arm: dts: imx: sync device trees with upstream linux kernel part 1
Subsystems (8)
cover arm: dts: imx: sync device trees with upstream linux kernel part 1
From: Marcel Ziswiler <[email protected]>
This series synchronises them imx device trees with the upstream Linux kernel (v6.0-rc1). I split it into two parts. This is part 1.
It also fixes a few issues as discussed during/after the pre-mature application of my first series [1].
I am not touching kontron-sl-mx6ul as Frieder already took care of those [2].
Feedback welcome. Thanks!
[1] https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
[2] https://patchwork.ozlabs.org/project/uboot/cover/[email protected]/
Marcel Ziswiler (8):
vf610: synchronise device tree with linux
imxrt1020: fix lpuart issue in common u-boot device tree
imxrt1050: synchronise device tree with linux
imx8ulp: synchronise device tree with linux
imx8mq: synchronise device tree with linux
imx8mp: synchronise device tree with linux
imx8mn: synchronise device tree with linux
imx8mm: synchronise device tree with linux
arch/arm/dts/imx8mm-beacon-baseboard.dtsi | 4 +- arch/arm/dts/imx8mm-evk.dtsi | 43 ++ arch/arm/dts/imx8mm-icore-mx8mm.dtsi | 12 +- arch/arm/dts/imx8mm-mx8menlo.dts | 4 +- arch/arm/dts/imx8mm-u-boot.dtsi | 2 +- arch/arm/dts/imx8mm-venice-gw700x.dtsi | 24 +- arch/arm/dts/imx8mm-venice-gw7901.dts | 8 +- arch/arm/dts/imx8mm-venice-gw7902.dts | 10 +- arch/arm/dts/imx8mm-venice-gw7903.dts | 6 +- arch/arm/dts/imx8mm-verdin.dtsi | 10 +- arch/arm/dts/imx8mn-beacon-baseboard.dtsi | 4 +- arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi | 2 +- .../dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi | 2 +- arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi | 2 +- arch/arm/dts/imx8mn-evk.dtsi | 45 +- .../dts/imx8mn-var-som-symphony-u-boot.dtsi | 2 +- arch/arm/dts/imx8mn-var-som-symphony.dts | 6 +- arch/arm/dts/imx8mn-venice-gw7902.dts | 8 +- arch/arm/dts/imx8mn-venice-u-boot.dtsi | 2 +- arch/arm/dts/imx8mn.dtsi | 13 +- arch/arm/dts/imx8mp-dhcom-pdk2.dts | 27 +- arch/arm/dts/imx8mp-dhcom-som.dtsi | 20 +- arch/arm/dts/imx8mp-evk.dts | 126 ++-- arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 48 +- arch/arm/dts/imx8mp-u-boot.dtsi | 2 +- arch/arm/dts/imx8mp-venice-gw74xx.dts | 116 ++-- arch/arm/dts/imx8mp-verdin.dtsi | 14 +- arch/arm/dts/imx8mp.dtsi | 33 +- arch/arm/dts/imx8mq-evk.dts | 43 ++ arch/arm/dts/imx8mq-u-boot.dtsi | 10 +- arch/arm/dts/imx8mq.dtsi | 15 +- arch/arm/dts/imx8ulp-evk-u-boot.dtsi | 6 +- arch/arm/dts/imx8ulp-evk.dts | 191 +----- arch/arm/dts/imx8ulp-pinfunc.h | 4 +- arch/arm/dts/imx8ulp.dtsi | 564 +++++------------- arch/arm/dts/imxrt1020-evk-u-boot.dtsi | 7 +- arch/arm/dts/imxrt1020-evk.dts | 1 - arch/arm/dts/imxrt1050-evk-u-boot.dtsi | 25 +- arch/arm/dts/imxrt1050-evk.dts | 257 +------- arch/arm/dts/imxrt1050-pinfunc.h | 2 +- arch/arm/dts/imxrt1050.dtsi | 168 +++--- arch/arm/dts/vf610-pinfunc.h | 2 +- include/dt-bindings/clock/imx8mp-clock.h | 13 +- include/dt-bindings/clock/imx8ulp-clock.h | 49 +- include/dt-bindings/clock/imxrt1050-clock.h | 9 +- include/dt-bindings/interconnect/imx8mm.h | 50 ++ include/dt-bindings/interconnect/imx8mn.h | 41 ++ include/dt-bindings/power/imx8mp-power.h | 15 +- include/dt-bindings/power/imx8ulp-power.h | 26 + include/dt-bindings/reset/imx8mp-reset.h | 50 ++ include/dt-bindings/reset/imx8mq-reset.h | 61 +- include/dt-bindings/reset/imx8ulp-pcc-reset.h | 59 ++ 52 files changed, 1007 insertions(+), 1256 deletions(-) create mode 100644 include/dt-bindings/interconnect/imx8mm.h create mode 100644 include/dt-bindings/interconnect/imx8mn.h create mode 100644 include/dt-bindings/power/imx8ulp-power.h create mode 100644 include/dt-bindings/reset/imx8mp-reset.h create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
Signature · 1 line
2.35.1
PATCH 1/8 vf610: synchronise device tree with linux
From: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1 plus the recent DDR pinmux addition still being in-flight.
---
arch/arm/dts/vf610-pinfunc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/vf610-pinfunc.h +1 -1
@@ -802,7 +802,6 @@#define VF610_PAD_PTE28__EWM_OUT 0x214 0x000 ALT7 0x0#define VF610_PAD_PTA7__GPIO_134 0x218 0x000 ALT0 0x0#define VF610_PAD_PTA7__VIU_PIX_CLK 0x218 0x3AC ALT1 0x1 -#define VF610_PAD_DDR_RESETB 0x21c 0x000 ALT0 0x0#define VF610_PAD_DDR_A15__DDR_A_15 0x220 0x000 ALT0 0x0#define VF610_PAD_DDR_A14__DDR_A_14 0x224 0x000 ALT0 0x0
@@ -853,4 +852,5 @@#define VF610_PAD_DDR_ODT0__DDR_ODT_1 0x2d8 0x000 ALT0 0x0#define VF610_PAD_DDR_DDRBYTE1__DDR_DDRBYTE1 0x2dc 0x000 ALT0 0x0#define VF610_PAD_DDR_DDRBYTE2__DDR_DDRBYTE2 0x2e0 0x000 ALT0 0x0 +#endif
Signature · 1 line
2.35.1
PATCH 2/8 imxrt1020: fix lpuart issue in common u-boot device tree
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Fix lpuart issue in common U-Boot device tree.
---
arch/arm/dts/imxrt1020-evk-u-boot.dtsi | 7 ++++--- arch/arm/dts/imxrt1020-evk.dts | 1 - 2 files changed, 4 insertions(+), 4 deletions(-)
arch/arm/dts/imxrt1020-evk-u-boot.dtsi +4 -3
@@ -67,9 +67,6 @@ imxrt1020-evk { u-boot,dm-spl; - pinctrl_lpuart1: lpuart1grp { - u-boot,dm-spl; - }; pinctrl_semc: semcgrp { u-boot,dm-spl;
@@ -81,6 +78,10 @@ }; }; +&pinctrl_lpuart1 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };
arch/arm/dts/imxrt1020-evk.dts +0 -1
@@ -6,7 +6,6 @@ /dts-v1/; #include "imxrt1020.dtsi" -#include "imxrt1020-evk-u-boot.dtsi" #include "imxrt1020-pinfunc.h" / {
Signature · 1 line
2.35.1
PATCH 3/8 imxrt1050: synchronise device tree with linux
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
---
arch/arm/dts/imxrt1050-evk-u-boot.dtsi | 25 +- arch/arm/dts/imxrt1050-evk.dts | 257 +++----------------- arch/arm/dts/imxrt1050-pinfunc.h | 2 +- arch/arm/dts/imxrt1050.dtsi | 168 ++++++------- include/dt-bindings/clock/imxrt1050-clock.h | 9 +- 5 files changed, 118 insertions(+), 343 deletions(-)
arch/arm/dts/imxrt1050-evk-u-boot.dtsi +9 -16
@@ -50,7 +50,7 @@ u-boot,dm-spl; }; -&gpt1 { +&gpt { u-boot,dm-spl; };
@@ -58,33 +58,26 @@ u-boot,dm-spl; }; -&semc { - u-boot,dm-spl; - - bank1: bank@0 { - u-boot,dm-spl; - }; -}; - &iomuxc { u-boot,dm-spl; imxrt1050-evk { u-boot,dm-spl; - pinctrl_lpuart1: lpuart1grp { - u-boot,dm-spl; - }; pinctrl_semc: semcgrp { u-boot,dm-spl; }; - - pinctrl_usdhc0: usdhc0grp { - u-boot,dm-spl; - }; }; }; +&pinctrl_lpuart1 { + u-boot,dm-spl; +}; + +&pinctrl_usdhc0 { + u-boot,dm-spl; +}; + &usdhc1 { u-boot,dm-spl; };
arch/arm/dts/imxrt1050-evk.dts +31 -226
294 lines not on this page · raw message
arch/arm/dts/imxrt1050-pinfunc.h +1 -1
@@ -1,4 +1,4 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright (C) 2019 * Author(s): Giulio Benetti <[email protected]>
arch/arm/dts/imxrt1050.dtsi +70 -98
248 lines not on this page · raw message
include/dt-bindings/clock/imxrt1050-clock.h +7 -2
@@ -1,4 +1,4 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ /* * Copyright(C) 2019 * Author(s): Giulio Benetti <[email protected]>
@@ -62,6 +62,11 @@#define IMXRT1050_CLK_PLL7_USB_HOST 53#define IMXRT1050_CLK_LCDIF_PIX 54#define IMXRT1050_CLK_USBOH3 55 -#define IMXRT1050_CLK_END 56 +#define IMXRT1050_CLK_IPG_PDOF 56 +#define IMXRT1050_CLK_PER_CLK_SEL 57 +#define IMXRT1050_CLK_PER_PDOF 58 +#define IMXRT1050_CLK_DMA 59 +#define IMXRT1050_CLK_DMA_MUX 60 +#define IMXRT1050_CLK_END 61#endif /* __DT_BINDINGS_CLOCK_IMXRT1050_H */
Signature · 1 line
2.35.1
Fabio Estevam
reviewerRe: [PATCH v1 3/8] imxrt1050: synchronise device tree with linux
Hi Marcel,
Quoted 4 lines · Marcel Ziswiler
From: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
Thanks for working on this.
arch/arm/dts/imxrt1050-evk.dts line 43
Quoted 10 lines
-&semc {
arch/arm/dts/imxrt1050-evk.dts +0
-9- /* - * Memory configuration from sdram datasheet IS42S16160J-6BLI - */ - fsl,sdram-mux = /bits/ 8 <MUX_A8_SDRAM_A8 - MUX_CSX0_SDRAM_CS1 - 0 - 0 - 0 - 0>;
Shouldn't this go to imxrt1050-evk-u-boot.dts?
This node is responsible for describing the DDR timings. Removing it will cause boot regression.
I don't have access to this platform. Adding Jesse and Giulio.
Re: [PATCH v1 3/8] imxrt1050: synchronise device tree with linux
Quoted 21 lines · Fabio Estevam
Hi Marcel,
Quoted 4 lines · Marcel Ziswiler
From: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
Thanks for working on this.
arch/arm/dts/imxrt1050-evk.dts line 43
Quoted 10 lines
-&semc {
arch/arm/dts/imxrt1050-evk.dts +0
-9- /* - * Memory configuration from sdram datasheet IS42S16160J-6BLI - */ - fsl,sdram-mux = /bits/ 8 <MUX_A8_SDRAM_A8 - MUX_CSX0_SDRAM_CS1 - 0 - 0 - 0 - 0>;
Quoted 4 lines
Shouldn't this go to
imxrt1050-evk-u-boot.dts?This node is responsible for describing the DDR timings. Removing it will cause boot regression.
Yes it will. Linux doesn't have LCD or dram yet, it should be moved into imxrt1050-evk-u-boot.dtsi. If needed I can sync it as well as test.
Thanks,
Jesse
Quoted 2 lines
I don't have access to this platform. Adding Jesse and Giulio.
Re: [PATCH v1 3/8] imxrt1050: synchronise device tree with linux
Hi Fabio and Jesse
Quoted 24 lines · Jesse Taube
Quoted 21 lines · Fabio Estevam
Hi Marcel,
Quoted 4 lines · Marcel Ziswiler
From: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
Thanks for working on this.
Quoted 10 lines
-&semc {
- /*
- * Memory configuration from sdram datasheet IS42S16160J-6BLI - */
- fsl,sdram-mux = /bits/ 8 <MUX_A8_SDRAM_A8
-MUX_CSX0_SDRAM_CS1
- 0
- 0
- 0
- 0>;
Quoted 7 lines
Quoted 4 lines
Shouldn't this go to
imxrt1050-evk-u-boot.dts?This node is responsible for describing the DDR timings. Removing it will cause boot regression.
Yes it will. Linux doesn't have LCD or dram yet, it should be moved into
imxrt1050-evk-u-boot.dtsi. If needed I can sync it as well as test.
Sorry, that I did not spot that one. I can update this and send out a v2 with that fixed shortly, don't worry. But if you can then test it that would be great. Thanks!
Quoted 4 lines
Thanks,
JesseQuoted 2 lines
I don't have access to this platform. Adding Jesse and Giulio.
Cheers
Marcel
PATCH 4/8 imx8ulp: synchronise device tree with linux
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
---
arch/arm/dts/imx8ulp-evk-u-boot.dtsi | 6 +- arch/arm/dts/imx8ulp-evk.dts | 191 +----- arch/arm/dts/imx8ulp-pinfunc.h | 4 +- arch/arm/dts/imx8ulp.dtsi | 564 +++++------------- include/dt-bindings/clock/imx8ulp-clock.h | 49 +- include/dt-bindings/power/imx8ulp-power.h | 26 + include/dt-bindings/reset/imx8ulp-pcc-reset.h | 59 ++ 7 files changed, 269 insertions(+), 630 deletions(-) create mode 100644 include/dt-bindings/power/imx8ulp-power.h create mode 100644 include/dt-bindings/reset/imx8ulp-pcc-reset.h
arch/arm/dts/imx8ulp-evk-u-boot.dtsi +1 -5
@@ -3,7 +3,7 @@ * Copyright 2021 NXP */ -&{/soc@0} { +&soc { u-boot,dm-spl; };
@@ -23,10 +23,6 @@ u-boot,dm-spl; }; -&s400_mu { - u-boot,dm-spl; -}; - &lpuart5 { u-boot,dm-spl; };
arch/arm/dts/imx8ulp-evk.dts +16 -175
224 lines not on this page · raw message
arch/arm/dts/imx8ulp-pinfunc.h +2 -2
@@ -1,6 +1,6 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ +/* SPDX-License-Identifier: GPL-2.0+ OR MIT */ /* -* Copyright 2020 NXP +* Copyright 2021 NXP */ #ifndef __DTS_IMX8ULP_PINFUNC_H
arch/arm/dts/imx8ulp.dtsi +135 -429
742 lines not on this page · raw message
include/dt-bindings/clock/imx8ulp-clock.h +30 -19
108 lines not on this page · raw message
include/dt-bindings/power/imx8ulp-power.h new file +26 -0
@@ -0,0 +1,26 @@ +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */ +/* +* Copyright 2021 NXP +*/ + +#ifndef __DT_BINDINGS_IMX8ULP_POWER_H__ +#define __DT_BINDINGS_IMX8ULP_POWER_H__ + +#define IMX8ULP_PD_DMA1 0 +#define IMX8ULP_PD_FLEXSPI2 1 +#define IMX8ULP_PD_USB0 2 +#define IMX8ULP_PD_USDHC0 3 +#define IMX8ULP_PD_USDHC1 4 +#define IMX8ULP_PD_USDHC2_USB1 5 +#define IMX8ULP_PD_DCNANO 6 +#define IMX8ULP_PD_EPDC 7 +#define IMX8ULP_PD_DMA2 8 +#define IMX8ULP_PD_GPU2D 9 +#define IMX8ULP_PD_GPU3D 10 +#define IMX8ULP_PD_HIFI4 11 +#define IMX8ULP_PD_ISI 12 +#define IMX8ULP_PD_MIPI_CSI 13 +#define IMX8ULP_PD_MIPI_DSI 14 +#define IMX8ULP_PD_PXP 15 + +#endif
include/dt-bindings/reset/imx8ulp-pcc-reset.h new file +59 -0
59 lines not on this page · raw message
Signature · 1 line
2.35.1
PATCH 5/8 imx8mq: synchronise device tree with linux
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
---
arch/arm/dts/imx8mq-evk.dts | 43 +++++++++++++++++ arch/arm/dts/imx8mq-u-boot.dtsi | 10 ++-- arch/arm/dts/imx8mq.dtsi | 15 +++--- include/dt-bindings/reset/imx8mq-reset.h | 61 +++++++++++++----------- 4 files changed, 88 insertions(+), 41 deletions(-)
arch/arm/dts/imx8mq-evk.dts +43 -0
@@ -71,12 +71,36 @@ linux,autosuspend-period = <125>; }; + audio_codec_bt_sco: audio-codec-bt-sco { + compatible = "linux,bt-sco"; + #sound-dai-cells = <1>; + }; + wm8524: audio-codec { #sound-dai-cells = <0>; compatible = "wlf,wm8524"; wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; }; + sound-bt-sco { + compatible = "simple-audio-card"; + simple-audio-card,name = "bt-sco-audio"; + simple-audio-card,format = "dsp_a"; + simple-audio-card,bitclock-inversion; + simple-audio-card,frame-master = <&btcpu>; + simple-audio-card,bitclock-master = <&btcpu>; + + btcpu: simple-audio-card,cpu { + sound-dai = <&sai3>; + dai-tdm-slot-num = <2>; + dai-tdm-slot-width = <16>; + }; + + simple-audio-card,codec { + sound-dai = <&audio_codec_bt_sco 1>; + }; + }; + sound-wm8524 { compatible = "simple-audio-card"; simple-audio-card,name = "wm8524-audio";
@@ -386,6 +410,16 @@ status = "okay"; }; +&sai3 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MQ_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + &snvs_pwrkey { status = "okay"; };
@@ -548,6 +582,15 @@ >; }; + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + pinctrl_spdif1: spdif1grp { fsl,pins = < MX8MQ_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6
arch/arm/dts/imx8mq-u-boot.dtsi +5 -5
@@ -10,23 +10,23 @@ }; -&{/soc@0} { +&soc { u-boot,dm-spl; }; -&{/soc@0/bus@30000000} { +&aips1 { u-boot,dm-spl; }; -&{/soc@0/bus@30400000} { +&aips2 { u-boot,dm-spl; }; -&{/soc@0/bus@30800000} { +&aips3 { u-boot,dm-spl; }; -&{/soc@0/bus@32c00000} { +&aips4 { u-boot,dm-spl; };
arch/arm/dts/imx8mq.dtsi +8 -7
@@ -94,7 +94,7 @@ clk_ext4: clock-ext4 { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency= <133000000>; + clock-frequency = <133000000>; clock-output-names = "clk_ext4"; };
@@ -320,7 +320,7 @@ arm,no-tick-in-suspend; }; - soc@0 { + soc: soc@0 { compatible = "fsl,imx8mq-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>;
@@ -329,7 +329,7 @@ nvmem-cells = <&imx8mq_uid>; nvmem-cell-names = "soc_unique_id"; - bus@30000000 { /* AIPS1 */ + aips1: bus@30000000 { /* AIPS1 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x30000000 0x400000>; #address-cells = <1>;
@@ -507,7 +507,7 @@ <0x00030005 0x00000053>, <0x00030006 0x0000005f>, <0x00030007 0x00000071>; - #thermal-sensor-cells = <1>; + #thermal-sensor-cells = <1>; }; wdog1: watchdog@30280000 {
@@ -784,7 +784,7 @@ }; }; - bus@30400000 { /* AIPS2 */ + aips2: bus@30400000 { /* AIPS2 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x30400000 0x400000>; #address-cells = <1>;
@@ -844,7 +844,7 @@ }; }; - bus@30800000 { /* AIPS3 */ + aips3: bus@30800000 { /* AIPS3 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x30800000 0x400000>; #address-cells = <1>;
@@ -1018,6 +1018,7 @@ compatible = "fsl,sec-v4.0-job-ring"; reg = <0x1000 0x1000>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; }; sec_jr1: jr@2000 {
@@ -1369,7 +1370,7 @@ }; }; - bus@32c00000 { /* AIPS4 */ + aips4: bus@32c00000 { /* AIPS4 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x32c00000 0x400000>; #address-cells = <1>;
include/dt-bindings/reset/imx8mq-reset.h +32 -29
69 lines not on this page · raw message
Signature · 1 line
2.35.1
PATCH 6/8 imx8mp: synchronise device tree with linux
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
---
arch/arm/dts/imx8mp-dhcom-pdk2.dts | 27 +++-- arch/arm/dts/imx8mp-dhcom-som.dtsi | 20 +--- arch/arm/dts/imx8mp-evk.dts | 126 +++++++++++--------- arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 48 ++++---- arch/arm/dts/imx8mp-u-boot.dtsi | 2 +- arch/arm/dts/imx8mp-venice-gw74xx.dts | 116 +++++++++--------- arch/arm/dts/imx8mp-verdin.dtsi | 14 ++- arch/arm/dts/imx8mp.dtsi | 33 ++++- include/dt-bindings/clock/imx8mp-clock.h | 13 +- include/dt-bindings/power/imx8mp-power.h | 15 ++- include/dt-bindings/reset/imx8mp-reset.h | 50 ++++++++ 11 files changed, 284 insertions(+), 180 deletions(-) create mode 100644 include/dt-bindings/reset/imx8mp-reset.h
arch/arm/dts/imx8mp-dhcom-pdk2.dts +19 -8
@@ -19,7 +19,6 @@ }; gpio-keys { - #size-cells = <0>; compatible = "gpio-keys"; button-0 {
@@ -62,7 +61,7 @@ led { compatible = "gpio-leds"; - led-5 { + led-0 { color = <LED_COLOR_ID_GREEN>; default-state = "off"; function = LED_FUNCTION_INDICATOR;
@@ -71,7 +70,7 @@ pinctrl-names = "default"; }; - led-6 { + led-1 { color = <LED_COLOR_ID_GREEN>; default-state = "off"; function = LED_FUNCTION_INDICATOR;
@@ -80,7 +79,7 @@ pinctrl-names = "default"; }; - led-7 { + led-2 { color = <LED_COLOR_ID_GREEN>; default-state = "off"; function = LED_FUNCTION_INDICATOR;
@@ -89,7 +88,7 @@ pinctrl-names = "default"; }; - led-8 { + led-3 { color = <LED_COLOR_ID_GREEN>; default-state = "off"; function = LED_FUNCTION_INDICATOR;
@@ -118,10 +117,11 @@ mdio { ethphypdk: ethernet-phy@7 { /* KSZ 9021 */ compatible = "ethernet-phy-ieee802.3-c22"; - interrupt-parent = <&gpio4>; - interrupts = <3 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&pinctrl_ethphy1>; pinctrl-names = "default"; + interrupt-parent = <&gpio4>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + max-speed = <100>; reg = <7>; reset-assert-us = <1000>; reset-deassert-us = <1000>;
@@ -138,7 +138,6 @@ txd2-skew-ps = <0>; txd3-skew-ps = <0>; txen-skew-ps = <0>; - max-speed = <100>; }; }; };
@@ -150,3 +149,15 @@ &usb3_1 { fsl,over-current-active-low; }; + +&iomuxc { + /* + * GPIO_A,B,C,D are connected to buttons. + * GPIO_E,F,H,I are connected to LEDs. + * GPIO_M is connected to CLKOUT2. + */ + pinctrl-0 = <&pinctrl_hog_base + &pinctrl_dhcom_g &pinctrl_dhcom_j + &pinctrl_dhcom_k &pinctrl_dhcom_l + &pinctrl_dhcom_int>; +};
arch/arm/dts/imx8mp-dhcom-som.dtsi +4 -16
@@ -1,4 +1,4 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// SPDX-License-Identifier: GPL-2.0 /* * Copyright (C) 2021-2022 Marek Vasut <[email protected]> */
@@ -224,10 +224,6 @@ }; &i2c3 { - /* - * iMX8MP 1P33A Errata ERR007805 - * I2C is limited to 384 kHz due to SoC bug. - */ clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c3>;
@@ -393,10 +389,6 @@ }; &i2c4 { - /* - * iMX8MP 1P33A Errata ERR007805 - * I2C is limited to 384 kHz due to SoC bug. - */ clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c4>;
@@ -407,10 +399,6 @@ }; &i2c5 { /* HDMI EDID bus */ - /* - * iMX8MP 1P33A Errata ERR007805 - * I2C is limited to 384 kHz due to SoC bug. - */ clock-frequency = <100000>; pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c5>;
@@ -802,8 +790,8 @@ pinctrl_i2c5: dhcom-i2c5-grp { fsl,pins = < - MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x40000084 - MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x40000084 + MX8MP_IOMUXC_HDMI_DDC_SCL__I2C5_SCL 0x40000084 + MX8MP_IOMUXC_HDMI_DDC_SDA__I2C5_SDA 0x40000084 >; };
@@ -830,7 +818,7 @@ pinctrl_rtc: dhcom-rtc-grp { fsl,pins = < /* RTC_#INT Interrupt */ - MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x400001c6 + MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05 0x40000080 >; };
arch/arm/dts/imx8mp-evk.dts +71 -55
212 lines not on this page · raw message
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +24 -24
93 lines not on this page · raw message
arch/arm/dts/imx8mp-u-boot.dtsi +1 -1
@@ -10,7 +10,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mp-venice-gw74xx.dts +58 -58
201 lines not on this page · raw message
arch/arm/dts/imx8mp-verdin.dtsi +11 -3
@@ -49,7 +49,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gpio_keys>; - wakeup { + button-wakeup { debounce-interval = <10>; /* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */ gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
@@ -146,6 +146,14 @@ }; }; +&cpu_alert0 { + temperature = <95000>; +}; + +&cpu_crit0 { + temperature = <105000>; +}; + /* Verdin SPI_1 */ &ecspi1 { #address-cells = <1>;
@@ -619,7 +627,7 @@ interrupts = <5 IRQ_TYPE_EDGE_FALLING>; reg = <0x4a>; /* Verdin GPIO_2 (SODIMM 208) */ - reset-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; status = "disabled"; }; };
@@ -696,7 +704,7 @@ pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>; reg = <0x4a>; /* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */ - reset-gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; status = "disabled"; };
arch/arm/dts/imx8mp.dtsi +27 -6
@@ -195,7 +195,7 @@ clk_ext4: clock-ext4 { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency= <133000000>; + clock-frequency = <133000000>; clock-output-names = "clk_ext4"; };
@@ -293,7 +293,7 @@ arm,no-tick-in-suspend; }; - soc@0 { + soc: soc@0 { compatible = "fsl,imx8mp-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>;
@@ -595,7 +595,7 @@ pgc_ispdwp: power-domain@18 { #power-domain-cells = <0>; reg = <IMX8MP_POWER_DOMAIN_MEDIAMIX_ISPDWP>; - clocks = <&clk IMX8MP_CLK_MEDIA_ISP_DIV>; + clocks = <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>; }; }; };
@@ -791,6 +791,7 @@ compatible = "fsl,sec-v4.0-job-ring"; reg = <0x1000 0x1000>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; }; sec_jr1: jr@2000 {
@@ -903,7 +904,7 @@ <&clk IMX8MP_CLK_USDHC1_ROOT>; clock-names = "ipg", "ahb", "per"; fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; + fsl,tuning-step = <2>; bus-width = <4>; status = "disabled"; };
@@ -917,7 +918,7 @@ <&clk IMX8MP_CLK_USDHC2_ROOT>; clock-names = "ipg", "ahb", "per"; fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; + fsl,tuning-step = <2>; bus-width = <4>; status = "disabled"; };
@@ -931,7 +932,7 @@ <&clk IMX8MP_CLK_USDHC3_ROOT>; clock-names = "ipg", "ahb", "per"; fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; + fsl,tuning-step = <2>; bus-width = <4>; status = "disabled"; };
@@ -1018,6 +1019,26 @@ }; }; + noc: interconnect@32700000 { + compatible = "fsl,imx8mp-noc", "fsl,imx8m-noc"; + reg = <0x32700000 0x100000>; + clocks = <&clk IMX8MP_CLK_NOC>; + #interconnect-cells = <1>; + operating-points-v2 = <&noc_opp_table>; + + noc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-200M { + opp-hz = /bits/ 64 <200000000>; + }; + + opp-1000M { + opp-hz = /bits/ 64 <1000000000>; + }; + }; + }; + aips4: bus@32c00000 { compatible = "fsl,aips-bus", "simple-bus"; reg = <0x32c00000 0x400000>;
include/dt-bindings/clock/imx8mp-clock.h +8 -5
@@ -117,7 +117,6 @@#define IMX8MP_CLK_AUDIO_AHB 108#define IMX8MP_CLK_MIPI_DSI_ESC_RX 109#define IMX8MP_CLK_IPG_ROOT 110 -#define IMX8MP_CLK_IPG_AUDIO_ROOT 111#define IMX8MP_CLK_DRAM_ALT 112#define IMX8MP_CLK_DRAM_APB 113#define IMX8MP_CLK_VPU_G1 114
@@ -125,7 +124,6 @@#define IMX8MP_CLK_CAN1 116#define IMX8MP_CLK_CAN2 117#define IMX8MP_CLK_MEMREPAIR 118 -#define IMX8MP_CLK_PCIE_PHY 119#define IMX8MP_CLK_PCIE_AUX 120#define IMX8MP_CLK_I2C5 121#define IMX8MP_CLK_I2C6 122
@@ -182,8 +180,6 @@#define IMX8MP_CLK_MEDIA_CAM2_PIX 173#define IMX8MP_CLK_MEDIA_LDB 174#define IMX8MP_CLK_MEDIA_MIPI_CSI2_ESC 175 -#define IMX8MP_CLK_PCIE2_CTRL 176 -#define IMX8MP_CLK_PCIE2_PHY 177#define IMX8MP_CLK_MEDIA_MIPI_TEST_BYTE 178#define IMX8MP_CLK_ECSPI3 179#define IMX8MP_CLK_PDM 180
@@ -321,8 +317,15 @@#define IMX8MP_CLK_AUDIO_AXI 310#define IMX8MP_CLK_HSIO_AXI 311#define IMX8MP_CLK_MEDIA_ISP 312 +#define IMX8MP_CLK_MEDIA_DISP2_PIX 313 +#define IMX8MP_CLK_CLKOUT1_SEL 314 +#define IMX8MP_CLK_CLKOUT1_DIV 315 +#define IMX8MP_CLK_CLKOUT1 316 +#define IMX8MP_CLK_CLKOUT2_SEL 317 +#define IMX8MP_CLK_CLKOUT2_DIV 318 +#define IMX8MP_CLK_CLKOUT2 319 -#define IMX8MP_CLK_END 313 +#define IMX8MP_CLK_END 320#define IMX8MP_CLK_AUDIOMIX_SAI1_IPG 0#define IMX8MP_CLK_AUDIOMIX_SAI1_MCLK1 1
include/dt-bindings/power/imx8mp-power.h +11 -4
@@ -38,9 +38,16 @@#define IMX8MP_MEDIABLK_PD_ISI 3#define IMX8MP_MEDIABLK_PD_MIPI_CSI2_2 4#define IMX8MP_MEDIABLK_PD_LCDIF_2 5 -#define IMX8MP_MEDIABLK_PD_ISP2 6 -#define IMX8MP_MEDIABLK_PD_ISP1 7 -#define IMX8MP_MEDIABLK_PD_DWE 8 -#define IMX8MP_MEDIABLK_PD_MIPI_DSI_2 9 +#define IMX8MP_MEDIABLK_PD_ISP 6 +#define IMX8MP_MEDIABLK_PD_DWE 7 +#define IMX8MP_MEDIABLK_PD_MIPI_DSI_2 8 + +#define IMX8MP_HDMIBLK_PD_IRQSTEER 0 +#define IMX8MP_HDMIBLK_PD_LCDIF 1 +#define IMX8MP_HDMIBLK_PD_PAI 2 +#define IMX8MP_HDMIBLK_PD_PVI 3 +#define IMX8MP_HDMIBLK_PD_TRNG 4 +#define IMX8MP_HDMIBLK_PD_HDMI_TX 5 +#define IMX8MP_HDMIBLK_PD_HDMI_TX_PHY 6#endif
include/dt-bindings/reset/imx8mp-reset.h new file +50 -0
50 lines not on this page · raw message
Signature · 1 line
2.35.1
PATCH 7/8 imx8mn: synchronise device tree with linux
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
---
arch/arm/dts/imx8mn-beacon-baseboard.dtsi | 4 +- arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi | 2 +- .../dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi | 2 +- arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi | 2 +- arch/arm/dts/imx8mn-evk.dtsi | 45 ++++++++++++++++++- .../dts/imx8mn-var-som-symphony-u-boot.dtsi | 2 +- arch/arm/dts/imx8mn-var-som-symphony.dts | 6 +-- arch/arm/dts/imx8mn-venice-gw7902.dts | 8 ++-- arch/arm/dts/imx8mn-venice-u-boot.dtsi | 2 +- arch/arm/dts/imx8mn.dtsi | 13 +++--- include/dt-bindings/interconnect/imx8mn.h | 41 +++++++++++++++++ 11 files changed, 106 insertions(+), 21 deletions(-) create mode 100644 include/dt-bindings/interconnect/imx8mn.h
arch/arm/dts/imx8mn-beacon-baseboard.dtsi +2 -2
@@ -146,7 +146,7 @@ }; &easrc { - fsl,asrc-rate = <48000>; + fsl,asrc-rate = <48000>; status = "okay"; };
@@ -182,7 +182,7 @@ &usbotg1 { vbus-supply = <®_usb_otg_vbus>; disable-over-current; - dr_mode="otg"; + dr_mode = "otg"; status = "okay"; };
arch/arm/dts/imx8mn-beacon-kit-u-boot.dtsi +1 -1
@@ -15,7 +15,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mn-bsh-smm-s2-u-boot-common.dtsi +1 -1
@@ -16,7 +16,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi +1 -1
@@ -21,7 +21,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mn-evk.dtsi +44 -1
75 lines not on this page · raw message
arch/arm/dts/imx8mn-var-som-symphony-u-boot.dtsi +1 -1
@@ -15,7 +15,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mn-var-som-symphony.dts +3 -3
@@ -26,19 +26,19 @@ gpio-keys { compatible = "gpio-keys"; - back { + key-back { label = "Back"; gpios = <&pca9534 1 GPIO_ACTIVE_LOW>; linux,code = <KEY_BACK>; }; - home { + key-home { label = "Home"; gpios = <&pca9534 2 GPIO_ACTIVE_LOW>; linux,code = <KEY_HOME>; }; - menu { + key-menu { label = "Menu"; gpios = <&pca9534 3 GPIO_ACTIVE_LOW>; linux,code = <KEY_MENU>;
arch/arm/dts/imx8mn-venice-gw7902.dts +4 -4
@@ -39,13 +39,13 @@ gpio-keys { compatible = "gpio-keys"; - user-pb { + key-user-pb { label = "user_pb"; gpios = <&gpio 2 GPIO_ACTIVE_LOW>; linux,code = <BTN_0>; }; - user-pb1x { + key-user-pb1x { label = "user_pb1x"; linux,code = <BTN_1>; interrupt-parent = <&gsc>;
@@ -59,14 +59,14 @@ interrupts = <1>; }; - eeprom-wp { + key-eeprom-wp { label = "eeprom_wp"; linux,code = <BTN_3>; interrupt-parent = <&gsc>; interrupts = <2>; }; - tamper { + key-tamper { label = "tamper"; linux,code = <BTN_4>; interrupt-parent = <&gsc>;
arch/arm/dts/imx8mn-venice-u-boot.dtsi +1 -1
@@ -15,7 +15,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mn.dtsi +7 -6
@@ -212,7 +212,7 @@ clk_ext4: clock-ext4 { compatible = "fixed-clock"; #clock-cells = <0>; - clock-frequency= <133000000>; + clock-frequency = <133000000>; clock-output-names = "clk_ext4"; };
@@ -269,7 +269,7 @@ arm,no-tick-in-suspend; }; - soc@0 { + soc: soc@0 { compatible = "fsl,imx8mn-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>;
@@ -422,7 +422,7 @@ "ctx2_rx", "ctx2_tx", "ctx3_rx", "ctx3_tx"; firmware-name = "imx/easrc/easrc-imx8mn.bin"; - fsl,asrc-rate = <8000>; + fsl,asrc-rate = <8000>; fsl,asrc-format = <2>; status = "disabled"; };
@@ -857,6 +857,7 @@ compatible = "fsl,sec-v4.0-job-ring"; reg = <0x1000 0x1000>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; }; sec_jr1: jr@2000 {
@@ -941,7 +942,7 @@ <&clk IMX8MN_CLK_USDHC1_ROOT>; clock-names = "ipg", "ahb", "per"; fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; + fsl,tuning-step = <2>; bus-width = <4>; status = "disabled"; };
@@ -955,7 +956,7 @@ <&clk IMX8MN_CLK_USDHC2_ROOT>; clock-names = "ipg", "ahb", "per"; fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; + fsl,tuning-step = <2>; bus-width = <4>; status = "disabled"; };
@@ -969,7 +970,7 @@ <&clk IMX8MN_CLK_USDHC3_ROOT>; clock-names = "ipg", "ahb", "per"; fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; + fsl,tuning-step = <2>; bus-width = <4>; status = "disabled"; };
include/dt-bindings/interconnect/imx8mn.h new file +41 -0
41 lines not on this page · raw message
Signature · 1 line
2.35.1
PATCH 8/8 imx8mm: synchronise device tree with linux
In reply to Marcel ZiswilerFrom: Marcel Ziswiler <[email protected]>
Synchronise device tree with linux v6.0-rc1.
---
arch/arm/dts/imx8mm-beacon-baseboard.dtsi | 4 +- arch/arm/dts/imx8mm-evk.dtsi | 43 +++++++++++++++++++ arch/arm/dts/imx8mm-icore-mx8mm.dtsi | 12 +++--- arch/arm/dts/imx8mm-mx8menlo.dts | 4 +- arch/arm/dts/imx8mm-u-boot.dtsi | 2 +- arch/arm/dts/imx8mm-venice-gw700x.dtsi | 24 +++++------ arch/arm/dts/imx8mm-venice-gw7901.dts | 8 ++-- arch/arm/dts/imx8mm-venice-gw7902.dts | 10 ++--- arch/arm/dts/imx8mm-venice-gw7903.dts | 6 +-- arch/arm/dts/imx8mm-verdin.dtsi | 10 ++++- include/dt-bindings/interconnect/imx8mm.h | 50 +++++++++++++++++++++++ 11 files changed, 137 insertions(+), 36 deletions(-) create mode 100644 include/dt-bindings/interconnect/imx8mm.h
arch/arm/dts/imx8mm-beacon-baseboard.dtsi +2 -2
@@ -285,14 +285,14 @@ &usbotg1 { vbus-supply = <®_usbotg1>; disable-over-current; - dr_mode="otg"; + dr_mode = "otg"; status = "okay"; }; &usbotg2 { pinctrl-names = "default"; disable-over-current; - dr_mode="host"; + dr_mode = "host"; status = "okay"; };
arch/arm/dts/imx8mm-evk.dtsi +43 -0
67 lines not on this page · raw message
arch/arm/dts/imx8mm-icore-mx8mm.dtsi +6 -6
@@ -84,42 +84,42 @@ }; reg_buck1: buck1 { - regulator-min-microvolt = <400000>; + regulator-min-microvolt = <400000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; reg_buck2: buck2 { - regulator-min-microvolt = <400000>; + regulator-min-microvolt = <400000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; reg_buck3: buck3 { - regulator-min-microvolt = <400000>; + regulator-min-microvolt = <400000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; reg_buck4: buck4 { - regulator-min-microvolt = <400000>; + regulator-min-microvolt = <400000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; reg_buck5: buck5 { - regulator-min-microvolt = <400000>; + regulator-min-microvolt = <400000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on; }; reg_buck6: buck6 { - regulator-min-microvolt = <400000>; + regulator-min-microvolt = <400000>; regulator-max-microvolt = <1800000>; regulator-always-on; regulator-boot-on;
arch/arm/dts/imx8mm-mx8menlo.dts +2 -2
@@ -20,13 +20,13 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_led>; - user1 { + led-1 { label = "TestLed601"; gpios = <&gpio4 18 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc0"; }; - user2 { + led-2 { label = "TestLed602"; gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat";
arch/arm/dts/imx8mm-u-boot.dtsi +1 -1
@@ -9,7 +9,7 @@ }; }; -&{/soc@0} { +&soc { u-boot,dm-pre-reloc; u-boot,dm-spl; };
arch/arm/dts/imx8mm-venice-gw700x.dtsi +12 -12
@@ -16,13 +16,13 @@ gpio-keys { compatible = "gpio-keys"; - user-pb { + key-user-pb { label = "user_pb"; gpios = <&gpio 2 GPIO_ACTIVE_LOW>; linux,code = <BTN_0>; }; - user-pb1x { + key-user-pb1x { label = "user_pb1x"; linux,code = <BTN_1>; interrupt-parent = <&gsc>;
@@ -36,14 +36,14 @@ interrupts = <1>; }; - eeprom-wp { + key-eeprom-wp { label = "eeprom_wp"; linux,code = <BTN_3>; interrupt-parent = <&gsc>; interrupts = <2>; }; - tamper { + key-tamper { label = "tamper"; linux,code = <BTN_4>; interrupt-parent = <&gsc>;
@@ -286,8 +286,8 @@ regulator-name = "buck1"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <1000000>; - regulator-min-microamp = <3800000>; - regulator-max-microamp = <6800000>; + regulator-min-microamp = <3800000>; + regulator-max-microamp = <6800000>; regulator-boot-on; regulator-always-on; };
@@ -297,8 +297,8 @@ regulator-name = "buck2"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <900000>; - regulator-min-microamp = <2200000>; - regulator-max-microamp = <5200000>; + regulator-min-microamp = <2200000>; + regulator-max-microamp = <5200000>; regulator-boot-on; regulator-always-on; };
@@ -308,8 +308,8 @@ regulator-name = "buck3"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <1000000>; - regulator-min-microamp = <3800000>; - regulator-max-microamp = <6800000>; + regulator-min-microamp = <3800000>; + regulator-max-microamp = <6800000>; regulator-always-on; };
@@ -318,8 +318,8 @@ regulator-name = "buck4"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <2200000>; - regulator-max-microamp = <5200000>; + regulator-min-microamp = <2200000>; + regulator-max-microamp = <5200000>; regulator-boot-on; regulator-always-on; };
arch/arm/dts/imx8mm-venice-gw7901.dts +4 -4
@@ -38,13 +38,13 @@ gpio-keys { compatible = "gpio-keys"; - user-pb { + key-user-pb { label = "user_pb"; gpios = <&gpio 2 GPIO_ACTIVE_LOW>; linux,code = <BTN_0>; }; - user-pb1x { + key-user-pb1x { label = "user_pb1x"; linux,code = <BTN_1>; interrupt-parent = <&gsc>;
@@ -58,14 +58,14 @@ interrupts = <1>; }; - eeprom-wp { + key-eeprom-wp { label = "eeprom_wp"; linux,code = <BTN_3>; interrupt-parent = <&gsc>; interrupts = <2>; }; - tamper { + key-tamper { label = "tamper"; linux,code = <BTN_4>; interrupt-parent = <&gsc>;
arch/arm/dts/imx8mm-venice-gw7902.dts +5 -5
@@ -42,13 +42,13 @@ gpio-keys { compatible = "gpio-keys"; - user-pb { + key-user-pb { label = "user_pb"; gpios = <&gpio 2 GPIO_ACTIVE_LOW>; linux,code = <BTN_0>; }; - user-pb1x { + key-user-pb1x { label = "user_pb1x"; linux,code = <BTN_1>; interrupt-parent = <&gsc>;
@@ -62,14 +62,14 @@ interrupts = <1>; }; - eeprom-wp { + key-eeprom-wp { label = "eeprom_wp"; linux,code = <BTN_3>; interrupt-parent = <&gsc>; interrupts = <2>; }; - tamper { + key-tamper { label = "tamper"; linux,code = <BTN_4>; interrupt-parent = <&gsc>;
@@ -651,7 +651,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_gpio>; rts-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; - cts-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + cts-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; uart-has-rtscts; status = "okay"; };
arch/arm/dts/imx8mm-venice-gw7903.dts +3 -3
@@ -33,13 +33,13 @@ gpio-keys { compatible = "gpio-keys"; - user-pb { + key-user-pb { label = "user_pb"; gpios = <&gpio 2 GPIO_ACTIVE_LOW>; linux,code = <BTN_0>; }; - user-pb1x { + key-user-pb1x { label = "user_pb1x"; linux,code = <BTN_1>; interrupt-parent = <&gsc>;
@@ -53,7 +53,7 @@ interrupts = <1>; }; - eeprom-wp { + key-eeprom-wp { label = "eeprom_wp"; linux,code = <BTN_3>; interrupt-parent = <&gsc>;
arch/arm/dts/imx8mm-verdin.dtsi +9 -1
@@ -43,7 +43,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gpio_keys>; - wakeup { + key-wakeup { debounce-interval = <10>; /* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */ gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
@@ -154,6 +154,14 @@ cpu-supply = <®_vdd_arm>; }; +&cpu_alert0 { + temperature = <95000>; +}; + +&cpu_crit0 { + temperature = <105000>; +}; + &ddrc { operating-points-v2 = <&ddrc_opp_table>;
include/dt-bindings/interconnect/imx8mm.h new file +50 -0
50 lines not on this page · raw message
Signature · 1 line
2.35.1