firmware: ti_sci_static_data: Make file board agnostic
PATCH 1/1 firmware: ti_sci_static_data: Make file board agnostic
Static DMA channel data for R5 SPL is mostly board agnostic so use SOC configs instead of EVM specific config to ease adding new board support.
Drop J7200 EVM specific settings as its same as J721e
Signed-off-by Vignesh Raghavendra <[email protected]>
--- drivers/firmware/ti_sci_static_data.h | 42 +++------------------------ 1 file changed, 4 insertions(+), 38 deletions(-)
drivers/firmware/ti_sci_static_data.h +4 -38
@@ -16,7 +16,7 @@ struct ti_sci_resource_static_data { #if IS_ENABLED(CONFIG_K3_DM_FW) -#if IS_ENABLED(CONFIG_TARGET_J721E_R5_EVM) +#if IS_ENABLED(CONFIG_SOC_K3_J721E) static struct ti_sci_resource_static_data rm_static_data[] = { /* Free rings */ {
@@ -48,43 +48,9 @@ static struct ti_sci_resource_static_data rm_static_data[] = { }, { }, }; -#endif /* CONFIG_TARGET_J721E_R5_EVM */ +#endif /* CONFIG_SOC_K3_J721E */ -#if IS_ENABLED (CONFIG_TARGET_J7200_R5_EVM ) -static struct ti_sci_resource_static_data rm_static_data[] = { -/* Free rings */ - { - .dev_id =235 , - .subtype =1 , - .range_start =124 , - .range_num =32 , - }, -/* TX channels */ - { - .dev_id =236 , - .subtype =13 , - .range_start =6 , - .range_num =2 , - }, -/* RX channels */ - { - .dev_id =236 , - .subtype =10 , - .range_start =6 , - .range_num =2 , - }, -/* RX Free flows */ - { - .dev_id =236 , - .subtype =0 , - .range_start =60 , - .range_num =8 , - }, - { }, -}; -#endif /* CONFIG_TARGET_J7200_R5_EVM */ - -#if IS_ENABLED(CONFIG_TARGET_J721S2_R5_EVM) +#if IS_ENABLED(CONFIG_SOC_K3_J721S2) static struct ti_sci_resource_static_data rm_static_data[] = { /* Free rings */ {
@@ -116,7 +82,7 @@ static struct ti_sci_resource_static_data rm_static_data[] = { }, { }, }; -#endif /* CONFIG_TARGET_J721S2_R5_EVM */ +#endif /* CONFIG_SOC_K3_J721S2 */ #if IS_ENABLED (CONFIG_SOC_K3_AM625 ) static struct ti_sci_resource_static_data rm_static_data[] = {
Signature · 1 line
2.36.1
Quoted 6 lines · Vignesh Raghavendra
Static DMA channel data for R5 SPL is mostly board agnostic so use SOC configs instead of EVM specific config to ease adding new board support.
Drop J7200 EVM specific settings as its same as J721e
Signed-off-by Vignesh Raghavendra <[email protected]>
Gee thanks.
Reviewed-by Nishanth Menon <[email protected]>
Quoted 75 lines
--- drivers/firmware/ti_sci_static_data.h | 42 +++------------------------ 1 file changed, 4 insertions(+), 38 deletions(-)drivers/firmware/ti_sci_static_data.h +4
-38@@ -16,7 +16,7 @@ struct ti_sci_resource_static_data { #if IS_ENABLED(CONFIG_K3_DM_FW) -#if IS_ENABLED(CONFIG_TARGET_J721E_R5_EVM) +#if IS_ENABLED(CONFIG_SOC_K3_J721E) static struct ti_sci_resource_static_data rm_static_data[] = { /* Free rings */ {@@ -48,43 +48,9 @@ static struct ti_sci_resource_static_data rm_static_data[] = { }, { }, }; -#endif /* CONFIG_TARGET_J721E_R5_EVM */ +#endif /* CONFIG_SOC_K3_J721E */ -#if IS_ENABLED (CONFIG_TARGET_J7200_R5_EVM ) -static struct ti_sci_resource_static_data rm_static_data[] = { -/* Free rings */ - { - .dev_id =235 , - .subtype =1 , - .range_start =124 , - .range_num =32 , - }, -/* TX channels */ - { - .dev_id =236 , - .subtype =13 , - .range_start =6 , - .range_num =2 , - }, -/* RX channels */ - { - .dev_id =236 , - .subtype =10 , - .range_start =6 , - .range_num =2 , - }, -/* RX Free flows */ - { - .dev_id =236 , - .subtype =0 , - .range_start =60 , - .range_num =8 , - }, - { }, -}; -#endif /* CONFIG_TARGET_J7200_R5_EVM */ - -#if IS_ENABLED(CONFIG_TARGET_J721S2_R5_EVM) +#if IS_ENABLED(CONFIG_SOC_K3_J721S2) static struct ti_sci_resource_static_data rm_static_data[] = { /* Free rings */ {@@ -116,7 +82,7 @@ static struct ti_sci_resource_static_data rm_static_data[] = { }, { }, }; -#endif /* CONFIG_TARGET_J721S2_R5_EVM */ +#endif /* CONFIG_SOC_K3_J721S2 */ #if IS_ENABLED (CONFIG_SOC_K3_AM625 ) static struct ti_sci_resource_static_data rm_static_data[] = {Signature · 1 line
2.36.1
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Quoted 7 lines · Vignesh Raghavendra
Static DMA channel data for R5 SPL is mostly board agnostic so use SOC configs instead of EVM specific config to ease adding new board support.
Drop J7200 EVM specific settings as its same as J721e
Signed-off-by Vignesh Raghavendra <[email protected]>Reviewed-by Nishanth Menon <[email protected]>
Applied to u-boot/next, thanks!
Signature · 1 line
Tom