asus-wmi: Add support for RGB keyboards
Luke D. Jones
maintainercover asus-wmi: Add support for RGB keyboards
This is a patch series to add RGB support for ASUS laptops. The laptops with this RGB tend to be the TUF series of gamer laptops.
The first step is initial bringup of support using the multicolor LED API.
These types of keyboards implement a slightly more complex interface than just RGB control however - they also have modes with can be static LED, blinking, rainbow, color cycles, and more. They also have some custom animations that can play depending on device state, such as suspended playing a fancy colour cycle, or playing a "wave" animation.
Two of the patches add support for these features.
The last patch adds documentation in:Documentation/ABI/testing/sysfs-platform-asus-wmi
Some notes:
- this patch series obsoletes the previous RGB patches by myself
- it is not possible to add attribute groups to multicolor LED as they get overwritten by led_multicolor_groups in led_classdev_multicolor_register_ext.
- the methods for RGB control do not provide a way to fetch exisiting state, so these methods are WO.
- There is an existing asus::kbd_backlight, this provides a 4-step brightness to the RGB (off,low,med,high) individually to multicolor. I was unsure of the effect of adding a similar path so have used the asus::multicolour::kbd_backlight name to be clear about purpose. If the asus::kbd_backlight is off, then no RGB is shown at all.\
I'm hopeful that this patch series addresses all previous feedback related to the obsoleted patches.
Luke D. Jones (5):
asus-wmi: Add basic support for TUF laptop keyboard RGB
asus-wmi: Add support for TUF laptop keyboard RGB mode control
asus-wmi: Add support for TUF laptop keyboard states
asus-wmi: Document many of the undocumented API
asus-wmi: Convert all attr _show to use sysfs_emit
.../ABI/testing/sysfs-platform-asus-wmi | 50 ++++ drivers/platform/x86/asus-wmi.c | 263 +++++++++++++++++- include/linux/platform_data/x86/asus-wmi.h | 5 + 3 files changed, 311 insertions(+), 7 deletions(-)
--
2.37.1
Luke D. Jones
maintainerPATCH 1/5 asus-wmi: Add basic support for TUF laptop keyboard RGB
Adds support for TUF laptop RGB control via the multicolor LED API.
As this is the base essentials for adjusting the RGB, it sets the default mode of the keyboard to static. This overwrites the booted state of the keyboard.
--- drivers/platform/x86/asus-wmi.c | 89 ++++++++++++++++++++++ include/linux/platform_data/x86/asus-wmi.h | 3 + 2 files changed, 92 insertions(+)
drivers/platform/x86/asus-wmi.c +89 -0
@@ -25,6 +25,7 @@#include <linux/input/sparse-keymap.h> #include <linux/kernel.h> #include <linux/leds.h> +#include <linux/led-class-multicolor.h> #include <linux/module.h> #include <linux/pci.h> #include <linux/pci_hotplug.h>
@@ -190,6 +191,11 @@ struct fan_curve_data {u8 percents[FAN_CURVE_POINTS ]; }; +struct keyboard_rgb_led { +struct led_classdev_mc dev; +struct mc_subled subled_info[3 ];/* r g b */ +}; +struct asus_wmi {int dsts_id;int spec;
@@ -234,6 +240,9 @@ struct asus_wmi {bool dgpu_disable_available;bool dgpu_disable; +bool keyboard_rgb_mode_available; +struct keyboard_rgb_led keyboard_rgb_mode; +bool throttle_thermal_policy_available;u8 throttle_thermal_policy_mode;
@@ -1028,6 +1037,35 @@ static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev)return result &ASUS_WMI_DSTS_LIGHTBAR_MASK ; } +static int tuf_rgb_brightness_set (struct led_classdev *cdev, +enum led_brightness brightness) +{ +u8 r, g, b; +int err; +u32 ret; + +struct led_classdev_mc *mc_cdev =lcdev_to_mccdev (cdev); + +led_mc_calc_color_components (mc_cdev, brightness); + r = mc_cdev->subled_info[0 ].brightness; + g = mc_cdev->subled_info[1 ].brightness; + b = mc_cdev->subled_info[2 ].brightness; + +/* Writing out requires some defaults. This will overwrite boot mode */ + err =asus_wmi_evaluate_method3 (ASUS_WMI_METHODID_DEVS ,ASUS_WMI_DEVID_TUF_RGB_MODE , +1 |0 | (r <<16 ) | (g <<24 ), (b) |0 , &ret); +if (err) { +pr_err ("Unable to set TUF RGB data?\n" ); +return err; + } +return 0 ; +} + +static enum led_brightness tuf_rgb_brightness_get (struct led_classdev *cdev) +{ +return cdev->brightness; +} +static void asus_wmi_led_exit (struct asus_wmi *asus) {led_classdev_unregister (&asus->kbd_led);
@@ -1105,6 +1143,57 @@ static int asus_wmi_led_init(struct asus_wmi *asus) &asus->lightbar_led); } +if (asus_wmi_dev_is_present (asus,ASUS_WMI_DEVID_TUF_RGB_MODE )) { +struct led_classdev_mc *mc_cdev; +struct mc_subled *mc_led_info; +u8 brightness =127 ; + + mc_cdev = &asus->keyboard_rgb_mode.dev; + +/* +* asus::kbd_backlight still controls a base 3-level backlight and when +* it is on 0, the RGB is not visible at all. RGB should be treated as +* an additional step. +*/ + mc_cdev->led_cdev.name ="asus::multicolour::kbd_backlight" ; + mc_cdev->led_cdev.flags =LED_CORE_SUSPENDRESUME |LED_RETAIN_AT_SHUTDOWN ; + mc_cdev->led_cdev.brightness_set_blocking = tuf_rgb_brightness_set; + mc_cdev->led_cdev.brightness_get = tuf_rgb_brightness_get; + +/* Let the multicolour LED own the info */ + mc_led_info =devm_kmalloc_array ( + &asus->platform_device->dev, +3 , +sizeof (*mc_led_info), +GFP_KERNEL | __GFP_ZERO); + +if (!mc_led_info) +return -ENOMEM ; + + mc_led_info[0 ].color_index =LED_COLOR_ID_RED ; + mc_led_info[1 ].color_index =LED_COLOR_ID_GREEN ; + mc_led_info[2 ].color_index =LED_COLOR_ID_BLUE ; + +/* +* It's not possible to get last set data from device so set defaults +* to make it safe for a user to change either RGB or modes. We don't +* write these defaults to the device because they will overwrite a +* users last saved boot setting (in NVRAM). +*/ + mc_cdev->led_cdev.brightness = brightness; + mc_cdev->led_cdev.max_brightness = brightness; + mc_led_info[0 ].intensity = brightness; + mc_led_info[0 ].brightness = mc_cdev->led_cdev.brightness; + mc_led_info[1 ].brightness = mc_cdev->led_cdev.brightness; + mc_led_info[2 ].brightness = mc_cdev->led_cdev.brightness; +led_mc_calc_color_components (mc_cdev, brightness); + + mc_cdev->subled_info = mc_led_info; + mc_cdev->num_colors =3 ; + + rv =led_classdev_multicolor_register (&asus->platform_device->dev, mc_cdev); + } + error:if (rv)asus_wmi_led_exit (asus);
include/linux/platform_data/x86/asus-wmi.h +3 -0
@@ -98,6 +98,9 @@/* dgpu on/off */ #define ASUS_WMI_DEVID_DGPU 0x00090020 +/* TUF laptop RGB control */ +#define ASUS_WMI_DEVID_TUF_RGB_MODE 0x00100056 +/* DSTS masks */ #define ASUS_WMI_DSTS_STATUS_BIT 0x00000001#define ASUS_WMI_DSTS_UNKNOWN_BIT 0x00000002
Signature · 1 line
2.37.1
Re: [PATCH 1/5] asus-wmi: Add basic support for TUF laptop keyboard RGB
Quoted 4 lines · Luke D. Jones
Adds support for TUF laptop RGB control via the multicolor LED API.
As this is the base essentials for adjusting the RGB, it sets the
these are
...or...
essential
Quoted 2 lines
default mode of the keyboard to static. This overwrites the booted state of the keyboard.
...
Quoted 2 lines
#include <
linux/leds.h>
+#include <linux/led-class-multicolor.h>
Not sure about the ordering ('-' vs. 's') in locale C.
...
drivers/platform/x86/asus-wmi.c static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev) · line 1047
Quoted 9 lines
drivers/platform/x86/asus-wmi.c +8
-0+static int tuf_rgb_brightness_set (struct led_classdev *cdev, +enum led_brightness brightness) +{ +u8 r, g, b; +int err; +u32 ret; + +struct led_classdev_mc *mc_cdev =lcdev_to_mccdev (cdev);
No need to put blank lines in the definition block. Also it would be better to move the longest line to be first.
drivers/platform/x86/asus-wmi.c static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev) · line 1056
Quoted 8 lines
drivers/platform/x86/asus-wmi.c +8
-0+led_mc_calc_color_components (mc_cdev, brightness); + r = mc_cdev->subled_info[0 ].brightness; + g = mc_cdev->subled_info[1 ].brightness; + b = mc_cdev->subled_info[2 ].brightness; + +/* Writing out requires some defaults. This will overwrite boot mode */ + err =asus_wmi_evaluate_method3 (ASUS_WMI_METHODID_DEVS ,ASUS_WMI_DEVID_TUF_RGB_MODE , +1 |0 | (r <<16 ) | (g <<24 ), (b) |0 , &ret);
What the point in those ' | 0' additions?
drivers/platform/x86/asus-wmi.c static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev) · line 1058
Quoted 2 lines
drivers/platform/x86/asus-wmi.c +2
-0+if (err) { +pr_err ("Unable to set TUF RGB data?\n" );
Why not dev_err() ?
drivers/platform/x86/asus-wmi.c static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev) · line 1061
Quoted 3 lines
drivers/platform/x86/asus-wmi.c +3
-0+return err; + } +return 0 ;
return err;
Quoted 1 line
+}
...
drivers/platform/x86/asus-wmi.c static int asus_wmi_led_init(struct asus_wmi *asus) · line 1151
Quoted 6 lines
drivers/platform/x86/asus-wmi.c +5
-0+if (asus_wmi_dev_is_present (asus,ASUS_WMI_DEVID_TUF_RGB_MODE )) { +struct led_classdev_mc *mc_cdev; +struct mc_subled *mc_led_info; +u8 brightness =127 ; + mc_cdev = &asus->keyboard_rgb_mode.dev;
Join this with the definition above. It's fine if it's a bit longer than 80 characters.
drivers/platform/x86/asus-wmi.c static int asus_wmi_led_init(struct asus_wmi *asus) · line 1165
Quoted 13 lines
drivers/platform/x86/asus-wmi.c +13
-0+/* +* asus::kbd_backlight still controls a base 3-level backlight and when +* it is on 0, the RGB is not visible at all. RGB should be treated as +* an additional step. +*/ + mc_cdev->led_cdev.name ="asus::multicolour::kbd_backlight" ; + mc_cdev->led_cdev.flags =LED_CORE_SUSPENDRESUME |LED_RETAIN_AT_SHUTDOWN ; + mc_cdev->led_cdev.brightness_set_blocking = tuf_rgb_brightness_set; + mc_cdev->led_cdev.brightness_get = tuf_rgb_brightness_get; + +/* Let the multicolour LED own the info */ + mc_led_info = devm_kmalloc_array( + &asus->platform_device->dev,
With a temporary variable you may make this one line shorter and nicer looking
struct device *dev = &asus->platform_device->dev;
Quoted 19 lines
drivers/platform/x86/asus-wmi.c +19
-0+3 , +sizeof (*mc_led_info), + GFP_KERNEL | __GFP_ZERO); + +if (!mc_led_info) +return -ENOMEM ; + + mc_led_info[0 ].color_index =LED_COLOR_ID_RED ; + mc_led_info[1 ].color_index =LED_COLOR_ID_GREEN ; + mc_led_info[2 ].color_index =LED_COLOR_ID_BLUE ; + +/* +* It's not possible to get last set data from device so set defaults +* to make it safe for a user to change either RGB or modes. We don't +* write these defaults to the device because they will overwrite a +* users last saved boot setting (in NVRAM). +*/ + mc_cdev->led_cdev.brightness = brightness; + mc_cdev->led_cdev.max_brightness = brightness;
drivers/platform/x86/asus-wmi.c static int asus_wmi_led_init(struct asus_wmi *asus) · line 1194
Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10
-0+ mc_led_info[0 ].intensity = brightness; + mc_led_info[0 ].brightness = mc_cdev->led_cdev.brightness; + mc_led_info[1 ].brightness = mc_cdev->led_cdev.brightness; + mc_led_info[2 ].brightness = mc_cdev->led_cdev.brightness; +led_mc_calc_color_components (mc_cdev, brightness); + + mc_cdev->subled_info = mc_led_info; + mc_cdev->num_colors =3 ; + + rv =led_classdev_multicolor_register (&asus->platform_device->dev, mc_cdev);
This also becomes shorter.
Quoted 1 line
+ }
Signature · 2 lines
With Best Regards, Andy Shevchenko
Luke Jones
maintainerRe: [PATCH 1/5] asus-wmi: Add basic support for TUF laptop keyboard RGB
Hi Andy, thanks for the feedback:
Quoted 13 lines · Andy Shevchenko
Quoted 4 lines · Luke D. Jones
Adds support for TUF laptop RGB control via the multicolor LED API.
As this is the base essentials for adjusting the RGB, it sets the
these are
...or...
essentialQuoted 2 lines
default mode of the keyboard to static. This overwrites the booted state of the keyboard.
Quoted 7 lines
...
Quoted 2 lines
#include <
linux/leds.h>
+#include <linux/led-class-multicolor.h>Not sure about the ordering ('-' vs. 's') in locale C.
I used hid-playstation.c as a reference and followed that ordering.
Quoted 9 lines
...
Quoted 6 lines
+static int tuf_rgb_brightness_set(struct
led_classdev*cdev,
+ enumled_brightnessbrightness)
+{+ u8 r, g, b; + int err; + u32 ret;
Quoted 5 lines
Quoted 2 lines
+
+ structled_classdev_mc*mc_cdev=lcdev_to_mccdev(cdev);No need to put blank lines in the definition block. Also it would be better to move the longest line to be first.
Okay cool. Done.
Quoted 13 lines
Quoted 5 lines
+ led_mc_calc_color_components(mc_cdev, brightness); + r = mc_cdev->subled_info[0].brightness; + g = mc_cdev->subled_info[1].brightness; + b = mc_cdev->subled_info[2].brightness;Quoted 7 lines
+
+ /* Writing out requires some defaults. This will overwrite
boot mode */
+ err = asus_wmi_evaluate_method3(ASUS_WMI_METHODID_DEVS,ASUS_WMI_DEVID_TUF_RGB_MODE,
+ 1 | 0 | (r << 16) | (g << 24), (b) | 0,
&ret);
Quoted 1 line
What the point in those ' | 0' additions?
They were place-holders in testing that I forgot to change in the second patch which adds mode configuration :(
Should be "save | (mode << 8) | (r << 16) | (g << 24), (b) | (speed << 8), &ret);", two bytes.
Quoted 5 lines
Quoted 3 lines
+ if (err) {
+pr_err("Unable to set TUF RGB data?\n");Why not
dev_err()?
I didn't know about it? Is there an example or doc on its use?
Quoted 6 lines
Quoted 4 lines
+ return err;
+ }
+ return 0;return err;
Something like this then?
if (err) {
pr_err("Unable to set TUF RGB data?\n");
}return err;
If so, done.
Quoted 11 lines
Quoted 2 lines
+}
...
Quoted 5 lines
+ if (asus_wmi_dev_is_present(asus,
ASUS_WMI_DEVID_TUF_RGB_MODE)) {+ struct led_classdev_mc *mc_cdev; + struct mc_subled *mc_led_info; + u8 brightness = 127;
Quoted 4 lines
Quoted 1 line
+
mc_cdev=&asus->keyboard_rgb_mode.dev;Join this with the definition above. It's fine if it's a bit longer than 80 characters.
Done.
Quoted 21 lines
Quoted 12 lines
+ /*
+ *asus::kbd_backlightstill controls a base
3-level backlight and when
+ * it is on 0, the RGB is not visible at all. RGB
should be treated as
+ * an additional step.
+ */
+mc_cdev->led_cdev.name=
"asus::multicolour::kbd_backlight";
+mc_cdev->led_cdev.flags=LED_CORE_SUSPENDRESUME|LED_RETAIN_AT_SHUTDOWN;Quoted 8 lines
+
mc_cdev->led_cdev.brightness_set_blocking=tuf_rgb_brightness_set;
+mc_cdev->led_cdev.brightness_get=tuf_rgb_brightness_get;
+
+ /* Let the multicolour LED own the info */
+mc_led_info= devm_kmalloc_array(
+&asus->platform_device->dev,
Quoted 4 lines
With a temporary variable you may make this one line shorter and nicer looking
struct device *dev = &asus->platform_device->dev;
Done.
Quoted 37 lines
Quoted 24 lines
+ 3, + sizeof(*mc_led_info), + GFP_KERNEL | __GFP_ZERO); + + if (!mc_led_info) + return -ENOMEM; + + mc_led_info[0].color_index = LED_COLOR_ID_RED; + mc_led_info[1].color_index = LED_COLOR_ID_GREEN; + mc_led_info[2].color_index = LED_COLOR_ID_BLUE;+
+ /*
+ * It's not possible to get last set data from
device so set defaults
+ * to make it safe for a user to change either RGB
or modes. We don't
+ * write these defaults to the device because they
will overwrite a
+ * users last saved boot setting (in NVRAM).
+ */+ mc_cdev->led_cdev.brightness = brightness; + mc_cdev->led_cdev.max_brightness = brightness; + mc_led_info[0].intensity = brightness; + mc_led_info[0].brightness =Quoted 12 lines
mc_cdev->led_cdev.brightness;
+ mc_led_info[1].brightness =mc_cdev->led_cdev.brightness;
+ mc_led_info[2].brightness =mc_cdev->led_cdev.brightness;
+led_mc_calc_color_components(mc_cdev, brightness);
+
+mc_cdev->subled_info=mc_led_info;
+mc_cdev->num_colors= 3;
+
+ rv =led_classdev_multicolor_register(&asus->platform_device->dev, mc_cdev);
Quoted 1 line
This also becomes shorter.
Done.
Quoted 6 lines
Quoted 2 lines
+ }
--
With Best Regards,
Andy Shevchenko
Re: [PATCH 1/5] asus-wmi: Add basic support for TUF laptop keyboard RGB
Quoted 3 lines · Luke Jones
Quoted 1 line · Andy Shevchenko
On Fri, Aug 5, 2022 at 10:20 AM Luke D. Jones <[email protected]> wrote:
...
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
#include <
linux/leds.h>
+#include <linux/led-class-multicolor.h>Not sure about the ordering ('-' vs. 's') in locale C.
I used
hid-playstation.cas a reference and followed that ordering.
Try something like this:
LC_ALL=c sort
for these two lines and see if the ordering is the same.
...
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
+ if (err) {
+pr_err("Unable to set TUF RGB data?\n");Why not
dev_err()?I didn't know about it? Is there an example or doc on its use?
Thousands of examples in the kernel source tree. The point is if you have a device (instance) available, use it for messaging.
Quoted 6 lines
Quoted 5 lines
Quoted 3 lines
+ return err;
+ }
+ return 0;return err;
Quoted 8 lines
Something like this then?
if (err) { pr_err("Unable to set TUF RGB data?\n"); }return err;
If so, done.
No parentheses. Have you run checkpatch.pl?
Something like
if (err)
dev_err(...);return err;
Quoted 1 line
Quoted 1 line
Quoted 1 line
+}
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH 1/5] asus-wmi: Add basic support for TUF laptop keyboard RGB
Quoted 4 lines · Andy Shevchenko
Quoted 3 lines · Luke Jones
Quoted 1 line · Andy Shevchenko
On Fri, Aug 5, 2022 at 10:20 AM Luke D. Jones <[email protected]> wrote:
...
Quoted 10 lines
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
#include <
linux/leds.h>
+#include <linux/led-class-multicolor.h>Not sure about the ordering ('-' vs. 's') in locale C.
I used
hid-playstation.cas a reference and followed that ordering.Try something like this:
LC_ALL=c sort
Should be, of course,
LC_ALL=C sort
Quoted 1 line
for these two lines and see if the ordering is the same.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH 1/5] asus-wmi: Add basic support for TUF laptop keyboard RGB
In reply to Luke D. JonesHi
2022. augusztus 5., péntek 10:19 keltezéssel, Luke D. Jones <[email protected]> írta:
Quoted 37 lines
Adds support for TUF laptop RGB control via the multicolor LED API.
As this is the base essentials for adjusting the RGB, it sets the default mode of the keyboard to static. This overwrites the booted state of the keyboard.
Signed-off-by Luke D. Jones <[email protected]>--- drivers/platform/x86/asus-wmi.c | 89 ++++++++++++++++++++++ include/linux/platform_data/x86/asus-wmi.h | 3 + 2 files changed, 92 insertions(+)drivers/platform/x86/asus-wmi.c +6
-0@@ -25,6 +25,7 @@#include <linux/input/sparse-keymap.h> #include <linux/kernel.h> #include <linux/leds.h> +#include <linux/led-class-multicolor.h> #include <linux/module.h> #include <linux/pci.h> #include <linux/pci_hotplug.h> @@ -190,6 +191,11 @@ struct fan_curve_data {u8 percents[FAN_CURVE_POINTS ]; }; +struct keyboard_rgb_led { +struct led_classdev_mc dev; +struct mc_subled subled_info[3 ];/* r g b */ +}; +struct asus_wmi {int dsts_id;int spec;
drivers/platform/x86/asus-wmi.c struct asus_wmi { · line 243
Quoted 4 lines
drivers/platform/x86/asus-wmi.c +1
-0@@ -234,6 +240,9 @@ struct asus_wmi {bool dgpu_disable_available;bool dgpu_disable; +bool keyboard_rgb_mode_available;
I think this variable could be introduced in the next patch, it is not used in this one.
Quoted 27 lines
drivers/platform/x86/asus-wmi.c +20
-0+struct keyboard_rgb_led keyboard_rgb_mode; +bool throttle_thermal_policy_available;u8 throttle_thermal_policy_mode;@@ -1028,6 +1037,35 @@ static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev)return result &ASUS_WMI_DSTS_LIGHTBAR_MASK ; } +static int tuf_rgb_brightness_set (struct led_classdev *cdev, +enum led_brightness brightness) +{ +u8 r, g, b; +int err; +u32 ret; + +struct led_classdev_mc *mc_cdev =lcdev_to_mccdev (cdev); + +led_mc_calc_color_components (mc_cdev, brightness); + r = mc_cdev->subled_info[0 ].brightness; + g = mc_cdev->subled_info[1 ].brightness; + b = mc_cdev->subled_info[2 ].brightness; + +/* Writing out requires some defaults. This will overwrite boot mode */ + err =asus_wmi_evaluate_method3 (ASUS_WMI_METHODID_DEVS ,ASUS_WMI_DEVID_TUF_RGB_MODE , +1 |0 | (r <<16 ) | (g <<24 ), (b) |0 , &ret); +if (err) {
drivers/platform/x86/asus-wmi.c static enum led_brightness lightbar_led_get(struct led_classdev *led_cdev) · line 1067
Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10
-0+pr_err ("Unable to set TUF RGB data?\n" ); +return err; + } +return 0 ; +} + +static enum led_brightness tuf_rgb_brightness_get (struct led_classdev *cdev) +{ +return cdev->brightness; +}
If you can't query the brightness from the hardware, I think you can leave led_classdev::brightness_get to be NULL. This callback is only used from led_update_brightness() as far as I can see.
Quoted 22 lines
drivers/platform/x86/asus-wmi.c +15
-0+static void asus_wmi_led_exit (struct asus_wmi *asus) {led_classdev_unregister (&asus->kbd_led);@@ -1105,6 +1143,57 @@ static int asus_wmi_led_init(struct asus_wmi *asus) &asus->lightbar_led); } +if (asus_wmi_dev_is_present (asus,ASUS_WMI_DEVID_TUF_RGB_MODE )) { +struct led_classdev_mc *mc_cdev; +struct mc_subled *mc_led_info; +u8 brightness =127 ; + + mc_cdev = &asus->keyboard_rgb_mode.dev; + +/* +* asus::kbd_backlight still controls a base 3-level backlight and when +* it is on 0, the RGB is not visible at all. RGB should be treated as +* an additional step. +*/ + mc_cdev->led_cdev.name ="asus::multicolour::kbd_backlight" ; + mc_cdev->led_cdev.flags =LED_CORE_SUSPENDRESUME |LED_RETAIN_AT_SHUTDOWN ;
drivers/platform/x86/asus-wmi.c static int asus_wmi_led_init(struct asus_wmi *asus) · line 1169
Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10
-0+ mc_cdev->led_cdev.brightness_set_blocking = tuf_rgb_brightness_set; + mc_cdev->led_cdev.brightness_get = tuf_rgb_brightness_get; + +/* Let the multicolour LED own the info */ + mc_led_info =devm_kmalloc_array ( + &asus->platform_device->dev, +3 , +sizeof (*mc_led_info), +GFP_KERNEL | __GFP_ZERO); +
I am a bit confused as to why dynamic allocation is needed here. Haven't you already "allocated" the storage in keyboard_rgb_led::subled_info?
Quoted 13 lines
drivers/platform/x86/asus-wmi.c +13
-0+if (!mc_led_info) +return -ENOMEM ; + + mc_led_info[0 ].color_index =LED_COLOR_ID_RED ; + mc_led_info[1 ].color_index =LED_COLOR_ID_GREEN ; + mc_led_info[2 ].color_index =LED_COLOR_ID_BLUE ; + +/* +* It's not possible to get last set data from device so set defaults +* to make it safe for a user to change either RGB or modes. We don't +* write these defaults to the device because they will overwrite a +* users last saved boot setting (in NVRAM). +*/
drivers/platform/x86/asus-wmi.c static int asus_wmi_led_init(struct asus_wmi *asus) · line 1192
Quoted 10 lines
drivers/platform/x86/asus-wmi.c +10
-0+ mc_cdev->led_cdev.brightness = brightness; + mc_cdev->led_cdev.max_brightness = brightness; + mc_led_info[0 ].intensity = brightness; + mc_led_info[0 ].brightness = mc_cdev->led_cdev.brightness; + mc_led_info[1 ].brightness = mc_cdev->led_cdev.brightness; + mc_led_info[2 ].brightness = mc_cdev->led_cdev.brightness; +led_mc_calc_color_components (mc_cdev, brightness); + + mc_cdev->subled_info = mc_led_info; + mc_cdev->num_colors =3 ;
led_mc_calc_color_components() uses led_classdev_mc::num_colors, so I think it needs to be set before calling it. But that function sets the subled brightness based on the intensity, so it will overwrite the brightness values that have just been set.
Quoted 22 lines
drivers/platform/x86/asus-wmi.c +4
-0+ + rv =led_classdev_multicolor_register (&asus->platform_device->dev, mc_cdev); + } + error:if (rv)asus_wmi_led_exit (asus);include/linux/platform_data/x86/asus-wmi.h +3
-1@@ -98,6 +98,9 @@/* dgpu on/off */ #define ASUS_WMI_DEVID_DGPU 0x00090020 +/* TUF laptop RGB control */ +#define ASUS_WMI_DEVID_TUF_RGB_MODE 0x00100056 +/* DSTS masks */ #define ASUS_WMI_DSTS_STATUS_BIT 0x00000001#define ASUS_WMI_DSTS_UNKNOWN_BIT 0x00000002 --
Quoted 3 lines
2.37.1
Regards,
Barnabás Pőcze
Luke Jones
maintainerRe: [PATCH 1/5] asus-wmi: Add basic support for TUF laptop keyboard RGB
Hi Barnabás,
Thank you for taking the time to review
Quoted 47 lines · Barnabás Pőcze
Hi
2022. augusztus 5., péntek 10:19 keltezéssel, Luke D. Jones <[email protected]> írta:
Quoted 42 lines
Adds support for TUF laptop RGB control via the multicolor LED API.
As this is the base essentials for adjusting the RGB, it sets the default mode of the keyboard to static. This overwrites the booted state of the keyboard.
Signed-off-by Luke D. Jones <[email protected]>---
drivers/platform/x86/asus-wmi.c | 89 ++++++++++++++++++++++ include/linux/platform_data/x86/asus-wmi.h | 3 + 2 files changed, 92 insertions(+)diff --git
a/drivers/platform/x86/asus-wmi.cb/drivers/platform/x86/asus-wmi.c
index0e7fbed8a50d..33384e3321bb100644
---a/drivers/platform/x86/asus-wmi.c
+++b/drivers/platform/x86/asus-wmi.c
@@ -25,6 +25,7 @@
#include <linux/input/sparse-keymap.h>
#include <linux/kernel.h>
#include <linux/leds.h>
+#include <linux/led-class-multicolor.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/pci_hotplug.h>
@@ -190,6 +191,11 @@ structfan_curve_data{
u8 percents[FAN_CURVE_POINTS];
};+struct
keyboard_rgb_led{
+ structled_classdev_mcdev;
+ structmc_subledsubled_info[3]; /* r g b */
+};
+
structasus_wmi{
intdsts_id;
int spec;
@@ -234,6 +240,9 @@ structasus_wmi{
booldgpu_disable_available;
booldgpu_disable;
Quoted 4 lines
Quoted 1 line
+ bool
keyboard_rgb_mode_available;I think this variable could be introduced in the next patch, it is not used in this one.
Thank you for spotting this. I must have missed it when I split the patches.
Quoted 43 lines
Quoted 34 lines
+ struct
keyboard_rgb_ledkeyboard_rgb_mode;
+
boolthrottle_thermal_policy_available;
u8throttle_thermal_policy_mode;@@ -1028,6 +1037,35 @@ static enum
led_brightnesslightbar_led_get(struct led_classdev *led_cdev)
return result &ASUS_WMI_DSTS_LIGHTBAR_MASK;
}+static int tuf_rgb_brightness_set(struct
led_classdev*cdev,
+ enumled_brightnessbrightness)
+{
+ u8 r, g, b;
+ int err;
+ u32 ret;
+
+ structled_classdev_mc*mc_cdev=lcdev_to_mccdev(cdev);
+
+led_mc_calc_color_components(mc_cdev, brightness);
+ r = mc_cdev->subled_info[0].brightness;
+ g = mc_cdev->subled_info[1].brightness;
+ b = mc_cdev->subled_info[2].brightness;
+
+ /* Writing out requires some defaults. This will overwrite boot
mode */
+ err = asus_wmi_evaluate_method3(ASUS_WMI_METHODID_DEVS,ASUS_WMI_DEVID_TUF_RGB_MODE,
+ 1 | 0 | (r << 16) | (g << 24), (b) | 0, &ret);
+ if (err) {
+pr_err("Unable to set TUF RGB data?\n");
+ return err;
+ }Quoted 8 lines
+ return 0;
+}
+
+static enumled_brightnesstuf_rgb_brightness_get(structled_classdev*cdev)
+{
+ returncdev->brightness;
+}
Quoted 4 lines
If you can't query the brightness from the hardware, I think you can leave
led_classdev::brightness_getto beNULL. This callback is only used fromled_update_brightness()as far as I can see.
I did wonder about this. Thanks, I've nulled it.
Quoted 39 lines
Quoted 30 lines
+
static voidasus_wmi_led_exit(struct asus_wmi *asus)
{
led_classdev_unregister(&asus->kbd_led);
@@ -1105,6 +1143,57 @@ static int asus_wmi_led_init(structasus_wmi
*asus)
&asus->lightbar_led);
}+ if (
asus_wmi_dev_is_present(asus, ASUS_WMI_DEVID_TUF_RGB_MODE)) {
+ structled_classdev_mc*mc_cdev;
+ structmc_subled*mc_led_info;
+ u8 brightness = 127;
+
+mc_cdev=&asus->keyboard_rgb_mode.dev;
+
+ /*
+ *asus::kbd_backlightstill controls a base 3-level backlight
and when
+ * it is on 0, the RGB is not visible at all. RGB should be
treated as
+ * an additional step.
+ */
+mc_cdev->led_cdev.name= "asus::multicolour::kbd_backlight";
+mc_cdev->led_cdev.flags=LED_CORE_SUSPENDRESUME|LED_RETAIN_AT_SHUTDOWN;
+mc_cdev->led_cdev.brightness_set_blocking=tuf_rgb_brightness_set;
+mc_cdev->led_cdev.brightness_get=tuf_rgb_brightness_get;Quoted 8 lines
+
+ /* Let the multicolour LED own the info */
+mc_led_info= devm_kmalloc_array(
+&asus->platform_device->dev,
+ 3,
+sizeof(*mc_led_info),
+GFP_KERNEL|__GFP_ZERO);
+
Quoted 2 lines
I am a bit confused as to why dynamic allocation is needed here. Haven't you already "allocated" the storage in
keyboard_rgb_led::subled_info?
Honestly, I write rust 90% of the time which is quite clear on these things, so here I wasn't very sure about what to do - I read the hid-playstation.c and it had something similar so I used it and completely forgot about the struct allocation.
I've updated to struct mc_subled *mc_led_info = asus->keyboard_rgb_mode.subled_info; and removed the dynamic alloc.
Quoted 29 lines
Quoted 20 lines
+ if (!mc_led_info)
+ return-ENOMEM;
+
+ mc_led_info[0].color_index =LED_COLOR_ID_RED;
+ mc_led_info[1].color_index =LED_COLOR_ID_GREEN;
+ mc_led_info[2].color_index =LED_COLOR_ID_BLUE;
+
+ /*
+ * It's not possible to get last set data from device so set
defaults
+ * to make it safe for a user to change either RGB or modes. We
don't
+ * write these defaults to the device because they will
overwrite a
+ * users last saved boot setting (in NVRAM).
+ */
+mc_cdev->led_cdev.brightness= brightness;
+mc_cdev->led_cdev.max_brightness= brightness;Quoted 8 lines
+ mc_led_info[0].intensity = brightness;
+ mc_led_info[0].brightness =mc_cdev->led_cdev.brightness;
+ mc_led_info[1].brightness =mc_cdev->led_cdev.brightness;
+ mc_led_info[2].brightness =mc_cdev->led_cdev.brightness;
+led_mc_calc_color_components(mc_cdev, brightness);
+
+mc_cdev->subled_info=mc_led_info;
+mc_cdev->num_colors= 3;
Quoted 4 lines
led_mc_calc_color_components()usesled_classdev_mc::num_colors, so I think it needs to be set before calling it. But that function sets the subled brightness based on the intensity, so it will overwrite the brightness values that have just been set.
Ah thanks, I don't think I understood that before. I've removed mc_led_info[i].brightness setting now.
Quoted 33 lines
Quoted 19 lines
+
+ rv =led_classdev_multicolor_register(&asus->platform_device->dev, mc_cdev);
+ }
+
error:
if (rv)
asus_wmi_led_exit(asus);
diff --gita/include/linux/platform_data/x86/asus-wmi.hb/include/linux/platform_data/x86/asus-wmi.h
indexa571b47ff362..d63c9945a17d100644
---a/include/linux/platform_data/x86/asus-wmi.h
+++b/include/linux/platform_data/x86/asus-wmi.h
@@ -98,6 +98,9 @@
/* dgpu on/off */
#defineASUS_WMI_DEVID_DGPU0x00090020Quoted 10 lines
+/* TUF laptop RGB control */
+#defineASUS_WMI_DEVID_TUF_RGB_MODE0x00100056
+
/* DSTS masks */
#defineASUS_WMI_DSTS_STATUS_BIT0x00000001
#defineASUS_WMI_DSTS_UNKNOWN_BIT0x00000002
--
2.37.1Regards,
Barnabás Pőcze
Luke D. Jones
maintainerPATCH 2/5 asus-wmi: Add support for TUF laptop keyboard RGB mode control
In reply to Luke D. JonesAdds support for TUF laptop RGB mode control.
Two paths are added:
- /sys/devices/platform/asus-nb-wmi/kernel_rgb_mode
- /sys/devices/platform/asus-nb-wmi/kernel_rgb_mode_index
--- drivers/platform/x86/asus-wmi.c | 86 +++++++++++++++++++++++++++++++++ 1 file changed, 86 insertions(+)
drivers/platform/x86/asus-wmi.c +86 -0
@@ -118,6 +118,9 @@ static const char * const ashs_ids[] = { "ATK4001", "ATK4002", NULL };static int throttle_thermal_policy_write (struct asus_wmi *); +static int tuf_rgb_brightness_set (struct led_classdev *cdev, +enum led_brightness brightness); +static bool ashs_present (void ) {int i =0 ;
@@ -194,6 +197,9 @@ struct fan_curve_data {struct keyboard_rgb_led {struct led_classdev_mc dev;struct mc_subled subled_info[3 ];/* r g b */ +u8 save; +u8 mode; +u8 speed; };struct asus_wmi {
@@ -743,6 +749,72 @@ static ssize_t egpu_enable_store(struct device *dev,static DEVICE_ATTR_RW (egpu_enable); +/* TUF Laptop Keyboard RGB Modes **********************************************/ +static int keyboard_rgb_mode_check_present (struct asus_wmi *asus) +{ +u32 result; +int err; + + asus->keyboard_rgb_mode_available = false; + + err =asus_wmi_get_devstate (asus,ASUS_WMI_DEVID_TUF_RGB_MODE , &result); +if (err) { +if (err == -ENODEV ) +return 0 ; +return err; + } + +if (result &ASUS_WMI_DSTS_PRESENCE_BIT ) { + asus->keyboard_rgb_mode_available = true; + } + +return 0 ; +} + +static ssize_t keyboard_rgb_mode_store (struct device *device, +struct device_attribute *attr, +const char *buf,size_t count) +{ +u8 save, mode, speed; +int err; + +struct asus_wmi *asus =dev_get_drvdata (device); +struct led_classdev *cdev = &asus->keyboard_rgb_mode.dev.led_cdev; + +if (sscanf (buf,"%hhd %hhd %hhd" , &save, &mode, &speed) !=3 ) +return -EINVAL ; + + asus->keyboard_rgb_mode.save = save >0 ?1 :0 ; + +/* These are the known usable modes across all TUF/ROG */ + asus->keyboard_rgb_mode.mode = mode <12 && mode !=9 ? mode :0x0a ; + +if (speed ==0 ) + asus->keyboard_rgb_mode.speed =0xe1 ; +else if (speed ==1 ) + asus->keyboard_rgb_mode.speed =0xeb ; +else if (speed ==2 ) + asus->keyboard_rgb_mode.speed =0xf5 ; +else + asus->keyboard_rgb_mode.speed =0xeb ; + + err =tuf_rgb_brightness_set (cdev, cdev->brightness); +if (err) +return err; +return 0 ; +} + +static DEVICE_ATTR_WO (keyboard_rgb_mode); + +static ssize_t keyboard_rgb_mode_index_show (struct device *device, +struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%s\n" ,"save mode speed\n" ); +} + +static DEVICE_ATTR_RO (keyboard_rgb_mode_index); +/* Battery ********************************************************************/ /* The battery maximum charging percentage */
@@ -1180,6 +1252,9 @@ static int asus_wmi_led_init(struct asus_wmi *asus)* write these defaults to the device because they will overwrite a * users last saved boot setting (in NVRAM). */ + asus->keyboard_rgb_mode.save =1 ; + asus->keyboard_rgb_mode.mode =0 ; + asus->keyboard_rgb_mode.speed =1 ; mc_cdev->led_cdev.brightness = brightness; mc_cdev->led_cdev.max_brightness = brightness; mc_led_info[0 ].intensity = brightness;
@@ -3347,6 +3422,8 @@ static struct attribute *platform_attributes[] = { &dev_attr_touchpad.attr, &dev_attr_egpu_enable.attr, &dev_attr_dgpu_disable.attr, + &dev_attr_keyboard_rgb_mode.attr, + &dev_attr_keyboard_rgb_mode_index.attr, &dev_attr_lid_resume.attr, &dev_attr_als_enable.attr, &dev_attr_fan_boost_mode.attr,
@@ -3377,6 +3454,10 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj, ok = asus->egpu_enable_available; else if (attr == &dev_attr_dgpu_disable.attr) ok = asus->dgpu_disable_available; + else if (attr == &dev_attr_keyboard_rgb_mode.attr) + ok = asus->keyboard_rgb_mode_available; + else if (attr == &dev_attr_keyboard_rgb_mode_index.attr) + ok = asus->keyboard_rgb_mode_available; else if (attr == &dev_attr_fan_boost_mode.attr) ok = asus->fan_boost_mode_available; else if (attr == &dev_attr_throttle_thermal_policy.attr)
@@ -3646,6 +3727,10 @@ static int asus_wmi_add(struct platform_device *pdev)if (err) goto fail_dgpu_disable; + err =keyboard_rgb_mode_check_present (asus); +if (err) + goto fail_keyboard_rgb_mode; + err =fan_boost_mode_check_present (asus);if (err) goto fail_fan_boost_mode;
@@ -3760,6 +3845,7 @@ static int asus_wmi_add(struct platform_device *pdev) fail_fan_boost_mode: fail_egpu_enable: fail_dgpu_disable: +fail_keyboard_rgb_mode: fail_platform: fail_panel_od:kfree (asus);
Signature · 1 line
2.37.1
Re: [PATCH 2/5] asus-wmi: Add support for TUF laptop keyboard RGB mode control
Quoted 6 lines · Luke D. Jones
Adds support for TUF laptop RGB mode control.
Two paths are added:
-/sys/devices/platform/asus-nb-wmi/kernel_rgb_mode
-/sys/devices/platform/asus-nb-wmi/kernel_rgb_mode_index
...
Quoted 7 lines
drivers/platform/x86/asus-wmi.c +7
-0+static int keyboard_rgb_mode_check_present (struct asus_wmi *asus) +{ +u32 result; +int err; + + asus->keyboard_rgb_mode_available = false; +
drivers/platform/x86/asus-wmi.c static ssize_t egpu_enable_store(struct device *dev,
Quoted 10 lines
drivers/platform/x86/asus-wmi.c +9
-0+ err =asus_wmi_get_devstate (asus,ASUS_WMI_DEVID_TUF_RGB_MODE , &result); +if (err) { +if (err == -ENODEV ) +return 0 ; +return err; + } +if (result &ASUS_WMI_DSTS_PRESENCE_BIT ) { + asus->keyboard_rgb_mode_available = true; + }
{} are not needed (except if they will be utilized in the next patches in the series).
Quoted 2 lines
(quoted diff) +2
-0+ return 0; +}
...
drivers/platform/x86/asus-wmi.c static ssize_t egpu_enable_store(struct device *dev, · line 785
Quoted 2 lines
drivers/platform/x86/asus-wmi.c +2
-0+if (sscanf (buf,"%hhd %hhd %hhd" , &save, &mode, &speed) !=3 ) +return -EINVAL ;
Usually we have three separate nodes for that, but they are kinda hidden in one driver, so I don't care much.
...
Quoted 1 line
+
asus->keyboard_rgb_mode.save= save > 0 ? 1 : 0;
So, it's actually boolean.
You may write it as
...save = !!save;
drivers/platform/x86/asus-wmi.c static ssize_t egpu_enable_store(struct device *dev,
Quoted 12 lines
drivers/platform/x86/asus-wmi.c +11
-0+/* These are the known usable modes across all TUF/ROG */ + asus->keyboard_rgb_mode.mode = mode <12 && mode !=9 ? mode :0x0a ; + +if (speed ==0 ) + asus->keyboard_rgb_mode.speed =0xe1 ; +else if (speed ==1 ) + asus->keyboard_rgb_mode.speed =0xeb ; +else if (speed ==2 ) + asus->keyboard_rgb_mode.speed =0xf5 ; +else + asus->keyboard_rgb_mode.speed =0xeb ;
So the 1 is default then, why not use switch-case to show this explicitly?
switch (speed) {
case 0:
...
break;
case 1:
default:
...
break;
case 2:
... break;
}
Yes, it's longer, but I think it's cleaner.
drivers/platform/x86/asus-wmi.c static ssize_t egpu_enable_store(struct device *dev, · line 804
Quoted 4 lines
drivers/platform/x86/asus-wmi.c +4
-0+ err =tuf_rgb_brightness_set (cdev, cdev->brightness); +if (err) +return err; +return 0 ;
return tuf_rgb_brightness_set(...);
Quoted 1 line
+}
Signature · 2 lines
With Best Regards, Andy Shevchenko
Luke Jones
maintainerRe: [PATCH 2/5] asus-wmi: Add support for TUF laptop keyboard RGB mode control
Hi Andy,
Quoted 25 lines · Andy Shevchenko
Quoted 6 lines · Luke D. Jones
Adds support for TUF laptop RGB mode control.
Two paths are added:
-/sys/devices/platform/asus-nb-wmi/kernel_rgb_mode
-/sys/devices/platform/asus-nb-wmi/kernel_rgb_mode_index...
Quoted 14 lines
+static int
keyboard_rgb_mode_check_present(struct asus_wmi *asus)+{
+ u32 result;
+ int err;
+
+asus->keyboard_rgb_mode_available= false;
+
+ err = asus_wmi_get_devstate(asus,ASUS_WMI_DEVID_TUF_RGB_MODE, &result);
+ if (err) {
+ if (err ==-ENODEV)
+ return 0;
+ return err;
+ }
Quoted 6 lines
Quoted 3 lines
+ if (result &
ASUS_WMI_DSTS_PRESENCE_BIT) {
+asus->keyboard_rgb_mode_available= true;
+ }{} are not needed (except if they will be utilized in the next patches in the series).
I've usually been pretty good at catching these. I must not have run the patch check script on this one.
Fixed.
Quoted 4 lines
Quoted 3 lines
+ return 0;
+}
Quoted 8 lines
...
Quoted 3 lines
+ if (
sscanf(buf, "%hhd %hhd %hhd", &save, &mode, &speed)!=
3)
+ return-EINVAL;Usually we have three separate nodes for that, but they are kinda hidden in one driver, so I don't care much.
I don't really understand what you mean sorry.
Quoted 10 lines
...
Quoted 1 line
+
asus->keyboard_rgb_mode.save= save > 0 ? 1 : 0;So, it's actually boolean.
You may write it as
...save = !!save;
Err okay. Done.
Quoted 27 lines
Quoted 12 lines
+ /* These are the known usable modes across all TUF/ROG */
+asus->keyboard_rgb_mode.mode= mode < 12 && mode != 9 ?
mode :0x0a;
+
+ if (speed == 0)
+asus->keyboard_rgb_mode.speed=0xe1;
+ else if (speed == 1)
+asus->keyboard_rgb_mode.speed=0xeb;
+ else if (speed == 2)
+asus->keyboard_rgb_mode.speed=0xf5;Quoted 2 lines
+ else
+asus->keyboard_rgb_mode.speed=0xeb;So the 1 is default then, why not use switch-case to show this explicitly?
switch (speed) {
case 0:... break; case 1: default: ... break; case 2: ...
Quoted 4 lines
break;
}Yes, it's longer, but I think it's cleaner.
Agreed. Done.
Quoted 7 lines
Quoted 5 lines
+ err =
tuf_rgb_brightness_set(cdev, cdev->brightness);
+ if (err)
+ return err;
+ return 0;return
tuf_rgb_brightness_set(...);
This causes a hang (waiting for return somewhere?) if I don't return count. Especially true if the return is 0.
Quoted 6 lines
Quoted 2 lines
+}
--
With Best Regards,
Andy Shevchenko
Re: [PATCH 2/5] asus-wmi: Add support for TUF laptop keyboard RGB mode control
Quoted 3 lines · Luke Jones
Quoted 1 line · Andy Shevchenko
On Fri, Aug 5, 2022 at 10:20 AM Luke D. Jones <[email protected]> wrote:
...
Quoted 8 lines
Quoted 6 lines
Quoted 3 lines
+ if (
sscanf(buf, "%hhd %hhd %hhd", &save, &mode, &speed)!=
3)
+ return-EINVAL;Usually we have three separate nodes for that, but they are kinda hidden in one driver, so I don't care much.
I don't really understand what you mean sorry.
Each value is in a separate sysfs "file" (we call it "sysfs node"), but it seems Pavel proposed a better solution so LED framework has something to offer you.
...
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
+ /* These are the known usable modes across all TUF/ROG */
+asus->keyboard_rgb_mode.mode= mode < 12 && mode != 9 ?
mode :0x0a;
This also can be improved
if (mode >= 12 || mode == 9)
...mode = 10;
else
...mode = mode;Or, if it's important, switch all above to be hexadecimal constants.
...
Quoted 9 lines
Quoted 6 lines
Quoted 4 lines
+ err =
tuf_rgb_brightness_set(cdev, cdev->brightness);
+ if (err)
+ return err;
+ return 0;return
tuf_rgb_brightness_set(...);This causes a hang (waiting for return somewhere?) if I don't return count. Especially true if the return is 0.
I didn't get this, because what I suggested is an equivalent to the above 4 lines.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Luke D. Jones
maintainerPATCH 3/5 asus-wmi: Add support for TUF laptop keyboard states
In reply to Luke D. JonesAdds support for the TUF series laptop power states.
Adds two paths:
- /sys/devices/platform/asus-nb-wmi/keyboard_rgb_state
- /sys/devices/platform/asus-nb-wmi/keyboard_rgb_state_index
--- drivers/platform/x86/asus-wmi.c | 74 ++++++++++++++++++++++ include/linux/platform_data/x86/asus-wmi.h | 2 + 2 files changed, 76 insertions(+)
drivers/platform/x86/asus-wmi.c +74 -0
@@ -246,6 +246,7 @@ struct asus_wmi {bool dgpu_disable_available;bool dgpu_disable; +bool keyboard_rgb_state_available;bool keyboard_rgb_mode_available;struct keyboard_rgb_led keyboard_rgb_mode;
@@ -815,6 +816,68 @@ static ssize_t keyboard_rgb_mode_index_show(struct device *device,static DEVICE_ATTR_RO (keyboard_rgb_mode_index); +/* TUF Laptop Keyboard RGB States *********************************************/ +static int keyboard_rgb_state_check_present (struct asus_wmi *asus) +{ +u32 result; +int err; + + asus->keyboard_rgb_state_available = false; + + err =asus_wmi_get_devstate (asus,ASUS_WMI_DEVID_TUF_RGB_STATE , &result); +if (err) { +if (err == -ENODEV ) +return 0 ; +return err; + } + +if (result &ASUS_WMI_DSTS_PRESENCE_BIT ) + asus->keyboard_rgb_state_available = true; + +return 0 ; +} + +static ssize_t keyboard_rgb_state_store (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +u8 flags, save, boot, awake, sleep, keyboard; +int err; +u32 ret; + + flags =0 ; +if (sscanf (buf,"%hhd %hhd %hhd %hhd %hhd" , &save, &boot, &awake, &sleep, &keyboard) !=5 ) +return -EINVAL ; + + save = save ==0 ?0x0100 :0x0000 ; +if (boot) + flags |=0x02 ; +if (awake) + flags |=0x08 ; +if (sleep) + flags |=0x20 ; +if (keyboard) + flags |=0x80 ; + + err =asus_wmi_evaluate_method3 (ASUS_WMI_METHODID_DEVS , +ASUS_WMI_DEVID_TUF_RGB_STATE ,0xBD | save | (flags <<16 ),0 , &ret); +if (err) +return err; + +return count; +} + +static DEVICE_ATTR_WO (keyboard_rgb_state); + +static ssize_t keyboard_rgb_state_index_show (struct device *device, +struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%s\n" ,"save boot awake sleep keyboard\n" ); +} + +static DEVICE_ATTR_RO (keyboard_rgb_state_index); +/* Battery ********************************************************************/ /* The battery maximum charging percentage */
@@ -3424,6 +3487,8 @@ static struct attribute *platform_attributes[] = { &dev_attr_dgpu_disable.attr, &dev_attr_keyboard_rgb_mode.attr, &dev_attr_keyboard_rgb_mode_index.attr, + &dev_attr_keyboard_rgb_state.attr, + &dev_attr_keyboard_rgb_state_index.attr, &dev_attr_lid_resume.attr, &dev_attr_als_enable.attr, &dev_attr_fan_boost_mode.attr,
@@ -3458,6 +3523,10 @@ static umode_t asus_sysfs_is_visible(struct kobject *kobj, ok = asus->keyboard_rgb_mode_available; else if (attr == &dev_attr_keyboard_rgb_mode_index.attr) ok = asus->keyboard_rgb_mode_available; + else if (attr == &dev_attr_keyboard_rgb_state.attr) + ok = asus->keyboard_rgb_state_available; + else if (attr == &dev_attr_keyboard_rgb_state_index.attr) + ok = asus->keyboard_rgb_state_available; else if (attr == &dev_attr_fan_boost_mode.attr) ok = asus->fan_boost_mode_available; else if (attr == &dev_attr_throttle_thermal_policy.attr)
@@ -3731,6 +3800,10 @@ static int asus_wmi_add(struct platform_device *pdev)if (err) goto fail_keyboard_rgb_mode; + err =keyboard_rgb_state_check_present (asus); +if (err) + goto fail_keyboard_rgb_state; + err =fan_boost_mode_check_present (asus);if (err) goto fail_fan_boost_mode;
@@ -3846,6 +3919,7 @@ static int asus_wmi_add(struct platform_device *pdev) fail_egpu_enable: fail_dgpu_disable: fail_keyboard_rgb_mode: +fail_keyboard_rgb_state: fail_platform: fail_panel_od:kfree (asus);
include/linux/platform_data/x86/asus-wmi.h +2 -0
@@ -100,6 +100,8 @@/* TUF laptop RGB control */ #define ASUS_WMI_DEVID_TUF_RGB_MODE 0x00100056 +/* TUF laptop RGB state control */ +#define ASUS_WMI_DEVID_TUF_RGB_STATE 0x00100057/* DSTS masks */ #define ASUS_WMI_DSTS_STATUS_BIT 0x00000001
Signature · 1 line
2.37.1
Re: [PATCH 3/5] asus-wmi: Add support for TUF laptop keyboard states
Hi!
Quoted 4 lines
Adds two paths:
-/sys/devices/platform/asus-nb-wmi/keyboard_rgb_state
-/sys/devices/platform/asus-nb-wmi/keyboard_rgb_state_index
Patches 2-3 -- we already have pattern trigger. This should use it...
Best regards,
Pavel
Signature · 1 line
People of Russia, stop Putin before his war on Ukraine escalates.
Luke Jones
maintainerRe: [PATCH 3/5] asus-wmi: Add support for TUF laptop keyboard states
Hi Pavel,
Quoted 7 lines · Pavel Machek
Hi!
Quoted 4 lines
Adds two paths:
-/sys/devices/platform/asus-nb-wmi/keyboard_rgb_state
-/sys/devices/platform/asus-nb-wmi/keyboard_rgb_state_indexPatches 2-3 -- we already have pattern trigger. This should use it...
Can you please provide more information? I'd be happy to use it, but because I do this in my free time I don't have the best knowledge of helpful stuff that already exists - so far I've been learning about stuff like this when someone like yourself brings it up, otherwise I try to follow existing code patterns in the source file.
Many thanks,
Luke.
Quoted 5 lines
Best regards,
Pavel
--
People of Russia, stop Putin before his war on Ukraine escalates.
Luke Jones
maintainerRe: [PATCH 3/5] asus-wmi: Add support for TUF laptop keyboard states
In reply to Pavel MachekHi Pavel,
I'm sorry but can you direct me to a source file or other that shows use of "pattern trigger". I don't know what this means or what to look for. From your response it seems I should certainly be using it.
I've finished with all the feedback I've received so far, and this is the last piece.
Kind regards,
Luke.
Quoted 12 lines · Pavel Machek
Hi!
Quoted 4 lines
Adds two paths:
-/sys/devices/platform/asus-nb-wmi/keyboard_rgb_state
-/sys/devices/platform/asus-nb-wmi/keyboard_rgb_state_indexPatches 2-3 -- we already have pattern trigger. This should use it...
Best regards,
Pavel
--
People of Russia, stop Putin before his war on Ukraine escalates.
Re: [PATCH 3/5] asus-wmi: Add support for TUF laptop keyboard states
Hi!
Quoted 3 lines
I'm sorry but can you direct me to a source file or other that shows use of "pattern trigger". I don't know what this means or what to look for. From your response it seems I should certainly be using it.
Trigger is at drivers/leds/trigger/ledtrig-pattern.c , you'd want to do something similar to drivers/leds/rgb/leds-qcom-lpg.c .
Quoted 2 lines
I've finished with all the feedback I've received so far, and this is the last piece.
Actually... you may want to submit version without patterns at first. It will be easier to review.
Best regards,
Pavel
Signature · 1 line
People of Russia, stop Putin before his war on Ukraine escalates.
Luke Jones
maintainerRe: [PATCH 3/5] asus-wmi: Add support for TUF laptop keyboard states
Quoted 10 lines · Pavel Machek
Hi!
Quoted 5 lines
I'm sorry but can you direct me to a source file or other that shows use of
"pattern trigger". I don't know what this means or what to look for. From
your response it seems I should certainly be using it.Trigger is at
drivers/leds/trigger/ledtrig-pattern.c, you'd want to do something similar todrivers/leds/rgb/leds-qcom-lpg.c.
I think we lost something in communication. This looks like it is all done in software.
On these laptops, TUF and ROG, the LED effects are all done by the keyboard EC. For the TUF series you can reference this
https://gitlab.com/asus-linux/reverse-engineering/-/blob/master/TUF-i2c_laptops/led-rgb
It's for this reason I first went with a single node using "n n n n n n" input.
Kind regards,
Luke.
Luke D. Jones
maintainerPATCH 4/5 asus-wmi: Document many of the undocumented API
In reply to Luke D. Jones--- .../ABI/testing/sysfs-platform-asus-wmi | 50 +++++++++++++++++++ 1 file changed, 50 insertions(+)
Documentation/ABI/testing/sysfs-platform-asus-wmi +50 -0
@@ -57,3 +57,53 @@ Description: * 0 - default, * 1 - overboost, * 2 - silent + +What: /sys/devices/platform/<platform>/dgpu_disable +Date: Dec 2022 +KernelVersion: 5.17 +Contact: "Luke Jones" <[email protected]> +Description: + Disable discrete GPU: + * 0 - Enable dGPU, + * 1 - Disable dGPU, + +What: /sys/devices/platform/<platform>/egpu_enable +Date: Dec 2022 +KernelVersion: 5.17 +Contact: "Luke Jones" <[email protected]> +Description: + Enable the external GPU paired with ROG X-Flow laptops. + Toggling this setting will also trigger ACPI to disable the dGPU: + * 0 - Disable, + * 1 - Enable, + +What: /sys/devices/platform/<platform>/keyboard_rgb_mode +Date: Dec 2022 +KernelVersion: 5.20 +Contact: "Luke Jones" <[email protected]> +Description: + Set some RGB keyboard modes and features (write-only). + + The accepted input is "save mode speed", where "n n n" options + are: + * save - 0 or 1, if 0 then settings are not retained on boot + * mode - 0 to 12, each is an RGB such as static, rainbow, pulse. + Not all keyboards accept every mode. + * speed - 0, 1, 2, equal to low, medium, high. + Only applies to certain modes. + +What: /sys/devices/platform/<platform>/panel_od +Date: Dec 2022 +KernelVersion: 5.20 +Contact: "Luke Jones" <[email protected]> +Description: + Set some RGB keyboard power states (write-only). + + The accepted input is "boot awake sleep keyboard", where "n n n n n" + options are: + * save - 0 or 1, if 0 then settings are not retained on boot + * boot - 0 or 1, controls if a boot animation is shown + * awake - 0 or 1, controls if the keyboard LED are on during awake + * sleep - 0 or 1, controls if a suspended animation is shown. + This is only active if the AC is connected. + * keyboard - 0 or 1, unknown what effect this really has
Signature · 1 line
2.37.1
kernel test robot
build botRe: [PATCH 4/5] asus-wmi: Document many of the undocumented API
Thank you for the patch! Perhaps something to improve:
Hi "Luke,
Thank you for the patch! Perhaps something to improve:
[auto build test WARNING on v5.19]
[cannot apply to linus/master next-20220805]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Luke-D-Jones/asus-wmi-Add-support-for-RGB-keyboards/20220805-162136 base: 3d7cb6b04c3f3115719235cc6866b10326de34cd reproduce: make htmldocs
If you fix the issue, kindly add following tag where applicable
All warnings (new ones prefixed by >>):
>> Documentation/ABI/testing/sysfs-platform-asus-wmi:71: WARNING: Unexpected indentation.
vim +71 Documentation/ABI/testing/sysfs-platform-asus-wmi
> 71 Date: Dec 2022
72 KernelVersion: 5.17
73 Contact: "Luke Jones" <[email protected]>
74 Description:
75 Enable the external GPU paired with ROG X-Flow laptops.
76 Toggling this setting will also trigger ACPI to disable the dGPU:
77 * 0 - Disable,
78 * 1 - Enable,
79 Signature · 2 lines
0-DAY CI Kernel Test Service https://01.org/lkp
Re: [PATCH 4/5] asus-wmi: Document many of the undocumented API
In reply to Luke D. JonesQuoted 1 line · Luke D. Jones
Missed commit message.
Quoted 1 line
Signed-off-by Luke D. Jones <[email protected]>
...
Quoted 1 line
+Date: Dec 2022
I would be more optimistic here...
Quoted 1 line
+KernelVersion: 5.17
...and definitely this is the wrong version. I would suggest 6.0.
Both comments are applicable for other similar cases.
In case you are documenting new and old APIs, split this to two patches with different dates and kernel versions. And commit messages should be different.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Luke D. Jones
maintainerPATCH 5/5 asus-wmi: Convert all attr _show to use sysfs_emit
In reply to Luke D. Jones--- drivers/platform/x86/asus-wmi.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
drivers/platform/x86/asus-wmi.c +7 -7
@@ -914,7 +914,7 @@ static ssize_t charge_control_end_threshold_show(struct device *device,struct device_attribute *attr, char *buf) { - return sprintf(buf, "%d\n", charge_end_threshold); + return sysfs_emit(buf, "%d\n", charge_end_threshold); }static DEVICE_ATTR_RW (charge_control_end_threshold);
@@ -2021,7 +2021,7 @@ static ssize_t pwm1_show(struct device *dev, value =-1 ; } -return sprintf (buf,"%d\n" , value); +return sysfs_emit (buf,"%d\n" , value); } static ssize_t pwm1_store(struct device *dev,
@@ -2081,7 +2081,7 @@ static ssize_t fan1_input_show(struct device *dev,return -ENXIO ; } -return sprintf (buf,"%d\n" , value <0 ?-1 : value*100 ); +return sysfs_emit (buf,"%d\n" , value <0 ?-1 : value*100 ); } static ssize_t pwm1_enable_show(struct device *dev,
@@ -2099,7 +2099,7 @@ static ssize_t pwm1_enable_show(struct device *dev,* in practice on X532FL at least (the bit is always 0) and there's * also nothing in the DSDT to indicate that this behaviour exists. */ -return sprintf (buf,"%d\n" , asus->fan_pwm_mode); +return sysfs_emit (buf,"%d\n" , asus->fan_pwm_mode); } static ssize_t pwm1_enable_store(struct device *dev,
@@ -2167,7 +2167,7 @@ static ssize_t fan1_label_show(struct device *dev,struct device_attribute *attr, char *buf) { - return sprintf(buf, "%s\n", ASUS_FAN_DESC); + return sysfs_emit(buf, "%s\n", ASUS_FAN_DESC); } static ssize_t asus_hwmon_temp1(struct device *dev,
@@ -2360,7 +2360,7 @@ static ssize_t fan_boost_mode_show(struct device *dev, {struct asus_wmi *asus =dev_get_drvdata (dev); -return scnprintf (buf,PAGE_SIZE ,"%d\n" , asus->fan_boost_mode); +return sysfs_emit (buf,"%d\n" , asus->fan_boost_mode); } static ssize_t fan_boost_mode_store(struct device *dev,
@@ -2913,7 +2913,7 @@ static ssize_t throttle_thermal_policy_show(struct device *dev,struct asus_wmi *asus =dev_get_drvdata (dev);u8 mode = asus->throttle_thermal_policy_mode; -return scnprintf (buf,PAGE_SIZE ,"%d\n" , mode); +return sysfs_emit (buf,"%d\n" , mode); } static ssize_t throttle_thermal_policy_store(struct device *dev,
Signature · 1 line
2.37.1
Re: [PATCH 5/5] asus-wmi: Convert all attr _show to use sysfs_emit
On Fri, Aug 5, 2022 at 10:21 AM Luke D. Jones <[email protected]> wrote:
Commit message is missing. It's no go.
I recommend reading [1] to make your contribution to the projects (even close source, if any) better.
Quoted 1 line
Signed-off-by Luke D. Jones <[email protected]>
[1]: https://cbea.ms/git-commit/
Signature · 2 lines
With Best Regards, Andy Shevchenko
Hi!
Quoted 5 lines
This is a patch series to add RGB support for ASUS laptops. The laptops with this RGB tend to be the TUF series of gamer laptops.
The first step is initial bringup of support using the multicolor LED API.
Quoted 7 lines
These types of keyboards implement a slightly more complex interface than just RGB control however - they also have modes with can be static LED, blinking, rainbow, color cycles, and more. They also have some custom animations that can play depending on device state, such as suspended playing a fancy colour cycle, or playing a "wave" animation.
Two of the patches add support for these features.
Please Cc: LED maintainers with LED patches.
Best regards,
Pavel
Signature · 1 line
People of Russia, stop Putin before his war on Ukraine escalates.
Luke Jones
maintainerI'll be sure to do that when I next adjust things. Thanks!
Quoted 28 lines · Pavel Machek
Hi!
Quoted 17 lines
This is a patch series to add RGB support for ASUS laptops. The laptops with this RGB tend to be the TUF series of gamer
laptops.The first step is initial bringup of support using the multicolor
LED API.These types of keyboards implement a slightly more complex
interface than
just RGB control however - they also have modes with can be static
LED,
blinking, rainbow, color cycles, and more. They also have some
custom
animations that can play depending on device state, such as
suspended
playing a fancy colour cycle, or playing a "wave" animation.Quoted 1 line
Two of the patches add support for these features.
Please Cc: LED maintainers with LED patches.
Best regards,
Pavel--
People of Russia, stop Putin before his war on Ukraine escalates.
Quoted 28 lines · Luke D. Jones
This is a patch series to add RGB support for ASUS laptops. The laptops with this RGB tend to be the TUF series of gamer laptops.
The first step is initial bringup of support using the multicolor LED API.
These types of keyboards implement a slightly more complex interface than just RGB control however - they also have modes with can be static LED, blinking, rainbow, color cycles, and more. They also have some custom animations that can play depending on device state, such as suspended playing a fancy colour cycle, or playing a "wave" animation.
Two of the patches add support for these features.
The last patch adds documentation in:
Documentation/ABI/testing/sysfs-platform-asus-wmiSome notes:
- this patch series obsoletes the previous RGB patches by myself
- it is not possible to add attribute groups to multicolor LED as they get overwritten by
led_multicolor_groupsinled_classdev_multicolor_register_ext.- the methods for RGB control do not provide a way to fetch exisiting state, so these methods are WO.
Quoted 8 lines
- There is an existing
asus::kbd_backlight, this provides a 4-step brightness to the RGB (off,low,med,high) individually to multicolor. I was unsure of the effect of adding a similar path so have used theasus::multicolour::kbd_backlightname to be clear about purpose. If theasus::kbd_backlightis off, then no RGB is shown at all.\I'm hopeful that this patch series addresses all previous feedback related to the obsoleted patches.
There are so many patches and versioning of all of this is completely broken. You really have to clean up the mess and realize what version of this is. To me it looks like this series is v5 or so of the previously sent patch(es). Also you missed the changelog between versions so we can see what you have done from vX to vX+1 for the whole range (1 ... X+1).
Signature · 2 lines
With Best Regards, Andy Shevchenko
Luke Jones
maintainerHi,
Quoted 44 lines · Andy Shevchenko
Quoted 43 lines · Luke D. Jones
This is a patch series to add RGB support for ASUS laptops. The laptops with this RGB tend to be the TUF series of gamer
laptops.The first step is initial bringup of support using the multicolor
LED API.These types of keyboards implement a slightly more complex
interface than
just RGB control however - they also have modes with can be static
LED,
blinking, rainbow, color cycles, and more. They also have some
custom
animations that can play depending on device state, such as
suspended
playing a fancy colour cycle, or playing a "wave" animation.Two of the patches add support for these features.
The last patch adds documentation in:
Documentation/ABI/testing/sysfs-platform-asus-wmiSome notes:
- this patch series obsoletes the previous RGB patches by myself
- it is not possible to add attribute groups to multicolor LED as they get overwritten by
led_multicolor_groupsinled_classdev_multicolor_register_ext.- the methods for RGB control do not provide a way to fetch
exisiting
state, so these methods are WO.- There is an existing
asus::kbd_backlight, this provides a 4-step brightness to the RGB (off,low,med,high) individually to
multicolor.
I was unsure of the effect of adding a similar path so have used
the
asus::multicolour::kbd_backlightname to be clear about purpose. If theasus::kbd_backlightis off, then no RGB is shown at all.\
Quoted 5 lines
Quoted 3 lines
I'm hopeful that this patch series addresses all previous feedback
related
to the obsoleted patches.There are so many patches
This is what Hans requested that I do after the previous submissions,
Quoted 2 lines
and versioning of all of this is completely
broken.
I was unsure how to handle this as the previous patches were individual, I thought perhaps this patch series is a good place to restart since the work done is a bit different.
I will try to better track what I do in future.
Quoted 5 lines
You really have to clean up the mess and realize what version of this is. To me it looks like this series is v5 or so of the previously sent patch(es). Also you missed the changelog between versions so we can see what you have done from vX to vX+1 for the whole range (1 ... X+1).
As described before I thought this would hopefully be a good point at which to reset due to the changes requested by Hans which meant that the underlying structure is different.
I do have another version already prepped, so I will do my best to address the previous submissions and your concerns in the cover letter along with a changelog.
Quoted 4 lines
--
With Best Regards,
Andy Shevchenko
Quoted 7 lines · Luke Jones
Quoted 3 lines · Andy Shevchenko
On Fri, Aug 5, 2022 at 10:20 AM Luke D. Jones <[email protected]> wrote:
There are so many patches
This is what Hans requested that I do after the previous submissions,
No, what I'm referring to is that it was so many versions of the same patch(es) that are floating around and it's too messy to understand which version is which and what to consider.
Quoted 8 lines
Quoted 2 lines
and versioning of all of this is completely
broken.I was unsure how to handle this as the previous patches were individual, I thought perhaps this patch series is a good place to restart since the work done is a bit different.
I will try to better track what I do in future.
Thanks!
Quoted 6 lines
Quoted 5 lines
You really have to clean up the mess and realize what version of this is. To me it looks like this series is v5 or so of the previously sent patch(es). Also you missed the changelog between versions so we can see what you have done from vX to vX+1 for the whole range (1 ... X+1).
Quoted 7 lines
As described before I thought this would hopefully be a good point at which to reset due to the changes requested by Hans which meant that the underlying structure is different.
I do have another version already prepped, so I will do my best to address the previous submissions and your concerns in the cover letter along with a changelog.
Thanks. For the less confusion continue this versioning than (v2 will be the next one for the series).
Signature · 2 lines
With Best Regards, Andy Shevchenko
Quoted 2 lines · Luke Jones
On Sat, Aug 6 2022 at 11:10:37 +0200, Andy Shevchenko <[email protected]> wrote:
...
Quoted 1 line
I do have another version already prepped
Hold on and try to address many more review comments. It seems the series needs much more work, otherwise it will be spam in the mailing list and demotivating reviewers to continue.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Luke Jones
maintainerI do agree. It's what I meant by prepped. I think I've addressed everything you've raised, so I'll leave it to bake a few days with my testing then submit new version on Tuesday (Hans please wait for v2).
Many thanks for your time taken to review this. I'm not an expert at C or the kernel by any stretch so reviews are critical for me. Also thank you for the link on git messages - I'll go through each patch and ensure they're better.
Kind regards,
Luke.
Quoted 15 lines · Andy Shevchenko
Quoted 2 lines · Luke Jones
On Sat, Aug 6 2022 at 11:10:37 +0200, Andy Shevchenko <[email protected]> wrote:
...
Quoted 1 line
I do have another version already prepped
Hold on and try to address many more review comments. It seems the series needs much more work, otherwise it will be spam in the mailing list and demotivating reviewers to continue.
--
With Best Regards,
Andy Shevchenko
On Sat, Aug 6, 2022 at 12:49 PM Luke Jones <[email protected]> wrote:
Please, do not top-post! It's not appreciated in the OSS community(ies).
Quoted 3 lines
I do agree. It's what I meant by prepped. I think I've addressed everything you've raised, so I'll leave it to bake a few days with my testing then submit new version on Tuesday (Hans please wait for v2).
We are now at the merge window, it means you have enough time to take review comments and address them carefully, no need to rush. Your series at the best can be in v6.0, which is 2 months ahead, which means we have somewhat 6-7 weeks for you to clean up and make the series better.
Quoted 4 lines
Many thanks for your time taken to review this. I'm not an expert at C or the kernel by any stretch so reviews are critical for me. Also thank you for the link on git messages - I'll go through each patch and ensure they're better.
You are welcome!
Quoted 5 lines
Quoted 3 lines · Andy Shevchenko
Quoted 2 lines · Luke Jones
On Sat, Aug 6 2022 at 11:10:37 +0200, Andy Shevchenko <[email protected]> wrote:
...
Quoted 5 lines
Quoted 5 lines
Quoted 1 line
I do have another version already prepped
Hold on and try to address many more review comments. It seems the series needs much more work, otherwise it will be spam in the mailing list and demotivating reviewers to continue.
Signature · 2 lines
With Best Regards, Andy Shevchenko