ARM: dts: imx7d-sdb: config the max pressure for tsc2046
Subsystems (3)
Sasha Levin
maintainerPATCH 7/11 ARM: dts: imx6sll: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit 7492a83ed9b7a151e2dd11d64b06da7a7f0fa7f9 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6sll.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6sll.dtsi +3 -0
@@ -131,6 +131,9 @@ soc { ocram: sram@900000 { compatible = "mmio-sram"; reg = <0x00900000 0x20000>; + ranges = <0 0x00900000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; }; L2: l2-cache@a02000 {
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 4/11 ARM: dts: imx6dl: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit f5848b95633d598bacf0500e0108dc5961af88c0 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6dl.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6dl.dtsi +3 -0
@@ -81,6 +81,9 @@ soc { ocram: sram@900000 { compatible = "mmio-sram"; reg = <0x00900000 0x20000>; + ranges = <0 0x00900000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 8/11 ARM: dts: imx6sx: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit 415432c008b2bce8138841356ba444631cabaa50 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/imx6sx.dtsi +6 -0
@@ -167,12 +167,18 @@ soc { ocram_s: sram@8f8000 { compatible = "mmio-sram"; reg = <0x008f8000 0x4000>; + ranges = <0 0x008f8000 0x4000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6SX_CLK_OCRAM_S>; }; ocram: sram@900000 { compatible = "mmio-sram"; reg = <0x00900000 0x20000>; + ranges = <0 0x00900000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6SX_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 10/11 arm64: dts: uniphier: Add USB-device support for PXs3 reference board
In reply to Sasha LevinFrom: Kunihiko Hayashi <[email protected]>
[ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
PXs3 reference board can change each USB port 0 and 1 to device mode with jumpers. Prepare devicetree sources for USB port 0 and 1.
This specifies dr_mode, pinctrl, and some quirks and removes nodes for unused phys and vbus-supply properties.
--- arch/arm/boot/dts/uniphier-pinctrl.dtsi | 10 +++++ arch/arm64/boot/dts/socionext/Makefile | 4 +- .../socionext/uniphier-pxs3-ref-gadget0.dts | 41 +++++++++++++++++++ .../socionext/uniphier-pxs3-ref-gadget1.dts | 40 ++++++++++++++++++ 4 files changed, 94 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
arch/arm/boot/dts/uniphier-pinctrl.dtsi +10 -0
@@ -156,11 +156,21 @@ pinctrl_usb0: usb0 { function = "usb0"; }; + pinctrl_usb0_device: usb0-device { + groups = "usb0_device"; + function = "usb0"; + }; + pinctrl_usb1: usb1 { groups = "usb1"; function = "usb1"; }; + pinctrl_usb1_device: usb1-device { + groups = "usb1_device"; + function = "usb1"; + }; + pinctrl_usb2: usb2 { groups = "usb2"; function = "usb2";
arch/arm64/boot/dts/socionext/Makefile +3 -1
@@ -4,4 +4,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ld11-ref.dtb \ uniphier-ld20-global.dtb \ uniphier-ld20-ref.dtb \ - uniphier-pxs3-ref.dtb + uniphier-pxs3-ref.dtb \ + uniphier-pxs3-ref-gadget0.dtb \ + uniphier-pxs3-ref-gadget1.dtb
arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts new file +41 -0
41 lines not on this page · raw message
arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts new file +40 -0
@@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// +// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1) +// +// Copyright (C) 2021 Socionext Inc. +// Author: Kunihiko Hayashi <[email protected]> + +/dts-v1/; +#include "uniphier-pxs3-ref.dts" + +/ { + model = "UniPhier PXs3 Reference Board (USB-Device #1)"; +}; + +/* I2C3 pinctrl is shared with USB*VBUSIN */ +&i2c3 { + status = "disabled"; +}; + +&usb1 { + status = "okay"; + dr_mode = "peripheral"; + pinctrl-0 = <&pinctrl_usb1_device>; + snps,dis_enblslpm_quirk; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,usb2_gadget_lpm_disable; + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb1_hsphy0>, <&usb1_ssphy0>; +}; + +&usb1_hsphy0 { + /delete-property/ vbus-supply; +}; + +&usb1_ssphy0 { + /delete-property/ vbus-supply; +}; + +/delete-node/ &usb1_hsphy1;
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 11/11 selftests/cpu-hotplug: Use return instead of exit
In reply to Sasha LevinFrom: Zhao Gongyi <[email protected]>
[ Upstream commit 972cf4ce51ef5532d56822af17defb148aac0ccb ]
Some cpus will be left in offline state when online function exits in some error conditions. Use return instead of exit to fix it.
--- .../selftests/cpu-hotplug/cpu-on-off-test.sh | 13 ++++++++----- 1 file changed, 8 insertions(+), 5 deletions(-)
tools/testing/selftests/cpu-hotplug/cpu-on-off-test.sh +8 -5
@@ -4,6 +4,7 @@ SYSFS= # Kselftest framework requirement - SKIP code is 4. ksft_skip=4 +retval=0 prerequisite() {
@@ -102,10 +103,10 @@ online_cpu_expect_success() if ! online_cpu $cpu; then echo $FUNCNAME $cpu: unexpected fail >&2 - exit 1 + retval=1 elif ! cpu_is_online $cpu; then echo $FUNCNAME $cpu: unexpected offline >&2 - exit 1 + retval=1 fi }
@@ -128,10 +129,10 @@ offline_cpu_expect_success() if ! offline_cpu $cpu; then echo $FUNCNAME $cpu: unexpected fail >&2 - exit 1 + retval=1 elif ! cpu_is_offline $cpu; then echo $FUNCNAME $cpu: unexpected offline >&2 - exit 1 + retval=1 fi }
@@ -201,7 +202,7 @@ if [ $allcpus -eq 0 ]; then offline_cpu_expect_success $present_max online_cpu $present_max fi - exit 0 + exit $retval else echo "Full scope test: all hotplug cpus" echo -e "\t online all offline cpus"
@@ -291,3 +292,5 @@ done echo 0 > $NOTIFIER_ERR_INJECT_DIR/actions/CPU_DOWN_PREPARE/error /sbin/modprobe -q -r cpu-notifier-error-inject + +exit $retval
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 2/11 soc: mediatek: Let PMIC Wrapper and SCPSYS depend on OF
In reply to Sasha LevinFrom: Jean Delvare <[email protected]>
[ Upstream commit 2778caedb5667239823a29148dfc48b26a8b3c2a ]
With the following configuration options:CONFIG_OF is not setCONFIG_MTK_PMIC_WRAP=yCONFIG_MTK_SCPSYS=y
we get the following build warnings:
CC drivers/soc/mediatek/mtk-pmic-wrap.odrivers/soc/mediatek/mtk-pmic-wrap.c:2138:34: warning: ‘of_pwrap_match_tbl’ defined but not used [-Wunused-const-variable=] drivers/soc/mediatek/mtk-pmic-wrap.c:1953:34: warning: ‘of_slave_match_tbl’ defined but not used [-Wunused-const-variable=]
CC drivers/soc/mediatek/mtk-scpsys.odrivers/soc/mediatek/mtk-scpsys.c:1084:34: warning: ‘of_scpsys_match_tbl’ defined but not used [-Wunused-const-variable=]
Looking at the code, both drivers can only bind to OF-defined device nodes, so these drivers are useless without OF and should therefore depend on it.
Also drop of_match_ptr() from both drivers. We already know what it will resolve to, so we might as well save cpp some work.
Developers or QA teams who wish to test-build the code can still do so by enabling CONFIG_OF, which is available on all architectures and has no dependencies.
--- drivers/soc/mediatek/Kconfig | 2 ++ drivers/soc/mediatek/mtk-pmic-wrap.c | 2 +- drivers/soc/mediatek/mtk-scpsys.c | 2 +- 3 files changed, 4 insertions(+), 2 deletions(-)
drivers/soc/mediatek/Kconfig +2 -0
@@ -15,6 +15,7 @@ config MTK_INFRACFG config MTK_PMIC_WRAP tristate "MediaTek PMIC Wrapper Support" depends on RESET_CONTROLLER + depends on OF select REGMAP help Say yes here to add support for MediaTek PMIC Wrapper found
@@ -24,6 +25,7 @@ config MTK_PMIC_WRAP config MTK_SCPSYS bool "MediaTek SCPSYS Support" default ARCH_MEDIATEK + depends on OF select REGMAP select MTK_INFRACFG select PM_GENERIC_DOMAINS if PM
drivers/soc/mediatek/mtk-pmic-wrap.c +1 -1
@@ -1672,7 +1672,7 @@ static int pwrap_probe(struct platform_device *pdev)static struct platform_driver pwrap_drv = { .driver = { .name ="mt-pmic-pwrap" , - .of_match_table =of_match_ptr (of_pwrap_match_tbl), + .of_match_table = of_pwrap_match_tbl, }, .probe = pwrap_probe, };
drivers/soc/mediatek/mtk-scpsys.c +1 -1
@@ -1071,7 +1071,7 @@ static struct platform_driver scpsys_drv = { .name = "mtk-scpsys", .suppress_bind_attrs = true, .owner = THIS_MODULE, - .of_match_table = of_match_ptr(of_scpsys_match_tbl), + .of_match_table = of_scpsys_match_tbl, }, };builtin_platform_driver (scpsys_drv);
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 1/11 ARM: dts: imx7d-sdb: config the max pressure for tsc2046
From: Haibo Chen <[email protected]>
[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]
Use the general touchscreen method to config the max pressure for touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for ABS_PRESSURE, when config the same max and min value, weston will meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen [17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE [17:19:39.183] event1 - ADS7846 Touchscreen: was rejected [17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator could not load cursor 'dnd-move' could not load cursor 'dnd-copy' could not load cursor 'dnd-none' No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max" belong to the deprecated properties, so remove them. Also for "ti,x-min", "ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default value in driver, so are redundant, also remove here.
--- arch/arm/boot/dts/imx7d-sdb.dts | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-)
arch/arm/boot/dts/imx7d-sdb.dts +1 -6
@@ -163,12 +163,7 @@ tsc2046@0 { interrupt-parent = <&gpio2>; interrupts = <29 0>; pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>; - ti,x-min = /bits/ 16 <0>; - ti,x-max = /bits/ 16 <0>; - ti,y-min = /bits/ 16 <0>; - ti,y-max = /bits/ 16 <0>; - ti,pressure-max = /bits/ 16 <0>; - ti,x-plate-ohms = /bits/ 16 <400>; + touchscreen-max-pressure = <255>; wakeup-source; }; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 5/11 ARM: dts: imx6qp: add missing properties for sram
From: Alexander Stein <[email protected]>
[ Upstream commit 088fe5237435ee2f7ed4450519b2ef58b94c832f ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property sram@940000: '#size-cells' is a required property sram@940000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6qp.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/imx6qp.dtsi +6 -0
@@ -9,12 +9,18 @@ soc { ocram2: sram@940000 { compatible = "mmio-sram"; reg = <0x00940000 0x20000>; + ranges = <0 0x00940000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; }; ocram3: sram@960000 { compatible = "mmio-sram"; reg = <0x00960000 0x20000>; + ranges = <0 0x00960000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 9/11 ARM: orion: fix include path
In reply to Sasha LevinFrom: Arnd Bergmann <[email protected]>
[ Upstream commit 63872304bdb3decd5454f4dd210c25395278ed13 ]
Now that CONFIG_ARCH_MULTIPLATFORM can be disabled anywhere, there is a build failure for plat-orion:
arch/arm/plat-orion/irq.c:19:10: fatal error: plat/irq.h: No such file or directory
Make the include path unconditional.
--- arch/arm/plat-orion/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/plat-orion/Makefile +1 -1
@@ -1,7 +1,7 @@ # # Makefile for the linux kernel. # -ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include +ccflags-y := -I$(srctree)/$(src)/include orion-gpio-$(CONFIG_GPIOLIB) += gpio.o obj-$(CONFIG_PLAT_ORION_LEGACY) += irq.o pcie.o time.o common.o mpp.o
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 3/11 ARM: dts: imx6q: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit b11d083c5dcec7c42fe982c854706d404ddd3a5f ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6q.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6q.dtsi +3 -0
@@ -158,6 +158,9 @@ soc { ocram: sram@900000 { compatible = "mmio-sram"; reg = <0x00900000 0x40000>; + ranges = <0 0x00900000 0x40000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6QDL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 6/11 ARM: dts: imx6sl: add missing properties for sram
In reply to Sasha LevinFrom: Alexander Stein <[email protected]>
[ Upstream commit 60c9213a1d9941a8b33db570796c3f9be8984974 ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property sram@900000: '#size-cells' is a required property sram@900000: 'ranges' is a required property
--- arch/arm/boot/dts/imx6sl.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/imx6sl.dtsi +3 -0
@@ -118,6 +118,9 @@ soc { ocram: sram@900000 { compatible = "mmio-sram"; reg = <0x00900000 0x20000>; + ranges = <0 0x00900000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; clocks = <&clks IMX6SL_CLK_OCRAM>; };
Signature · 1 line
2.35.1
Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board
In reply to Sasha LevinHi!
Quoted 9 lines
From: Kunihiko Hayashi <[email protected]>
[ Upstream commit
19fee1a1096d21ab1f1e712148b5417bda2939a2]PXs3 reference board can change each USB port 0 and 1 to device mode with jumpers. Prepare devicetree sources for USB port 0 and 1.
This specifies
dr_mode, pinctrl, and some quirks and removes nodes for unused phys and vbus-supply properties.
Why was this autoselected? It is a new feature, not a bugfix.
Best regards,
Pavel
Quoted 6 lines
arch/arm/boot/dts/uniphier-pinctrl.dtsi | 10 +++++ arch/arm64/boot/dts/socionext/Makefile | 4 +- .../socionext/uniphier-pxs3-ref-gadget0.dts | 41 +++++++++++++++++++ .../socionext/uniphier-pxs3-ref-gadget1.dts | 40 ++++++++++++++++++ 4 files changed, 94 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board
Quoted 6 lines · Pavel Machek
Hi!
Quoted 4 lines
From: Kunihiko Hayashi <[email protected]>
[ Upstream commit
19fee1a1096d21ab1f1e712148b5417bda2939a2]
Quoted 7 lines
Quoted 5 lines
PXs3 reference board can change each USB port 0 and 1 to device mode with jumpers. Prepare devicetree sources for USB port 0 and 1.
This specifies
dr_mode, pinctrl, and some quirks and removes nodes for unused phys and vbus-supply properties.Why was this autoselected? It is a new feature, not a bugfix.
It also caused a regression now according to the build bots. I have not checked, but I assume there are some other patches that this depends on.
Arnd
Greg KH
maintainerRe: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board
Quoted 10 lines · Arnd Bergmann
Quoted 9 lines · Pavel Machek
Hi!
Quoted 7 lines
From: Kunihiko Hayashi <[email protected]>
[ Upstream commit
19fee1a1096d21ab1f1e712148b5417bda2939a2]PXs3 reference board can change each USB port 0 and 1 to device mode with jumpers. Prepare devicetree sources for USB port 0 and 1.
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
This specifies
dr_mode, pinctrl, and some quirks and removes nodes for unused phys and vbus-supply properties.Why was this autoselected? It is a new feature, not a bugfix.
It also caused a regression now according to the build bots. I have not checked, but I assume there are some other patches that this depends on.
Ok, let me go drop this from all trees now, thanks.
greg k-h
Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board
Quoted 15 lines · Greg KH
Quoted 11 lines · Arnd Bergmann
Quoted 10 lines · Pavel Machek
Hi!
Quoted 8 lines
From: Kunihiko Hayashi <[email protected]>
[ Upstream commit
19fee1a1096d21ab1f1e712148b5417bda2939a2]PXs3 reference board can change each USB port 0 and 1 to device mode with jumpers. Prepare devicetree sources for USB port 0 and 1.
This specifies
dr_mode, pinctrl, and some quirks and removes nodesfor
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
unused phys and vbus-supply properties.
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
Why was this autoselected? It is a new feature, not a bugfix.
It also caused a regression now according to the build bots. I have not checked, but I assume there are some other patches that this depends on.
Ok, let me go drop this from all trees now, thanks.
Sorry for late.
Right, this is not a "fixes" patch, so please drop it from stable.
Thank you,
---
Best Regards
Kunihiko Hayashi
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel