media: mt9p031: Increase post-reset delay
PATCH 1/1 media: mt9p031: Increase post-reset delay
The MT9P006 sensor driver sporadically fails to probe because the sensor responds with a NACK condition to I2C address on the bus during an attempt to read the sensor MT9P031_CHIP_VERSION register in mt9p031_registered().
Neither the MT9P006 nor MT9P031 datasheets are clear on reset signal timing. Older MT9M034 [1] datasheet provides those timing figures in Appendix-A and indicates it is necessary to wait 850000 EXTCLK cycles before starting any I2C communication.
Add such a delay, which does make the sporadic I2C NACK go away, so it is likely similar constraint applies to this sensor.
[1] https://www.onsemi.com/pdf/datasheet/mt9m034-d.pdf
---
Cc: Laurent Pinchart <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Sakari Ailus <[email protected]>
Cc: Stefan Riedmueller <[email protected]>
--- drivers/media/i2c/mt9p031.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/media/i2c/mt9p031.c +4 -1
@@ -307,6 +307,7 @@ static inline int mt9p031_pll_disable(struct mt9p031 *mt9p031)static int mt9p031_power_on (struct mt9p031 *mt9p031) { +unsigned long delay;int ret;/* Ensure RESET_BAR is active */
@@ -334,7 +335,9 @@ static int mt9p031_power_on(struct mt9p031 *mt9p031)/* Now RESET_BAR must be high */ if (mt9p031->reset) {gpiod_set_value (mt9p031->reset,0 ); -usleep_range (1000 ,2000 ); +/* Wait 850000 EXTCLK cycles before de-asserting reset. */ + delay =DIV_ROUND_UP (850000 *1000 ,clk_get_rate (mt9p031->clk)); +msleep (delay); }return 0 ;
Signature · 1 line
2.35.1
Sakari Ailus
maintainerHi Marek,
Quoted 37 lines · Marek Vasut
The MT9P006 sensor driver sporadically fails to probe because the sensor responds with a NACK condition to I2C address on the bus during an attempt to read the sensor
MT9P031_CHIP_VERSIONregister inmt9p031_registered().Neither the MT9P006 nor MT9P031 datasheets are clear on reset signal timing. Older MT9M034 [1] datasheet provides those timing figures in Appendix-A and indicates it is necessary to wait 850000 EXTCLK cycles before starting any I2C communication.
Add such a delay, which does make the sporadic I2C NACK go away, so it is likely similar constraint applies to this sensor.
[1] https://www.onsemi.com/pdf/datasheet/mt9m034-d.pdf
Signed-off-by Marek Vasut <[email protected]>---
Cc: Laurent Pinchart <[email protected]>
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Sakari Ailus <[email protected]>
Cc: Stefan Riedmueller <[email protected]>--- drivers/media/i2c/mt9p031.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)drivers/media/i2c/mt9p031.c +1
-0@@ -307,6 +307,7 @@ static inline int mt9p031_pll_disable(struct mt9p031 *mt9p031)static int mt9p031_power_on (struct mt9p031 *mt9p031) { +unsigned long delay;int ret;/* Ensure RESET_BAR is active */
drivers/media/i2c/mt9p031.c static int mt9p031_power_on(struct mt9p031 *mt9p031) · line 339
Quoted 6 lines
drivers/media/i2c/mt9p031.c +2
-1@@ -334,7 +335,9 @@ static int mt9p031_power_on(struct mt9p031 *mt9p031)/* Now RESET_BAR must be high */ if (mt9p031->reset) {gpiod_set_value (mt9p031->reset,0 ); -usleep_range (1000 ,2000 ); +/* Wait 850000 EXTCLK cycles before de-asserting reset. */ + delay =DIV_ROUND_UP (850000 *1000 ,clk_get_rate (mt9p031->clk));
clk_get_rate() will return 0 if there's no clock. I guess that doesn't happen commonly but it'd be nice to guard against that.
Quoted 4 lines
drivers/media/i2c/mt9p031.c +1
-0+msleep (delay); }return 0 ;
Signature · 3 lines
Regards, Sakari Ailus