was taken from linux 5.10 based on in
https://github.com/JeffyCN/mirrors
which now has disappeared
--- drivers/phy/rockchip/Kconfig | 9 + drivers/phy/rockchip/Makefile | 1 + .../phy/rockchip/phy-rockchip-snps-pcie3.c | 317 ++++++++++++++++++ include/linux/phy/pcie.h | 12 + 4 files changed, 339 insertions(+) create mode 100644 drivers/phy/rockchip/phy-rockchip-snps-pcie3.c create mode 100644 include/linux/phy/pcie.h
drivers/phy/rockchip/Kconfig +9 -0
@@ -83,6 +83,15 @@ config PHY_ROCKCHIP_PCIE help Enable this to support the Rockchip PCIe PHY. +config PHY_ROCKCHIP_SNPS_PCIE3 + tristate "Rockchip Snps PCIe3 PHY Driver" + depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST + depends on HAS_IOMEM + select GENERIC_PHY + select MFD_SYSCON + help + Enable this to support the Rockchip snps PCIe3 PHY. + config PHY_ROCKCHIP_TYPEC tristate "Rockchip TYPEC PHY Driver" depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
drivers/phy/rockchip/Makefile +1 -0
@@ -8,5 +8,6 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI) += phy-rockchip-inno-hdmi.o obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY) += phy-rockchip-naneng-combphy.o obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o +obj-$(CONFIG_PHY_ROCKCHIP_SNPS_PCIE3) += phy-rockchip-snps-pcie3.o obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +317 -0
317 lines not on this page · raw message
include/linux/phy/pcie.h new file +12 -0
@@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Copyright (c) 2021 Rockchip Electronics Co., Ltd. +*/ +#ifndef __PHY_PCIE_H +#define __PHY_PCIE_H + +#define PHY_MODE_PCIE_RC 20 +#define PHY_MODE_PCIE_EP 21 +#define PHY_MODE_PCIE_BIFURCATION 22 + +#endif
Signature · 1 line
2.25.1
RFC v3 5/5 arm64: dts: rockchip: Add PCIe v3 nodes to BPI-R2-Pro
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add Nodes to Bananapi-R2-Pro board to support PCIe v3 and set PCIe related regulators to always on.
---
v3:
- squash lane-map over bifurcation property
- add comment which slot is M2 and which one if mPCIe
- fixes from Peter:
- drop regulator-always-on/regulator-boot-on from regulators
- increase startup-delay-us for regulators
- set phy-mode on PCIe3-phy
- add num-lanes to PCIe overrides
- add usb node for to PCIe/m2
- move lane-map from PCIe controller to PCIe-phy
v2:
- underscores in nodenames
- rockchip,bifurcation to vendor unspecific bifurcation
- fix trailing space
--- .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts | 90 +++++++++++++++++++ 1 file changed, 90 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts +90 -0
@@ -74,6 +74,62 @@ vcc5v0_sys: vcc5v0-sys { vin-supply = <&dc_12v>; }; + pcie30_avdd0v9: pcie30-avdd0v9 { + compatible = "regulator-fixed"; + regulator-name = "pcie30_avdd0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + vin-supply = <&vcc3v3_sys>; + }; + + pcie30_avdd1v8: pcie30-avdd1v8 { + compatible = "regulator-fixed"; + regulator-name = "pcie30_avdd1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc3v3_sys>; + }; + + /* pi6c pcie clock generator feeds both ports */ + vcc3v3_pi6c_05: vcc3v3-pi6c-05-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_pcie"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; + startup-delay-us = <200000>; + vin-supply = <&vcc5v0_sys>; + }; + + /* actually fed by vcc3v3_sys, dependent on pi6c clock generator */ + vcc3v3_minipcie: vcc3v3-minipcie-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_minipcie"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; + startup-delay-us = <50000>; + vin-supply = <&vcc3v3_pi6c_05>; + }; + + /* actually fed by vcc3v3_sys, dependent on pi6c clock generator */ + vcc3v3_ngff: vcc3v3-ngff-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_ngff"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>; + startup-delay-us = <50000>; + vin-supply = <&vcc3v3_pi6c_05>; + }; + vbus: vbus { compatible = "regulator-fixed"; regulator-name = "vbus";
@@ -411,6 +467,27 @@ rgmii_phy1: ethernet-phy@0 { }; }; +&pcie30phy { + lane-map = /bits/ 8 <1 2>; + status = "okay"; +}; + +&pcie3x1 { + /* M.2 slot */ + num-lanes = <1>; + reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_ngff>; + status = "okay"; +}; + +&pcie3x2 { + /* mPCIe slot */ + num-lanes = <1>; + reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_minipcie>; + status = "okay"; +}; + &pinctrl { leds { blue_led_pin: blue-led-pin {
@@ -597,3 +674,16 @@ &usb2phy0_otg { phy-supply = <&vcc5v0_usb_otg>; status = "okay"; }; + +&usb2phy1 { + /* USB for PCIe/M2 */ + status = "okay"; +}; + +&usb2phy1_host { + status = "okay"; +}; + +&usb2phy1_otg { + status = "okay"; +};
Signature · 1 line
2.25.1
RFC v3 4/5 arm64: dts: rockchip: rk3568: Add PCIe v3 nodes
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add nodes to rk356x devicetree to support PCIe v3.
---
v3:
- fix from Peter: change bus-range and msi-map, msi-map needs to start from 0x0
v2:
- change to compatible with soc-part
- change rockchip,bifurcation to vendor unspecific bifurcation
--- arch/arm64/boot/dts/rockchip/rk3568.dtsi | 122 +++++++++++++++++++++++ 1 file changed, 122 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568.dtsi +122 -0
@@ -42,6 +42,128 @@ qos_sata0: qos@fe190200 { reg = <0x0 0xfe190200 0x0 0x20>; }; + pcie30_phy_grf: syscon@fdcb8000 { + compatible = "rockchip,rk3568-pcie3-phy-grf", "syscon"; + reg = <0x0 0xfdcb8000 0x0 0x10000>; + }; + + pcie30phy: phy@fe8c0000 { + compatible = "rockchip,rk3568-pcie3-phy"; + reg = <0x0 0xfe8c0000 0x0 0x20000>; + #phy-cells = <0>; + clocks = <&pmucru CLK_PCIE30PHY_REF_M>, <&pmucru CLK_PCIE30PHY_REF_N>, + <&cru PCLK_PCIE30PHY>; + clock-names = "refclk_m", "refclk_n", "pclk"; + resets = <&cru SRST_PCIE30PHY>; + reset-names = "phy"; + rockchip,phy-grf = <&pcie30_phy_grf>; + status = "disabled"; + }; + + pcie3x1: pcie@fe270000 { + compatible = "rockchip,rk3568-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xf>; + clocks = <&cru ACLK_PCIE30X1_MST>, <&cru ACLK_PCIE30X1_SLV>, + <&cru ACLK_PCIE30X1_DBI>, <&cru PCLK_PCIE30X1>, + <&cru CLK_PCIE30X1_AUX_NDFT>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", "aux"; + device_type = "pci"; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie3x1_intc 0>, + <0 0 0 2 &pcie3x1_intc 1>, + <0 0 0 3 &pcie3x1_intc 2>, + <0 0 0 4 &pcie3x1_intc 3>; + linux,pci-domain = <1>; + num-ib-windows = <6>; + num-ob-windows = <2>; + max-link-speed = <3>; + msi-map = <0x0 &gic 0x1000 0x1000>; + num-lanes = <1>; + phys = <&pcie30phy>; + phy-names = "pcie-phy"; + power-domains = <&power RK3568_PD_PIPE>; + reg = <0x3 0xc0400000 0x0 0x00400000>, + <0x0 0xfe270000 0x0 0x00010000>, + <0x3 0x40000000 0x0 0x01000000>; + ranges = <0x01000000 0x0 0x01000000 0x3 0x41000000 0x0 0x00100000>, + <0x02000000 0x0 0x02000000 0x3 0x41100000 0x0 0x3ef00000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE30X1_POWERUP>; + reset-names = "pipe"; + /* bifurcation; lane1 when using 1+1 */ + status = "disabled"; + + pcie3x1_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>; + }; + }; + + pcie3x2: pcie@fe280000 { + compatible = "rockchip,rk3568-pcie"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xf>; + clocks = <&cru ACLK_PCIE30X2_MST>, <&cru ACLK_PCIE30X2_SLV>, + <&cru ACLK_PCIE30X2_DBI>, <&cru PCLK_PCIE30X2>, + <&cru CLK_PCIE30X2_AUX_NDFT>; + clock-names = "aclk_mst", "aclk_slv", + "aclk_dbi", "pclk", "aux"; + device_type = "pci"; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "sys", "pmc", "msg", "legacy", "err"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie3x2_intc 0>, + <0 0 0 2 &pcie3x2_intc 1>, + <0 0 0 3 &pcie3x2_intc 2>, + <0 0 0 4 &pcie3x2_intc 3>; + linux,pci-domain = <2>; + num-ib-windows = <6>; + num-ob-windows = <2>; + max-link-speed = <3>; + msi-map = <0x0 &gic 0x2000 0x1000>; + num-lanes = <2>; + phys = <&pcie30phy>; + phy-names = "pcie-phy"; + power-domains = <&power RK3568_PD_PIPE>; + reg = <0x3 0xc0800000 0x0 0x00400000>, + <0x0 0xfe280000 0x0 0x00010000>, + <0x3 0x80000000 0x0 0x01000000>; + ranges = <0x01000000 0x0 0x01000000 0x3 0x81000000 0x0 0x00100000>, + <0x02000000 0x0 0x02000000 0x3 0x81100000 0x0 0x3ef00000>; + reg-names = "dbi", "apb", "config"; + resets = <&cru SRST_PCIE30X2_POWERUP>; + reset-names = "pipe"; + /* bifurcation; lane0 when using 1+1 */ + status = "disabled"; + + pcie3x2_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>; + }; + }; + gmac0: ethernet@fe2a0000 { compatible = "rockchip,rk3568-gmac", "snps,dwmac-4.20a"; reg = <0x0 0xfe2a0000 0x0 0x10000>;
Signature · 1 line
2.25.1
Re: [RFC v3 2/5] dt-bindings: soc: grf: add pcie30-{phy,pipe}-grf
In reply to Frank WunderlichQuoted 5 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Add compatibles for PCIe v3 General Register Files.
Signed-off-by Frank Wunderlich <[email protected]>
Best regards,
Krzysztof
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
In reply to Frank WunderlichQuoted 6 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Add a new binding file for Rockchip PCIe v3 phy driver.
Signed-off-by Frank Wunderlich <[email protected]>
Best regards,
Krzysztof
Rob Herring
maintainerRe: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
In reply to Frank WunderlichQuoted 26 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Add a new binding file for Rockchip PCIe v3 phy driver.
Signed-off-by Frank Wunderlich <[email protected]>---
v3:
- drop quotes
- drop rk3588
- make clockcount fixed to 3
- full path for binding header file
- drop phy-mode and its header and add lane-mapv2:
dt-bindings: rename yaml for PCIe v3rockchip-pcie3-phy.yaml=> rockchip,pcie3-phy.yamlchanges in pcie3 phy yaml
- change clock names to ordered const list
- extend pcie30-phymode description
- add phy-cells to required properties
- drop unevaluatedProperties
- example with 1 clock each line
- use default property instead of text describing it
- update license
Quoted 5 lines
--- .../bindings/phy/rockchip,pcie3-phy.yaml | 82 +++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml: properties:clock-names: 'oneOf' conditional failed, one must be fixed:
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}] is too long
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}] is too short
False schema does not allow 3
1 was expected
3 is greater than the maximum of 2
hint: "minItems" is only needed if less than the "items" list length
from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml: ignoring, error in schema: properties: clock-names Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.example.dtb:0:0: /example-0/phy@fe8c0000: failed to match any schema with compatible: ['rockchip,rk3568-pcie3-phy']
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/
This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:
pip3 install dtschema --upgrade
Please check and re-submit.
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Aw: Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
Hi
Quoted 41 lines
Gesendet: Sonntag, 15. Mai 2022 um 01:14 Uhr
Von: "Rob Herring" <[email protected]>Quoted 26 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Add a new binding file for Rockchip PCIe v3 phy driver.
Signed-off-by Frank Wunderlich <[email protected]>---
v3:
- drop quotes
- drop rk3588
- make clockcount fixed to 3
- full path for binding header file
- drop phy-mode and its header and add lane-mapv2:
dt-bindings: rename yaml for PCIe v3rockchip-pcie3-phy.yaml=> rockchip,pcie3-phy.yamlchanges in pcie3 phy yaml
- change clock names to ordered const list
- extend pcie30-phymode description
- add phy-cells to required properties
- drop unevaluatedProperties
- example with 1 clock each line
- use default property instead of text describing it
- update licenseQuoted 5 lines
--- .../bindings/phy/rockchip,pcie3-phy.yaml | 82 +++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yamlMy bot found errors running 'make DT_CHECKER_FLAGS=-m
dt_binding_check' on your patch (DT_CHECKER_FLAGSis new in v5.13):yamllint warnings/errors:
Quoted 11 lines
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml: properties:clock-names: 'oneOf' conditional failed, one must be fixed:
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}] is too long
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}] is too short
False schema does not allow 3
1 was expected
3 is greater than the maximum of 2
hint: "minItems" is only needed if less than the "items" list length
from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml: ignoring, error in schema: properties: clock-namesDocumentation/devicetree/bindings/phy/rockchip,pcie3-phy.example.dtb:0:0: /example-0/phy@fe8c0000: failed to match any schema with compatible: ['rockchip,rk3568-pcie3-phy']
seems this is fixed when i remove the "minItems: 3" from clock names (which is already fixed length because of the list).
needed to change type of lane-map to this:
$ref: /schemas/types.yaml#/definitions/uint8-array
then it looks clean for it....
-m causes many errors unrelated to this schema-file even if i pass DT_SCHEMA_FILES=Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
will wait a bit for other comments (for driver) till i send another version. maybe you can confirm my changes are the right way to fix.
regards Frank
Rob Herring
maintainerRe: Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
Quoted 55 lines · Frank Wunderlich
Hi
Quoted 41 lines
Gesendet: Sonntag, 15. Mai 2022 um 01:14 Uhr
Von: "Rob Herring" <[email protected]>Quoted 26 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Add a new binding file for Rockchip PCIe v3 phy driver.
Signed-off-by Frank Wunderlich <[email protected]>---
v3:
- drop quotes
- drop rk3588
- make clockcount fixed to 3
- full path for binding header file
- drop phy-mode and its header and add lane-mapv2:
dt-bindings: rename yaml for PCIe v3rockchip-pcie3-phy.yaml=> rockchip,pcie3-phy.yamlchanges in pcie3 phy yaml
- change clock names to ordered const list
- extend pcie30-phymode description
- add phy-cells to required properties
- drop unevaluatedProperties
- example with 1 clock each line
- use default property instead of text describing it
- update licenseQuoted 5 lines
--- .../bindings/phy/rockchip,pcie3-phy.yaml | 82 +++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yamlMy bot found errors running 'make DT_CHECKER_FLAGS=-m
dt_binding_check' on your patch (DT_CHECKER_FLAGSis new in v5.13):yamllint warnings/errors:
Quoted 11 lines
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml: properties:clock-names: 'oneOf' conditional failed, one must be fixed:
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}] is too long
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}] is too short
False schema does not allow 3
1 was expected
3 is greater than the maximum of 2
hint: "minItems" is only needed if less than the "items" list length
from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml: ignoring, error in schema: properties: clock-namesDocumentation/devicetree/bindings/phy/rockchip,pcie3-phy.example.dtb:0:0: /example-0/phy@fe8c0000: failed to match any schema with compatible: ['rockchip,rk3568-pcie3-phy']
Quoted 2 lines
seems this is fixed when i remove the "minItems: 3" from clock names (which is already fixed length because of the list).
Yes.
Quoted 3 lines
needed to change type of lane-map to this:
$ref: /schemas/types.yaml#/definitions/uint8-array
Why? That's not a standard property though, so needs a 'rockchip' prefix. Though maybe a common property would be appropriate here.
Quoted 4 lines
then it looks clean for it....
-m causes many errors unrelated to this schema-file even if i pass DT_SCHEMA_FILES=Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
The fix is fixing the remaining 40 or so '-m' errors.
Rob
Re: Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
Am 16. Mai 2022 19:35:37 MESZ schrieb Rob Herring <[email protected]>:
Quoted 42 lines · Frank Wunderlich
Quoted 6 lines
Hi
Quoted 4 lines
Gesendet: Sonntag, 15. Mai 2022 um 01:14 Uhr
Von: "Rob Herring" <[email protected]>On Sat, 14 May 2022 13:59:42 +0200, Frank Wunderlich wrote:
Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yamlQuoted 3 lines
Quoted 3 lines
Quoted 1 line
My bot found errors running 'make DT_CHECKER_FLAGS=-m
dt_binding_check'Quoted 6 lines
Quoted 6 lines
on your patch (
DT_CHECKER_FLAGSis new in v5.13):yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml:
properties:clock-names: 'oneOf' conditional failed, one must be fixed:Quoted 1 line
Quoted 1 line
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}]is too long
Quoted 1 line
Quoted 1 line
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}]is too short
Quoted 4 lines
Quoted 4 lines
False schema does not allow 3
1 was expected
3 is greater than the maximum of 2
hint: "minItems" is only needed if less than the "items" listlength
Quoted 2 lines
Quoted 2 lines
from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml:
ignoring, error in schema: properties: clock-namesQuoted 1 line
Quoted 1 line
Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.example.dtb:0:0:
/example-0/phy@fe8c0000: failed to match any schema with compatible:
['rockchip,rk3568-pcie3-phy']Quoted 3 lines
seems this is fixed when i remove the "minItems: 3" from clock names (which is already fixed length because of the list).
Quoted 8 lines
Yes.
Quoted 3 lines
needed to change type of lane-map to this:
$ref: /schemas/types.yaml#/definitions/uint8-array
Why? That's not a standard property though, so needs a 'rockchip' prefix. Though maybe a common property would be appropriate here.
Originally it was a bool property named "rockchip,bifurcation" and we changed it (after comments) to be a more generic property "lane-map" that can be re-used on other vendors/controllers/phys.
Driver reads as u8 array and range is small enough for u8 even if used for larger controllers (e.g. PCIe x16).
Quoted 7 lines
Quoted 4 lines
then it looks clean for it....
-m causes many errors unrelated to this schema-file even if i pass
DT_SCHEMA_FILES=Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
The fix is fixing the remaining 40 or so '-m' errors.
So now clean for you(r bot), too? Did only get a bunch of other unrelated messages.
Quoted 1 line
Rob
regards Frank
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Rob Herring
maintainerRe: Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
Quoted 47 lines · Frank Wunderlich
Am 16. Mai 2022 19:35:37 MESZ schrieb Rob Herring <[email protected]>:
Quoted 46 lines · Frank Wunderlich
Quoted 6 lines
Hi
Quoted 4 lines
Gesendet: Sonntag, 15. Mai 2022 um 01:14 Uhr
Von: "Rob Herring" <[email protected]>On Sat, 14 May 2022 13:59:42 +0200, Frank Wunderlich wrote:
Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yamlQuoted 3 lines
Quoted 3 lines
Quoted 1 line
My bot found errors running 'make DT_CHECKER_FLAGS=-m
dt_binding_check'Quoted 6 lines
Quoted 6 lines
on your patch (
DT_CHECKER_FLAGSis new in v5.13):yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml:
properties:clock-names: 'oneOf' conditional failed, one must be fixed:Quoted 1 line
Quoted 1 line
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}]is too long
Quoted 1 line
Quoted 1 line
[{'const': 'refclk_m'}, {'const': 'refclk_n'}, {'const': 'pclk'}]is too short
Quoted 4 lines
Quoted 4 lines
False schema does not allow 3
1 was expected
3 is greater than the maximum of 2
hint: "minItems" is only needed if less than the "items" listlength
Quoted 2 lines
Quoted 2 lines
from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml:
ignoring, error in schema: properties: clock-namesQuoted 1 line
Quoted 1 line
Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.example.dtb:0:0:
/example-0/phy@fe8c0000: failed to match any schema with compatible:
['rockchip,rk3568-pcie3-phy']Quoted 3 lines
seems this is fixed when i remove the "minItems: 3" from clock names (which is already fixed length because of the list).
Yes.
Quoted 2 lines
needed to change type of lane-map to this:
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
$ref: /schemas/types.yaml#/definitions/uint8-array
Why? That's not a standard property though, so needs a 'rockchip' prefix. Though maybe a common property would be appropriate here.
Originally it was a bool property named "rockchip,bifurcation" and we changed it (after comments) to be a more generic property "lane-map" that can be re-used on other vendors/controllers/phys.
Fair enough. The type needs to be defined in a common binding though. phy/phy-provider.yaml in dtschema probably.
We already have clock-lanes and data-lanes for other serdes interfaces. Maybe data-lanes works here?
Quoted 2 lines
Driver reads as u8 array and range is small enough for u8 even if used for larger controllers (e.g. PCIe x16).
Not arguing that it shouldn't be, just confused how the type was related to warnings.
Quoted 10 lines
Quoted 8 lines
Quoted 5 lines
then it looks clean for it....
-m causes many errors unrelated to this schema-file even if i pass
DT_SCHEMA_FILES=Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
The fix is fixing the remaining 40 or so '-m' errors.
So now clean for you(r bot), too? Did only get a bunch of other unrelated messages.
No, the bot does a baseline build and extracts the diff in warnings. Still too many warnings popping up frequently... :(
Rob
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Aw: Re: Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
Hi,
fixed reg-error by using 32bit-address in example, in my test output is clean.
+++ b/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml @@ -68,7 +68,7 @@ examples:
#include <dt-bindings/clock/rk3568-cru.h>
pcie30phy: phy@fe8c0000 {
compatible = "rockchip,rk3568-pcie3-phy";- reg = <0x0 0xfe8c0000 0x0 0x20000>;
+ reg = <0xfe8c0000 0x20000>;
i hope yours is clean too
regarding data-lanes instead of own lane-map, Peter and me only find this in special bindings outside the phy-"namespace" like this.
do you mean converting this binding and add it there and base out binding on it?
regards Frank
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Aw: Re: Re: [RFC v3 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy
Quoted 16 lines
Gesendet: Freitag, 20. Mai 2022 um 13:50 Uhr
Von: "Frank Wunderlich" <[email protected]>
An: "Rob Herring" <[email protected]>
Hi,fixed reg-error by using 32bit-address in example, in my test output is clean.
+++
b/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml(quoted diff) +1
-1@@ -68,7 +68,7 @@ examples: #include <dt-bindings/clock/rk3568-cru.h> pcie30phy: phy@fe8c0000 { compatible = "rockchip,rk3568-pcie3-phy"; - reg = <0x0 0xfe8c0000 0x0 0x20000>; + reg = <0xfe8c0000 0x20000>;
Quoted 1 line
i hope yours is clean too
have you tried it?
Quoted 8 lines
regarding data-lanes instead of own lane-map, Peter and me only find this in special bindings outside the phy-"namespace" like this.
do you mean converting this binding and add it there and base out binding on it?
is this the right binding to add the data-lanes or do you refer another one (have not found phy-provider)?
regards Frank
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy