Skip to contentSkip to conversation

RK3568 PCIe V3 support

PATCH Superseded Frank Wunderlich 3 participants 10 messages Jun 19, 2022 – Aug 1, 2022

Subsystems (3)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#1 lore raw

PATCH v4 1/5 dt-bindings: phy: rockchip: add PCIe v3 phy

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add a new binding file for Rockchip PCIe v3 phy driver.

---
v4:
- add reviewed-by
- remove minitems for clock-names as i have static list to fix error
- fix reg error by using 32-bit adressing in binding example
- change lane-map to u32 data-lanes
- tried to move data-lanes to phy-provider
https://github.com/frank-w/dt-schema/blob/main/dtschema/schemas/phy/phy-provider.yaml#L17
cloned and installed via pip install -e <local path> verified with pip show, but phy-privider seems not to be applied

v3:
- drop quotes
- drop rk3588
- make clockcount fixed to 3
- full path for binding header file
- drop phy-mode and its header and add lane-map

v2:
dt-bindings: rename yaml for PCIe v3 rockchip-pcie3-phy.yaml => rockchip,pcie3-phy.yaml

changes in pcie3 phy yaml
- change clock names to ordered const list
- extend pcie30-phymode description
- add phy-cells to required properties
- drop unevaluatedProperties
- example with 1 clock each line
- use default property instead of text describing it
- update license

---
 .../bindings/phy/rockchip,pcie3-phy.yaml      | 80 +++++++++++++++++++
 1 file changed, 80 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml new file +80 -0
new file mode 100644
index 000000000000..9f2d8d2cc7a5
@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/rockchip,pcie3-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip PCIe v3 phy
+
+maintainers:
+  - Heiko Stuebner <[email protected]>
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk3568-pcie3-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    minItems: 3
+    maxItems: 3
+
+  clock-names:
+    items:
+      - const: refclk_m
+      - const: refclk_n
+      - const: pclk
+
+  data-lanes:
+    description: which lanes (by position) should be mapped to which
+      controller (value). 0 means lane disabled, higher value means used.
+      (controller-number +1 )
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 16
+    items:
+      minimum: 0
+      maximum: 16
+
+  "#phy-cells":
+    const: 0
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: phy
+
+  rockchip,phy-grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to the syscon managing the phy "general register files"
+
+  rockchip,pipe-grf:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to the syscon managing the pipe "general register files"
+
+required:
+  - compatible
+  - reg
+  - rockchip,phy-grf
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/rk3568-cru.h>
+    pcie30phy: phy@fe8c0000 {
+      compatible = "rockchip,rk3568-pcie3-phy";
+      reg = <0xfe8c0000 0x20000>;
+      #phy-cells = <0>;
+      clocks = <&pmucru CLK_PCIE30PHY_REF_M>,
+               <&pmucru CLK_PCIE30PHY_REF_N>,
+               <&cru PCLK_PCIE30PHY>;
+      clock-names = "refclk_m", "refclk_n", "pclk";
+      resets = <&cru SRST_PCIE30PHY>;
+      reset-names = "phy";
+      rockchip,phy-grf = <&pcie30_phy_grf>;
+    };
Signature · 1 line
2.34.1
#0 lore raw

v4 cover RK3568 PCIe V3 support

From: Frank Wunderlich <[email protected]>

This series adds Rockchip PCIe V3 support found on rk3568 SOC.

Compared to PCIeV2 which uses the Naneng combphy, PCIe v3 uses a dedicated PCI-phy.

Frank Wunderlich (4):
dt-bindings: phy: rockchip: add PCIe v3 phy
dt-bindings: soc: grf: add pcie30-{phy,pipe}-grf
arm64: dts: rockchip: rk3568: Add PCIe v3 nodes
arm64: dts: rockchip: Add PCIe v3 nodes to BPI-R2-Pro

Shawn Lin (1):
phy: rockchip: Support PCIe v3

 .../bindings/phy/rockchip,pcie3-phy.yaml      |  80 +++++
 .../devicetree/bindings/soc/rockchip/grf.yaml |   3 +
 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   |  90 +++++
 arch/arm64/boot/dts/rockchip/rk3568.dtsi      | 122 +++++++
 drivers/phy/rockchip/Kconfig                  |   9 +
 drivers/phy/rockchip/Makefile                 |   1 +
 .../phy/rockchip/phy-rockchip-snps-pcie3.c    | 317 ++++++++++++++++++
 include/linux/phy/pcie.h                      |  12 +
 8 files changed, 634 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml
 create mode 100644 drivers/phy/rockchip/phy-rockchip-snps-pcie3.c
 create mode 100644 include/linux/phy/pcie.h
Signature · 1 line
2.34.1
#3 lore raw

PATCH v4 2/5 dt-bindings: soc: grf: add pcie30-{phy,pipe}-grf

From: Frank Wunderlich <[email protected]>

Add compatibles for PCIe v3 General Register Files.

---
v4:
- rebase on 5.19-rc1
- add acked-by

v3:
- fix order of grf-bindings

v2:
- add soc-part to pcie3-phy-grf

---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 3 +++
 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/soc/rockchip/grf.yaml +3 -0
index 75a2b8bb25fb..97301c470173 100644
@@ -16,9 +16,12 @@ properties:
           - enum:
               - rockchip,rk3288-sgrf
               - rockchip,rk3566-pipe-grf
+              - rockchip,rk3568-pcie3-phy-grf
               - rockchip,rk3568-pipe-grf
               - rockchip,rk3568-pipe-phy-grf
               - rockchip,rk3568-usb2phy-grf
+              - rockchip,rk3588-pcie3-phy-grf
+              - rockchip,rk3588-pcie3-pipe-grf
               - rockchip,rv1108-usbgrf
           - const: syscon
       - items:
Signature · 1 line
2.34.1
#4 lore raw

PATCH v4 3/5 phy: rockchip: Support PCIe v3

In reply to Frank Wunderlich

From: Shawn Lin <[email protected]>

RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566. It use a dedicated PCIe-phy. Add support for this.

Initial support by Shawn Lin, modifications by Peter Geis and Frank Wunderlich.

Add data-lanes property for splitting pcie-lanes across controllers.

The data-lanes is an array where x=0 means lane is disabled and x > 0 means controller x is assigned to phy lane.

---
v4:
- change u8 lane-map to u32 data-lanes

v3:
- change dt-binding include
- change reset to devm_reset_control_get_optional_exclusive exit on error and lower severity of message if unset
- fix from peter: disable reg-write for phy-mode in rockchip_p3phy_probe
- move bifurcation/lane-map support from PCIe to phy driver

v2:
- move dt-bindings header into separate patch
- use BIT-macro
- make constants better readable
- use dev_err instead of pr_*
- change dt-binding include due to renaming (phy-snps-pcie3.h => phy-rockchip-pcie3.h)
- use exclusive variant of devm_reset_control_get{,_exclusive}
- fix semicolon.cocci warnings reported by kernel test robot <[email protected]>

---
driver was taken from linux 5.10 based on in
https://github.com/JeffyCN/mirrors
which now has disappeared

Update phy-rockchip-snps-pcie3.c

Fix messages for data-lanes

Update phy-rockchip-snps-pcie3.c

Fix comment for data-lanes

---
 drivers/phy/rockchip/Kconfig                  |   9 +
 drivers/phy/rockchip/Makefile                 |   1 +
 .../phy/rockchip/phy-rockchip-snps-pcie3.c    | 317 ++++++++++++++++++
 include/linux/phy/pcie.h                      |  12 +
 4 files changed, 339 insertions(+)
 create mode 100644 drivers/phy/rockchip/phy-rockchip-snps-pcie3.c
 create mode 100644 include/linux/phy/pcie.h
drivers/phy/rockchip/Kconfig +9 -0
index 9022e395c056..94360fc96a6f 100644
@@ -83,6 +83,15 @@ config PHY_ROCKCHIP_PCIE
 	help
 	  Enable this to support the Rockchip PCIe PHY.
 
+config PHY_ROCKCHIP_SNPS_PCIE3
+	tristate "Rockchip Snps PCIe3 PHY Driver"
+	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the Rockchip snps PCIe3 PHY.
+
 config PHY_ROCKCHIP_TYPEC
 	tristate "Rockchip TYPEC PHY Driver"
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
drivers/phy/rockchip/Makefile +1 -0
index a5041efb5b8f..7eab129230d1 100644
@@ -8,5 +8,6 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
 obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
+obj-$(CONFIG_PHY_ROCKCHIP_SNPS_PCIE3)	+= phy-rockchip-snps-pcie3.o
 obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +317 -0

317 lines not on this page · raw message

include/linux/phy/pcie.h new file +12 -0
new file mode 100644
index 000000000000..93c997f520fe
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ */
+#ifndef __PHY_PCIE_H
+#define __PHY_PCIE_H
+
+#define PHY_MODE_PCIE_RC 20
+#define PHY_MODE_PCIE_EP 21
+#define PHY_MODE_PCIE_BIFURCATION 22
+
+#endif
Signature · 1 line
2.34.1
#8 lore raw

PATCH v4 4/5 arm64: dts: rockchip: rk3568: Add PCIe v3 nodes

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add nodes to rk356x devicetree to support PCIe v3.

---
v4:
- update pcie3 reg/ranges

v3:
- fix from Peter: change bus-range and msi-map, msi-map needs to start from 0x0

v2:
- change to compatible with soc-part
- change rockchip,bifurcation to vendor unspecific bifurcation

---
 arch/arm64/boot/dts/rockchip/rk3568.dtsi | 122 +++++++++++++++++++++++
 1 file changed, 122 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568.dtsi +122 -0
index 5eafddf62edc..3f568f6747f6 100644
@@ -42,6 +42,128 @@ qos_sata0: qos@fe190200 {
 		reg = <0x0 0xfe190200 0x0 0x20>;
 	};
 
+	pcie30_phy_grf: syscon@fdcb8000 {
+		compatible = "rockchip,rk3568-pcie3-phy-grf", "syscon";
+		reg = <0x0 0xfdcb8000 0x0 0x10000>;
+	};
+
+	pcie30phy: phy@fe8c0000 {
+		compatible = "rockchip,rk3568-pcie3-phy";
+		reg = <0x0 0xfe8c0000 0x0 0x20000>;
+		#phy-cells = <0>;
+		clocks = <&pmucru CLK_PCIE30PHY_REF_M>, <&pmucru CLK_PCIE30PHY_REF_N>,
+			 <&cru PCLK_PCIE30PHY>;
+		clock-names = "refclk_m", "refclk_n", "pclk";
+		resets = <&cru SRST_PCIE30PHY>;
+		reset-names = "phy";
+		rockchip,phy-grf = <&pcie30_phy_grf>;
+		status = "disabled";
+	};
+
+	pcie3x1: pcie@fe270000 {
+		compatible = "rockchip,rk3568-pcie";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xf>;
+		clocks = <&cru ACLK_PCIE30X1_MST>, <&cru ACLK_PCIE30X1_SLV>,
+			 <&cru ACLK_PCIE30X1_DBI>, <&cru PCLK_PCIE30X1>,
+			 <&cru CLK_PCIE30X1_AUX_NDFT>;
+		clock-names = "aclk_mst", "aclk_slv",
+			      "aclk_dbi", "pclk", "aux";
+		device_type = "pci";
+		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie3x1_intc 0>,
+				<0 0 0 2 &pcie3x1_intc 1>,
+				<0 0 0 3 &pcie3x1_intc 2>,
+				<0 0 0 4 &pcie3x1_intc 3>;
+		linux,pci-domain = <1>;
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		max-link-speed = <3>;
+		msi-map = <0x0 &gic 0x1000 0x1000>;
+		num-lanes = <1>;
+		phys = <&pcie30phy>;
+		phy-names = "pcie-phy";
+		power-domains = <&power RK3568_PD_PIPE>;
+		reg = <0x3 0xc0400000 0x0 0x00400000>,
+		      <0x0 0xfe270000 0x0 0x00010000>,
+		      <0x3 0x7f000000 0x0 0x01000000>;
+		ranges = <0x01000000 0x0 0x3ef00000 0x3 0x7ef00000 0x0 0x00100000>,
+			 <0x02000000 0x0 0x00000000 0x3 0x40000000 0x0 0x3ef00000>;
+		reg-names = "dbi", "apb", "config";
+		resets = <&cru SRST_PCIE30X1_POWERUP>;
+		reset-names = "pipe";
+		/* bifurcation; lane1 when using 1+1 */
+		status = "disabled";
+
+		pcie3x1_intc: legacy-interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	pcie3x2: pcie@fe280000 {
+		compatible = "rockchip,rk3568-pcie";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xf>;
+		clocks = <&cru ACLK_PCIE30X2_MST>, <&cru ACLK_PCIE30X2_SLV>,
+			 <&cru ACLK_PCIE30X2_DBI>, <&cru PCLK_PCIE30X2>,
+			 <&cru CLK_PCIE30X2_AUX_NDFT>;
+		clock-names = "aclk_mst", "aclk_slv",
+			      "aclk_dbi", "pclk", "aux";
+		device_type = "pci";
+		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie3x2_intc 0>,
+				<0 0 0 2 &pcie3x2_intc 1>,
+				<0 0 0 3 &pcie3x2_intc 2>,
+				<0 0 0 4 &pcie3x2_intc 3>;
+		linux,pci-domain = <2>;
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		max-link-speed = <3>;
+		msi-map = <0x0 &gic 0x2000 0x1000>;
+		num-lanes = <2>;
+		phys = <&pcie30phy>;
+		phy-names = "pcie-phy";
+		power-domains = <&power RK3568_PD_PIPE>;
+		reg = <0x3 0xc0800000 0x0 0x00400000>,
+		      <0x0 0xfe280000 0x0 0x00010000>,
+		      <0x3 0xbf000000 0x0 0x01000000>;
+		ranges = <0x01000000 0x0 0x3ef00000 0x3 0xbef00000 0x0 0x00100000>,
+			 <0x02000000 0x0 0x00000000 0x3 0x80000000 0x0 0x3ef00000>;
+		reg-names = "dbi", "apb", "config";
+		resets = <&cru SRST_PCIE30X2_POWERUP>;
+		reset-names = "pipe";
+		/* bifurcation; lane0 when using 1+1 */
+		status = "disabled";
+
+		pcie3x2_intc: legacy-interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
 	gmac0: ethernet@fe2a0000 {
 		compatible = "rockchip,rk3568-gmac", "snps,dwmac-4.20a";
 		reg = <0x0 0xfe2a0000 0x0 0x10000>;
Signature · 1 line
2.34.1
#9 lore raw

PATCH v4 5/5 arm64: dts: rockchip: Add PCIe v3 nodes to BPI-R2-Pro

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Nodes to Bananapi-R2-Pro board to support PCIe v3 and set PCIe related regulators to always on.

---
v4:
- change u8 lane-map to u32 data-lanes

v3:
- squash lane-map over bifurcation property
- add comment which slot is M2 and which one if mPCIe
- fixes from Peter:
- drop regulator-always-on/regulator-boot-on from regulators
- increase startup-delay-us for regulators
- set phy-mode on PCIe3-phy
- add num-lanes to PCIe overrides
- add usb node for to PCIe/m2
- move lane-map from PCIe controller to PCIe-phy

v2:
- underscores in nodenames
- rockchip,bifurcation to vendor unspecific bifurcation
- fix trailing space

---
 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   | 90 +++++++++++++++++++
 1 file changed, 90 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts +90 -0
index 40cf2236c0b6..dd688019ca49 100644
@@ -74,6 +74,62 @@ vcc5v0_sys: vcc5v0-sys {
 		vin-supply = <&dc_12v>;
 	};
 
+	pcie30_avdd0v9: pcie30-avdd0v9 {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: pcie30-avdd1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* pi6c pcie clock generator feeds both ports */
+	vcc3v3_pi6c_05: vcc3v3-pi6c-05-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <200000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	/* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+	vcc3v3_minipcie: vcc3v3-minipcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_minipcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc3v3_pi6c_05>;
+	};
+
+	/* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+	vcc3v3_ngff: vcc3v3-ngff-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_ngff";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc3v3_pi6c_05>;
+	};
+
 	vcc5v0_usb: vcc5v0_usb {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc5v0_usb";
@@ -401,6 +457,27 @@ rgmii_phy1: ethernet-phy@0 {
 	};
 };
 
+&pcie30phy {
+	data-lanes = <1 2>;
+	status = "okay";
+};
+
+&pcie3x1 {
+	/* M.2 slot */
+	num-lanes = <1>;
+	reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_ngff>;
+	status = "okay";
+};
+
+&pcie3x2 {
+	/* mPCIe slot */
+	num-lanes = <1>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_minipcie>;
+	status = "okay";
+};
+
 &pinctrl {
 	leds {
 		blue_led_pin: blue-led-pin {
@@ -587,3 +664,16 @@ &usb2phy0_otg {
 	phy-supply = <&vcc5v0_usb_otg>;
 	status = "okay";
 };
+
+&usb2phy1 {
+	/* USB for PCIe/M2 */
+	status = "okay";
+};
+
+&usb2phy1_host {
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	status = "okay";
+};
Signature · 1 line
2.34.1
#5 lore raw

Aw: [PATCH v4 3/5] phy: rockchip: Support PCIe v3

In reply to Frank Wunderlich

Hi,

just a gentle ping :)

regards Frank

Quoted 18 lines

Gesendet: Sonntag, 19. Juni 2022 um 10:26 Uhr
Von: "Frank Wunderlich" <[email protected]>
From: Shawn Lin <[email protected]>

RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566. It use a dedicated PCIe-phy. Add support for this.

Initial support by Shawn Lin, modifications by Peter Geis and Frank Wunderlich.

Add data-lanes property for splitting pcie-lanes across controllers.

The data-lanes is an array where x=0 means lane is disabled and x > 0 means controller x is assigned to phy lane.

Signature · 3 lines
linux-phy mailing list
[email protected]
https://lists.infradead.org/mailman/listinfo/linux-phy
maintainer
#6 lore raw

Re: [PATCH v4 3/5] phy: rockchip: Support PCIe v3

In reply to Frank Wunderlich
Quoted 94 lines · Frank Wunderlich

From: Shawn Lin <[email protected]>

RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566. It use a dedicated PCIe-phy. Add support for this.

Initial support by Shawn Lin, modifications by Peter Geis and Frank Wunderlich.

Add data-lanes property for splitting pcie-lanes across controllers.

The data-lanes is an array where x=0 means lane is disabled and x > 0 means controller x is assigned to phy lane.

---
v4:
- change u8 lane-map to u32 data-lanes

v3:
- change dt-binding include
- change reset to devm_reset_control_get_optional_exclusive exit on error and lower severity of message if unset
- fix from peter: disable reg-write for phy-mode in rockchip_p3phy_probe
- move bifurcation/lane-map support from PCIe to phy driver

v2:
- move dt-bindings header into separate patch
- use BIT-macro
- make constants better readable
- use dev_err instead of pr_*
- change dt-binding include due to renaming (phy-snps-pcie3.h => phy-rockchip-pcie3.h)
- use exclusive variant of devm_reset_control_get{,_exclusive}
- fix semicolon.cocci warnings reported by kernel test robot <[email protected]>

---
driver was taken from linux 5.10 based on in
https://github.com/JeffyCN/mirrors
which now has disappeared

Update phy-rockchip-snps-pcie3.c

Fix messages for data-lanes

Update phy-rockchip-snps-pcie3.c

Fix comment for data-lanes

---
 drivers/phy/rockchip/Kconfig                  |   9 +
 drivers/phy/rockchip/Makefile                 |   1 +
 .../phy/rockchip/phy-rockchip-snps-pcie3.c    | 317 ++++++++++++++++++
 include/linux/phy/pcie.h                      |  12 +
 4 files changed, 339 insertions(+)
 create mode 100644 drivers/phy/rockchip/phy-rockchip-snps-pcie3.c
 create mode 100644 include/linux/phy/pcie.h
drivers/phy/rockchip/Kconfig +9 -0
index 9022e395c056..94360fc96a6f 100644
@@ -83,6 +83,15 @@ config PHY_ROCKCHIP_PCIE
 	help
 	  Enable this to support the Rockchip PCIe PHY.
 
+config PHY_ROCKCHIP_SNPS_PCIE3
+	tristate "Rockchip Snps PCIe3 PHY Driver"
+	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the Rockchip snps PCIe3 PHY.
+
 config PHY_ROCKCHIP_TYPEC
 	tristate "Rockchip TYPEC PHY Driver"
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
drivers/phy/rockchip/Makefile +1 -0
index a5041efb5b8f..7eab129230d1 100644
@@ -8,5 +8,6 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI)	+= phy-rockchip-inno-hdmi.o
 obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
 obj-$(CONFIG_PHY_ROCKCHIP_NANENG_COMBO_PHY)	+= phy-rockchip-naneng-combphy.o
 obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
+obj-$(CONFIG_PHY_ROCKCHIP_SNPS_PCIE3)	+= phy-rockchip-snps-pcie3.o
 obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
 obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +0 -0
new file mode 100644
index 000000000000..e2be53492618

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 5

Quoted 5 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +5 -0
@@ -0,0 +1,317 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rockchip PCIE3.0 phy driver
+ *
+ * Copyright (C) 2020 Rockchip Electronics Co., Ltd.

2022 now :)

Quoted 77 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +77 -0
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/pcie.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* Register for RK3568 */
+#define GRF_PCIE30PHY_CON1			0x4
+#define GRF_PCIE30PHY_CON6			0x18
+#define GRF_PCIE30PHY_CON9			0x24
+#define GRF_PCIE30PHY_STATUS0			0x80
+#define SRAM_INIT_DONE(reg)			(reg & BIT(14))
+
+#define RK3568_BIFURCATION_LANE_0_1		BIT(0)
+
+/* Register for RK3588 */
+#define PHP_GRF_PCIESEL_CON			0x100
+#define RK3588_PCIE3PHY_GRF_CMN_CON0		0x0
+#define RK3588_PCIE3PHY_GRF_PHY0_STATUS1	0x904
+#define RK3588_PCIE3PHY_GRF_PHY1_STATUS1	0xa04
+#define RK3588_SRAM_INIT_DONE(reg)		(reg & BIT(0))
+
+#define RK3588_BIFURCATION_LANE_0_1		BIT(0)
+#define RK3588_BIFURCATION_LANE_2_3		BIT(1)
+#define RK3588_LANE_AGGREGATION		BIT(2)
+
+struct rockchip_p3phy_ops;
+
+struct rockchip_p3phy_priv {
+	const struct rockchip_p3phy_ops *ops;
+	void __iomem *mmio;
+	/* mode: RC, EP */
+	int mode;
+	/* pcie30_phymode: Aggregation, Bifurcation */
+	int pcie30_phymode;
+	struct regmap *phy_grf;
+	struct regmap *pipe_grf;
+	struct reset_control *p30phy;
+	struct phy *phy;
+	struct clk_bulk_data *clks;
+	int num_clks;
+	int num_lanes;
+	u32 lanes[4];
+};
+
+struct rockchip_p3phy_ops {
+	int (*phy_init)(struct rockchip_p3phy_priv *priv);
+};
+
+static int rockchip_p3phy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
+{
+	struct rockchip_p3phy_priv *priv = phy_get_drvdata(phy);
+
+	/* Actually We don't care EP/RC mode, but just record it */
+	switch (submode) {
+	case PHY_MODE_PCIE_RC:
+		priv->mode = PHY_MODE_PCIE_RC;
+		break;
+	case PHY_MODE_PCIE_EP:
+		priv->mode = PHY_MODE_PCIE_EP;
+		break;
+	default:
+		dev_err(&phy->dev, "%s, invalid mode\n", __func__);
+		return -EINVAL;
+	}
+
+	return 0;
+}

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 92

Quoted 10 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +10 -0
+
+static int rockchip_p3phy_rk3568_init(struct rockchip_p3phy_priv *priv)
+{
+	struct phy *phy = priv->phy;
+	bool bifurcation = false;
+	int ret;
+	u32 reg;
+
+	/* Deassert PCIe PMA output clamp mode */
+	regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON9, BIT(15) | BIT(31));

Can we define these bits..?

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 104

Quoted 12 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +12 -0
+
+	for (int i = 0; i < priv->num_lanes; i++) {
+		dev_info(&phy->dev, "lane number %d, val %d\n", i, priv->lanes[i]);
+		if (priv->lanes[i] > 1)
+			bifurcation = true;
+	}
+
+	/* Set bifurcation if needed, and it doesn't care RC/EP */
+	if (bifurcation) {
+		dev_info(&phy->dev, "bifurcation enabled\n");
+		regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON6,
+			     (0xf << 16) | RK3568_BIFURCATION_LANE_0_1);

upper word 0xf?

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 106

Quoted 2 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +2 -0
+		regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON1,
+			     BIT(15) | BIT(31));

again define bits please

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 108

Quoted 2 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +2 -0
+	} else {
+		dev_info(&phy->dev, "bifurcation disabled\n");

debug level?

Quoted 61 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +61 -0
+		regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON6,
+			     (0xf << 16) & ~RK3568_BIFURCATION_LANE_0_1);
+	}
+
+	reset_control_deassert(priv->p30phy);
+
+	ret = regmap_read_poll_timeout(priv->phy_grf,
+				       GRF_PCIE30PHY_STATUS0,
+				       reg, SRAM_INIT_DONE(reg),
+				       0, 500);
+	if (ret)
+		dev_err(&priv->phy->dev, "%s: lock failed 0x%x, check input refclk and power supply\n",
+		       __func__, reg);
+	return ret;
+}
+
+static const struct rockchip_p3phy_ops rk3568_ops = {
+	.phy_init = rockchip_p3phy_rk3568_init,
+};
+
+static int rockchip_p3phy_rk3588_init(struct rockchip_p3phy_priv *priv)
+{
+	u32 reg = 0;
+	u8 mode = 0;
+	int ret;
+
+	/* Deassert PCIe PMA output clamp mode */
+	regmap_write(priv->phy_grf, RK3588_PCIE3PHY_GRF_CMN_CON0, BIT(8) | BIT(24));
+
+	/* Set bifurcation if needed */
+	for (int i = 0; i < priv->num_lanes; i++) {
+		if (!priv->lanes[i])
+			mode |= (BIT(i) << 3);
+
+		if (priv->lanes[i] > 1)
+			mode |= (BIT(i) >> 1);
+	}
+
+	if (!mode)
+		reg = RK3588_LANE_AGGREGATION;
+	else {
+		if (mode & (BIT(0) | BIT(1)))
+			reg |= RK3588_BIFURCATION_LANE_0_1;
+
+		if (mode & (BIT(2) | BIT(3)))
+			reg |= RK3588_BIFURCATION_LANE_2_3;
+	}
+
+	regmap_write(priv->phy_grf, RK3588_PCIE3PHY_GRF_CMN_CON0, (0x7<<16) | reg);
+
+	/* Set pcie1ln_sel in PHP_GRF_PCIESEL_CON */
+	if (!IS_ERR(priv->pipe_grf)) {
+		reg = (mode & (BIT(6) | BIT(7))) >> 6;
+		if (reg)
+			regmap_write(priv->pipe_grf, PHP_GRF_PCIESEL_CON,
+				     (reg << 16) | reg);
+	}
+
+	reset_control_deassert(priv->p30phy);
+
+	ret = regmap_read_poll_timeout(priv->phy_grf,

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 179

Quoted 10 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +10 -0
+				       RK3588_PCIE3PHY_GRF_PHY0_STATUS1,
+				       reg, RK3588_SRAM_INIT_DONE(reg),
+				       0, 500);
+	ret |= regmap_read_poll_timeout(priv->phy_grf,
+					RK3588_PCIE3PHY_GRF_PHY1_STATUS1,
+					reg, RK3588_SRAM_INIT_DONE(reg),
+					0, 500);
+	if (ret)
+		pr_err("%s: lock failed 0x%x, check input refclk and power supply\n",
+		       __func__, reg);

Can this be made dev_err too, I still see bunch of pr_ and at least here you have driver context... while at it drop the __func__ from these logs too please

Quoted 144 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +138 -0
+	return ret;
+}
+
+static const struct rockchip_p3phy_ops rk3588_ops = {
+	.phy_init = rockchip_p3phy_rk3588_init,
+};
+
+static int rochchip_p3phy_init(struct phy *phy)
+{
+	struct rockchip_p3phy_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
+	if (ret) {
+		pr_err("failed to enable PCIe bulk clks %d\n", ret);
+		return ret;
+	}
+
+	reset_control_assert(priv->p30phy);
+	udelay(1);
+
+	if (priv->ops->phy_init) {
+		ret = priv->ops->phy_init(priv);
+		if (ret)
+			clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+	}
+
+	return ret;
+}
+
+static int rochchip_p3phy_exit(struct phy *phy)
+{
+	struct rockchip_p3phy_priv *priv = phy_get_drvdata(phy);
+
+	clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
+	reset_control_assert(priv->p30phy);
+	return 0;
+}
+
+static const struct phy_ops rochchip_p3phy_ops = {
+	.init = rochchip_p3phy_init,
+	.exit = rochchip_p3phy_exit,
+	.set_mode = rockchip_p3phy_set_mode,
+	.owner = THIS_MODULE,
+};
+
+static int rockchip_p3phy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct device *dev = &pdev->dev;
+	struct rockchip_p3phy_priv *priv;
+	struct device_node *np = dev->of_node;
+	struct resource *res;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->mmio = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->mmio)) {
+		ret = PTR_ERR(priv->mmio);
+		return ret;
+	}
+
+	priv->ops = of_device_get_match_data(&pdev->dev);
+	if (!priv->ops) {
+		dev_err(&pdev->dev, "no of match data provided\n");
+		return -EINVAL;
+	}
+
+	priv->phy_grf = syscon_regmap_lookup_by_phandle(np, "rockchip,phy-grf");
+	if (IS_ERR(priv->phy_grf)) {
+		dev_err(dev, "failed to find rockchip,phy_grf regmap\n");
+		return PTR_ERR(priv->phy_grf);
+	}
+
+	priv->pipe_grf = syscon_regmap_lookup_by_phandle(dev->of_node,
+							 "rockchip,pipe-grf");
+	if (IS_ERR(priv->pipe_grf))
+		dev_info(dev, "failed to find rockchip,pipe_grf regmap\n");
+
+	priv->num_lanes = of_property_read_variable_u32_array(dev->of_node, "data-lanes",
+							     priv->lanes, 2,
+							     ARRAY_SIZE(priv->lanes));
+
+	/* if no data-lanes assume aggregation */
+	if (priv->num_lanes == -EINVAL) {
+		dev_dbg(dev, "no data-lanes property found\n");
+		priv->num_lanes = 1;
+		priv->lanes[0] = 1;
+	} else if (priv->num_lanes < 0) {
+		dev_err(dev, "failed to read data-lanes property %d\n", priv->num_lanes);
+		return priv->num_lanes;
+	}
+
+	priv->phy = devm_phy_create(dev, NULL, &rochchip_p3phy_ops);
+	if (IS_ERR(priv->phy)) {
+		dev_err(dev, "failed to create combphy\n");
+		return PTR_ERR(priv->phy);
+	}
+
+	priv->p30phy = devm_reset_control_get_optional_exclusive(dev, "phy");
+	if (IS_ERR(priv->p30phy)) {
+		return dev_err_probe(dev, PTR_ERR(priv->p30phy),
+				     "failed to get phy reset control\n");
+	}
+	if (!priv->p30phy)
+		dev_info(dev, "no phy reset control specified\n");
+
+	priv->num_clks = devm_clk_bulk_get_all(dev, &priv->clks);
+	if (priv->num_clks < 1)
+		return -ENODEV;
+
+	dev_set_drvdata(dev, priv);
+	phy_set_drvdata(priv->phy, priv);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id rockchip_p3phy_of_match[] = {
+	{ .compatible = "rockchip,rk3568-pcie3-phy", .data = &rk3568_ops },
+	{ .compatible = "rockchip,rk3588-pcie3-phy", .data = &rk3588_ops },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, rockchip_p3phy_of_match);
+
+static struct platform_driver rockchip_p3phy_driver = {
+	.probe	= rockchip_p3phy_probe,
+	.driver = {
+		.name = "rockchip-snps-pcie3-phy",
+		.of_match_table = rockchip_p3phy_of_match,
+	},
+};
+module_platform_driver(rockchip_p3phy_driver);
+MODULE_DESCRIPTION("Rockchip Synopsys PCIe 3.0 PHY driver");
+MODULE_LICENSE("GPL");
include/linux/phy/pcie.h new file +0 -0
new file mode 100644
index 000000000000..93c997f520fe

include/linux/phy/pcie.h line 3

Quoted 3 lines
include/linux/phy/pcie.h new file +3 -0
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.

Header is 2021 !

Quoted 11 lines
include/linux/phy/pcie.h new file +9 -0
+ */
+#ifndef __PHY_PCIE_H
+#define __PHY_PCIE_H
+
+#define PHY_MODE_PCIE_RC 20
+#define PHY_MODE_PCIE_EP 21
+#define PHY_MODE_PCIE_BIFURCATION 22
+
+#endif
Signature · 1 line
2.34.1
Signature · 1 line
~Vinod
#7 lore raw

Aw: Re: [PATCH v4 3/5] phy: rockchip: Support PCIe v3

Hi

thanks for review.

Quoted 5 lines

Gesendet: Freitag, 15. Juli 2022 um 13:46 Uhr
Von: "Vinod Koul" <[email protected]>

Quoted 1 line

+ * Copyright (C) 2020 Rockchip Electronics Co., Ltd.

2022 now :)

ok, i change it

Quoted 4 lines

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 92

Quoted 2 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +2 -0
+	/* Deassert PCIe PMA output clamp mode */
+	regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON9, BIT(15) | BIT(31));

Can we define these bits..?

i have no naming found for it as these are not described in the TRM

maybe Peter or Liang/Shawn has these?

Quoted 6 lines
Quoted 6 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +6 -0
+
+	for (int i = 0; i < priv->num_lanes; i++) {
+		dev_info(&phy->dev, "lane number %d, val %d\n", i, priv->lanes[i]);
+		if (priv->lanes[i] > 1)
+			bifurcation = true;
+	}
Quoted 8 lines

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 104

Quoted 6 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +6 -0
+
+	/* Set bifurcation if needed, and it doesn't care RC/EP */
+	if (bifurcation) {
+		dev_info(&phy->dev, "bifurcation enabled\n");
+		regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON6,
+			     (0xf << 16) | RK3568_BIFURCATION_LANE_0_1);

upper word 0xf?

afaik yes (write-enable), is there any other more readable way?

Quoted 4 lines

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 106

Quoted 2 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +2 -0
+		regmap_write(priv->phy_grf, GRF_PCIE30PHY_CON1,
+			     BIT(15) | BIT(31));

again define bits please

these are not documented too

Quoted 4 lines

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 108

Quoted 2 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +2 -0
+	} else {
+		dev_info(&phy->dev, "bifurcation disabled\n");

debug level?

i made them same as the "bifurcation enabled" to have always an info about it in dmesg.

Quoted 7 lines

drivers/phy/rockchip/phy-rockchip-snps-pcie3.c line 179

Quoted 3 lines
drivers/phy/rockchip/phy-rockchip-snps-pcie3.c new file +3 -0
+	if (ret)
+		pr_err("%s: lock failed 0x%x, check input refclk and power supply\n",
+		       __func__, reg);

Can this be made dev_err too, I still see bunch of pr_ and at least here you have driver context... while at it drop the __func__ from these logs too please

ok, i'll change it

Quoted 11 lines

include/linux/phy/pcie.h line 3

Quoted 9 lines
include/linux/phy/pcie.h new file +3 -0
new file mode 100644
index 000000000000..93c997f520fe
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.

Header is 2021 !

i'll change

Quoted 2 lines

--
~Vinod

regards Frank

#2 lore raw

Aw: [PATCH v4 1/5] dt-bindings: phy: rockchip: add PCIe v3 phy

In reply to Frank Wunderlich

Hi Rob,

this (and the other bindings) part is marked as "not applicable", but without comment...it is not clear to me why it is not yet applied or how to proceed.

https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/

Do you expect driver-changes which will change binding too?

should i resend it unchanged in v5 (when 5.20-rc1 is out)? or do you try to move the data-lanes into phy-provider which i have not got working?

regards Frank