Skip to contentSkip to conversation

arm64: dts: ti: add k3-j721e-beagleboneai64

PATCH NAK Robert Nelson 2 participants 2 messages Aug 15, 2022 – Aug 16, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: ti: add k3-j721e-beagleboneai64

BeagleBoard.org BeagleBone AI-64 is an open source hardware single board computer based on the Texas Instruments TDA4VM SoC featuring dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x floating-point VLIW DSPs, 3x dual Arm Cortex-R5 co-processors, 2x 6-core Programmable Real-Time Unit and Industrial Communication SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB DDR4, USB3.0 Type-C, USB HS Type-A, miniDisplayPort, 2x 4-lane CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and BeagleBone expansion headers.

This board family can be indentified by the BBONEAI-64-B0 in the at24 eeprom:

[aa 55 33 ee 01 37 00 10  2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d  00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]

https://beagleboard.org/ai-64
https://git.beagleboard.org/beagleboard/beaglebone-ai-64

CC Nishanth Menon <[email protected]>
CC Vignesh Raghavendra <[email protected]>
CC Tero Kristo <[email protected]>
CC Jason Kridner <[email protected]>
CC Drew Fustini <[email protected]>
---
 arch/arm64/boot/dts/ti/Makefile               |    1 +
 .../boot/dts/ti/k3-j721e-beagleboneai64.dts   | 1143 +++++++++++++++++
 2 files changed, 1144 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts
arch/arm64/boot/dts/ti/Makefile +1 -0
index 02e5d80344d0..4c88e87b42a6 100644
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
 
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +1143 -0

1,143 lines not on this page · raw message

Signature · 7 lines
2.30.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer NAK
#1 lore raw

On 16:37-20220815, Robert Nelson wrote:
[...]

Quoted 18 lines
arch/arm64/boot/dts/ti/Makefile +1 -0
index 02e5d80344d0..4c88e87b42a6 100644
@@ -12,6 +12,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
 
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +0 -0
new file mode 100644
index 000000000000..4748fe492357

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 2

Quoted 2 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +2 -0
@@ -0,0 +1,1143 @@
+// SPDX-License-Identifier: GPL-2.0
+/*

Please add a link here: https://beagleboard.org/ai-64

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2022 Jason Kridner, BeagleBoard.org Foundation
+ * Copyright (C) 2022 Robert Nelson, BeagleBoard.org Foundation
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 22

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	compatible = "beagle,j721e-beagleboneai64", "ti,j721e";
+	model = "BeagleBoard.org BeagleBone AI-64";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	};

we should do aliases - the aliases in k3-j721e.dtsi must move out into the board files.

Quoted 30 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +30 -0
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 4G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};

[...]

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 164

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sw_pwr_pins_default>;
+
+		sw_boot: sw1 {
+			status = "disabled";

Please document why disabled?

Quoted 8 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +8 -0
+			label = "BOOT";
+			linux,code = <BTN_0>;
+			gpios = <&wkup_gpio0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		sw_pwr: sw2 {
+			label = "POWER";
+			linux,code = <KEY_POWER>;

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 182

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+			gpios = <&wkup_gpio0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_leds: gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_default>;
+
+		usr_led0: usr_led0 {

what is wrong with led-0,1,2,3,4 ?

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts: /gpio-leds/usr_led0: Character '_' not recommended in node name

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 183

Quoted 1 line
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +1 -0
+			label = "beaglebone:green:usr0";

please see Documentation/devicetree/bindings/leds/common.yaml label has been deprecated, instead use function and color.

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 185

Quoted 2 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +2 -0
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";

is'nt function a better option?

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 192

Quoted 7 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +7 -0
+			gpios = <&main_gpio0 96 GPIO_ACTIVE_HIGH>;
+		};
+
+		usr_led1: usr_led1 {
+			label = "beaglebone:green:usr1";
+			default-state = "keep";
+			linux,default-trigger = "mmc0";

here and others, please check against Documentation/devicetree/bindings/leds/common.yaml enum list ?

Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +5 -0
+			gpios = <&main_gpio0 95 GPIO_ACTIVE_HIGH>;
+		};
+
+		usr_led2: usr_led2 {
+			label = "beaglebone:green:usr2";

[...]

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 284

Quoted 11 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +11 -0
+	dp_pwr_3v3: fixedregulator-dp-prw {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp0_3v3_en_pins_default>;
+		regulator-name = "dp-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&main_gpio0 49 GPIO_ACTIVE_HIGH>; /* DP0_PWR_SW_EN */
+		enable-active-high;
+
+		/* Always on for now, until dp-connector driver can handle this */

Hmm... I did notice no implementation in drivers for dp-pwr-supply

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 224

Quoted 3 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +3 -0
+		regulator-always-on;
+	};
+
	[...]

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 425

Quoted 9 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +9 -0
+
+&wkup_pmx0 {
+	eeprom_wp_pins_default: eeprom-wp-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xc4, PIN_OUTPUT_PULLUP, 7) /* (G24) WKUP_GPIO0_5 */
+		>;
+	};
+
+	mcu_adc0_pins_default: mcu_adc0_pins_default {

NAK.
dtbs_check should have told you:

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts: /bus@100000/bus@28380000/pinctrl@4301c000/mcu_adc0_pins_default: Character '_' not recommended in node name

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 437

Quoted 12 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +12 -0
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x130, PIN_INPUT, 0) /* (K25) MCU_ADC0_AIN0 */
+			J721E_WKUP_IOPAD(0x134, PIN_INPUT, 0) /* (K26) MCU_ADC0_AIN1 */
+			J721E_WKUP_IOPAD(0x138, PIN_INPUT, 0) /* (K28) MCU_ADC0_AIN2 */
+			J721E_WKUP_IOPAD(0x13c, PIN_INPUT, 0) /* (L28) MCU_ADC0_AIN3 */
+			J721E_WKUP_IOPAD(0x140, PIN_INPUT, 0) /* (K24) MCU_ADC0_AIN4 */
+			J721E_WKUP_IOPAD(0x144, PIN_INPUT, 0) /* (K27) MCU_ADC0_AIN5 */
+			J721E_WKUP_IOPAD(0x148, PIN_INPUT, 0) /* (K29) MCU_ADC0_AIN6 */
+		>;
+	};
+
+	mcu_adc1_pins_default: mcu_adc1_pins_default {

Same '_' issue

Quoted 11 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +11 -0
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x150, PIN_INPUT, 0) /* (N23) MCU_ADC1_AIN0 */
+		>;
+	};
+
+	mikro_bus_pins_default: mikro-bus-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x108, PIN_INPUT, 7) /* SDAPULLEN (E26) PMIC_POWER_EN0.WKUP_GPIO0_66 */
+			J721E_WKUP_IOPAD(0xd4, PIN_INPUT, 7) /* SDA (G26) WKUP_GPIO0_9.MCU_I2C1_SDA */
+			J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 7) /* SDA (D25) MCU_I3C0_SDA.WKUP_GPIO0_61 */
+

[...]

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 511

Quoted 2 lines

+&wkup_uart0 {

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +1 -0
+	/* Wakeup UART is used by System firmware */

More accurate terminology will be TIFS firmware.

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 521

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+	status = "reserved";
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+	/* Shared with ATF on this platform */
+	power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+};
+
	[...]

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 630

Quoted 3 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +3 -0
+
+&main_gpio0 {
+	status = "okay";

I don't think we need a status = "okay" - that has been the default.

Quoted 20 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +20 -0
+	gpio-line-names = "", "P9_11", "P9_13", "P8_17", "P8_18", /* 0-4 */
+		"P8_22", "P8_24", "P8_34", "P8_36", "P8_38A", /* 5-9 */
+		"P9_23", "P8_37B", "P9_26B", "P9_24B", "P8_08", /* 10-14 */
+		"P8_07", "P8_10", "P8_09", "P9_42B", "", /* 15-19 */
+		"P8_03", "TYPEC_PWR_ST", "M2_RSTz", "M2_I2C_ALERT#", "P8_35A", /* 20-24 */
+		"P8_33A", "P8_32A", "", "P9_17A", "", /* 25-29 */
+		"P8_21", "P8_23", "P8_31A", "P8_05", "P8_06", /* 30-34 */
+		"P8_25", "M2_W_DISABLE1#", "M2_W_DISABLE2#", "P9_22A (BOOTMODE1)", "P9_21A", /* 35-39 */
+		"P9_18A", "DSI_I2C_SCL", "DSI_I2C_SDA", "P9_28B", "P9_30B", /* 40-44 */
+		"P9_12", "P9_27A", "P9_15", "P8_04 (BOOTMODE2)", "VCC_DP_EN", /* 45-49 */
+		"P9_33B", "P8_26", "P9_31B", "P9_29B", "P9_39B", /* 50-54 */
+		"P9_35B", "P9_36B", "P9_37B", "P9_38B", "P8_12", /* 55-59 */
+		"P8_11 (BOOTMODE7)", "P8_15", "P8_16", "", "", /* 60-64 */
+		"P8_43", "P8_44", "P8_41", "P8_42 (BOOTMODE6)", "P8_39", /* 65-69 */
+		"P8_40", "P8_27", "P8_28", "P8_29", "P8_30", /* 70-74 */
+		"P8_14", "P8_20", "P9_20B", "P9_19B", "P8_45", /* 75-79 */
+		"P8_46 (BOOTMODE3)", "P9_40B", "VDD_SD_EN", "CSI_I2C_SCL", "CSI_I2C_SDA", /* 80-84 */
+		"M2_I2S_SCK", "M2_I2S_WS", "M2_I2S_IN", "P8_19", "P8_13", /* 85-89 */
+		"P9_21B", "P9_22B", "M2_I2S_OUT", "P9_14", "P9_16", /* 90-94 */
+		"USR1", "USR0", "USR2", "DSI_GPIO1", "FAN_PWM", /* 95-99 */

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 660

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+		"FAN_TACH", "CSI1_GPIO1", "CSI0_GPIO2", "CSI0_GPIO1", "P9_25B", /* 100-104 */
+		"P8_38B", "P8_37A", "CSI1_GPIO2", "DSI_GPIO2", "USR4", /* 105-109 */
+		"USR3", "P8_33B", "DP_HPD", "M2_UART_CTSn", "M2_UART_RTSn", /* 110-114 */
+		"P9_17B", "P8_35B", "VDD_SD_SEL", "P9_26A", "P9_24A", /* 115-119 */
+		"P9_18B", "CONSOLE_RX", "CONSOLE_TX", "P9_42A", "P9_27B", /* 120-124 */
+		"M2_UART_RX", "M2_UART_TX", "P9_25A"; /* 125-127 */
+};
+
+&main_gpio1 {
+	status = "okay";

I don't think we need a status = "okay" - that has been the default.

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 672

Quoted 12 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +12 -0
+	gpio-line-names = "P9_41", "P9_19A", "P9_20A", "TYPEC_DIR", "TYPEC_INT", /* 0-4 */
+		"M2_PCIE_WAKE#", "M2_PCIE_CLKREQ#", "M2_I2C_SCL", "M2_I2C_SDA", "TYPEC/CSI1_I2C_SCL", /* 5-9 */
+		"TYPEC/CSI1_I2C_SDA", "P9_28A", "P9_31A", "P9_30A", "P9_29A", /* 10-14 */
+		"uSD_DAT3", "uSD_DAT2", "uSD_DAT1", "uSD_DAT0", "uSD_CLK", /* 15-19 */
+		"uSD_CMD", "uSD_SDCD", "", "M2_SDIO_DAT3", "M2_SDIO_DAT2", /* 20-24 */
+		"M2_SDIO_DAT1", "M2_SDIO_DAT0", "M2_SDIO_CLK", "M2_SDIO_CMD", "USB1_DRVVBUS", /* 25-29 */
+		"", "", "", "", "", /* 30-34 */
+		"", ""; /* 35-36 */
+};
+
+&main_gpio2 {
+	status = "disabled";

Here and elsewhere, when disabled, please document why.

Quoted 33 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +33 -0
+};
+
+&main_gpio3 {
+	status = "disabled";
+};
+
+&main_gpio4 {
+	status = "disabled";
+};
+
+&main_gpio5 {
+	status = "disabled";
+};
+
+&main_gpio6 {
+	status = "disabled";
+};
+
+&main_gpio7 {
+	status = "disabled";
+};
+
+&wkup_gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_adc0_pins_default &mcu_adc1_pins_default &mikro_bus_pins_default>;
+	gpio-line-names = "MB_CLK/BOOT_BTN", "MB_MISO", "MB_MOSI", "MB_CS", "SOC_WAKE", /* 0-4 */
+		"EEPROM_WP", "SOC_INT2z", "H_MCU_INT#", "MB_SCLA", "MB_SDAA", /* 5-9 */
+		"MCU_RGMII_RST#", "MB_PWM", "MCU_BOOTMODE8", "MCU_BOOTMODE9", "MCU_BOOTMODE6", /* 10-14 */
+		"MCU_BOOTMODE7", "", "", "", "", /* 15-19 */
+		"", "", "", "", "", /* 20-24 */
+		"", "", "", "", "", /* 24-29 */
+		"USB_HUB_RST", "", "", "MB_RX", "MB_TX", /* 30-34 */
+		"MB_INT", "", "MB_RST", "MII_TX_CTL", "MII_RX_CTL", /* 35-39 */

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 715

Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +10 -0
+		"MII_TD3", "MII_TD2", "MII_TD1", "MII_TD0", "MII_TXC", /* 40-44 */
+		"MII_RXC", "MII_RD3", "MII_RD2", "MII_RD1", "MII_RD0", /* 45-49 */
+		"MDIO", "MDC", "MCU_BOOTMODE0", "MCU_BOOTMODE1", "MCU_BOOTMODE2", /* 50-54 */
+		"SYS_MCU_PWRDN", "WKUP_UART_RX", "WKUP_UART_TX", "MII_RST#", "MB_AN", /* 55-59 */
+		"MB_SCLB", "MB_SDAB", "WKUP_I2C0_SCL", "WKUP_I2C0_SDA", "MCU_I2C0_SCL", /* 60-64 */
+		"MCU_I2C0_SDA", "MB_SDAPULLEN", "PMIC_POWER_EN1"; /* 65-67 */
+};
+
+&wkup_gpio1 {
+	status = "disabled";

Please document why disabled.

arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts line 718

Quoted 3 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +3 -0
+};
+
+&main_r5fss0_core0{

space before { please.

Quoted 16 lines
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts new file +16 -0
+	firmware-name = "pdk-ipc/ipc_echo_test_mcu2_0_release_strip.xer5f";
+};
+
+&usb_serdes_mux {
+	idle-states = <1>, <1>; /* USB0 to SERDES3, USB1 to SERDES2 */
+};
+
+&serdes_ln_ctrl {
+	idle-states = <J721E_SERDES0_LANE0_IP4_UNUSED>, <J721E_SERDES0_LANE1_IP4_UNUSED>,
+		      <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
+		      <J721E_SERDES2_LANE0_IP1_UNUSED>, <J721E_SERDES2_LANE1_USB3_1>,
+		      <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
+		      <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
+		      <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+};
+

[...]

Signature · 8 lines
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel