Bug in ext2load?
I think I've found a bug in the ext2load command. When the file being read is a sparse file, the command fails as in this example.
=> ext2load usb 0:1 $load_addr firmware_ls2088ardb_norboot.img fs_devread read outside partition 60063712
Failed to load 'firmware_ls2088ardb_norboot.img'
However, if the same image file is copied to the USB flash drive on the build machine so that it is not sparse, that is, with "cp --sparse=never ...", then the ext2load command on the target machine succeeds.
I think the problem may be in the ext4fs_read_file() command in fs/ext4/ext4fs.c. That is the only function I see in the path from the ext2load command to the error message that does anything explicitly with blocks. Also, this comment at the top of that function suggests that someone tried to optimize the reading of the file and may have missed some sparse-file condition.
/*
* Taken from openmoko-kernel mailing list: By Andy green
* Optimized read file API : collects and defers contiguous sector
* reads into one potentially more efficient larger sequential read action */
However, I did not try to debug the problem further, as using "cp --sparse=never" is an adequate workaround and I have more pressing work to do.
It appears that the ext2load command runs off the end of the list of blocks in the inode and tries to read beyond the end of the partition.
=> usb storage
Device 0: Vendor: USB Rev: 1.00 Prod: SanDisk 3.2Gen1
Type: Removable Hard Disk
Capacity: 29328.0 MB = 28.6 GB (60063744 x 512)
Note that the drive capacity is 32 sectors less than the sector reported in the error message. According to the part list command, the partition starts at sector 32, and the number of sectors available matches the number reported in the error message, so this adds up.
=> part list usb 0
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 32 60063712 eca4cd09-01 83
This error happens with two versions of U-Boot:
U-Boot 2016.092.0+ga06b209 (Mar 30 2017 - 01:15:01 +0800)
U-Boot 2021.04-ge2eba0cd58 (Aug 27 2021 - 22:23:21 +0800)The last change to fs/ext4/ext4fs.c appears to have been made at commit e6f6f9e648 (2020-05-10).
Let me know if you need any addtional information or if I missed something and am wrong about all this.
Regards,
Gary
+Heinrich Schuchardt
Quoted 66 lines · Gary Johnson
I think I've found a bug in the ext2load command. When the file being read is a sparse file, the command fails as in this example.
=> ext2load usb 0:1 $load_addr firmware_ls2088ardb_norboot.img
fs_devreadread outside partition 60063712
Failed to load 'firmware_ls2088ardb_norboot.img'However, if the same image file is copied to the USB flash drive on the build machine so that it is not sparse, that is, with "cp --sparse=never ...", then the ext2load command on the target machine succeeds.
I think the problem may be in the
ext4fs_read_file()command infs/ext4/ext4fs.c. That is the only function I see in the path from the ext2load command to the error message that does anything explicitly with blocks. Also, this comment at the top of that function suggests that someone tried to optimize the reading of the file and may have missed some sparse-file condition./*
* Taken from openmoko-kernel mailing list: By Andy green
* Optimized read file API : collects and defers contiguous sector
* reads into one potentially more efficient larger sequential read action */However, I did not try to debug the problem further, as using "cp --sparse=never" is an adequate workaround and I have more pressing work to do.
It appears that the ext2load command runs off the end of the list of blocks in the inode and tries to read beyond the end of the partition.
=> usb storage
Device 0: Vendor: USB Rev: 1.00 Prod: SanDisk 3.2Gen1
Type: Removable Hard Disk
Capacity: 29328.0 MB = 28.6 GB (60063744 x 512)Note that the drive capacity is 32 sectors less than the sector reported in the error message. According to the part list command, the partition starts at sector 32, and the number of sectors available matches the number reported in the error message, so this adds up.
=> part list usb 0
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 32 60063712 eca4cd09-01 83This error happens with two versions of U-Boot:
U-Boot 2016.092.0+ga06b209 (Mar 30 2017 - 01:15:01 +0800) U-Boot 2021.04-ge2eba0cd58 (Aug 27 2021 - 22:23:21 +0800)The last change to
fs/ext4/ext4fs.cappears to have been made at commite6f6f9e648(2020-05-10).Let me know if you need any addtional information or if I missed something and am wrong about all this.
Regards,
Gary
Quoted 5 lines · Simon Glass
+Heinrich Schuchardt
Quoted 2 lines · Gary Johnson
I think I've found a bug in the ext2load command. When the file
According to the description below the bug is not in the command but in the file-system driver.
Function read_allocated_block() tries to implement handling of sparse files. According to comments it is a copy from GRUB. GRUB has tried to fix an error for sparse files with commit 1e5ed5f5f5a ("fs/ext2: Fix handling of missing sparse extent leafs.")
Maybe we could try to upgrade to GRUB's current code.
Quoted 58 lines
Quoted 58 lines
being read is a sparse file, the command fails as in this example.
=> ext2load usb 0:1 $load_addr firmware_ls2088ardb_norboot.img
fs_devreadread outside partition 60063712
Failed to load 'firmware_ls2088ardb_norboot.img'However, if the same image file is copied to the USB flash drive on the build machine so that it is not sparse, that is, with "cp --sparse=never ...", then the ext2load command on the target machine succeeds.
I think the problem may be in the
ext4fs_read_file()command infs/ext4/ext4fs.c. That is the only function I see in the path from the ext2load command to the error message that does anything explicitly with blocks. Also, this comment at the top of that function suggests that someone tried to optimize the reading of the file and may have missed some sparse-file condition./*
* Taken from openmoko-kernel mailing list: By Andy green
* Optimized read file API : collects and defers contiguous sector
* reads into one potentially more efficient larger sequential read action */However, I did not try to debug the problem further, as using "cp --sparse=never" is an adequate workaround and I have more pressing work to do.
It appears that the ext2load command runs off the end of the list of blocks in the inode and tries to read beyond the end of the partition.
=> usb storage
Device 0: Vendor: USB Rev: 1.00 Prod: SanDisk 3.2Gen1
Type: Removable Hard Disk
Capacity: 29328.0 MB = 28.6 GB (60063744 x 512)Note that the drive capacity is 32 sectors less than the sector reported in the error message. According to the part list command, the partition starts at sector 32, and the number of sectors available matches the number reported in the error message, so this adds up.
=> part list usb 0
Partition Map for USB device 0 -- Partition Type: DOS
Part Start Sector Num Sectors UUID Type
1 32 60063712 eca4cd09-01 83This error happens with two versions of U-Boot:
U-Boot 2016.092.0+ga06b209 (Mar 30 2017 - 01:15:01 +0800) U-Boot 2021.04-ge2eba0cd58 (Aug 27 2021 - 22:23:21 +0800)The last change to
fs/ext4/ext4fs.cappears to have been made at commite6f6f9e648(2020-05-10).
Quoted 6 lines
Quoted 6 lines
Let me know if you need any addtional information or if I missed something and am wrong about all this.
Regards,
Gary
Here is another error report for ext4:
[BUG] ext4: the load command on an EXT4 partition leads to errors due to unaligned buffers
https://lists.denx.de/pipermail/u-boot/2021-January/437180.html
Unfortunately filesystems cbfs, fat, ext4, reiserfs, zfs don't have maintainers.
Best regards
Heinrich