dt-bindings: dsa: lan9303: Add lan9303 yaml
Subsystems (4)
PATCH v2 1/1 dt-bindings: dsa: lan9303: Add lan9303 yaml
Adding the dt binding yaml for the lan9303 3-port ethernet switch. The microchip lan9354 3-port ethernet switch will also use the same binding.
Signed-off-by Jerry Ray <[email protected]>
---v1->v2:
- fixed dt_binding_check warning
- added max-speed setting on the switches 10/100 ports.
--- .../devicetree/bindings/net/dsa/lan9303.txt | 100 +------------ .../bindings/net/dsa/microchip,lan9303.yaml | 131 ++++++++++++++++++ MAINTAINERS | 8 ++ 3 files changed, 140 insertions(+), 99 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
Documentation/devicetree/bindings/net/dsa/lan9303.txt +1 -99
@@ -1,102 +1,4 @@ SMSC/MicroChip LAN9303 three port ethernet switch ------------------------------------------------- -Required properties: - -- compatible: should be - - "smsc,lan9303-i2c" for I2C managed mode - or - - "smsc,lan9303-mdio" for mdio managed mode - -Optional properties: - -- reset-gpios: GPIO to be used to reset the whole device -- reset-duration: reset duration in milliseconds, defaults to 200 ms - -Subnodes: - -The integrated switch subnode should be specified according to the binding -described in dsa/dsa.txt. The CPU port of this switch is always port 0. - -Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is -configured to use 1/2/3 instead. This hardware configuration will be -auto-detected and mapped accordingly. - -Example: - -I2C managed mode: - - master: masterdevice@X { - - fixed-link { /* RMII fixed link to LAN9303 */ - speed = <100>; - full-duplex; - }; - }; - - switch: switch@a { - compatible = "smsc,lan9303-i2c"; - reg = <0xa>; - reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; - reset-duration = <200>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { /* RMII fixed link to master */ - reg = <0>; - label = "cpu"; - ethernet = <&master>; - }; - - port@1 { /* external port 1 */ - reg = <1>; - label = "lan1"; - }; - - port@2 { /* external port 2 */ - reg = <2>; - label = "lan2"; - }; - }; - }; - -MDIO managed mode: - - master: masterdevice@X { - phy-handle = <&switch>; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - switch: switch-phy@0 { - compatible = "smsc,lan9303-mdio"; - reg = <0>; - reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; - reset-duration = <100>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "cpu"; - ethernet = <&master>; - }; - - port@1 { /* external port 1 */ - reg = <1>; - label = "lan1"; - }; - - port@2 { /* external port 2 */ - reg = <2>; - label = "lan2"; - }; - }; - }; - }; - }; +See Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml for the documentation.
Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml new file +131 -0
131 lines not on this page · raw message
MAINTAINERS +8 -0
@@ -13385,6 +13385,14 @@ L: [email protected] S: Maintained F: drivers/net/ethernet/microchip/lan743x_* +MICROCHIP LAN9303/LAN9354 ETHERNET SWITCH DRIVER +M: Jerry Ray <[email protected]> +M: [email protected] +L: [email protected] +S: Maintained +F: Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml +F: drivers/net/dsa/lan9303* + MICROCHIP LAN966X ETHERNET DRIVER M: Horatiu Vultur <[email protected]> M: [email protected]
Signature · 1 line
2.25.1
Andrew Lunn
maintainerDocumentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml line 68
Quoted 11 lines
Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml new file +11
-0+ compatible = "smsc,lan9303-mdio"; + dsa,member = <0 0>; + reg = <0>; + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phy-mode = "rmii"; + ethernet = <ðernet>; + label = "cpu";
The cpu label is never used, and i think Vladimir has been removing them from bindings and DT blobs. So your example probably should not have it.
Andrew