Skip to contentSkip to conversation

AM64x Disable Incomplete DT Nodes

PATCH Applied Andrew Davis 4 participants 14 messages Oct 17, 2022 – Oct 28, 2022

Subsystems (2)
lore
Share & tools
lore
#8 lore raw

PATCH 8/10 arm64: dts: ti: k3-am64: Enable MDIO nodes at the board level

In reply to Andrew Davis

MDIO nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with a pinmux.

As the attached PHY is only known about at the board integration level, these nodes should only be enabled when provided with this information.

Disable the MDIO nodes (in both CPSW and ICSSG) in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 3 +++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 9 +--------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 9 +--------
 3 files changed, 5 insertions(+), 16 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +3 -0
index b193f88a7a0f..7ea07f7fe5a2 100644
@@ -552,6 +552,7 @@ cpsw3g_mdio: mdio@f00 {
 			clocks = <&k3_clks 13 0>;
 			clock-names = "fck";
 			bus_freq = <1000000>;
+			status = "disabled";
 		};
 
 		cpts@3d000 {
@@ -1168,6 +1169,7 @@ icssg0_mdio: mdio@32400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			bus_freq = <1000000>;
+			status = "disabled";
 		};
 	};
 
@@ -1308,6 +1310,7 @@ icssg1_mdio: mdio@32400 {
 			clocks = <&k3_clks 82 0>;
 			clock-names = "fck";
 			bus_freq = <1000000>;
+			status = "disabled";
 		};
 	};
 
arch/arm64/boot/dts/ti/k3-am642-evm.dts +1 -8
index 2319ba4f5ae3..9a3bf852810c 100644
@@ -440,6 +440,7 @@ &cpsw_port2 {
 };
 
 &cpsw3g_mdio {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio1_pins_default>;
 
@@ -575,14 +576,6 @@ &ecap0 {
 	pinctrl-0 = <&main_ecap0_pins_default>;
 };
 
-&icssg0_mdio {
-	status = "disabled";
-};
-
-&icssg1_mdio {
-	status = "disabled";
-};
-
 &main_mcan0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mcan0_pins_default>;
arch/arm64/boot/dts/ti/k3-am642-sk.dts +1 -8
index c1d634647027..451e1483f3e4 100644
@@ -454,6 +454,7 @@ &cpsw_port2 {
 };
 
 &cpsw3g_mdio {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio1_pins_default>;
 
@@ -566,14 +567,6 @@ &ecap0 {
 	pinctrl-0 = <&main_ecap0_pins_default>;
 };
 
-&icssg0_mdio {
-	status = "disabled";
-};
-
-&icssg1_mdio {
-	status = "disabled";
-};
-
 &main_mcan0 {
 	status = "disabled";
 };
Signature · 1 line
2.37.3
#4 lore raw

PATCH 4/10 arm64: dts: ti: k3-am64: Enable EPWM nodes at the board level

In reply to Andrew Davis

EPWM nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information.

As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the EPWM nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi |  9 +++++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 36 -------------------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 44 ------------------------
 3 files changed, 9 insertions(+), 80 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +9 -0
index 375078ca4fdd..672575f44529 100644
@@ -898,6 +898,7 @@ epwm0: pwm@23000000 {
 		power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm1: pwm@23010000 {
@@ -907,6 +908,7 @@ epwm1: pwm@23010000 {
 		power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm2: pwm@23020000 {
@@ -916,6 +918,7 @@ epwm2: pwm@23020000 {
 		power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm3: pwm@23030000 {
@@ -925,6 +928,7 @@ epwm3: pwm@23030000 {
 		power-domains = <&k3_pds 89 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 3>, <&k3_clks 89 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm4: pwm@23040000 {
@@ -934,6 +938,7 @@ epwm4: pwm@23040000 {
 		power-domains = <&k3_pds 90 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 4>, <&k3_clks 90 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm5: pwm@23050000 {
@@ -943,6 +948,7 @@ epwm5: pwm@23050000 {
 		power-domains = <&k3_pds 91 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 5>, <&k3_clks 91 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm6: pwm@23060000 {
@@ -952,6 +958,7 @@ epwm6: pwm@23060000 {
 		power-domains = <&k3_pds 92 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 6>, <&k3_clks 92 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm7: pwm@23070000 {
@@ -961,6 +968,7 @@ epwm7: pwm@23070000 {
 		power-domains = <&k3_pds 93 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 7>, <&k3_clks 93 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	epwm8: pwm@23080000 {
@@ -970,6 +978,7 @@ epwm8: pwm@23080000 {
 		power-domains = <&k3_pds 94 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&epwm_tbclk 8>, <&k3_clks 94 0>;
 		clock-names = "tbclk", "fck";
+		status = "disabled";
 	};
 
 	ecap0: pwm@23100000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +0 -36
index 12d971c3bc3a..cef3afa10c39 100644
@@ -580,42 +580,6 @@ &ecap2 {
 	status = "disabled";
 };
 
-&epwm0 {
-	status = "disabled";
-};
-
-&epwm1 {
-	status = "disabled";
-};
-
-&epwm2 {
-	status = "disabled";
-};
-
-&epwm3 {
-	status = "disabled";
-};
-
-&epwm4 {
-	status = "disabled";
-};
-
-&epwm5 {
-	status = "disabled";
-};
-
-&epwm6 {
-	status = "disabled";
-};
-
-&epwm7 {
-	status = "disabled";
-};
-
-&epwm8 {
-	status = "disabled";
-};
-
 &icssg0_mdio {
 	status = "disabled";
 };
arch/arm64/boot/dts/ti/k3-am642-sk.dts +0 -44

50 lines not on this page · raw message

Signature · 1 line
2.37.3
#10 lore raw

PATCH 10/10 arm64: dts: ti: k3-am64: Enable GPMC and ELM nodes at the board level

In reply to Andrew Davis

The GPMC node defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless it is extended with pinmux information.

As the pinmux is only known at the board integration level, this node should only be enabled when provided with this information.

Disable the GPMC node in the dtsi file. Since the ELM is made to work with the GPMC, disable it too.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 2 ++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 8 --------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 8 --------
 3 files changed, 2 insertions(+), 16 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +2 -0
index d6218038055a..c96df4b9b3d7 100644
@@ -1381,6 +1381,7 @@ gpmc0: memory-controller@3b000000 {
 		#interrupt-cells = <2>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		status = "disabled";
 	};
 
 	elm0: ecc@25010000 {
@@ -1390,5 +1391,6 @@ elm0: ecc@25010000 {
 		power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 54 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 };
arch/arm64/boot/dts/ti/k3-am642-evm.dts +0 -8
index 666f5d3a2d95..39feea78a084 100644
@@ -589,11 +589,3 @@ &main_mcan1 {
 	pinctrl-0 = <&main_mcan1_pins_default>;
 	phys = <&transceiver2>;
 };
-
-&gpmc0 {
-	status = "disabled";
-};
-
-&elm0 {
-	status = "disabled";
-};
arch/arm64/boot/dts/ti/k3-am642-sk.dts +0 -8
index 3e6df16fcb59..2e2d40da360a 100644
@@ -566,11 +566,3 @@ &ecap0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_ecap0_pins_default>;
 };
-
-&gpmc0 {
-	status = "disabled";
-};
-
-&elm0 {
-	status = "disabled";
-};
Signature · 1 line
2.37.3
#3 lore raw

PATCH 3/10 arm64: dts: ti: k3-am64: Enable SPI nodes at the board level

In reply to Andrew Davis

SPI nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information.

As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the SPI nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 5 +++++
 arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi  | 2 ++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 9 +--------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 8 --------
 4 files changed, 8 insertions(+), 16 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +5 -0
index fdcacf78f4a6..375078ca4fdd 100644
@@ -370,6 +370,7 @@ main_spi0: spi@20100000 {
 		clocks = <&k3_clks 141 0>;
 		dmas = <&main_pktdma 0xc300 0>, <&main_pktdma 0x4300 0>;
 		dma-names = "tx0", "rx0";
+		status = "disabled";
 	};
 
 	main_spi1: spi@20110000 {
@@ -380,6 +381,7 @@ main_spi1: spi@20110000 {
 		#size-cells = <0>;
 		power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 142 0>;
+		status = "disabled";
 	};
 
 	main_spi2: spi@20120000 {
@@ -390,6 +392,7 @@ main_spi2: spi@20120000 {
 		#size-cells = <0>;
 		power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 143 0>;
+		status = "disabled";
 	};
 
 	main_spi3: spi@20130000 {
@@ -400,6 +403,7 @@ main_spi3: spi@20130000 {
 		#size-cells = <0>;
 		power-domains = <&k3_pds 144 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 144 0>;
+		status = "disabled";
 	};
 
 	main_spi4: spi@20140000 {
@@ -410,6 +414,7 @@ main_spi4: spi@20140000 {
 		#size-cells = <0>;
 		power-domains = <&k3_pds 145 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 145 0>;
+		status = "disabled";
 	};
 
 	main_gpio_intr: interrupt-controller@a00000 {
arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi +2 -0
index 5ce8ceb3779d..38ddf0b3b8a0 100644
@@ -60,6 +60,7 @@ mcu_spi0: spi@4b00000 {
 		#size-cells = <0>;
 		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 147 0>;
+		status = "disabled";
 	};
 
 	mcu_spi1: spi@4b10000 {
@@ -70,6 +71,7 @@ mcu_spi1: spi@4b10000 {
 		#size-cells = <0>;
 		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 148 0>;
+		status = "disabled";
 	};
 
 	mcu_gpio_intr: interrupt-controller@4210000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +1 -8
index 3903e907244e..12d971c3bc3a 100644
@@ -379,15 +379,8 @@ &mcu_gpio0 {
 	status = "reserved";
 };
 
-&mcu_spi0 {
-	status = "disabled";
-};
-
-&mcu_spi1 {
-	status = "disabled";
-};
-
 &main_spi0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_spi0_pins_default>;
 	ti,pindir-d0-out-d1-in;
arch/arm64/boot/dts/ti/k3-am642-sk.dts +0 -8
index 56763d839e05..1a116593a771 100644
@@ -375,14 +375,6 @@ exp2: gpio@60 {
 	};
 };
 
-&mcu_spi0 {
-	status = "disabled";
-};
-
-&mcu_spi1 {
-	status = "disabled";
-};
-
 /* mcu_gpio0 is reserved for mcu firmware usage */
 &mcu_gpio0 {
 	status = "reserved";
Signature · 1 line
2.37.3
#5 lore raw

PATCH 5/10 arm64: dts: ti: k3-am64: Enable ECAP nodes at the board level

In reply to Andrew Davis

ECAP nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information. (These and the EPWM nodes could be used to trigger internal actions but they are not used like that currently)

As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the ECAP nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 3 +++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 9 +--------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 9 +--------
 3 files changed, 5 insertions(+), 16 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +3 -0
index 672575f44529..ef1833f65bdc 100644
@@ -988,6 +988,7 @@ ecap0: pwm@23100000 {
 		power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 51 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	ecap1: pwm@23110000 {
@@ -997,6 +998,7 @@ ecap1: pwm@23110000 {
 		power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 52 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	ecap2: pwm@23120000 {
@@ -1006,6 +1008,7 @@ ecap2: pwm@23120000 {
 		power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 53 0>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_rti0: watchdog@e000000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +1 -8
index cef3afa10c39..43d50ecfb211 100644
@@ -567,19 +567,12 @@ &pcie0_ep {
 };
 
 &ecap0 {
+	status = "okay";
 	/* PWM is available on Pin 1 of header J12 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_ecap0_pins_default>;
 };
 
-&ecap1 {
-	status = "disabled";
-};
-
-&ecap2 {
-	status = "disabled";
-};
-
 &icssg0_mdio {
 	status = "disabled";
 };
arch/arm64/boot/dts/ti/k3-am642-sk.dts +1 -8
index 51f4ae165c13..8b9987ccdc1b 100644
@@ -566,19 +566,12 @@ &pcie0_ep {
 };
 
 &ecap0 {
+	status = "okay";
 	/* PWM is available on Pin 1 of header J3 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_ecap0_pins_default>;
 };
 
-&ecap1 {
-	status = "disabled";
-};
-
-&ecap2 {
-	status = "disabled";
-};
-
 &icssg0_mdio {
 	status = "disabled";
 };
Signature · 1 line
2.37.3
#6 lore raw

PATCH 6/10 arm64: dts: ti: k3-am64: Enable PCIe nodes at the board level

In reply to Andrew Davis

PCIe nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with a SerDes PHY. And usually only one of the two modes can be used at a time as they share a SerDes link.

As the PHY and mode is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the PCIe nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 2 ++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 2 +-
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 8 --------
 3 files changed, 3 insertions(+), 9 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +2 -0
index ef1833f65bdc..b193f88a7a0f 100644
@@ -871,6 +871,7 @@ pcie0_rc: pcie@f102000 {
 		ranges = <0x01000000 0x00 0x68001000  0x00 0x68001000  0x00 0x0010000>,
 			 <0x02000000 0x00 0x68011000  0x00 0x68011000  0x00 0x7fef000>;
 		dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x00000010 0x0>;
+		status = "disabled";
 	};
 
 	pcie0_ep: pcie-ep@f102000 {
@@ -889,6 +890,7 @@ pcie0_ep: pcie-ep@f102000 {
 		clocks = <&k3_clks 114 0>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <1>;
+		status = "disabled";
 	};
 
 	epwm0: pwm@23000000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +1 -1
index 43d50ecfb211..2dec25d90240 100644
@@ -553,6 +553,7 @@ serdes0_pcie_link: phy@0 {
 };
 
 &pcie0_rc {
+	status = "okay";
 	reset-gpios = <&exp1 5 GPIO_ACTIVE_HIGH>;
 	phys = <&serdes0_pcie_link>;
 	phy-names = "pcie-phy";
@@ -563,7 +564,6 @@ &pcie0_ep {
 	phys = <&serdes0_pcie_link>;
 	phy-names = "pcie-phy";
 	num-lanes = <1>;
-	status = "disabled";
 };
 
 &ecap0 {
arch/arm64/boot/dts/ti/k3-am642-sk.dts +0 -8
index 8b9987ccdc1b..58c71608d925 100644
@@ -557,14 +557,6 @@ &main_r5fss1_core1 {
 			<&main_r5fss1_core1_memory_region>;
 };
 
-&pcie0_rc {
-	status = "disabled";
-};
-
-&pcie0_ep {
-	status = "disabled";
-};
-
 &ecap0 {
 	status = "okay";
 	/* PWM is available on Pin 1 of header J3 */
Signature · 1 line
2.37.3
#2 lore raw

PATCH 2/10 arm64: dts: ti: k3-am64: Enable I2C nodes at the board level

In reply to Andrew Davis

I2C nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information.

As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the I2C nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi |  4 ++++
 arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi  |  2 ++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  |  9 +--------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 13 +------------
 4 files changed, 8 insertions(+), 20 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +4 -0
index a115c668d001..fdcacf78f4a6 100644
@@ -321,6 +321,7 @@ main_i2c0: i2c@20000000 {
 		power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 102 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_i2c1: i2c@20010000 {
@@ -332,6 +333,7 @@ main_i2c1: i2c@20010000 {
 		power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 103 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_i2c2: i2c@20020000 {
@@ -343,6 +345,7 @@ main_i2c2: i2c@20020000 {
 		power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 104 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_i2c3: i2c@20030000 {
@@ -354,6 +357,7 @@ main_i2c3: i2c@20030000 {
 		power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 105 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	main_spi0: spi@20100000 {
arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi +2 -0
index 1181ad017626..5ce8ceb3779d 100644
@@ -37,6 +37,7 @@ mcu_i2c0: i2c@4900000 {
 		power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 106 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	mcu_i2c1: i2c@4910000 {
@@ -48,6 +49,7 @@ mcu_i2c1: i2c@4910000 {
 		power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 107 2>;
 		clock-names = "fck";
+		status = "disabled";
 	};
 
 	mcu_spi0: spi@4b00000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +1 -8
index 78f246077ca9..3903e907244e 100644
@@ -336,6 +336,7 @@ &main_uart1 {
 };
 
 &main_i2c1 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
@@ -378,14 +379,6 @@ &mcu_gpio0 {
 	status = "reserved";
 };
 
-&mcu_i2c0 {
-	status = "disabled";
-};
-
-&mcu_i2c1 {
-	status = "disabled";
-};
-
 &mcu_spi0 {
 	status = "disabled";
 };
arch/arm64/boot/dts/ti/k3-am642-sk.dts +1 -12
index 8423295150fc..56763d839e05 100644
@@ -349,15 +349,8 @@ &main_uart1 {
 	status = "reserved";
 };
 
-&mcu_i2c0 {
-	status = "disabled";
-};
-
-&mcu_i2c1 {
-	status = "disabled";
-};
-
 &main_i2c1 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
@@ -382,10 +375,6 @@ exp2: gpio@60 {
 	};
 };
 
-&main_i2c3 {
-	status = "disabled";
-};
-
 &mcu_spi0 {
 	status = "disabled";
 };
Signature · 1 line
2.37.3
#0 lore raw

cover AM64x Disable Incomplete DT Nodes

Hello all,

This series goes through the AM64x dtsi and disables the set of nodes that are not functional without additional board level information. This is usually pinmux data, but can also be inernal device resources.

Only when the node is completed in the board file should the node be enabled. This helps prevents nodes that represent IP that are not pinned-out on a given board from being left enabled.

This also reduces the effort needed to add a new board, one no longer needs to manually disable all the extra IP. For instance TI J784s4 has 20(!) MCAN instances. It is much easier to enable the one you pin out, vs disabling the 19 that you did not.

Thanks,
Andrew

Andrew Davis (10):
arm64: dts: ti: k3-am64: Enable UART nodes at the board level
arm64: dts: ti: k3-am64: Enable I2C nodes at the board level
arm64: dts: ti: k3-am64: Enable SPI nodes at the board level
arm64: dts: ti: k3-am64: Enable EPWM nodes at the board level
arm64: dts: ti: k3-am64: Enable ECAP nodes at the board level
arm64: dts: ti: k3-am64: Enable PCIe nodes at the board level
arm64: dts: ti: k3-am64: MDIO pinmux should belong to the MDIO node
arm64: dts: ti: k3-am64: Enable MDIO nodes at the board level
arm64: dts: ti: k3-am64: Enable MCAN nodes at the board level
arm64: dts: ti: k3-am64: Enable GPMC and ELM nodes at the board level

 arch/arm64/boot/dts/ti/k3-am64-main.dtsi |  37 ++++++
 arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi  |   6 +
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 119 ++-----------------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 142 ++---------------------
 4 files changed, 63 insertions(+), 241 deletions(-)
Signature · 1 line
2.37.3
#7 lore raw

PATCH 7/10 arm64: dts: ti: k3-am64: MDIO pinmux should belong to the MDIO node

Although usually integrated as a child of an Ethernet controller, MDIO IP has an independent pinout. This pinout should be controlled by the MDIO node (so if it was to be disabled for instance, the pinmux state would reflect that).

Move the MDIO pins pinmux to the MIDO nodes.

---
 arch/arm64/boot/dts/ti/k3-am642-evm.dts | 6 ++++--
 arch/arm64/boot/dts/ti/k3-am642-sk.dts  | 6 ++++--
 2 files changed, 8 insertions(+), 4 deletions(-)
arch/arm64/boot/dts/ti/k3-am642-evm.dts +4 -2
index 2dec25d90240..2319ba4f5ae3 100644
@@ -425,8 +425,7 @@ &usb0 {
 
 &cpsw3g {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mdio1_pins_default
-		     &rgmii1_pins_default
+	pinctrl-0 = <&rgmii1_pins_default
 		     &rgmii2_pins_default>;
 };
 
@@ -441,6 +440,9 @@ &cpsw_port2 {
 };
 
 &cpsw3g_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio1_pins_default>;
+
 	cpsw3g_phy0: ethernet-phy@0 {
 		reg = <0>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
arch/arm64/boot/dts/ti/k3-am642-sk.dts +4 -2
index 58c71608d925..c1d634647027 100644
@@ -439,8 +439,7 @@ &usb0 {
 
 &cpsw3g {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mdio1_pins_default
-		     &rgmii1_pins_default
+	pinctrl-0 = <&rgmii1_pins_default
 		     &rgmii2_pins_default>;
 };
 
@@ -455,6 +454,9 @@ &cpsw_port2 {
 };
 
 &cpsw3g_mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio1_pins_default>;
+
 	cpsw3g_phy0: ethernet-phy@0 {
 		reg = <0>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
Signature · 1 line
2.37.3
#1 lore raw

PATCH 1/10 arm64: dts: ti: k3-am64: Enable UART nodes at the board level

In reply to Andrew Davis

UART nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information.

As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the UART nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi |  7 ++++++
 arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi  |  2 ++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 29 +-----------------------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 29 +-----------------------
 4 files changed, 11 insertions(+), 56 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +7 -0
index d6aa23681bbe..a115c668d001 100644
@@ -237,6 +237,7 @@ main_uart0: serial@2800000 {
 		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 146 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart1: serial@2810000 {
@@ -248,6 +249,7 @@ main_uart1: serial@2810000 {
 		power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 152 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart2: serial@2820000 {
@@ -259,6 +261,7 @@ main_uart2: serial@2820000 {
 		power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 153 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart3: serial@2830000 {
@@ -270,6 +273,7 @@ main_uart3: serial@2830000 {
 		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 154 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart4: serial@2840000 {
@@ -281,6 +285,7 @@ main_uart4: serial@2840000 {
 		power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 155 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart5: serial@2850000 {
@@ -292,6 +297,7 @@ main_uart5: serial@2850000 {
 		power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 156 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_uart6: serial@2860000 {
@@ -303,6 +309,7 @@ main_uart6: serial@2860000 {
 		power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 158 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	main_i2c0: i2c@20000000 {
arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi +2 -0
index 02d4285acbb8..1181ad017626 100644
@@ -14,6 +14,7 @@ mcu_uart0: serial@4a00000 {
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 149 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	mcu_uart1: serial@4a10000 {
@@ -24,6 +25,7 @@ mcu_uart1: serial@4a10000 {
 		power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 160 0>;
 		clock-names = "fclk";
+		status = "disabled";
 	};
 
 	mcu_i2c0: i2c@4900000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +1 -28
index 5cf913860f80..78f246077ca9 100644
@@ -325,6 +325,7 @@ AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (C17) MCAN1_TX */
 };
 
 &main_uart0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
 };
@@ -334,34 +335,6 @@ &main_uart1 {
 	status = "reserved";
 };
 
-&main_uart2 {
-	status = "disabled";
-};
-
-&main_uart3 {
-	status = "disabled";
-};
-
-&main_uart4 {
-	status = "disabled";
-};
-
-&main_uart5 {
-	status = "disabled";
-};
-
-&main_uart6 {
-	status = "disabled";
-};
-
-&mcu_uart0 {
-	status = "disabled";
-};
-
-&mcu_uart1 {
-	status = "disabled";
-};
-
 &main_i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
arch/arm64/boot/dts/ti/k3-am642-sk.dts +1 -28
index 738d0cf6c40a..8423295150fc 100644
@@ -338,15 +338,8 @@ AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
 	};
 };
 
-&mcu_uart0 {
-	status = "disabled";
-};
-
-&mcu_uart1 {
-	status = "disabled";
-};
-
 &main_uart0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
 };
@@ -356,26 +349,6 @@ &main_uart1 {
 	status = "reserved";
 };
 
-&main_uart2 {
-	status = "disabled";
-};
-
-&main_uart3 {
-	status = "disabled";
-};
-
-&main_uart4 {
-	status = "disabled";
-};
-
-&main_uart5 {
-	status = "disabled";
-};
-
-&main_uart6 {
-	status = "disabled";
-};
-
 &mcu_i2c0 {
 	status = "disabled";
 };
Signature · 1 line
2.37.3
#9 lore raw

PATCH 9/10 arm64: dts: ti: k3-am64: Enable MCAN nodes at the board level

In reply to Andrew Davis

MCAN nodes defined in the top-level AM64x SoC dtsi files are incomplete and will not be functional unless they are extended with pinmux information.

As the pinmux is only known at the board integration level, these nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that are actually pinned out on a given board.

---
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 2 ++
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 2 ++
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 8 --------
 3 files changed, 4 insertions(+), 8 deletions(-)
arch/arm64/boot/dts/ti/k3-am64-main.dtsi +2 -0
index 7ea07f7fe5a2..d6218038055a 100644
@@ -1326,6 +1326,7 @@ main_mcan0: can@20701000 {
 			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "int0", "int1";
 		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
 	};
 
 	main_mcan1: can@20711000 {
@@ -1340,6 +1341,7 @@ main_mcan1: can@20711000 {
 			     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "int0", "int1";
 		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+		status = "disabled";
 	};
 
 	crypto: crypto@40900000 {
arch/arm64/boot/dts/ti/k3-am642-evm.dts +2 -0
index 9a3bf852810c..666f5d3a2d95 100644
@@ -577,12 +577,14 @@ &ecap0 {
 };
 
 &main_mcan0 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mcan0_pins_default>;
 	phys = <&transceiver1>;
 };
 
 &main_mcan1 {
+	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mcan1_pins_default>;
 	phys = <&transceiver2>;
arch/arm64/boot/dts/ti/k3-am642-sk.dts +0 -8
index 451e1483f3e4..3e6df16fcb59 100644
@@ -567,14 +567,6 @@ &ecap0 {
 	pinctrl-0 = <&main_ecap0_pins_default>;
 };
 
-&main_mcan0 {
-	status = "disabled";
-};
-
-&main_mcan1 {
-	status = "disabled";
-};
-
 &gpmc0 {
 	status = "disabled";
 };
Signature · 1 line
2.37.3
Reviewed-by on the v1 series
#11 lore raw
In reply to Andrew Davis

On October 17, 2022 thus sayeth Andrew Davis:

Quoted 30 lines

Hello all,

This series goes through the AM64x dtsi and disables the set of nodes that are not functional without additional board level information. This is usually pinmux data, but can also be inernal device resources.

Only when the node is completed in the board file should the node be enabled. This helps prevents nodes that represent IP that are not pinned-out on a given board from being left enabled.

This also reduces the effort needed to add a new board, one no longer needs to manually disable all the extra IP. For instance TI J784s4 has 20(!) MCAN instances. It is much easier to enable the one you pin out, vs disabling the 19 that you did not.

Thanks,
Andrew

Andrew Davis (10):
arm64: dts: ti: k3-am64: Enable UART nodes at the board level
arm64: dts: ti: k3-am64: Enable I2C nodes at the board level
arm64: dts: ti: k3-am64: Enable SPI nodes at the board level
arm64: dts: ti: k3-am64: Enable EPWM nodes at the board level
arm64: dts: ti: k3-am64: Enable ECAP nodes at the board level
arm64: dts: ti: k3-am64: Enable PCIe nodes at the board level
arm64: dts: ti: k3-am64: MDIO pinmux should belong to the MDIO node
arm64: dts: ti: k3-am64: Enable MDIO nodes at the board level
arm64: dts: ti: k3-am64: Enable MCAN nodes at the board level
arm64: dts: ti: k3-am64: Enable GPMC and ELM nodes at the board level

Quoted 6 lines
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi |  37 ++++++
 arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi  |   6 +
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 119 ++-----------------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 142 ++---------------------
 4 files changed, 63 insertions(+), 241 deletions(-)

I wholeheartedly agree! This looks great to me!

~Bryan

maintainer Acked-by on the v1 series
#12 lore raw
In reply to Andrew Davis
Quoted 12 lines · Andrew Davis

Andrew Davis (10):
arm64: dts: ti: k3-am64: Enable UART nodes at the board level
arm64: dts: ti: k3-am64: Enable I2C nodes at the board level
arm64: dts: ti: k3-am64: Enable SPI nodes at the board level
arm64: dts: ti: k3-am64: Enable EPWM nodes at the board level
arm64: dts: ti: k3-am64: Enable ECAP nodes at the board level
arm64: dts: ti: k3-am64: Enable PCIe nodes at the board level
arm64: dts: ti: k3-am64: MDIO pinmux should belong to the MDIO node
arm64: dts: ti: k3-am64: Enable MDIO nodes at the board level
arm64: dts: ti: k3-am64: Enable MCAN nodes at the board level
arm64: dts: ti: k3-am64: Enable GPMC and ELM nodes at the board level

Quoted 5 lines
 arch/arm64/boot/dts/ti/k3-am64-main.dtsi |  37 ++++++
 arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi  |   6 +
 arch/arm64/boot/dts/ti/k3-am642-evm.dts  | 119 ++-----------------
 arch/arm64/boot/dts/ti/k3-am642-sk.dts   | 142 ++---------------------
 4 files changed, 63 insertions(+), 241 deletions(-)
Signature · 2 lines
Regards
Vignesh
maintainer Applied
#13 lore raw
In reply to Andrew Davis

Hi Andrew Davis,

Quoted 9 lines · Andrew Davis

This series goes through the AM64x dtsi and disables the set of nodes that are not functional without additional board level information. This is usually pinmux data, but can also be inernal device resources.

Only when the node is completed in the board file should the node be enabled. This helps prevents nodes that represent IP that are not pinned-out on a given board from being left enabled.

[...]

I have applied the following to branch ti-k3-dts-next on [1]. Thank you!

[01/10] arm64: dts: ti: k3-am64: Enable UART nodes at the board level

        commit: dacf4705cee54eef4406a886a0a50a6f445969f8
[02/10] arm64: dts: ti: k3-am64: Enable I2C nodes at the board level
        commit: b80f75d8f68cad4efa250e4a3152932f59c756cc
[03/10] arm64: dts: ti: k3-am64: Enable SPI nodes at the board level
        commit: 79d4aa623f6c9d47aa29b6b4a3fa46c09f74bfae
[04/10] arm64: dts: ti: k3-am64: Enable EPWM nodes at the board level
        commit: ebc0ed718da346d651b356cb71dddfb747c934fa
[05/10] arm64: dts: ti: k3-am64: Enable ECAP nodes at the board level
        commit: dcac8eaaa90fe2c84761cf55a3e989ca5774d2f5
[06/10] arm64: dts: ti: k3-am64: Enable PCIe nodes at the board level
        commit: 3e21ec289c76dbc88dc306802122214b6b053a99
[07/10] arm64: dts: ti: k3-am64: MDIO pinmux should belong to the MDIO node
        commit: aa62d661247f180d0fc534e880cb6bc7fb50b4a1
[08/10] arm64: dts: ti: k3-am64: Enable MDIO nodes at the board level
        commit: f572888b3c10bf12436423e854f6ee6e3872c570
[09/10] arm64: dts: ti: k3-am64: Enable MCAN nodes at the board level
        commit: 4a57988707d7c7502842de07d6c8649da5a844fc
[10/10] arm64: dts: ti: k3-am64: Enable GPMC and ELM nodes at the board level
        commit: 4eb7aa3befa33c05a03d11fd3b4bb8b74d3c68c0

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

[1] git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git

Signature · 3 lines
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D