Skip to contentSkip to conversation

serial: stm32: make info structs static to avoid sparse warnings

PATCH In review Ben Dooks 2 participants 2 messages Jul 21, 2022 – Aug 11, 2022

Subsystems (2)
lore
Share & tools
lore

Ben Dooks

author
#0 lore raw

PATCH 1/1 serial: stm32: make info structs static to avoid sparse warnings

The info structs are local only to the stm32-usart.c driver and are triggering sparse warnings about being undecalred. Move these into the main driver code and make them static to avoid the following warnings:

drivers/tty/serial/stm32-usart.h:42:25: warning: symbol 'stm32f4_info' was not declared. Should it be static? drivers/tty/serial/stm32-usart.h:63:25: warning: symbol 'stm32f7_info' was not declared. Should it be static? drivers/tty/serial/stm32-usart.h:85:25: warning: symbol 'stm32h7_info' was not declared. Should it be static?

---
 drivers/tty/serial/stm32-usart.c | 69 ++++++++++++++++++++++++++++++++
 drivers/tty/serial/stm32-usart.h | 68 -------------------------------
 2 files changed, 69 insertions(+), 68 deletions(-)
drivers/tty/serial/stm32-usart.c +69 -0
index 0973b03eeeaa..01f1ab2c18c0 100644
@@ -35,6 +35,75 @@
 #include "serial_mctrl_gpio.h"
 #include "stm32-usart.h"
 
+
+/* Register offsets */
+static struct stm32_usart_info stm32f4_info = {
+	.ofs = {
+		.isr	= 0x00,
+		.rdr	= 0x04,
+		.tdr	= 0x04,
+		.brr	= 0x08,
+		.cr1	= 0x0c,
+		.cr2	= 0x10,
+		.cr3	= 0x14,
+		.gtpr	= 0x18,
+		.rtor	= UNDEF_REG,
+		.rqr	= UNDEF_REG,
+		.icr	= UNDEF_REG,
+	},
+	.cfg = {
+		.uart_enable_bit = 13,
+		.has_7bits_data = false,
+		.fifosize = 1,
+	}
+};
+
+static struct stm32_usart_info stm32f7_info = {
+	.ofs = {
+		.cr1	= 0x00,
+		.cr2	= 0x04,
+		.cr3	= 0x08,
+		.brr	= 0x0c,
+		.gtpr	= 0x10,
+		.rtor	= 0x14,
+		.rqr	= 0x18,
+		.isr	= 0x1c,
+		.icr	= 0x20,
+		.rdr	= 0x24,
+		.tdr	= 0x28,
+	},
+	.cfg = {
+		.uart_enable_bit = 0,
+		.has_7bits_data = true,
+		.has_swap = true,
+		.fifosize = 1,
+	}
+};
+
+static struct stm32_usart_info stm32h7_info = {
+	.ofs = {
+		.cr1	= 0x00,
+		.cr2	= 0x04,
+		.cr3	= 0x08,
+		.brr	= 0x0c,
+		.gtpr	= 0x10,
+		.rtor	= 0x14,
+		.rqr	= 0x18,
+		.isr	= 0x1c,
+		.icr	= 0x20,
+		.rdr	= 0x24,
+		.tdr	= 0x28,
+	},
+	.cfg = {
+		.uart_enable_bit = 0,
+		.has_7bits_data = true,
+		.has_swap = true,
+		.has_wakeup = true,
+		.has_fifo = true,
+		.fifosize = 16,
+	}
+};
+
 static void stm32_usart_stop_tx(struct uart_port *port);
 static void stm32_usart_transmit_chars(struct uart_port *port);
 static void __maybe_unused stm32_usart_console_putchar(struct uart_port *port, unsigned char ch);
drivers/tty/serial/stm32-usart.h +0 -68

74 lines not on this page · raw message

Signature · 1 line
2.35.1
maintainer
#1 lore raw
Quoted 8 lines · Ben Dooks

The info structs are local only to the stm32-usart.c driver and are triggering sparse warnings about being undecalred. Move these into the main driver code and make them static to avoid the following warnings:

drivers/tty/serial/stm32-usart.h:42:25: warning: symbol 'stm32f4_info' was not declared. Should it be static? drivers/tty/serial/stm32-usart.h:63:25: warning: symbol 'stm32f7_info' was not declared. Should it be static? drivers/tty/serial/stm32-usart.h:85:25: warning: symbol 'stm32h7_info' was not declared. Should it be static?

Right, I would go even further. There is no point in having a separate header. So could you move the whole content to .c?

Quoted 155 lines
---
  drivers/tty/serial/stm32-usart.c | 69 ++++++++++++++++++++++++++++++++
  drivers/tty/serial/stm32-usart.h | 68 -------------------------------
  2 files changed, 69 insertions(+), 68 deletions(-)
drivers/tty/serial/stm32-usart.c +69 -0
index 0973b03eeeaa..01f1ab2c18c0 100644
@@ -35,6 +35,75 @@
  #include "serial_mctrl_gpio.h"
  #include "stm32-usart.h"
 
+
+/* Register offsets */
+static struct stm32_usart_info stm32f4_info = {
+	.ofs = {
+		.isr	= 0x00,
+		.rdr	= 0x04,
+		.tdr	= 0x04,
+		.brr	= 0x08,
+		.cr1	= 0x0c,
+		.cr2	= 0x10,
+		.cr3	= 0x14,
+		.gtpr	= 0x18,
+		.rtor	= UNDEF_REG,
+		.rqr	= UNDEF_REG,
+		.icr	= UNDEF_REG,
+	},
+	.cfg = {
+		.uart_enable_bit = 13,
+		.has_7bits_data = false,
+		.fifosize = 1,
+	}
+};
+
+static struct stm32_usart_info stm32f7_info = {
+	.ofs = {
+		.cr1	= 0x00,
+		.cr2	= 0x04,
+		.cr3	= 0x08,
+		.brr	= 0x0c,
+		.gtpr	= 0x10,
+		.rtor	= 0x14,
+		.rqr	= 0x18,
+		.isr	= 0x1c,
+		.icr	= 0x20,
+		.rdr	= 0x24,
+		.tdr	= 0x28,
+	},
+	.cfg = {
+		.uart_enable_bit = 0,
+		.has_7bits_data = true,
+		.has_swap = true,
+		.fifosize = 1,
+	}
+};
+
+static struct stm32_usart_info stm32h7_info = {
+	.ofs = {
+		.cr1	= 0x00,
+		.cr2	= 0x04,
+		.cr3	= 0x08,
+		.brr	= 0x0c,
+		.gtpr	= 0x10,
+		.rtor	= 0x14,
+		.rqr	= 0x18,
+		.isr	= 0x1c,
+		.icr	= 0x20,
+		.rdr	= 0x24,
+		.tdr	= 0x28,
+	},
+	.cfg = {
+		.uart_enable_bit = 0,
+		.has_7bits_data = true,
+		.has_swap = true,
+		.has_wakeup = true,
+		.has_fifo = true,
+		.fifosize = 16,
+	}
+};
+
  static void stm32_usart_stop_tx(struct uart_port *port);
  static void stm32_usart_transmit_chars(struct uart_port *port);
  static void __maybe_unused stm32_usart_console_putchar(struct uart_port *port, unsigned char ch);
drivers/tty/serial/stm32-usart.h +0 -61
index ee69c203b926..0ec41a732c88 100644
@@ -38,74 +38,6 @@ struct stm32_usart_info {
 
  #define UNDEF_REG 0xff
 
-/* Register offsets */
-struct stm32_usart_info stm32f4_info = {
-	.ofs = {
-		.isr	= 0x00,
-		.rdr	= 0x04,
-		.tdr	= 0x04,
-		.brr	= 0x08,
-		.cr1	= 0x0c,
-		.cr2	= 0x10,
-		.cr3	= 0x14,
-		.gtpr	= 0x18,
-		.rtor	= UNDEF_REG,
-		.rqr	= UNDEF_REG,
-		.icr	= UNDEF_REG,
-	},
-	.cfg = {
-		.uart_enable_bit = 13,
-		.has_7bits_data = false,
-		.fifosize = 1,
-	}
-};
-
-struct stm32_usart_info stm32f7_info = {
-	.ofs = {
-		.cr1	= 0x00,
-		.cr2	= 0x04,
-		.cr3	= 0x08,
-		.brr	= 0x0c,
-		.gtpr	= 0x10,
-		.rtor	= 0x14,
-		.rqr	= 0x18,
-		.isr	= 0x1c,
-		.icr	= 0x20,
-		.rdr	= 0x24,
-		.tdr	= 0x28,
-	},
-	.cfg = {
-		.uart_enable_bit = 0,
-		.has_7bits_data = true,
-		.has_swap = true,
-		.fifosize = 1,
-	}
-};
-
-struct stm32_usart_info stm32h7_info = {
-	.ofs = {
-		.cr1	= 0x00,
-		.cr2	= 0x04,
-		.cr3	= 0x08,
-		.brr	= 0x0c,
-		.gtpr	= 0x10,
-		.rtor	= 0x14,
-		.rqr	= 0x18,
-		.isr	= 0x1c,
-		.icr	= 0x20,
-		.rdr	= 0x24,
-		.tdr	= 0x28,
-	},
-	.cfg = {
-		.uart_enable_bit = 0,
-		.has_7bits_data = true,

drivers/tty/serial/stm32-usart.h struct stm32_usart_info { · line 43

Quoted 10 lines
drivers/tty/serial/stm32-usart.h +0 -7
-		.has_swap = true,
-		.has_wakeup = true,
-		.has_fifo = true,
-		.fifosize = 16,
-	}
-};
-
  /* USART_SR (F4) / USART_ISR (F7) */
  #define USART_SR_PE		BIT(0)
  #define USART_SR_FE		BIT(1)

thanks,

Signature · 2 lines
js
suse labs