firmware: dmi: Use the proper accessor for the version field
Subsystems (2)
Sasha Levin
maintainerPATCH 2/8 drm/amdgpu: Check num_gfx_rings for gfx v9_0 rb setup.
In reply to Sasha LevinFrom: Candice Li <[email protected]>
[ Upstream commit c351938350ab9b5e978dede2c321da43de7eb70c ]
No need to set up rb when no gfx rings.
--- drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/amd/amdgpu/gfx_v9_0.c +2 -1
@@ -1514,7 +1514,8 @@ static void gfx_v9_0_gpu_init(struct amdgpu_device *adev)gfx_v9_0_tiling_mode_table_init (adev); -gfx_v9_0_setup_rb (adev); +if (adev->gfx.num_gfx_rings) +gfx_v9_0_setup_rb (adev);gfx_v9_0_get_cu_info (adev, &adev->gfx.cu_info);/* XXX SH_MEM regs */
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 3/8 drm/radeon: add a force flush to delay work when radeon
In reply to Sasha LevinFrom: Zhenneng Li <[email protected]>
[ Upstream commit f461950fdc374a3ada5a63c669d997de4600dffe ]
Although radeon card fence and wait for gpu to finish processing current batch rings, there is still a corner case that radeon lockup work queue may not be fully flushed, and meanwhile the radeon_suspend_kms() function has called pci_set_power_state() to put device in D3hot state.
Per PCI spec rev 4.0 on 5.3.1.4.1 D3hot State.
Quoted 3 lines
Configuration and Message requests are the only TLPs accepted by a Function in the D3hot state. All other received Requests must be handled as Unsupported Requests, and all received Completions may optionally be handled as Unexpected Completions.
This issue will happen in following logs:
Unable to handle kernel paging request at virtual address 00008800e0008010
CPU 0 kworker/0:3(131): Oops 0
pc = [<ffffffff811bea5c>] ra = [<ffffffff81240844>] ps = 0000 Tainted: G W
pc is at si_gpu_check_soft_reset+0x3c/0x240
ra is at si_dma_is_lockup+0x34/0xd0
v0 = 0000000000000000 t0 = fff08800e0008010 t1 = 0000000000010000 t2 = 0000000000008010 t3 = fff00007e3c00000 t4 = fff00007e3c00258 t5 = 000000000000ffff t6 = 0000000000000001 t7 = fff00007ef078000 s0 = fff00007e3c016e8 s1 = fff00007e3c00000 s2 = fff00007e3c00018 s3 = fff00007e3c00000 s4 = fff00007fff59d80 s5 = 0000000000000000 s6 = fff00007ef07bd98 a0 = fff00007e3c00000 a1 = fff00007e3c016e8 a2 = 0000000000000008 a3 = 0000000000000001 a4 = 8f5c28f5c28f5c29 a5 = ffffffff810f4338 t8 = 0000000000000275 t9 = ffffffff809b66f8 t10 = ff6769c5d964b800 t11= 000000000000b886 pv = ffffffff811bea20 at = 0000000000000000 gp = ffffffff81d89690 sp = 00000000aa814126 Disabling lock debugging due to kernel taint Trace: [<ffffffff81240844>] si_dma_is_lockup+0x34/0xd0 [<ffffffff81119610>] radeon_fence_check_lockup+0xd0/0x290 [<ffffffff80977010>] process_one_work+0x280/0x550 [<ffffffff80977350>] worker_thread+0x70/0x7c0 [<ffffffff80977410>] worker_thread+0x130/0x7c0 [<ffffffff80982040>] kthread+0x200/0x210 [<ffffffff809772e0>] worker_thread+0x0/0x7c0 [<ffffffff80981f8c>] kthread+0x14c/0x210 [<ffffffff80911658>] ret_from_kernel_thread+0x18/0x20 [<ffffffff80981e40>] kthread+0x0/0x210 Code: ad3e0008 43f0074a ad7e0018 ad9e0020 8c3001e8 40230101 <88210000> 4821ed21
So force lockup work queue flush to fix this problem.
--- drivers/gpu/drm/radeon/radeon_device.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/gpu/drm/radeon/radeon_device.c +3 -0
@@ -1655,6 +1655,9 @@ int radeon_suspend_kms(struct drm_device *dev, bool suspend,if (r) {/* delay GPU reset to resume */ radeon_fence_driver_force_completion (rdev, i); + }else { +/* finish executing delayed work */ +flush_delayed_work (&rdev->fence_drv[i].lockup_work); } }
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 7/8 fbdev: fb_pm2fb: Avoid potential divide by zero error
In reply to Sasha LevinFrom: Letu Ren <[email protected]>
[ Upstream commit 19f953e7435644b81332dd632ba1b2d80b1e37af ]
In do_fb_ioctl() of fbmem.c, if cmd is FBIOPUT_VSCREENINFO, var will be copied from user, then go through fb_set_var() and info->fbops->fb_check_var() which could may be pm2fb_check_var(). Along the path, var->pixclock won't be modified. This function checks whether reciprocal of var->pixclock is too high. If var->pixclock is zero, there will be a divide by zero error. So, it is necessary to check whether denominator is zero to avoid crash. As this bug is found by Syzkaller, logs are listed below.
divide error in pm2fb_check_var
Call Trace: <TASK> fb_set_var+0x367/0xeb0 drivers/video/fbdev/core/fbmem.c:1015 do_fb_ioctl+0x234/0x670 drivers/video/fbdev/core/fbmem.c:1110 fb_ioctl+0xdd/0x130 drivers/video/fbdev/core/fbmem.c:1189
--- drivers/video/fbdev/pm2fb.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/video/fbdev/pm2fb.c +5 -0
@@ -614,6 +614,11 @@ static int pm2fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)return -EINVAL ; } +if (!var->pixclock) { +DPRINTK ("pixclock is zero\n" ); +return -EINVAL ; + } +if (PICOS2KHZ (var->pixclock) >PM2_MAX_PIXCLOCK ) {DPRINTK ("pixclock too high (%ldKHz)\n" ,PICOS2KHZ (var->pixclock));
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 8/8 fbdev: chipsfb: Add missing pci_disable_device() in chipsfb_pci_init()
In reply to Sasha LevinFrom: Yang Yingliang <[email protected]>
[ Upstream commit 07c55c9803dea748d17a054000cbf1913ce06399 ]
Add missing pci_disable_device() in error path in chipsfb_pci_init().
--- drivers/video/fbdev/chipsfb.c | 1 + 1 file changed, 1 insertion(+)
drivers/video/fbdev/chipsfb.c +1 -0
@@ -432,6 +432,7 @@ static int chipsfb_pci_init(struct pci_dev *dp, const struct pci_device_id *ent) err_release_fb:framebuffer_release (p); err_disable: +pci_disable_device (dp); err_out:return rc; }
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 1/8 firmware: dmi: Use the proper accessor for the version field
From: Andy Shevchenko <[email protected]>
[ Upstream commit d2139dfca361a1f5bfc4d4a23455b1a409a69cd4 ]
The byte at offset 6 represents length. Don't take it and drop it immediately by using proper accessor, i.e. get_unaligned_be24().
[JD: Change the subject to something less frightening]
--- drivers/firmware/dmi_scan.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/firmware/dmi_scan.c +1 -1
@@ -582,7 +582,7 @@ static int __init dmi_smbios3_present(const u8 *buf) {if (memcmp (buf,"_SM3_" ,5 ) ==0 && buf[6 ] <32 &&dmi_checksum (buf, buf[6 ])) { - dmi_ver =get_unaligned_be32 (buf +6 ) &0xFFFFFF ; + dmi_ver =get_unaligned_be24 (buf +7 ); dmi_num =0 ;/* No longer specified */ dmi_len =get_unaligned_le32 (buf +12 ); dmi_base =get_unaligned_le64 (buf +16 );
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 6/8 arm64/signal: Raise limit on stack frames
From: Mark Brown <[email protected]>
[ Upstream commit 7ddcaf78e93c9282b4d92184f511b4d5bee75355 ]
The signal code has a limit of 64K on the size of a stack frame that it will generate, if this limit is exceeded then a process will be killed if it receives a signal. Unfortunately with the advent of SME this limit is too small - the maximum possible size of the ZA register alone is 64K. This is not an issue for practical systems at present but is easily seen using virtual platforms.
Raise the limit to 256K, this is substantially more than could be used by any current architecture extension.
--- arch/arm64/kernel/signal.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/kernel/signal.c +1 -1
@@ -97,7 +97,7 @@ static size_t sigframe_size(struct rt_sigframe_user_layout const *user)* not taken into account. This limit is not a guarantee and is * NOT ABI. */ -#define SIGFRAME_MAXSZ SZ_64K +#define SIGFRAME_MAXSZ SZ_256Kstatic int __sigframe_alloc (struct rt_sigframe_user_layout *user,unsigned long *offset,size_t size,bool extend)
Signature · 7 lines
2.35.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Sasha Levin
maintainerPATCH 4/8 parisc: ccio-dma: Handle kmalloc failure in ccio_init_resources()
In reply to Sasha LevinFrom: Li Qiong <[email protected]>
[ Upstream commit d46c742f827fa2326ab1f4faa1cccadb56912341 ]
As the possible failure of the kmalloc(), it should be better to fix this error path, check and return '-ENOMEM' error code.
--- drivers/parisc/ccio-dma.c | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)
drivers/parisc/ccio-dma.c +8 -3
@@ -1416,15 +1416,17 @@ ccio_init_resource(struct resource *res, char *name, void __iomem *ioaddr) } } -static void __init ccio_init_resources (struct ioc *ioc) +static int __init ccio_init_resources (struct ioc *ioc) {struct resource *res = ioc->mmio_region;char *name =kmalloc (14 ,GFP_KERNEL ); - +if (unlikely (!name)) +return -ENOMEM ;snprintf (name,14 ,"GSC Bus [%d/]" , ioc->hw_path);ccio_init_resource (res, name, &ioc->ioc_regs->io_io_low);ccio_init_resource (res +1 , name, &ioc->ioc_regs->io_io_low_hv); +return 0 ; } static int new_ioc_area(struct resource *res, unsigned long size,
@@ -1578,7 +1580,10 @@ static int __init ccio_probe(struct parisc_device *dev)return -ENOMEM ; }ccio_ioc_init (ioc); -ccio_init_resources (ioc); +if (ccio_init_resources (ioc)) { +kfree (ioc); +return -ENOMEM ; + } hppa_dma_ops = &ccio_ops; dev->dev.platform_data =kzalloc (sizeof (struct pci_hba_data ),GFP_KERNEL );
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 5/8 parisc: Add runtime check to prevent PA2.0 kernels on PA1.x machines
In reply to Sasha LevinFrom: Helge Deller <[email protected]>
[ Upstream commit 591d2108f3abc4db9f9073cae37cf3591fd250d6 ]
If a 32-bit kernel was compiled for PA2.0 CPUs, it won't be able to run on machines with PA1.x CPUs. Add a check and bail out early if a PA1.x machine is detected.
--- arch/parisc/kernel/head.S | 43 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 42 insertions(+), 1 deletion(-)
arch/parisc/kernel/head.S +42 -1
@@ -22,7 +22,7 @@ #include <linux/linkage.h> #include <linux/init.h> - .level PA_ASM_LEVEL + .level 1.1 __INITDATA ENTRY(boot_args)
@@ -69,6 +69,47 @@ $bss_loop: stw,ma %arg2,4(%r1) stw,ma %arg3,4(%r1) +#if !defined(CONFIG_64BIT) && defined(CONFIG_PA20) + /* This 32-bit kernel was compiled for PA2.0 CPUs. Check current CPU + * and halt kernel if we detect a PA1.x CPU. */ + ldi 32,%r10 + mtctl %r10,%cr11 + .level 2.0 + mfctl,w %cr11,%r10 + .level 1.1 + comib,<>,n 0,%r10,$cpu_ok + + load32 PA(msg1),%arg0 + ldi msg1_end-msg1,%arg1 +$iodc_panic: + copy %arg0, %r10 + copy %arg1, %r11 + load32 PA(init_stack),%sp +#define MEM_CONS 0x3A0 + ldw MEM_CONS+32(%r0),%arg0 // HPA + ldi ENTRY_IO_COUT,%arg1 + ldw MEM_CONS+36(%r0),%arg2 // SPA + ldw MEM_CONS+8(%r0),%arg3 // layers + load32 PA(__bss_start),%r1 + stw %r1,-52(%sp) // arg4 + stw %r0,-56(%sp) // arg5 + stw %r10,-60(%sp) // arg6 = ptr to text + stw %r11,-64(%sp) // arg7 = len + stw %r0,-68(%sp) // arg8 + load32 PA(.iodc_panic_ret), %rp + ldw MEM_CONS+40(%r0),%r1 // ENTRY_IODC + bv,n (%r1) +.iodc_panic_ret: + b . /* wait endless with ... */ + or %r10,%r10,%r10 /* qemu idle sleep */ +msg1: .ascii "Can't boot kernel which was built for PA8x00 CPUs on this machine.\r\n" +msg1_end: + +$cpu_ok: +#endif + + .level PA_ASM_LEVEL + /* Initialize startup VM. Just map first 16/32 MB of memory */ load32 PA(swapper_pg_dir),%r4 mtctl %r4,%cr24 /* Initialize kernel root pointer */
Signature · 1 line
2.35.1