Skip to contentSkip to conversation

ice: add i2c write command

PATCH Superseded Karol Kolacinski 2 participants 3 messages Jun 23, 2022

Subsystems (4)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 ice: add i2c write command

Add the possibility to write to connected i2c devices using the AQ command. FW may reject the write if the device is not on allowlist.

---
 .../net/ethernet/intel/ice/ice_adminq_cmd.h   |  7 +--
 drivers/net/ethernet/intel/ice/ice_common.c   | 48 ++++++++++++++++++-
 drivers/net/ethernet/intel/ice/ice_common.h   |  4 ++
 3 files changed, 55 insertions(+), 4 deletions(-)
drivers/net/ethernet/intel/ice/ice_adminq_cmd.h +4 -3
index c018f6ff8ee2..64cfdb7edaa8 100644
@@ -1396,7 +1396,7 @@ struct ice_aqc_get_link_topo {
 	u8 rsvd[9];
 };
 
-/* Read I2C (direct, 0x06E2) */
+/* Read/Write I2C (direct, 0x06E2/0x06E3) */
 struct ice_aqc_i2c {
 	struct ice_aqc_link_topo_addr topo_addr;
 	__le16 i2c_addr;
@@ -1406,7 +1406,7 @@ struct ice_aqc_i2c {
 
 	u8 rsvd;
 	__le16 i2c_bus_addr;
-	u8 rsvd2[4];
+	u8 i2c_data[4]; /* Used only by write command, reserved in read. */
 };
 
 /* Read I2C Response (direct, 0x06E2) */
@@ -2125,7 +2125,7 @@ struct ice_aq_desc {
 		struct ice_aqc_get_link_status get_link_status;
 		struct ice_aqc_event_lan_overflow lan_overflow;
 		struct ice_aqc_get_link_topo get_link_topo;
-		struct ice_aqc_i2c read_i2c;
+		struct ice_aqc_i2c read_write_i2c;
 		struct ice_aqc_read_i2c_resp read_i2c_resp;
 	} params;
 };
@@ -2242,6 +2242,7 @@ enum ice_adminq_opc {
 	ice_aqc_opc_set_mac_lb				= 0x0620,
 	ice_aqc_opc_get_link_topo			= 0x06E0,
 	ice_aqc_opc_read_i2c				= 0x06E2,
+	ice_aqc_opc_write_i2c				= 0x06E3,
 	ice_aqc_opc_set_port_id_led			= 0x06E9,
 	ice_aqc_opc_set_gpio				= 0x06EC,
 	ice_aqc_opc_get_gpio				= 0x06ED,
drivers/net/ethernet/intel/ice/ice_common.c +47 -1

60 lines not on this page · raw message

drivers/net/ethernet/intel/ice/ice_common.h +4 -0
index 6a7764dd264c..a74df1d3a002 100644
@@ -215,5 +215,9 @@ int
 ice_aq_read_i2c(struct ice_hw *hw, struct ice_aqc_link_topo_addr topo_addr,
 		u16 bus_addr, __le16 addr, u8 params, u8 *data,
 		struct ice_sq_cd *cd);
+int
+ice_aq_write_i2c(struct ice_hw *hw, struct ice_aqc_link_topo_addr topo_addr,
+		 u16 bus_addr, __le16 addr, u8 params, u8 *data,
+		 struct ice_sq_cd *cd);
 bool ice_fw_supports_report_dflt_cfg(struct ice_hw *hw);
 #endif /* _ICE_COMMON_H_ */
Signature · 6 lines
2.34.1

_______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
#1 lore raw

PATCH 2/2 ice: add write functionality for GNSS TTY

Add the possibility to write raw bytes to the GNSS module through the first TTY device. This allows user to configure the module.

Create a second read-only TTY device.

---
 .../device_drivers/ethernet/intel/ice.rst     |   9 +
 drivers/net/ethernet/intel/ice/ice.h          |   4 +-
 drivers/net/ethernet/intel/ice/ice_gnss.c     | 242 ++++++++++++++++--
 drivers/net/ethernet/intel/ice/ice_gnss.h     |  30 ++-
 4 files changed, 254 insertions(+), 31 deletions(-)
Documentation/networking/device_drivers/ethernet/intel/ice.rst +9 -0
index 67b7a701ce9e..dc2e60ced927 100644
@@ -901,6 +901,15 @@ To enable/disable UDP Segmentation Offload, issue the following command::
 
   # ethtool -K <ethX> tx-udp-segmentation [off|on]
 
+GNSS module
+-----------
+Allows user to read messages from the GNSS module and write supported commands.
+If the module is physically present, driver creates 2 TTYs for each supported
+device in /dev, ttyGNSS_<device>:<function>_0 and _1. First one (_0) is RW and
+the second one is RO.
+The protocol of write commands is dependent on the GNSS module as the driver
+writes raw bytes from the TTY to the GNSS i2c. Please refer to the module
+documentation for details.
 
 Performance Optimization
 ========================
drivers/net/ethernet/intel/ice/ice.h +2 -2
index 70ed8afdbf2b..3f18aa7d8247 100644
@@ -545,8 +545,8 @@ struct ice_pf {
 	u32 msg_enable;
 	struct ice_ptp ptp;
 	struct tty_driver *ice_gnss_tty_driver;
-	struct tty_port gnss_tty_port;
-	struct gnss_serial *gnss_serial;
+	struct tty_port *gnss_tty_port[ICE_GNSS_TTY_MINOR_DEVICES];
+	struct gnss_serial *gnss_serial[ICE_GNSS_TTY_MINOR_DEVICES];
 	u16 num_rdma_msix;		/* Total MSIX vectors for RDMA driver */
 	u16 rdma_base_vector;
 
drivers/net/ethernet/intel/ice/ice_gnss.c +216 -26

329 lines not on this page · raw message

drivers/net/ethernet/intel/ice/ice_gnss.h +27 -3
index 9211adb2372c..f454dd1d9285 100644
@@ -1,5 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-/* Copyright (C) 2018-2021, Intel Corporation. */
+/* Copyright (C) 2021-2022, Intel Corporation. */
 
 #ifndef _ICE_GNSS_H_
 #define _ICE_GNSS_H_
@@ -8,14 +8,34 @@
 #include <linux/tty_flip.h>
 
 #define ICE_E810T_GNSS_I2C_BUS		0x2
+#define ICE_GNSS_TIMER_DELAY_TIME	(HZ / 10) /* 0.1 second per message */
+/* Create 2 minor devices, both using the same GNSS module. First one is RW,
+ * second one RO.
+ */
+#define ICE_GNSS_TTY_MINOR_DEVICES	2
+#define ICE_GNSS_TTY_WRITE_BUF		250
+#define ICE_MAX_I2C_DATA_SIZE		FIELD_MAX(ICE_AQC_I2C_DATA_SIZE_M)
+#define ICE_MAX_I2C_WRITE_BYTES		4
+
+/* u-blox ZED-F9T specific definitions */
 #define ICE_GNSS_UBX_I2C_BUS_ADDR	0x42
 /* Data length register is big endian */
 #define ICE_GNSS_UBX_DATA_LEN_H		0xFD
 #define ICE_GNSS_UBX_DATA_LEN_WIDTH	2
 #define ICE_GNSS_UBX_EMPTY_DATA		0xFF
-#define ICE_GNSS_TIMER_DELAY_TIME	(HZ / 10) /* 0.1 second per message */
-#define ICE_MAX_I2C_DATA_SIZE		FIELD_MAX(ICE_AQC_I2C_DATA_SIZE_M)
+/* For u-blox writes are performed without address so the first byte to write is
+ * passed as I2C addr parameter.
+ */
+#define ICE_GNSS_UBX_WRITE_BYTES	(ICE_MAX_I2C_WRITE_BYTES + 1)
 #define ICE_MAX_UBX_READ_TRIES		255
+#define ICE_MAX_UBX_ACK_READ_TRIES	4095
+
+struct gnss_write_buf {
+	struct list_head queue;
+	unsigned int size;
+	unsigned char *buf;
+};
+
 
 /**
  * struct gnss_serial - data used to initialize GNSS TTY port
@@ -25,6 +45,8 @@
  * @gnss_mutex: gnss_mutex used to protect GNSS serial operations
  * @kworker: kwork thread for handling periodic work
  * @read_work: read_work function for handling GNSS reads
+ * @write_work: write_work function for handling GNSS writes
+ * @queue: write buffers queue
  */
 struct gnss_serial {
 	struct ice_pf *back;
@@ -33,6 +55,8 @@ struct gnss_serial {
 	struct mutex gnss_mutex; /* protects GNSS serial structure */
 	struct kthread_worker *kworker;
 	struct kthread_delayed_work read_work;
+	struct kthread_work write_work;
+	struct list_head queue;
 };
 
 #if IS_ENABLED(CONFIG_TTY)
Signature · 6 lines
2.34.1

_______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
maintainer
#2 lore raw
In reply to Karol Kolacinski

On 6/23/2022 6:41 AM, Karol Kolacinski wrote:

<snip>

Quoted 15 lines
drivers/net/ethernet/intel/ice/ice_common.c +15 -0
+/**
+ * ice_aq_write_i2c
+ * @hw: pointer to the hw struct
+ * @topo_addr: topology address for a device to communicate with
+ * @bus_addr: 7-bit I2C bus address
+ * @addr: I2C memory address (I2C offset) with up to 16 bits
+ * @params: I2C parameters: bit [4] - I2C address type, bits [3:0] - data size to write (0-7 bytes)
+ * @data: pointer to data (0 to 4 bytes) to be written to the I2C device
+ * @cd: pointer to command details structure or NULL
+ *
+ * Write I2C (0x06E3)
+ *
+ * * Return:
+ * * 0             - Successful write to the i2c device
+ * * -EINVAL       - Data size greater than 4 bytes

drivers/net/ethernet/intel/ice/ice_common.c ice_aq_read_i2c(struct ice_hw *hw, struct ice_aqc_link_topo_addr topo_addr, · line 4885

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_common.c +10 -0
+ * * -EIO          - FW error
+ */
+int
+ice_aq_write_i2c(struct ice_hw *hw, struct ice_aqc_link_topo_addr topo_addr,
+		 u16 bus_addr, __le16 addr, u8 params, u8 *data,
+		 struct ice_sq_cd *cd)
+{
+	struct ice_aq_desc desc = { 0 };
+	struct ice_aqc_i2c *cmd;
+	unsigned int i;

../drivers/net/ethernet/intel/ice/ice_common.c: In function ‘ice_aq_write_i2c’:
../drivers/net/ethernet/intel/ice/ice_common.c:4885:15: warning: unused variable ‘i’ [-Wunused-variable]
unsigned int i;

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_common.c +10 -0
+	u8 data_size;
+
+	ice_fill_dflt_direct_cmd_desc(&desc, ice_aqc_opc_write_i2c);
+	cmd = &desc.params.read_write_i2c;
+
+	data_size = FIELD_GET(ICE_AQC_I2C_DATA_SIZE_M, params);
+
+	/* data_size limited to 4 */
+	if (data_size > 4)
+		return -EINVAL;

drivers/net/ethernet/intel/ice/ice_common.c ice_aq_read_i2c(struct ice_hw *hw, struct ice_aqc_link_topo_addr topo_addr, · line 4905

Quoted 10 lines
drivers/net/ethernet/intel/ice/ice_common.c +10 -0
+
+	cmd->i2c_bus_addr = cpu_to_le16(bus_addr);
+	cmd->topo_addr = topo_addr;
+	cmd->i2c_params = params;
+	cmd->i2c_addr = addr;
+
+	memcpy(cmd->i2c_data, data, data_size);
+
+	return ice_aq_send_cmd(hw, &desc, NULL, 0, cd);
+}

_______________________________________________
Intel-wired-lan mailing list
[email protected]
https://lists.osuosl.org/mailman/listinfo/intel-wired-lan