ARM: imx: Add support for iMX6QDL DHCOM DRC02 and DH picoITX
v2 cover ARM: imx: Add support for iMX6QDL DHCOM DRC02 and DH picoITX
This patch series adds support for the DHCOM DRC02 and DH picoITX baseboards by DH electronics.
The two boards can be equipped with different SoMs. The STM32MP15xx based versions are already mainlined. This patch adds support for the iMX6QDL based variants.
Changes in v2:
- Rewrite board_fit_config_name_match
- Return -EINVAL instead of -1
- Reviewed-by Marek
- Fix spelling
Philip Oberfichtner (8):
ARM: imx6: Fix broken DT path in DH board file
ARM: dts: imx: Migrate iMX6QDL DRC02 DTs from Linux
ARM: dts: imx: Migrate iMX6QDL picoITX DTs from Linux
ARM: imx6: Remove CONFIG_FEC_MXC_PHYADDR from DH header
ARM: dts: imx: Simplify fec node for iMX6QDL DHCOM boards
ARM: dts: imx: Configure FEC for iMX6QDL picoITX
ARM: dts: imx: Configure FEC for iMX6QDL DRC02
ARM: imx6: Adapt device tree selection in DH board file
arch/arm/dts/Makefile | 2 + arch/arm/dts/imx6dl-dhcom-picoitx-u-boot.dtsi | 10 ++ arch/arm/dts/imx6dl-dhcom-picoitx.dts | 20 +++ arch/arm/dts/imx6qdl-dhcom-drc02.dtsi | 143 ++++++++++++++++++ arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi | 13 -- arch/arm/dts/imx6qdl-dhcom-picoitx.dtsi | 69 +++++++++ arch/arm/dts/imx6qdl-dhcom-u-boot.dtsi | 18 +++ arch/arm/dts/imx6s-dhcom-drc02-u-boot.dtsi | 10 ++ arch/arm/dts/imx6s-dhcom-drc02.dts | 30 ++++ board/dhelectronics/dh_imx6/dh_imx6.c | 35 ++++- configs/dh_imx6_defconfig | 2 +- include/configs/dh_imx6.h | 3 - 12 files changed, 330 insertions(+), 25 deletions(-) create mode 100644 arch/arm/dts/imx6dl-dhcom-picoitx-u-boot.dtsi create mode 100644 arch/arm/dts/imx6dl-dhcom-picoitx.dts create mode 100644 arch/arm/dts/imx6qdl-dhcom-drc02.dtsi create mode 100644 arch/arm/dts/imx6qdl-dhcom-picoitx.dtsi create mode 100644 arch/arm/dts/imx6s-dhcom-drc02-u-boot.dtsi create mode 100644 arch/arm/dts/imx6s-dhcom-drc02.dts
Signature · 1 line
2.34.1
PATCH v2 1/8 ARM: imx6: Fix broken DT path in DH board file
In the DH electronics iMX6 board file fix the outdated eeprom path by using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
---
Changes in v2:
- Reviewed-by Marek
arch/arm/dts/imx6qdl-dhcom-u-boot.dtsi | 11 +++++++++++ board/dhelectronics/dh_imx6/dh_imx6.c | 4 ++-- 2 files changed, 13 insertions(+), 2 deletions(-)
arch/arm/dts/imx6qdl-dhcom-u-boot.dtsi +11 -0
@@ -3,6 +3,17 @@ * Copyright (C) 2020 Harald Seiler <[email protected]> */ +/ { + aliases { + eeprom0 = &eeprom0; + }; +}; + +&i2c3 { + eeprom0: eeprom@50 { + }; +}; + ®_usb_otg_vbus { gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; enable-active-high;
board/dhelectronics/dh_imx6/dh_imx6.c +2 -2
@@ -100,9 +100,9 @@ static int setup_dhcom_mac_from_fuse(void)return 0 ; } - eeprom =ofnode_path ("/soc/aips-bus@2100000/i2c@21a8000/eeprom@50" ); + eeprom =ofnode_get_aliases_node ("eeprom0" );if (!ofnode_valid (eeprom)) { -printf ("Invalid hardware path to EEPROM!\n" ); +printf ("Can't find eeprom0 alias!\n" );return -ENODEV ; }
Signature · 1 line
2.34.1
PATCH v2 2/8 ARM: dts: imx: Migrate iMX6QDL DRC02 DTs from Linux
In reply to Philip OberfichtnerMigrate DH DRC02 device trees from Linux commit 42226c989789 (tag v5.18-rc7). No changes have been made, the DTs are exact copies. Furthermore add the DTB to dh_imx6_defconfig.
---
(no changes since v1)
arch/arm/dts/Makefile | 1 + arch/arm/dts/imx6qdl-dhcom-drc02.dtsi | 143 ++++++++++++++++++++++++++ arch/arm/dts/imx6s-dhcom-drc02.dts | 30 ++++++ configs/dh_imx6_defconfig | 2 +- 4 files changed, 175 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx6qdl-dhcom-drc02.dtsi create mode 100644 arch/arm/dts/imx6s-dhcom-drc02.dts
arch/arm/dts/Makefile +1 -0
@@ -771,6 +771,7 @@ dtb-y += \ imx6dl-sabreauto.dtb \ imx6dl-sabresd.dtb \ imx6dl-wandboard-revd1.dtb \ + imx6s-dhcom-drc02.dtb endif
arch/arm/dts/imx6qdl-dhcom-drc02.dtsi new file +143 -0
143 lines not on this page · raw message
arch/arm/dts/imx6s-dhcom-drc02.dts new file +30 -0
@@ -0,0 +1,30 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 DH electronics GmbH + * + * DHCOM iMX6 variant: + * DHCM-iMX6S-C0800-R102-F0409-E-CAN2-RTC-I-01D2 + * DHCOM PCB number: 493-400 or newer + * DRC02 PCB number: 568-100 or newer + */ +/dts-v1/; + +/* + * The kernel only distinguishes between i.MX6 Quad and DualLite, + * but the Solo is actually a DualLite with only one CPU. So use + * DualLite for the Solo and disable one CPU node. + */ + +#include "imx6dl.dtsi" +#include "imx6qdl-dhcom-som.dtsi" +#include "imx6qdl-dhcom-drc02.dtsi" + +/ { + model = "DH electronics i.MX6S DHCOM on DRC02"; + compatible = "dh,imx6s-dhcom-drc02", "dh,imx6s-dhcom-som", + "fsl,imx6dl"; + + cpus { + /delete-node/ cpu@1; + }; +};
configs/dh_imx6_defconfig +1 -1
@@ -53,7 +53,7 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4_WRITE=y CONFIG_OF_CONTROL=y -CONFIG_OF_LIST="imx6q-dhcom-pdk2 imx6dl-dhcom-pdk2" +CONFIG_OF_LIST="imx6q-dhcom-pdk2 imx6dl-dhcom-pdk2 imx6s-dhcom-drc02" CONFIG_MULTI_DTB_FIT=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y
Signature · 1 line
2.34.1
PATCH v2 3/8 ARM: dts: imx: Migrate iMX6QDL picoITX DTs from Linux
In reply to Philip OberfichtnerMigrate DH picoITX device trees from Linux commit 42226c989789 (tag v5.18-rc7). No changes have been made, the DTs are exact copies. Furthermore add the DTB to dh_imx6_defconfig.
---
(no changes since v1)
arch/arm/dts/Makefile | 1 + arch/arm/dts/imx6dl-dhcom-picoitx.dts | 20 +++++++ arch/arm/dts/imx6qdl-dhcom-picoitx.dtsi | 69 +++++++++++++++++++++++++ configs/dh_imx6_defconfig | 2 +- 4 files changed, 91 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx6dl-dhcom-picoitx.dts create mode 100644 arch/arm/dts/imx6qdl-dhcom-picoitx.dtsi
arch/arm/dts/Makefile +1 -0
@@ -738,6 +738,7 @@ dtb-y += \ imx6dl-cubox-i-emmc-som-v15.dtb \ imx6dl-cubox-i-som-v15.dtb \ imx6dl-dhcom-pdk2.dtb \ + imx6dl-dhcom-picoitx.dts \ imx6dl-gw51xx.dtb \ imx6dl-gw52xx.dtb \ imx6dl-gw53xx.dtb \
arch/arm/dts/imx6dl-dhcom-picoitx.dts new file +20 -0
@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 DH electronics GmbH + * + * DHCOM iMX6 variant: + * DHCM-iMX6DL-C0800-R102-F0819-E-SD-RTC-T-HS-I-01D2 + * DHCOM PCB number: 493-300 or newer + * PicoITX PCB number: 487-600 or newer + */ +/dts-v1/; + +#include "imx6dl.dtsi" +#include "imx6qdl-dhcom-som.dtsi" +#include "imx6qdl-dhcom-picoitx.dtsi" + +/ { + model = "DH electronics i.MX6DL DHCOM on PicoITX"; + compatible = "dh,imx6dl-dhcom-picoitx", "dh,imx6dl-dhcom-som", + "fsl,imx6dl"; +};
arch/arm/dts/imx6qdl-dhcom-picoitx.dtsi new file +69 -0
69 lines not on this page · raw message
configs/dh_imx6_defconfig +1 -1
@@ -53,7 +53,7 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_EXT4_WRITE=y CONFIG_OF_CONTROL=y -CONFIG_OF_LIST="imx6q-dhcom-pdk2 imx6dl-dhcom-pdk2 imx6s-dhcom-drc02" +CONFIG_OF_LIST="imx6q-dhcom-pdk2 imx6dl-dhcom-pdk2 imx6s-dhcom-drc02 imx6dl-dhcom-picoitx" CONFIG_MULTI_DTB_FIT=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_SPI_FLASH=y
Signature · 1 line
2.34.1
PATCH v2 5/8 ARM: dts: imx: Simplify fec node for iMX6QDL DHCOM boards
In reply to Philip OberfichtnerFirstly the FEC can now use the regulator reg_eth_vio from imx6qdl-dhcom-som.dtsi instead of defining its own.
Secondly the &fec node is moved to the more generic SoM device tree file, because it can be used by multiple boards.
---
Changes in v2:
- Reviewed-by Marek
arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi | 13 ------------- arch/arm/dts/imx6qdl-dhcom-u-boot.dtsi | 7 +++++++ 2 files changed, 7 insertions(+), 13 deletions(-)
arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi +0 -13
@@ -5,19 +5,6 @@ #include "imx6qdl-dhcom-u-boot.dtsi" -/ { - fec_vio: regulator-fec { - compatible = "regulator-fixed"; - - regulator-name = "fec-vio"; - gpio = <&gpio1 7 GPIO_ACTIVE_LOW>; - }; -}; - &fec { phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; - phy-reset-duration = <1>; - phy-reset-post-delay = <10>; - - phy-supply = <&fec_vio>; };
arch/arm/dts/imx6qdl-dhcom-u-boot.dtsi +7 -0
@@ -1,6 +1,7 @@ // SPDX-License-Identifier: (GPL-2.0+) /* * Copyright (C) 2020 Harald Seiler <[email protected]> + * Copyright (C) 2022 Philip Oberfichtner <[email protected]> */ / {
@@ -9,6 +10,12 @@ }; }; +&fec { + phy-reset-duration = <1>; + phy-reset-post-delay = <10>; + phy-supply = <®_eth_vio>; +}; + &i2c3 { eeprom0: eeprom@50 { };
Signature · 1 line
2.34.1
PATCH v2 4/8 ARM: imx6: Remove CONFIG_FEC_MXC_PHYADDR from DH header
In reply to Philip OberfichtnerUse phy address from device tree instead of CONFIG_FEC_MXC_PHYADDR from board header. This is required, because the DH picoITX and DRC02 boards require different settings than PDK2. The corresponding 'phy-handle' device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.
---
(no changes since v1)
include/configs/dh_imx6.h | 3 --- 1 file changed, 3 deletions(-)
include/configs/dh_imx6.h +0 -3
@@ -30,9 +30,6 @@/* Bootcounter */ #define CONFIG_SYS_BOOTCOUNT_BE -/* FEC ethernet */ -#define CONFIG_FEC_MXC_PHYADDR 7 -/* MMC Configs */ #define CONFIG_SYS_FSL_ESDHC_ADDR 0#define CONFIG_SYS_FSL_USDHC_NUM 3
Signature · 1 line
2.34.1
PATCH v2 7/8 ARM: dts: imx: Configure FEC for iMX6QDL DRC02
In reply to Philip OberfichtnerAdd a u-boot dtsi for configuring the FEC node of the DH DRC02.
---
Changes in v2:
- Reviewed-by Marek
arch/arm/dts/imx6s-dhcom-drc02-u-boot.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) create mode 100644 arch/arm/dts/imx6s-dhcom-drc02-u-boot.dtsi
arch/arm/dts/imx6s-dhcom-drc02-u-boot.dtsi new file +10 -0
@@ -0,0 +1,10 @@ +// SPDX-License-Identifier: (GPL-2.0+) +/* + * Copyright (C) 2022 Philip Oberfichtner <[email protected]> + */ + +#include "imx6qdl-dhcom-u-boot.dtsi" + +&fec { + phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; +};
Signature · 1 line
2.34.1
PATCH v2 6/8 ARM: dts: imx: Configure FEC for iMX6QDL picoITX
In reply to Philip OberfichtnerAdd a u-boot dtsi for configuring the FEC node of the DH picoITX.
---
Changes in v2:
- Reviewed-by Marek
arch/arm/dts/imx6dl-dhcom-picoitx-u-boot.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) create mode 100644 arch/arm/dts/imx6dl-dhcom-picoitx-u-boot.dtsi
arch/arm/dts/imx6dl-dhcom-picoitx-u-boot.dtsi new file +10 -0
@@ -0,0 +1,10 @@ +// SPDX-License-Identifier: (GPL-2.0+) +/* + * Copyright (C) 2022 Philip Oberfichtner <[email protected]> + */ + +#include "imx6qdl-dhcom-u-boot.dtsi" + +&fec { + phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; +};
Signature · 1 line
2.34.1
PATCH v2 8/8 ARM: imx6: Adapt device tree selection in DH board file
In reply to Philip OberfichtnerBefore this commit device tree selection could rely solely on differentiating the iMX6 processor variant Q and DL. After adding two new carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02, dhcom-picoitx or dhcom-pdk2) at compile time using CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.
---
Changes in v2:
- Rewrite board_fit_config_name_match
- Return -EINVAL instead of -1
board/dhelectronics/dh_imx6/dh_imx6.c | 31 +++++++++++++++++++++------ 1 file changed, 25 insertions(+), 6 deletions(-)
board/dhelectronics/dh_imx6/dh_imx6.c +25 -6
@@ -225,16 +225,35 @@ int checkboard(void) }#ifdef CONFIG_MULTI_DTB_FIT +static int strcmp_prefix (const char *s1,const char *s2) +{ +size_t n; + + n =min (strlen (s1),strlen (s2)); +return strncmp (s1, s2, n); +} +int board_fit_config_name_match (const char *name) { -if (is_mx6dq ()) { -if (!strcmp (name,"imx6q-dhcom-pdk2" )) -return 0 ; - }else if (is_mx6sdl ()) { -if (!strcmp (name,"imx6dl-dhcom-pdk2" )) +char *want; +char *have; + +/* Test Board suffix, e.g. -dhcom-drc02 */ + want =strchr (CONFIG_DEFAULT_DEVICE_TREE ,'-' ); + have =strchr (name,'-' ); + +if (!want || !have ||strcmp (want, have)) +return -EINVAL ; + +/* Test SoC prefix */ +if (is_mx6dq () && !strcmp_prefix (name,"imx6q-" )) +return 0 ; + +if (is_mx6sdl ()) { +if (!strcmp_prefix (name,"imx6s-" ) || !strcmp_prefix (name,"imx6dl-" ))return 0 ; } -return -1 ; +return -EINVAL ; }#endif
Signature · 1 line
2.34.1
Re: [PATCH v2 8/8] ARM: imx6: Adapt device tree selection in DH board file
Quoted 10 lines · Philip Oberfichtner
Before this commit device tree selection could rely solely on differentiating the iMX6 processor variant Q and DL. After adding two new carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02, dhcom-picoitx or dhcom-pdk2) at compile time using
CONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.Signed-off-by Philip Oberfichtner <[email protected]>
Hi Philip,
Quoted 13 lines · Philip Oberfichtner
This patch series adds support for the DHCOM DRC02 and DH picoITX baseboards by DH electronics.
The two boards can be equipped with different SoMs. The STM32MP15xx based versions are already mainlined. This patch adds support for the iMX6QDL based variants.
Changes in v2:
- Rewriteboard_fit_config_name_match
- Return-EINVALinstead of -1
- Reviewed-by Marek
- Fix spelling
Quoted 9 lines
Philip Oberfichtner (8):
ARM: imx6: Fix broken DT path in DH board file
ARM: dts: imx: Migrate iMX6QDL DRC02 DTs from Linux
ARM: dts: imx: Migrate iMX6QDL picoITX DTs from Linux
ARM: imx6: RemoveCONFIG_FEC_MXC_PHYADDRfrom DH header
ARM: dts: imx: Simplify fec node for iMX6QDL DHCOM boards
ARM: dts: imx: Configure FEC for iMX6QDL picoITX
ARM: dts: imx: Configure FEC for iMX6QDL DRC02
ARM: imx6: Adapt device tree selection in DH board file
For the series:
PATCH v2 4/8 ARM: imx6: Remove CONFIG_FEC_MXC_PHYADDR from DH header
In reply to Philip OberfichtnerQuoted 7 lines
Use phy address from device tree instead of
CONFIG_FEC_MXC_PHYADDRfrom board header. This is required, because the DH picoITX and DRC02 boards require different settings than PDK2. The corresponding 'phy-handle' device tree properties are already there.
I tested this change on picoITX and DRC02, but on PDK2 it is untested.Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 6/8 ARM: dts: imx: Configure FEC for iMX6QDL picoITX
In reply to Philip OberfichtnerQuoted 3 lines
Add a u-boot dtsi for configuring the FEC node of the DH picoITX.
Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 1/8 ARM: imx6: Fix broken DT path in DH board file
In reply to Philip OberfichtnerQuoted 5 lines
In the DH electronics iMX6 board file fix the outdated eeprom path by using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 7/8 ARM: dts: imx: Configure FEC for iMX6QDL DRC02
In reply to Philip OberfichtnerQuoted 3 lines
Add a u-boot dtsi for configuring the FEC node of the DH DRC02.
Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 5/8 ARM: dts: imx: Simplify fec node for iMX6QDL DHCOM boards
In reply to Philip OberfichtnerQuoted 6 lines
Firstly the FEC can now use the regulator
reg_eth_viofromimx6qdl-dhcom-som.dtsiinstead of defining its own. Secondly the &fec node is moved to the more generic SoM device tree file, because it can be used by multiple boards.Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 8/8 ARM: imx6: Adapt device tree selection in DH board file
In reply to Philip OberfichtnerQuoted 8 lines
Before this commit device tree selection could rely solely on differentiating the iMX6 processor variant Q and DL. After adding two new carrier boards, the DRC02 and the picoITX, the interchangeability of SoMs makes this approach infeasible.
It is now required to specify the carrier board (dhcom-drc02, dhcom-picoitx or dhcom-pdk2) at compile time usingCONFIG_DEFAULT_DEVICETREE. The SoM is determined at runtime as before.Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 3/8 ARM: dts: imx: Migrate iMX6QDL picoITX DTs from Linux
In reply to Philip OberfichtnerQuoted 5 lines
Migrate DH picoITX device trees from Linux commit
42226c989789(tag v5.18-rc7). No changes have been made, the DTs are exact copies. Furthermore add the DTB todh_imx6_defconfig.Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH v2 2/8 ARM: dts: imx: Migrate iMX6QDL DRC02 DTs from Linux
In reply to Philip OberfichtnerQuoted 5 lines
Migrate DH DRC02 device trees from Linux commit
42226c989789(tag v5.18-rc7). No changes have been made, the DTs are exact copies. Furthermore add the DTB todh_imx6_defconfig.Reviewed-by Marek Vasut <[email protected]>Signed-off-by Philip Oberfichtner <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================